Search Documents

By Wils L. Cooley

The report covers tests and criteria for the establishment of safe grounding systems for coal mines. The work deals primarily with under-ground coal mines, but much is applicable to surface mines as well. Included is an extensive guide to grounding and bonding procedures for mine surface substations. Xit-Rods are evaluated and shown to deviate from manufacturer's claims. An analysis shows that very long cables are difficult to monitor using audio frequency ground-check techniques. A method is developed to detect failing cable splices without removing the cable from service. Simulation and measurement are compared for a technique to detect bad rail bonds, and an assessment is made of grounding techniques for dc face equipment.

Jan 1, 1979

By Geoffrey C. Hebner

Augered, cast-in-place piles (ACIP) have become a very common foundation type in Atlanta and the Southern Piedmont Province as well as much of the United States in the past 20 years. Prior to the introduction of ACIP foundations in Atlanta, the most common deep foundation type was Raymond piles. Raymond piles are basically a driven, thin-walled step-tapered steel pile filled with concrete. Drilled piers were also relatively common and continue to be used, particularly in shallow bedrock or high column load situations. Driven piles, including pipes, H-sections, and timber piles were previously common with working loads typically in the 30 to 50-ton range. Initially, ACIP foundations had similar allowable capacities, however, over time improvements in installation techniques and equipment have resulted in an increase in allowable ACIP capacities. Correspondingly, they have become a more cost-effective and trusted foundation for geotechnical and structural engineers. Over the next several decades many other deep foundation alternatives began to lose popularity. ACIP are one of the predominant deep foundations in Atlanta and the Southern Piedmont today. Although ACIP foundations have widespread popularity in the private sector, they have not been readily accepted currently by government transportation agencies. ACIP may be used by some of the smaller municipalities, but to the author's knowledge, have not been used with regularity by larger, state agencies.

Jan 1, 2003

By M. M. Ayoub

This volume is the second of three volumes comprising the final report of the research project "Biomechanics of Low Coal." It covers only the anthropometric study of low coal miners. Volume I summarizes the overall biomechanical, anthropometry, and work physiology study conducted. Development of work clothes modified to meet the needs of low coal miners is described in Volume III. The male and female anthropometry, with the exception of weight and circumferential dimensions, was quite similar to the comparison populations. The miners tended to be heavier and have greater circumferences. The measurements made in this study were used to develop 5th, 50th and 95th percentile, quarter and half scale, male and female mannequins. These twelve mannequins can be used in work place and equipment design and redesign.

Jan 1, 1982

By Dennis E. Jensen

Field studies were performed during blasting operations for strip coal mining above the room and pillar workings at Jenny mine in eastern Kentucky. The study is part of the Bureau of Mines program to develop criteria for the proximity of surface blasting to underground mines. Measurements and observations were made to identify physical changes in the mine. No change in the frequency of roof falls or any other indication of apparent damage was noted. Recordings of blast induced vibrations were made using sensors on the roof and floor of the underground mine and at the ground surface. A maximum particle velocity of 17.5 in/sec was recorded on the mine roof. The vibration data were analyzed and comparisons were made between roof vibration levels and those recorded on the mine floor and at the ground surface. Results are compared with previous blast vibration studies. Recommendations are made for further study toward developing criteria.

Jan 1, 1979

By Larry L. Wischhoefer

The Automated Breathing Metabolic Simulator (ABMS) is a versatile machine capable of performing almost any physiologically appropriate respiratory simulation. The first ABMS was delivered to the Bureau of Mines by IBM in 1973. Since then efforts have been made to refine the systems and components which make up the ABMS including the Breathing Simulator Module (BSM), Gas Analysis Module (GAM), and Supervisory Controller (SC)-each of which are also capable of stand-alone operation. Since September 1980, Reimers Consultants has been testing and modifying the ABMS and its components in order to improve the equipment and to develop simulation criteria and parameters. Changes have been made to the Phase I Design Plan and Performance Specifications; future improvements based on current experience are recommended; and test results of full scale testing conducted by Reimers Consultants in November 1983 on several types of breathing apparatus are reported and illustrated.

Jan 1, 1984

During the initial portion of the contract several alternative designs were considered, as set out step by step in the monthly reports. The conclusions reached during this period were - to use on INTERDATA Model 70 as the system minicomputer - to drop the idea of multiplexing and digitizing the inclinometer outputs downhole due to the greater complexity and cost that that alternative would imply - to use a multitasking software monitor to enable synchronization of the several tasks that the system would have to perform simultaneously - to use a common controller for all I/0 devices except those which were available off the shelf from Interdata - to use a sheave counter to meter off equal increments of probe travel, but to supplement this information with the use of an encoder on the winch drum in order to be able to measure total probe travel unambiguously. - to place all I10 device interfaces in a bin connected to the common controller. During this period considerable attention was dedicated to the design of the mechanical components contemplated it the original contract. Of these, only those required for vertical probe was complete at the time that it was decided to forego the mechanical subsystem and concentrate on developing the necessary electronics and software to interface with the probes being developed by the Bureau of Mines.

Jan 1, 2012

By Robert Stefanko

This report, rather than attempting to replace previous annual reports, supplements, and more importantly, coordinates and summarizes the entire effort. Even with such restrictions, the report is voluminous and, therefore, a decision has been made to divide it into two parts. The first volume is basically narrative and includes tabular results and analyses. The second volume is in appendix form giving detailed information. Together, they permit a logical discussion of all aspects of the project (Volume I) without cumbersome distractions but, at the same time, provide all the details to permit others to evaluate and explain the results or develop similar research programs (Volume II). The aim of the original proposal was basically to develop instruments and techniques and then make measurements of suitable power parameters, ground fault currents and ground resistance beds. With such information available, it was possible to develop a meaningful simulator which would permit investigating electrical systems and components on paper without costly trial and error procedures in the third year, a cable splice testing program was added to the project. While there were the usual delays attendant in such original research, these objectives were achieved.

Jan 1, 1973

By Jack Kadlecik

This final technical report describes the concept feasibility study, testing, design and development effort which went into. The quick opening enclosure access cover and flame path tolerance checking system. A detailed definition of the explosion-proof multiple start threads is shown for two (2) sized electrical enclosures.

Jan 1, 1972

By Andrew M. Leszcykowski

In 1984, personnel from the U.S. Bureau of Mines examined 41,550 acres of the North Fork Owyhee River Wilderness Study Area for mineral resources. This study area, in southwestern Idaho, is underlain by tuffs and basalt of Tertiary age. There are no known mines, claims, or prospects in or near the area. The northeast and southwest corners of the area are covered by oil and gas leases or lease applications, but no known exploration has been conducted. On Nickel Creek and Pleasant Valley Tables, in the southern part of the area, thin flows of vesicular, moss-covered basalt occur that are suitable for use as decorative building stone. The stone available for exploitation crops out over several square miles. However, more suitable material, outside the study area, is closer to potential markets.

Jan 1, 1986

By John E. Trombly

System objectives and design criteria for an in-mine ULF radio paging system are discussed Coding formats, frequency and bandwidth selection criteria leading to the system design are discussed. The prototype call alert transmitter and pocket page receiver is functionally described. The report includes circuit descriptions, schematics, parts lists, printed circuit fabrication and assembly drawings. The report concludes with an estimate of the manufacturing cost for each assembly.

Jan 1, 2011

By Geoffrey D. Collins

This paper deals with the construction of the Effluent Outfall Diffusers which form part of the outfall for the Deer Island sewage project. The work was executed 15 km out to sea in Massachusetts Bay and required the drilling, installation, grouting and accurate determination of the actual position of 55 riser shafts in 33.5 m deep water. Although not strictly a "foundation", the contractor's approach to the installation of the diffusers was a logical development from many marine foundation projects executed by the Contracting companies over the last decades. The only previous application of this design of outfall had been in Australia where offshore oil drilling techniques had been adapted for use in riser installation.

Jan 1, 1994

By Jon G. Bredeson

The electromagnetic noise that exists in a mining environment is quite severe and was shown to have been reasonably well documented by a number of researchers in the Phase I Report. The noise levels are such that prudent communication design requires the careful use of all the electromagnetic noise data available. A comprehensive survey was undertaken to determine techniques used in various industrial environments to achieve secure communications in the presence of electromagnetic interference. The techniques were given in the Phase I Report and are rudimentary, but have produced reasonably good results. A number of these techniques could be applied to the mining environment.

Jan 1, 1980

By C. Pritchard

John Marks said in his acceptance of the Hartman Award in 2008 ? ?I guess that without the occasional complaint, your mine is probably over-ventilated? (Marks, 2008). Miners are seldom in this situation and often spend much of the time trying to find enough air to keep the operation running. With examination there are some things that can be done to make the best use of ventilation systems. Should there be surplus air, in which some of these options may result - financial and other benefits can be obtained. Some of the issues mine operators have needed to address recently are increased airflow requirements to dilute diesel particulates in metal and non-metal mines. Also, operations are faced with demands from reserves that are deeper, hotter and further away from fans and shafts, not to mention increased production demands. Mine ventilation air is a costly commodity, especially by the time it has been heated or cooled and moved to the bottom of the shaft and through the mine airways. Most of the options presented in this paper are useful for metal non-metal operations but some may be applicable to coal too. OPTIONS FOR IMPROVEMENT Some of the areas to be addressed are shop ventilation methods, auxiliary equipment areas, dedicated intakes and returns, optimizing development, examination of mine airway utilization and alternative ventilation methods. UNDERGROUND SHOPS First, examine what is being done with the underground shop air. If it is being coursed directly to the returns there may be some potential to better utilize this, in most cases, relatively contaminant free air. Research the legal options for ventilating mine shops. MSHA regulations in 30CFR 57.4761 (1) allow the following options: To confine or prevent the spread of toxic gases from a fire originating in an underground shop where maintenance work is routinely done on mobile equipment, one of the following measures shall be taken: use of control doors or bulkheads, routing of the mine shop air directly to an exhaust system, reversal of mechanical ventilation, or use of an automatic fire suppression system in conjunction with an alternate escape route. The alternative used shall at all times provide at least the same degree of safety as control doors or bulkheads. Discussion This regulation gives some operators flexibility in ventilating underground shop facilities. If shop air is to be coursed through the work area, and then directly to the mine return, the question should be asked ? is the quality of air good enough to be reused in the mine, and if so, what are the risks? Can the risks be accommodated and managed to accomplish the change? If so, a considerable increase in mine level airflow could be attained by reusing shop air. Clearly, regulations are a minimum standard, and can be exceeded. Metal non-metal mine regulations are not as specific as coal due to the multitude of different mining methods and conditions utilized. Risks must be thoroughly examined and addressed to assure a safe environment. Issues Determine what contaminants are being produced in the work area ? welding fumes, diesel exhaust, paint fumes, chemicals and solvents, etc. Survey the area and determine exposures. MSHA requires exposure monitoring in 30 CFR 57.5002 (1) of dust, gasses mists and fumes to assure air quality is being met. Perform surveys and examine existing data to quantify personal and area concentrations of contaminants. Often there is adequate circulation such that exposure levels in shop work areas are low. After sending shop air back into the system any contaminants would be further lowered by dilution with other mine intake air downstream. Look at the shop work schedule. If only on day shift, the other two shifts and possibly weekends have no activity or source of contamination to affect the ventilation system. The worst case planning scenario would be a shop fire. Study and simulate how this would affect the mine and shop area. MSHA regulations require an escape route and a fire suppression system be installed and maintained as follows in 30 CFR 57.4671 (1): (d) Automatic fire suppression system and escape route. If used as an alternative, the automatic fire suppression system and alternate escape route shall meet the following requirements: (1) The suppression system shall be? (d)(1)(i) Located in the shop area; (d)(1)(ii) The appropriate size and type for the particular fire hazards involved; and (d)(1)(iii) Inspected at weekly intervals and properly maintained. (2) The escape route shall bypass the shop area so that the route will not be affected by a fire in the shop area. Case Study In an underground room and pillar mine, active mine workings were advancing further away from the mine shaft with deteriorated returns and leakage having a negative effect on ventilation airflows to the face. Mine level airflows were 236 m3/s (500,000 cfm) and shop airflows were 24 m3/s (50,000 cfm) (see Figure 1A). No additional capacity was available at the main surface fan. A solution was to utilize the shop air then send it to the mine areas instead of directly to the return. Considerable information on shop air quality and exposures from many years of operation was examined and no negative data was discovered. A risk analysis determined that moving forward with a shop air reuse program was desirable. A plan was developed, analyzed and decision to proceed approved by mine management. The change was simulated on the computer with the USBM/MTU MFire program before being implemented. This included utilizing fire scenarios to examine potential exposures to inby mining sections and plan escape routes. A monitoring system was designed and installed in cooperation with the US Bureau of Mines to monitor carbon monoxide

Jan 1, 2009

By N Currey, G Corder, G Becker

"The SUSOP« Framework is a new technique that helps incorporate sustainable development principles and objectives into the design and operation of businesses. Developed through the Co-operative Research Centre for Sustainable Resource Processing, it brings a design methodology to sustainability, similar to what hazard and risk techniques such as HAZOP did for safety.Metallica Minerals Limited (æMetallicaÆ) adopted the SUSOP« framework to help identify opportunities and risks that could directly improve or affect its flagship SCONI (nickel-cobalt and scandium) project. This project has the potential to become the worldÆs largest producer of scandium oxide (æscandiaÆ) which is used in solid oxide fuel cells and strengthens aluminium alloys. Located northwest of Townsville in Queensland, the plant site will be located within the previously mined and partially rehabilitated Greenvale Nickel Mine. By applying the SUSOP« framework through a series of multi-disciplinary workshops and offline analysis, Metallica was able to identify numerous sustainability opportunities and risks. Opportunities were clustered together to form concepts to develop a more holistic understanding of the projectÆs overall potential contribution to sustainable development as well as determine where key risks could be mitigated. Four key concepts were identified: Waste and Water Workforce Community and Enterprise Development Energy and Greenhouse Gases (GHG). Metallica was able to include a range of initiatives that could deliver enhanced environmental, social and community outcomes into their mine development plan. These included measures to reduce reliance on water, reduce the volume of waste, provide local opportunities for training and skilled employment and create support for local enterprise development. These measures also resulted in a significant reduction in the capital estimate of the project.This paper provides an overview of the SUSOP« framework, details its application to the SCONI project and discusses the outcomes that will help establish the projectÆs strong sustainable development credentials and improved business outcomes.CITATION:Corder, G, Currey, N and Becker, G, 2013. Sustainability, made easy - A business improvement case study, in Proceedings MetPlant 2013, pp 259-271 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By M. Ng

As part of a long-term study of titanium minerals processing being undertaken by the Julius Kruttschnitt Mineral Research Centre, techniques have been developed to measure the resistivity of ilmenite, rutile, zircon and other associated minerals. The techniques have proven reproducible and have allowed the measurement of resistivity under conditions of varying temperature, surface condition and surface moisture adsorption. The measured values can be linked to the separability of the minerals in the dry plant, and hence are useful as a diagnostic test for existing plants when performance deteriorates, or for greenfield sites to investigate potential problems. One of the major problems in electrical separation of titanium minerals is surface coating on the mineral grains. Coatings can make normally conductive minerals such as ilmenite and leucoxene behave much more like non-conductors. Electrical separation of surface contaminated ilmenite from non-conductors then becomes extremely difficult unless the surface contaminant is first removed. The resistivity measurement technique was used to evaluate the effect of surface cleaning on the resistivity of ilmenite and zircon from a Western Australian deposit which will shortly be in production. Ten different attritioning methods were evaluated, ranging from simple rinsing inwater to chemical attritioning in sulphuric acid combined with ultrasonic leaching. A roasting and quenching step was also investigated. As would be expected, the gentler treatments, such as rinsing in water or Calgon, had only amoderate effect on the ilmenite surface coatings. Ilmenite resistivity decreased by about 1 order of magnitude from 5.6 x108?m to between 2.5 and 4.4 x107?m. More intense treatments had a much more pronounced effect. The most effective, reduced ilmenite resistivity to 6.5 x105?m or three orders of magnitude. Zircon was relatively unaffected by any of the attritioning methods, with only a small increase in resistivity observed from 8.0 x1012?m to 2 x1013 ?m. The results show that measurement of mineral resistivity allows the effect of surface treatments to be easily quantified in a way that has benefits for greenfield site development where only small samples are available for testing. The effect of surface moisture has also been investigated using resistivity measurements. Measurements were made on zircon in an environmental chamber in which both humidity and temperature could be closely controlled. Zircon resistivity at 60 deg C decreased from 6 x1011?m at 5% relative humidity to 8 x108?m at 95% humidity. Moisture content and moisture re-adsorption from dry of zircon and number of other minerals were measured using a Mettler moisture analyser. Zircon adsorbed the least amount of surface moisture (0.05–0.09%) but re-adsorbed moisture from dry the fastest, reaching 98% of the original level in 10 minutes. Leucoxene adsorbed the most moisture (0.67%), but was much slower re-adsorbing this moisture from the dry state, reaching only 63% of the original level in 10 minutes. The difference was attributed to the surface characteristics of the grains, the leucoxene being much more porous than the zircon examined. The resistivities and differing rates of moisture adsorption can be used to quantify the effects of changes in atmospheric conditions of the performance of electrical separation in dry plants.

Jan 1, 2003

By V Cullinan, D Buchanan

The Brunswick plant is located in Costerfield, approximately 40km east of Bendigo in central Victoria. Crushing, grinding, gravity gold concentration and flotation methods are used to produce a saleable gold concentrate and an antimony-gold flotation concentrate. This paper discusses the improvements made within the processing plant which have resulted in a 99% increase in throughput over nameplate capacity of 6 250 average tonnes per month to 12 445 average tonnes per month and increases of 12% gold (from 2007 average of 78% to 2014 average of 90%) and 16% antimony recovery (from 2007 average of 79% to 2015 average of 95%). This combined effort has resulted in an increase of equivalent gold ounces (AuEq oz) produced from 2010-2014 of 15 872 to 82 574 – a 66 702 increase.AuEq oz= Au oz +Sb t × Sb (US$/t)Au (US$/oz)CITATION:Buchanan, D and Cullinan, V, 2015. Improvements in bi-metal production at the Brunswick Plant, Costerfield, in Proceedings MetPlant 2015, pp 267–272 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Mike Lovitt

New Gold Inc. had commissioned Orica to assist with the design of the drawbell blasting at New Afton Underground copper/gold block cave at Kamloops, British Columbia, Canada. Orica have had much success in developing the single-shot drawbell method at Freeport Indonesia in 2001 in the Deep Ore Zone and they will be using it exclusively in their new Grasberg Underground Operation. RioTinto Northparkes have also used the single shot drawbell blasting in their Second Lift E26 Project and even in the E48 orebody which is a post undercut block cave, realising the safety and operational benefits of this blasting method.

Jan 1, 2013

By G. Arpa

Ventilation survey using tracer gas measurement is one of the techniques for mine ventilation design, monitoring and investigation of movement of fresh air and contaminants. However, there has been little research into using both tracer gas monitoring and numerical simulation. In this research, tracer gas technique was used for quantitative assessment of airflows through narrow vein shrinkage stopes with various opening shapes and friction factors. SF6 was used as a tracer gas to monitor airflow through three narrow vein shrinkage stopes in order to obtain diffusion concentration curves against elapsed time. The mine ventilation simulator, MIVENA Ver.6, was used to construct the entire ventilation network of the mine to monitor airflows through the stopes. The diffusion concentration curves against elapsed time were simulated with a numerical model. The result shows that the concentration-time curve is unsymmetrical and is skewed to the front of the flow direction. From the results of history-matching between the measured and the simulated curves, volume flow rates of airways and stopes were evaluated. Importantly, the tailing effect of the concentration-time curve between the measured and simulated is greatly improved by reconstructing an equivalent airflow route to represent unused mine openings, dead end drives and other open spaces. Finally, it can be concluded that openings, dead end drives and other open spaces have no relation on flow rates, but affect the airflow quality provided from the inlet portal as shown by tracer gas diffusion characteristics.

Jan 1, 2009

Study on Basic Theory of the Grain Settlement in Fluidised Bed This paper takes thick goal grains (less than 1.5 cm) as research object. According to different densities and particle sizes, thick goal grains are divided into 20 kinds of narrow density and narrow size level average grains. Free settling and hindered settling tests are respectively carried out in ?100 fluidised bed thick goal separators. Hindered settlement includes hindered settling velocity test and measurements of suspension density. Results show follows. (1) Fluid state in separator belongs to transition region. Alien's law is the appropriate formula of thick coal particles free settlement terminal velocity. (2) The main factors affecting hindered settling velocity are the number of solid particles in medium and the structure feature of the particle group. The bigger volume fractions of solids ? is, the smaller decreasing velocity coefficient of particle hindered settlement ¯ becomes. In the organism from bottom to top, density of suspended particles in fluidised bed gradually decreases, but near the top of the suspended particles, the density increased slightly. With increase of density and size, suspension density reducing extent increases from bottom to top of separators.

Sep 13, 2010

By H W. Wu

The objective of this paper is to examine some modern forms of auxiliary ventilation fabric ducting with streamline design fittings and the efficiency of construction practices. The most dynamic form of auxiliary ventilation is a moveable fan and ducting, which is easy to install and uses light weight fabric. The porous nature of some ducting construction results in leakage and loss of efficiency. Flexible fabric ducting is primarily associated with metalliferous mining and industrial material quarrying. Some applications are found in coal in stone/rock development and with use of dust scrubbers.Forcing auxiliary ventilation systems employing circular fabric ducting have been examined. Leakage of air from ducting is affected by ducting material and construction methodology (such as welded or sewn), quality of installation, number of joints, total length, pressure differences between the inside and outside and diameter. The best ducting system with welded construction can have up to four times less leakage as compared with some systems with sewn construction. It is also evident that the sewn type ducting will deliver less air to working faces and require more fan power, hence higher operating costs to run when connected to the same fan.A case study has also been undertaken to compare predicted operating costs of auxiliary ventilation systems connecting various types of ventilation duct fittings. The study also assesses the technical importance of streamline design with low aerodynamic resistance to reduce the shock losses of the duct fittings. It was found that the system connected with streamline designed fittings is able to provide some power cost savings and deliver more air compared with the system fitted with conventional fitting pieces.Using a ventilation ducting system with a lower leakage and frictional characteristic represents a sound solution to new challenges faced by the industry for increasing demand for better quantities and quality of air delivered to working faces; this is due to higher production schedules and stricter mine health and safety regulations within the Australian mining industry.CITATION:Wu, H W and Gillies, A D S, 2017. A comparison of auxiliary ventilation systems and their predicted operational performances, in Proceedings Australian Mine Vent Conference 2017, pp 207–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 28, 2017