Search Documents

By Elizma Ford, Vincent Sithole

"Two shortened test procedures for estimating the Bond ball work index are compared for suitability of use on Zambian/DRC-type copper–cobalt ores. The first procedure is based on a batch milling test while the second procedure is based on a limited locked-cycle test. Both procedures were conducted using a standard Bond test mill. INTRODUCTION The Bond ball work index is widely used in the field of minerals processing as an indicator of ore grindability. The work index is determined by means of a locked-cycle test procedure that typically requires seven to eight cycles to stabilise at a re-circulating load of 250%. A typical test requires between three to four kilogram of ore sample and around eight hours of operator time. For geometallurgical test work applications, where a large number of variability samples are to be tested, it would be highly beneficial to use a test procedure that requires less sample mass and operator time. Certain test work laboratories, for example SGS and JK Tech, are already offering various types of shortened test procedures for estimating the Bond ball work index. This paper discusses a comparison of two shortened test procedures that were evaluated for suitability of use on Zambian/DRC-type copper–cobalt ores. EXPERIMENTAL Test Procedure 1 – Batch Milling The first test procedure is derived from a batch milling approach proposed by the University of Hacettepe (Aksani, 2000). Some modifications were, however, made to the data analysis method from that originally proposed. During this test procedure, a 700 mL volume of sample is milled in a standard Bond test mill for a pre-determined number of revolutions. The feed and product particle size distributions are measured for each test. These results are then used to back-calculate a cumulative breakage rate parameter (k) for each particle size, according to the following formula:"

Jan 1, 2015

The objectives of this paper are to introduce the International Code of Practice for Risk Management of Tunnel Works and to illustrate to the participants of the 13th Australian Tunnelling Conference 2008 how the insurance industry would like to see the future of tunnelling insurance. Tunnel construction projects have suffered large losses over the years as can be shown from various loss examples and a list of major losses over the last ten to 15 years. Since the consequences of insufficient risk control had to be borne by insurers, these losses have heightened the need for improved and adequate risk management measures so that insurance cover can also in future be provided for this hazardous industry sector. Observations are made as regards to the prevailing trends in the tunnelling industry, which contribute to the increase in risk and have adverse consequences for the insurance industry. To find a solution to this dilemma various options are examined with the suggestion of a Joint Code of Practice for Tunnel Works being agreed by all stakeholders, which would become essential to secure future insurance protection for such project work. The British Tunnelling Society has, in cooperation with the Association of British Insurers, developed such a code, which the International Tunnelling Insurance Group has now adopted for global application in international markets. The content and concept of this code is explained to establish a framework of understanding and applied risk management principles for tunnel works. This initiative also has the support of the International Tunnelling Association and the International Association of Engineering Insurers. The international application of this new code is demonstrated with a few examples, which also includes Australian projects. It is the aim that this code forms in future part of the insurance coverage for tunnelling works in order to put this risk segment on a more sustainable basis. For that reason the insurance industry is seeking the support of all stakeholders of tunnelling construction projects.

Jan 1, 2008

By E. W. Thorton

"This paper is intended to show that grinding media can effect flotation results, and in some instances the results are vastly different. I do not suggest that autogenous grinding is beneficial in the separation of all complex base metal ores, in fact I know of a case where autogenous grinding would be disastrous to any selective flotation. I do however contend that prospective flow sheets and reagent balances of any complex base metal ores should be tried with both types of grinding. I feel fortunate that the paper to be presented later in this meeting by Rene Klymouski will, I think, compliment and perhaps explain some of the results of my research.This paper will be in four parts. The first part deals with a literature survey on the subject. Surprisingly enough, very little information has been printed on the subject. The second part deals with results obtained in bench scale tests on an ore from Chester Mines Limited. It was in these tests that we realized that steel grinding was giving us serious problems. So bench scale tests are shown giving results with a stainless steel grind, a mild steel grind and a grind in a ceramic mill with ceramic billets.The third part of the paper deals with results obtained in the Mines Branch Pilot Plant, when again we ground the ore with three different types of grinding media. Incidentally, this has been the only pilot plant test made at the Mines Branch in which flotation products were made on both steel grinding and autogenous grinding on the same ore. The fourth part deals with two other New Brunswick ores and is intended to show that changing the grinding media effects ores other than that of Chester Mines Limited."

Jan 1, 1973

By W. Bryszewski

As a result of strategic analysis in respect of the needs for air quality management a new advanced and holistic approach to air quality management process was introduced in the North West Province (NWP) of South Africa. The process is based on the principle of co-operative management. It involves both active participation of all Interested and Affected Parties (I&AP) and the holistic approach to solving problems with the underlying principles of shared ownership and sustainable development. The process consists of the followings phases: ? Industrial process quantification ? Quantification of impacts ? Formulation of the required control measures ? Definitions of certificate conditions ? Implementation of an adequate compliance management system at company level ? Ongoing co-operative air quality and system management with the strategic objective of continuous improvements The system has been successfully introduced in the North Province and proved to be an effective management tool and aids assurance of sustained environmental ability to cope with the pressure of industrial developments. The benefits and effectiveness are discussed using Hernic Ferrochrome as an example. Hernic Ferrochrome is one of the first companies, which successfully implemented this system.

Jan 1, 2004

By Yunyan Wang

Diagrams of pc-pH for the complex ions concentration and pH value and -g- for activity coefficient and ionic strength ln±MnSOI4had been drew based on the thermodynamic principle of coordination chemistry and combined with Pitzer theory at 298.15K. The diagram of -g- indicated that -gincreased sharply from 0.0000 up to 1.2147 when I changed from 0.00 ln±MnSOIln4±MnSO4to 0.09; The increase of -gbecame slowly when I was more than 1.00 and less than 1.69; kept still when I ln±MnSOln4-g±MnSO4was more than 2.25 and less than 4.00. Diagrams of pc-pH illustrated that the minimum solubility of Mn(OH)2(s) increased with the increase of I, the pc increased from 6.5 to 5.5 when I increased from 0.00 to 4.00; The pH of the minimum solubility of Mn(OH)2(s) increased with the increase of I, the pH increased from 11.80 to 12.76 when I increased from 0.00 to 2.89, the pH kept still when I (I was less than 4.0) increased. There is single function relationship between the minimum solubility of Mn(OH)2(s) and relevant pH in different I.

Jan 1, 2010

By Austin E. Dwight

IT has been shown by Oelsen and Wever' that the effect of a solute element on the allotropic transformation in iron is dependent upon the quantity

Jan 1, 1957

By Youngtak Ko, Wonnyon Kim

Korean contract Mn-nodule field in the NE equatorial Pacific is composed of seven sectors showing average water depths of 4,513 - 5,025 m. Of the various factors controlling the property of Mn-nodules, water depth has a potential linkage to chemical composition, shape and abundance of nodules. To clarify such a possibility, we review more than 20 years of research data in one of the northern sectors (hereafter KR1) where there is a marked contrast in water depth. High-resolution seabed mapping clearly separates a northern part from a deeper southern part, cutting across the middle of the KR1. In terms of nodule occurrence, manganese nodules in the deeper north are comparatively larger (2-4 cm) with rough surface (t-type) and discoidal shape (D-type), while those in the south are generally small (<2 cm) with smooth surface (s-type) and irregular shape (Itype). In addition, the nodules in the north have higher metal contents including Cu, Mn and Ni. Such connections of water depths to nodule occurrence and metal contents are commonly observed in the Korea licensed Pacific nodule fields. However, the relation between nodule abundance, size and water depth may be a different story. In KR1, nodule abundance and size are probably controlled by morphological features especially in the north. Seamounts in the north continuously provide rock fragments as new nuclei for the nodules. As a result, the nodules can not grow larger than 2 cm and show the shapes of newly formed nodules (i.e., smooth surface and irregular shapes). Such an interpretation is supported by anomalously high backscattered intensities in the side-scan sonar image map of the north, which possibly reflects a younger generation of magmatic activity.

Sep 1, 2014

By R. Unger, L. Mallett

The use of virtual reality (VR) technologies to train miners is an evolving area in research and development. In July 2006, representatives of 14 international organizations met to discuss current VR-related efforts and explore ways to employ VR in the future. This paper gives an overview of the various approaches presented at the meeting and discusses directions for future implementation. An example of a training package that teaches mine map-reading skills is presented. The meeting was the first step to building collaborations for furthering VR applications for mining. Planning has begun for a 2008 meeting open to broader participation.

Jan 1, 2007

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof&apos; stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division&apos;s deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By V. Kecojevic

Environmental and economic costs related to equipment fuel consumption and carbon dioxide (CO2) emission present a substantial challenge to the mining industry. Haul trucks are an integral part of the overall surface mining system and they consume a substantial quantity of fuel. Consequently, they produce a significant amount of CO2. The objective of this research is to (i) establish a mathematical relationship among a truck?s fuel consumption, power and engine load factors and (ii) determine the amount of a truck?s CO2 emission and the associated cost that may arise from potential CO2 legislation. In order to achieve these objectives we have considered original equipment manufacturer (OEM) haul trucks, commonly used in surface mining operations. The research presented here may be used by mining professionals to help determine the cost and environmental burden of the trucks? application, and efficiently manage energy consumption.

Jan 1, 2011

DURING September, the Coal Commission pre- pared for issue a series of 18 reports on varied aspects of- the bituminous coal industry; the final report, dated Sept. 22, sums up the facts and offers recommendations addressed to Congress, to the industry, and to the public. The few following paragraphs are selected: Bituminous coal is the real foundation of that great industrial and transportation structure which enables more than a hundred million people to live in America and be so well supplied with things necessary for their health, comfort; and convenience; it also furnishes domestic fuel for two-thirds of the homes of the land. The distribution of the output of the bituminous mines tells the story: 28 per cent. goes to the railroads, 25 per cent. to the boiler houses of factories and mills of all kinds, 15 per cent. to the coke ovens and gas plants, 10 per cent, to the homes, 7 per cent. to steel plants and the same percentage to power plants and street railways, 4 per cent. is exported, 2 per cent is used for power at the coal mines, and the remaining 2 per cent. goes to the seaboard for steamship fuel. Bituminous coal enters into interstate commerce on a scale approached by no other commodity; less than a fourth of the coal mined in the United States fails to enter interstate com-merce. All but one of the 45 coal producing districts in the United States ship coal outside the State in which it is mined. Three hundred miles of cars loaded with coal is the daily output of the bituminous mines of the United States. The public-welfare element in coal is seen in the dependence of public health and safety on an unfailing supply of fuel, in the close connection between the prosperity of most industries and the uninterrupted operation of the coal mines, and in the obvious fact that without coal the great network of railroads which binds together this great country would be idle. The railroads and the public utilities, themselves so clearly obligated to render what-ever public service is demanded of them that the constitutionality of their public regulation is unquestioned, are of all industries most dependent upon coal. Thus, coal makes up over 35 per cent. of the operating cost at the gas plant and over 25 per cent. at the electric power station, and in the operating expenses of. a railroad the cost of coal is the largest single item, next to labor. The practical logic that half a century ago clothed with a public interest the steam locomotive and in later years the electric-power station must recognize a large element of public service in the coal mine that furnishes the necessary energy to both locomotive and power-plant.

Jan 10, 1923

By E. A. Gulbransen, J. W. Hickman

DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may Occur to such a degree that oxides may form in the body Of the film and On the outer surface which are different from those that would normally form if the additional elements were not present. The use Of transmisson electron diffraction may aid us in jnterpreting these phenomena. UP to the Present time all Of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physica1 state of the "alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the remova1 of carbon by Oxygen in a decar-burization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with lifetime tests carried

Jan 1, 1949

By P. R. Richardson

"Milling is the weak link in the process chain of many mineral operations. While this activity accounts for only a relatively small proportion of the direct costs of most mineral processing complexes, there are intangible and indirect costs associated with milling which are extremely large. For example, significant opportunity costs are associated with the relatively low yields which characterize this stage of the process.There are changes abroad in the world which I believe are going to cause us to reformulate the whole concept of milling. Increased competition in mineral markets are going to force managers to look anew at the high mineral values reporting to tailings which are a high opportunity cost for many operations. Tailings recovery plants are not the ultimate solution to this problem. Greater environmental concerns are going to increase the costs associated with tailings disposal and force the mining industry to look for other ways to dispose of waste products. Technology changes currently underway in manufacturing and other process industries, such as the automated 'lights-out' plant are going to be brought into this industry, and the changes will be dramatic.These are major long term changes which probably seem rather remote to many managers and professionals in existing operations which are faced with much more mundane challenges arising from day-to-day operations. However, I believe that milling is increasingly a 'lean and keen' operation involving fewer and fewer people, but who are increasingly skilled and professional. Traditional cost management approaches are no longer adequate and the industry has to take a new look at the nature of cost reduction in this core activity. This stage in the mineral process provides opportunities for value creation leading to a significant unit cost advantage for the corporations willing to adopt a total cost approach."

Jan 1, 1988

By Werner Burger

The last decade has witnessed a rapid development and application of slurry and EPB type tunnel boring machines. Both soft ground types are able to excavate tunnels in unstable ground conditions below the water table with positive face support. The most significant component of the excavation process is the cutterhead and tool con-figuration were the excavation and face support meets the geological challenge. The TBM downstream processes cannot take place unless the cutterhead and tools effectively do their job. This paper will review the current state of the art design for both slurry and EPB cutterheads and highlight both common as well as geological specific design features.

Jan 1, 2007

By D. R. Babich, E. R. Bauer

National Institute for Occupational Safety and Health (NIOSH) researchers are conducting a cross-sectional survey of equipment noise and worker noise exposures in the mining industry. Surface and underground limestone is one commodity recently surveyed. The sound levels of mining and processing equipment were recorded to identify noise sources. Full-shift worker noise exposures were completed to determine the exposure of various occupations. This paper presents the results of the noise research conducted in both underground and surface limestone mines, detailing the equipment likely to cause worker overexposures, and the occupations experiencing overexposures. Implications for worker noise exposure reduction are also reported.

æSustainabilityÆ is one of those words that has gained more usage in popular discourse than in the dictionary. In fact it is not in many dictionaries at all. Typically, given this, it also seems to mean different things depending on whose lips it emerges from. It is now like a code word in that if people say it, you donÆt have to think about its meaning; it is just æthereÆ and is taken for granted. This is a problem for the mining industry as we are now using the term too and to be effective in what we do, we need to have a reality check and see how those outside who have views on us (æstakeholdersÆ maybe) use it. The core issue seems to be æsustainability of whatÆ: the industry?, a company?, the global environment?, particular ecosystems?, the community? At these levels, the term seems almost meaningless. If we do not even agree on what it is, at least broadly, our communication and possible partnerships for going forward will be difficult to say the least. One reference to æsustainÆ in my thesaurus is: æTo keep from failing during stress or difficultyÆ. This may be a clue to something approaching a common notion. I suggest that to use æsustainabilityÆ we make the following assumptions:that we are talking about human activity aimed at making a living that has an impact on the natural and social environment; that humans must make a living (though what this needs to include is problematic); that the impact of particular activities has been problematic to date and needs to be monitored, altered, stopped, etc; that there is stress on both social and natural environments; and that change can be effected in order that particular activities such as mining minimise their negative effects and maximise their positive. This is why we are taking part in sessions such as this one today. Two more initial observations: First, it strikes me that even with the above assumptions laid out, æsustainabilityÆ and æsustainable developmentÆ are too abstract and general as concepts. We have to break these high and mighty ideals down into workable, bite-size chunks, into practical ways of dealing with the world outside our sites and companies. Second, sustainability, on both sides of the fence, too often focuses on nature and environment as though they are independent of people and community. I would argue, perhaps provocatively, that sustainability is primarily a people issue and has to be tackled as such. I want to look at the overall climate for business today and how it has responded before I return to what we can and need to do as the mining industry to make æsustainabilityÆwork.

Jan 1, 2002

By Robert A. Harrow

This report documents the results of the development and installation of an illumination system for an underground coal mine Shortwall Mining Section. Also presented are the techniques used for the above ground test and evaluation of the lighting system prior to installation underground which resulted in the issuance of a Statement of Test and Evaluation (STE) from the Mine Safety and Health Administration, Technical Support, Beckley, West Virginia.

Jan 1, 1979

By C. McCall, J. T. Knight, J. R. Ridley

Gold mineralisation in the gabbro sills is mainly stratabound to quartz- and Fe-rich, granophyric-textured units and is sited in undeformed, brittle quartz vein sets, which form pipe-like orebodies. Hydrothermal wallrock alteration consists of hornblende-plagioclase-calcite-quartz with minor biotite, garnet and chlorite and with arsenopyrite and pyrrhotite as the dominant sulphides. Geothermobarometric data suggest that gold was deposited at around 520 degrees C at 2.8-3.8 bar. Mineralisation is thought to have occurred during amphibolite-facies metamorphism. Fluid inclusion and isotope data indicate that gold mineralisation was the result of deposition from a low-salinity H2O-CO2-CH4 fluid of either metamorphic or magmatic origin. Although the Three Mile Hill deposit differs from others in the area in its wallrock-alteration assemblages, peak-metamorphic timing of gold deposition and distinct geochemical associations it forms a brittle stratabound ore body which suggests structural and gold-depositional mechanisms in common with those of the other gabbro-hosted gold deposits

Jun 18, 1905

By J. E. Rourke, O&apos

A wide variety of techniques and equipment are available for coring soft or poorly consolidated geological material. This report presents a comprehensive literature review and evaluation of these techniques and equipment. A potential user will find guidelines in this report to assist him in selecting sampling equipment. A bar chart shows what samplers have been used under what geological conditions, and gives the specific literature references. Two matrices rate the present techniques and equipment with respect to reported success for sampling specific materials, and with respect to several performance characteristics including complexity of use and core quality. These matrices are supplemented with tables of typical sampling equipment. and program costs. Near-term future developments are seen primarily in improved training of drillers, and in instrumenting the drilling operation to provide objective data on drilling characteristics. An extensive annotated bibliography, a catalogue of equipment suppliers including specifications and cost ranges, and a list of manufacturers and distributors are appended to the report.

Jan 1, 1978

By George A. Savanick

This paper reviews advances in the art of borehole (slurry) mining made by the Bureau of Mines from 1974 to 1980. The design of a proto-type borehole-mining tool (BMT) developed by the Bureau of Mines is pre-sented along with production data, reclamation data, and an application of the BMT to the mining of coal, uraniferous sandstone, oil sands, and phosphate ore. The BMT was first used near Wilkeson, WA, where steeply pitching metallurgical coal was mined at 8 st/h from a depth of 25 to 75 ft. Next, 940 st of uraniferous sandstone was mined at 8 st/h from a depth of 75 to 100 ft in Natrona County, WY. One thousand short tons of oil sands was mined in Kern County, CA, at the rate of 14 st/h from a depth of 110 to 150 ft in 1979. Most recently, 1,700 st of phosphate ore was produced at 25 st/h from deep (230-to 250-ft) deposits in St. Johns County, FL. Progressive improvements were made in the borehole mining technique. These include the use of the hydrostatic head of a water-filled borehole for roof support, and the development of methods to survey and backfill mined-out cavities.

Jan 1, 1987