Search Documents

According to the previous research, it is found that the thickness of cover is mostly less than 100 m for highwall mining system. However, for most of the Chinese surface coal mines, the mining depth is over 150 m; on the other hand, the shovel-truck is the most common mining technology. As a result, a lot of residual coal will be remained around end-walls. Considering these facts, the calculated methodology of highwall mining system under thick cover is presented in this paper. Meanwhile, numerical simulation of highwall mining system under thick cover was carried out. The outcome shows that the calculated methodology for pillar stability of highwall mining system under thick cover presented in this paper is acceptable. In other words, the highwall mining system is feasible to extract the residual coal around end-walls in Chinese surface coal mines. Thus, not only coal recovery ratio can be improved, but also can increase the production life of surface coal mines in China.

Jan 1, 2012

By Guy Chevalier, Jean-Guy Chartrand, Louis Barrette, Daniel Michaud, Michel Fortin

"COREM has developed, specifically for the mineral industry, a mobile laboratory using the Laser-Induced Breakdown Spectroscopy (LIBS) technique. It has been used to perform onstream analysis (OSA) of the chemical composition of slurries in both gold-ore and iron-ore processing plants. Industrial tests have been carried out respectively at La Mine Doyon (Cambior), a gold-ore processing plant near Rouyn-Noranda, Quebec, and at QCM's iron-ore pelletizing plant in Port-Cartier, Quebec. The aim was to demonstrate that the LIBS technique is capable of providing information that meets the needs for process control. C, Si, Ca, Mg, Mn and Al were the elements targeted on iron ore while Cu, Fe, Ag and Au were targeted for gold ore. The results obtained meet or exceed the requirements for process control and consequently clearly show that the LIBS technique is suitable for industrial applications.The feasibility of OSA, through in-plant validations using COREM’s LIBS mobile laboratory, has been demonstrated in four essential aspects: slurry sampling, LIBS chemical measurement, robustness for continuous operation, and functionality for industrial operators.INTRODUCTIONThere is a general need for optimization in the mineral industry. Process control is a favoured means to achieve this goal (McKee 1991). Real-time knowledge of process status is the key to effective control (Da Silva 1994). Only a few techniques, such as XRF, NMR and digital imaging, are currently amenable to chemically monitor industrial processes (Braden 2002). LIBS is an emerging technique with appealing characteristics for on-line and real-time measurement of bulk material (Lorenzen 1992, Palanco 2000). While our ultimate goal is to provide our industrial partners with performing monitoring tools, a shorter-viewed objective is to demonstrate the feasibility of developing a LIBS system for OSA. The LIBS technique has shown interesting capabilities for measuring solids, liquids, dusts and gases. Our work has focused on mineral slurries (Barrette 1999 and 2001, Turmel 1999). Special equipment is needed to perform in-plant validations. A mobile laboratory based on the LIBS technology has been assembled for this task."

Jan 1, 2004

By Steven Norris, William Moler, Michael Cole, Patrick Doig, Debi Lewis, Craig Pyle, Matthew Crow

The recently completed Lower Northwest Interceptor Program (LNWI) in Sacramento, California comprises, ten pairs of micro tunnels totaling 4,369 m (14,417 ft),three horizontal directionally drilled bores totaling 956 m (3,154 ft), and two large diameter tunnels under the Sacramento River totaling 1,198 m (3,953 ft). This paper briefly summarizes surface and subsurface conditions, and planning and design considerations. It then goes on to describe problems encounterd with each trenchless crossing, as well as lessons learned with respect to shaft construction, ground control at shafts during tunnel break-in and break-out, frac-out and heave, settlement, obstructions, coordination with permitting agencies, and application of geotechnical baseline reports.

Jan 1, 2007

By Douglas Bartley, Brian Wingfield, Robert McClure

Recent studies and limited tests indicate favorable results utilizing high accuracy electronic detonator technology over conventional non-electric pyrotechnic systems. This study discusses the application of this technology using the Daveytronic programmable system in an on-going production basis. The study quantifies the performance as it relates to fragmentation, excavation, vibration and productivity in an eastern U.S. aggregate mining operation.

Jan 1, 2001

By D. Babich, L. Alcorn, E. Spencer, A. Smith

Noise is one of the most pervasive health hazards in mining. A compilation of Mine Safety and Health Administration (MSHA) noise survey data for Fiscal year 1990 shows that approximately 40% of the total samples taken for longwall occupations exceeded the Permissible Exposure Limit (PEL) of 100% [Gigliotti et al. 1991]. In order to properly determine workers’ exposures on longwall coal mining systems, it is necessary to provide accurate baseline measurements for these mining systems. This research was designed to develop guidelines and test procedures for identifying all noise sources that are major contributors to the underground noise exposure of longwall coal mining system workers. Once the high noise sources are identified, promising engineering controls can be tested and evaluated to reduce the noise of the sources. The measurement system used to analyze the noise sources included stationary dosimeters in a documented repeatable pattern and a time-motion study of the cutting cycle and operator’s work cycle. Significant results from the underground measurements show that the highest sound levels recorded are at the stageloader discharge segment and tailpiece controls and remained at about the same level throughout the test.

Jan 1, 2007

By P. Gonzalez, C. Ariyo, L. Holappa

Oxidation state of titanium was determined in CaO-SiO2-TiOxslags in the composition range25–53 per cent CaO, 27–46 per cent SiO2, 10–55 per cent TiOxat 1873K using gas equilibration method. In the experiments, slags with different titanium oxide contents were equilibrated with a known carbon monoxide and carbon dioxide ratio. The results were used to determine the Ti3+and Ti4+contents as well as the activity coefficient ratio of corresponding oxides in the slag. The dependency of the activity coefficient ratio as a function of oxygen partial pressure was determined. Keywords: titanium, titanium oxide, activity, activity coefficient, slag iron, carbon monoxide,carbon doixide, gas, equilibrium.

Jan 1, 2004

By Éric Poulin, Simon Gariépy, Mario Paredes Malca

"While the design of a control strategy depends on the available process knowledge, its implementation depends on the available process information. On-line chemical analyzers are today widely spread in the mineral processing industry. A real-time concentration measurement of chemical components is valuable information that could bring control strategies to whole new levels. However, the use of these measures rarely reaches anything more than process monitoring. The reason is simple: the on-line chemical measurements quality is most of the time insufficient to be directly included in control strategies. The choice is then made to let the critical eye of the engineer or the operator appreciates the measurements before making any decision based on it.Data reconciliation through mass balance is a technique today widely used in the mineral processing industry to increase the accuracy and the reliability of plant data, mainly for accounting and survey analysis purposes. Real-time data reconciliation of on-line measurements appears as a natural coupling of technologies that could bring new process optimization trends. Once overcome the technical difficulties, full valorization of the instrumentation investment could be reached.This paper presents the application of real-time data reconciliation for process control and performance monitoring. It proposes a general approach, discusses challenges and illustrates concepts with industry experiences."

Jan 1, 2006

By N. T. Lowe

The National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory (SRL), investigated a means to evaluate the potential impact of surface conditions above underground mines on emergency response activities. Recent events have highlighted the need to conduct critical emergency operations on the surface above underground work areas. Accessibility and usability of the surface, such as the ability to drill holes or deploy seismic monitoring or through the earth communications systems, are an important consideration for emergency response planning. This paper identifies critical surface conditions such as: surface waters, valley fill, highways, railroads and significant structures that must be considered in emergency response planning and in the conduct of emergency operations as they relate specifically to the seismic detection of trapped underground miners. Results of case studies indicate a need to consider the impact surface conditions may have on emergency response capabilities.

Jan 1, 2009

By W. Burger

In underground mines worldwide, a large number of short and small diameter slot holes need to be excavated. Herrenknecht has developed and built a new boxholeboring machine based on the well-proven Microtunnellingpipe jacking technology. The innovative Boxhole Boring Machine significantly increases work safety and requires only minimal drift dimensions. The high and consistent production rates that can be achieved result in enormous time savings compared to conventional drill and blast excavations. GENERAL ASPECTS In gold, copper and ore mines ventilation shafts are required to prepare block caving operations, to discharge ore onto the transportation level and to provide evacuation shafts. A high level of occupational safety and efficiency is the main objective when drilling vertical or inclined shafts. The faster and more safely shafts can be constructed, the earlier the actual production in the mine can start or be continued. Mechanized or conventional methods (drill&blast) that have been used to date only partially meet the required safety standards and fail to provide the requested production rates.

Jan 1, 2012

By R. Dippenaar

The emergence of new steel grades is largely driven by the need to produce high quality steel at a competitive price. The principal aims are to attain ultra-high purity, (especially low interstitial elements) and ultra-cleanliness (by the control of the inclusion content and size). Whereas the steel used to build the Titanic contained 650 ppm sulphur, resulting in MnS stringer-inclusions 25 mm in length, modern quality requirements for arctic pipelines would only allow 10 ppm of sulphur and inclusions in ball-bearing steels must be smaller than 5µm. Most developments are aimed at hot-metal treatment before refining and ladle treatment after decarburisation. Because ferroalloys are added during or after the refining step, it is the secondary (ladle) refining production technologies that are of specific interest to the ferroalloy producer. Through ladle treatment, hydrogen and nitrogen contents are reduced, ultra-low levels of solute impurities are attained and the shapes as well as the composition of inclusions are modified. Steelmakers are concerned about the cost effectiveness of the use of ferroalloys such as consistent product analysis and delivery, improved financing arrangements and technical support. Minimal variation in product sizing is vital because it impacts on handling problems and because particle size determines the rate of particle dissolution. The required ferroalloy product quality depends on the specific use but in general sulphur, phosphorous and nitrogen contents are of concern. Apart from the presence of trace and impurity elements, ferroalloys also contain inclusions. For example, ferromanganese may contain MnO-MnS-SiO2 inclusions while high-carbon ferro-chrome may contain different kinds of Cr-Mn-spinels. The presence of these impurities and inclusions has a significant impact on steel production techniques and cost and hence, on the selection and use of ferroalloys. The interrelationship between ferroalloy quality and steel production technology is plant and product specific and hence, effective communication between ferroalloy suppliers and steel producers is essential.

Jan 1, 2004

By L. Andrews

Nickel is recovered as a by-product of the platinum-producing process operated by Anglo Platinum. The metal is mined mainly as sulphide minerals contained in platinum ores. These pass through the concentrating, smelting and converting process route and nickel is finally recovered by electrowinning. Smelting of the concentrated ore in the electric furnace produces a melt with a high slag to matte ratio. The resulting furnace slag is granulated and later milled and floated to recover matte. A project was initiated to investigate the distribution of nickel in the slag in order to improve recovery. Slag samples were examined using a combination of chemical and mineralogical techniques. The granulated slag was found to consist mainly of a silicate glass phase, which reflects the composition of the molten slag in the furnace. Nickel occurs as free matte granules, as matte phases locked inside the glass, and in the glass phase itself. Whereas nickel in the matte is as sulphide, most of the nickel in the glass phase appears to be oxide- bound(i.e. in solid solution). Milled slag as flotation feed showed recovery-limiting features such as free matte with oxidized surfaces and unliberated matte inclusions in the slag. The biggest nickel losses, assuming no tapping problems, are in the glass phase solid solution. Only around 40% of nickel would be recovered from the slag, even under ideal conditions. Spoon and pot slag samples were also examined to see if casting and crushing would improve recovery. Although larger and therefore more easily recovered matte phases formed, nickel partitioned into crystalline silicate phases, limiting the maximum theoretical nickel recovery to 70%.

Jan 1, 2004

By A. J. Rigby

Refractory linings in converters or anode furnaces used to over-oxidize the blister copper will suffer rapid deterioration, due to prolonged contact with copper oxide-rich slag. Nitrogen stirring with COP KIN porous plugs and use of SEMTECH OPC in converters and anode refining vessels can considerably reduce both refractory wear and processing times. In addition, careful control of the vessel atmosphere and the use of real-time optical process control minimize both slag volume and contact time with the vessel refractory.

Jan 1, 2005

By J. Nielen van der Merwe

Rock engineering research and technology development in South Africa only received serious attention in reaction to the Coalbrook disaster in 1960. At the time, a number of gaps in knowledge of rock related matters were identified and in the ensuing years, these were progressively attended to. The paper describes the events that led up to the Coalbrook disaster and reviews the developments that took place afterwards. The effectiveness of the research outcomes are tested by referring back to the disaster. It is concluded that tremendous advances were made but that not all the unknowns were attended to at the same level. The strength of nominally square internal pillars is the one issue that received the most attention, but the strength of barrier pillars, overburden behaviour and loading systems are still largely unknown. Due to the complexity of the remaining unknowns, they can and should be addressed by the application of back calibrated numerical models. There are no readily available simple analytical solutions. The state of mining rock engineering research in South Africa borders on an emergency. More than a 1000 years of aggregate research experience has been lost in the last three years and funding is under severe pressure. There are disturbing parallels between the current positioning of the industry as a whole and the Coalbrook mine in the years preceding the disaster.

Jan 1, 2006

I HAVE to thank the members of the Institute most cordially for the honour conferred upon me in selecting me President, which position my poor services have prevented my filling adequately. I have, therefore only been able to stumble through my year of office under the guiding direction of our esteemed Secretary. I fully appreciate the honour done to me; and, now that it is over, I can look back with pride and pleasure at having occupied the chair; but I am told that it remains for me to fill one of the requirements of our Institute and present you with what has been dignified by the name of a presidential address. My relief in complying with this is in the knowledge of its freedom from the usual discussion which appertains to papers presented by our worthy members. It has been usual in the past for the subject chosen to be specially connected with the work immediately engaging the attention of your president, and on this occasion I would like to break away from this time-honoured custom and engage your attention for a brief space on what is equally dear to us all namely, Ideals of the Profession. In doing so, the retort of Whistler to an art student gives me, I must admit, much misgiving, for, on being asked how he developed his artistic talents, replied that he painted what he saw, which produced the immediate reply, "Ah, but the tragedy will come when you see what...

Jan 1, 1909

By Jessica Egan, Daniel Hodouin, Claude Bazin

"The recovery of gold by leaching is influenced by the size of the gold carrier particles and the chemical environment. Using the relationships between the leaching rate, infinite recovery and particle size for a given set of chemical conditions, it is possible to simulate gold recovery for various feed size distributions. However the use of these particle size relationships is only valid if the leaching of gold from a given size class is independent of the production history of this size class. For instance, to use these relationships it is necessary to verify that gold recovery from the leaching of the 200-270 mesh size class remains the same if the size fraction is taken from a coarse or finely ground ore sample. Several laboratory tests were carried out to answer that question. Results of the tests show that within the large error margin associated to gold content measurements, the history of the production of a size class does not affect the gold leaching from that size class. Emphasis of the discussion is put on the difficulty associated with the processing of data containing significant measurement errors as it is the case for gold assays of leaching tests.INTRODUCTIONMore than 75% of the gold produced in the world is extracted by cyanide leaching of gold ores. The ore is ground to expose the gold carriers and the ground material is reacted in an oxygenated cyanide solution that dissolves gold, leaving solids gangue minerals that are disposed to tailings ponds or returned in underground mines as paste fill. The gold contained in the solution is recovered by either the carbon in pulp process or by cementation onto zinc powder, before being melted and casted into a brick (Marsden and House, 2006)."

Jan 1, 2009

By Augustine O. Orumwense, Micheline Boisclair

"The use of stirred mill to complement tumbling mills in grinding fine grained minerals is increasingly becoming an attractive processing option. Parameters such as agitation speed, grinding media type and size, feed pulp density, and grinding time were studied in order to elucidate their impact on stirred milling. Test results showed that the parameters have a profound effect on stirred mill efficiency and operating cost. A comparative test with a tumbling ball mill was also made and the specific energies of both mills in fine grinding were analyzed. A difference of over 40% in energy savings particularly when the product size is smaller than 20 µm was obtained with the stirred mill.INTRODUCTIONIn industrial processes where very fine and ultrafine particles are required such as in chemical, ink, food, paint and lacquer, pulp and paper, plastics, pharmaceutical, metallurgical and ceramic industries, the use of stirred mills for grinding is well established. Mineral processing plants are gradually shifting focus to the use of stirred mills for fine grinding and /or regrinding purposes as the target liberation size gets very small. A number of plants processing finely/sparsely disseminated ores are known to have adopted stirred milling technology for their fine grinding needs (Enderle et al., 1997; Harbort et al., 1999; Gao et al., 2000; Davey, 2003 & 2006; Pease et al., 2006).There are different kinds/designs of stirred mills available on the market but, all can be divided into two sub groups namely fluidized and non-fluidized types. The non-fluidized stirred mills consist of Tower mill, Vertimill, Sala agitated mill (SAM), and ANI-Metprotech (SVM). These mills are characterized by their low-speed and the use of fairly coarse grinding media size, 3 – 20 mm. Hence, they are mostly suitable for relatively coarse grinding application. The fluidized type includes the Isamill, Netzsch mill and Stirred mill detritor (SMD). These mills have a characteristic high agitator speed, use fine grinding media size of 0.5 – 5 mm, and are employed in very fine grinding operations. The superior fine grinding capability of stirred mills is attributable to two main process parameters, which are the use of fine grinding media and a high mill speed."

Jan 1, 2008

By Ernie Doell, Trung Nguyen

"In early 1995 Cluff Mining commissioned a newly constructed high density tailings thickener at its Cluff Lake uranium mill. The 85 ft diameter high density thickener is one of the first of its kind in North America, and incorporates the novel paste technology in its design to produce densified (in the range of 60 -65% solids) mill tailings suitable for stable deposition in the tailings management area. This paper discusses the impetus behind the installation of such an unconventional thickener, and the many trying experiences in making it operational.IntroductionCluff Mining, a wholly owned subsidiary of Cogema Resources Inc., is the operator of a uranium mine and mill complex at Cluff Lake which is located in northern Saskatchewan. Since 1980, the company has developed and mined out several different ore bodies within the Cluff Lake region for the production of uranium concentrates, commonly known as yellow cake. Based on the known ore reserves, the Cluff Lake operations are projected to last till the early 2000's.Tailings from the Cluff Lake mill have been discharged to a tailings management area consisting of a tailings pond and two facilities for primary and secondary treatment systems. The tailings pond has an impervious bentonite lined dam, and it is divided into a solids and a liquids holding areas. Until the beginning of 1995, the mill tailings were discharged in two separate lines to the solids pond; one line carried the slurry residue of 45-50% solids (w/w) from the CCD circuit, and the other discharged raffinate tails containing less than 1 % (w/w) gypsum precipitate. Supernatant in the solids pond is treated in the primary treatment system prior to discharging to the liquids pond. Figure 1 shows the site plan of Cluff Lake tailings management area.It has been estimated that by the end of 1995 the solids pond would be filled to about 60% of its design capacity, and probably would be full before the year 2000. Therefore, Cluff Mining had to consider a more efficient tailings disposal method that could extend the service life of the existing Cluff Lake tailings management area. A high density tailings thickener was believed to be the most practical and economical system for tailings disposal at Cluff Lake mine."

Jan 1, 1996

By K. Grubaugh

Ghana’s physiographic and geologic features are the basis for its long mining history. The Gold Coast colony has been a significant producer of gold. The gold of the Akan forest (Ghana) was a terminus for caravans that plied Saharan trade routes. Now it also produces significant quantities of manganese, bauxite, and diamonds In addition, the country produces kaolinite, silica for glass, salt, and both aggregate and dimensioned stone. Most secondary minerals are consumed locally but some amounts do find international markets. Ghana revised the mining laws and regulations in 1986. These revised laws dramatically increased gold production and improved the country’s economy. The success of these laws spawned imitators in other African states such as Cote d’Ivoire, Mali, and Burkina Faso. Representatives of these countries claim Ghana was their model. Environmental regulations exist but an intensive adversarial atmosphere is lacking. Ghana has also offered the mining industry incentives like accelerated depreciation rates and exemption from import duties on related supplies and capital equipment. The country has also pursued an aggressive policy to restore the nation’s business infrastructure.

Jan 1, 2001

By J. E. Nesset

"I had been requested earlier this year by MetSoc, our sister society of CIM, to contribute a chapter on technical developments in Canadian mineral processing over the past 50 years to their 50th Anniversary volume. Accepting the challenge of assembling such a chapter seemed at first a reasonably straightforward task, until one realises that the list of contributions by Canadians to mineral processing over this period has been more than just significant. It turns out to have been an extraordinarily fertile time for innovation and impact for Canadian-based technology. The list is necessarily a subjective one, however I had no trouble identifying twenty technology developments that are clearly outstanding, and there are undoubtedly others. As much as possible, I approached the individuals themselves who played key roles in each technology and asked that they tell the “story”. Without exception, all who were invited accepted eagerly and delivered more than I had hoped for. The technologies have been grouped into those that are truly Canadian innovations, such as the Knelson gravity concentrator and the McGill gas dispersion sensors in flotation, and technologies where Canadians and Canada played a very significant role in their success and implementation, such as AG/SAG grinding and ion-beam surface analysis. Also included are what may be termed technology transfer initiatives and institutions that have risen to a world class level, such as SGS Lakefield and the Canadian Mineral Processors Society of CIM. The challenge is now for the coming generation to continue this record of innovation and contribution to the industry, and that includes the (mostly) Canadian mining and metallurgical companies who have taken the longer term view and supported many of these initiatives, through their critical early years, with both financing and project sites for these ideas. Let us hope that the current trend of mining company globalization will not dampen their enthusiasm to participate. This plenary presentation will highlight many of these technologies, the individuals behind them, and their significance to the mineral processing industry."

Jan 1, 2012

By Charles "Chick" Rodgers

"The Key Lake uranium mine is the largest single uranium producer in the world. It is owned 2/3 by Cameco Corporation and 1/3 by Uranerz Exploration and Mining. Cameco is the operator. Current production is fourteen million pounds per year of uranium oxide (U308).The mine's location is 570 kilometres north of Saskatoon on the southern edge of the Athabasca Basin approximately at latitude 57° 11 'north and longitude 105° 34' west. Access to the mine is by an all-weather road and a private airstrip.The mill was commissioned in 1983. A molybdenum plant was constructed in 1989 in response to increasing molybdenum content in the yellowcake or final product. Early test work had showed that the first ore body to be mined, the Gaertner deposit, would present few problems with regards to molybdenum in the product. However, the test work also showed that the higher molybdenum content of the Deilmann ore, the second Key Lake orebody to be mined, would result in increased molybdenum concentrations. Without the molybdenum plant, penalties would become excessive and some product might not accepted by the refineries.This paper will describe the current Key Lake mill process with emphasis on the molybdenum solvent extraction process. It will cover the chemistry of the process, process development in the mid 1980's, and current operating practices.The Key Lake milling process consists of five individual plants, crushing and grinding, leaching -counter current decantation (CCD), solvent extraction, yellowcake/crystallization and bulk neutralization (Figure 1. Simplified Mill Flowsheet). A detailed mill flowsheet can be found in the appendix."

Jan 1, 1996