Search Documents

By Clyde L. Brown

The ignition source of fires and explosions in coal mines is sometimes difficult to explain because resulting widespread destruction often erases valuable evidence that might reveal the cause. However, through years of experience, investigators have been able to piece together enough evidence to establish the reasons and, thereby, have been equipped to recommend corrective or preventative measures. The pattern of hazards is not constant. It changes with the development of new practices and new equipment. Important among the new hazards to coal mining are those introduced by electricity. In addition to the dangers of electric shock, fires and explosions from heat and arcs, and premature blasts, certain others have developed as a result of stray electric currents from direct-current traction systems. The conventional direct-current power-distribution system in coal mines is conducive to electrolysis damage to mine tracks, metallic pipelines, grounded power conductors, and structures in a position to become conductors of stray currents. The voltage drop resulting from power demand on intentionally grounded power conductors and accidental grounds on insulated conductors are common sources of stray currents in coal mines. Uncontrolled electric cur-rents flowing through the earth and metallic structures can be a menace, and these contribute to the estimated $6,000,000,000 annual loss caused by corrosion. The purpose of this publication is to discuss some of the electrolysis hazards in the coal-mining industry and to outline corrective measures to alleviate them.

Jan 1, 1962

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, and control of anthracite-mine fires, it was observed that the carbon monoxide disappeared from a sealed fire area much more rapidly than could be explained on the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance: (1) That the carbon monoxide, was oxidized at temperatures below 150° C. by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C. carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By Frank G. Horino

This report presents a method of utilizing the Coulomb strength criteria for estimating the strength and stability of pillars and pit slopes containing planes of weakness. It is assumed that the Coulomb theory, as a special case of the Mohr envelope, is a satisfactory first approximation of failure in uniaxial compression or triaxial loading with low lateral loads. Accepting this assumption for brittle materials, an expression for the strength decrease of rock pillars containing a plane of weakness or fracture at any angle of orientation is derived. As few as six samples (three solid cores and three fractured cores at a failure-oriented angle) are required for testing uniaxially and triaxially to statistically determine the coefficients of friction and the shear strengths of both the solid rock and the fracture plane and the range of failure angles of the fracture plane. Interpretation of the data shows that the mean normal stress and maximum shear stress technique of analyzing the data is superior for solid core and that shear and normal stress values using angles of failure should be used for fractured specimens with failure-oriented angles. Plots of either the strength or strength ratios against fracture angles obtained from oriented drill core samples give a useful first approximation of strength decrease due to fracture. Using the same test conditions for both fractured and unfractured material increases the validity of the tests.

Jan 1, 1970

By W. Valderrama, D. G. Almond

Operation of large SAG mills requires a change in the conceptual approach to grinding processes. The traditional energy consumption criteria are now enhanced with new criteria derived from the mechanical dynamics of the mill load. This new approach demands instrumentation capable of providing accurate information about the load movement and the ratio of balls and ore inside the mill. This paper discusses two new performance enhancing tools available to meet these needs.

Jan 1, 2004

By A. J. Potgieter, C. Hill, A. Humpel, D. S. Magudulela, V. Scholtz, A. Coetzee

Keywords: Pyrometallurgy, long steel products, coke, sinter, blast furnace, steel plant Located in Northern KwaZulu Natal, Mittal Steel South Africa Newcastle works produces roughly 1.8 million tons per annum, supplying long steel products, locally and overseas. The great extent of local raw material availability and low conversion cost ensures that Mittal Steel South Africa is among the lowest cost, high quality producers of steel. MSSA Newcastle works can be subdivided into two main sections: The iron making side, comprising the coke ovens, sinter plant and blast furnace, and the steel making side, comprising the basic oxygen furnace, ladle furnace, continuous casters, and the medium, rod, and bar mills.

Jan 1, 2006

By M. Lu, E. Broch

Abstract: The formation and mechanism of rock cavern roof arches are studied and effects of rockbolts reinforcement are evaluated. It is concluded that a self-supported roof arch may be formed by the excavation. To stabilize such a roof arch, fully grouted rockbolts are effective. Tensioned cable anchors may have a negative influence on the arch stability. Zusammenfassung: Die Formation und der Mechanismus von Deckenbögen in Bergkavernen wird studiert und der Effekt von Verstärkung mit Bergbolzen wird bewertet. Es wird festgestellt, dass die Exkavation einen selbst-stützenden / freitragenden Deckenbogen formen kann. Eingegossene Bergbolzen sind effektiv um einen solchen Deckenbogen zu stabilisieren. Spannkabel können unter Umständen eine negative Einwirkung auf die Stabilität des Bogens haben. Résumé: Le mécanisme et la formation de voûtes dans les cavernes rocheures sont étudiés et l'effet du renforcement par boulonnage est évalué. Nous arrivons à la conclusion qu'une voûte autosupportêe peut être formée par excavation. Des boulons entièrement scellés par coulis de bêton s'avèrent efficaces pour stabiliser de telles voûtes. Les tirants d'ancrage peuvent quant à eux nuire à la stabilité de la voûte.

Jan 1, 2003

By Ann Barron, Mark Abernethy

Along with the immense benefit of modern explosives seismic and acoustic effects caused by their detonation can be disruptive and alarming to many people. Claims range from affecting sexual performance to outright demolition of a residential structure. Regardless of the quality of the blast design and other precautionary measures, the inherent danger posed by the use of explosives often leaves residents searching for restitution. Consequently, many blasting companies today find themselves at the center of litigation. In the event that a blasting complaint proceeds to litigation your case will not be decided on “reasonable doubt” as in criminal trials. Instead, the jury will be instructed to decide guilt or innocence on a “preponderance of the evidence” presented. Even if you are able to present the best and most complete evidence that you have not caused the claim, the jury may rule in the favor

Jan 1, 2004

By Joseph L. Fournier

Suncor Oil Sands employs delayed coking technology in converting bitumen into synthetic crude oil. Currently up to 10,000 m3 of delayed coke (coke) is produced per day as a byproduct of the upgrading process, of which up to 9,000 m3 per day is placed in dry storage on Lease 86/17. A review was completed to examine the case history of leachate potential experiments from the dry storage of coke and the environmental relevance of coke leachate studies conducted over the past decade. The review included an evaluation of the potential impacts of environmental conditions within the location of coke storage, including precipitation pH, as well as daily and annual ozone trends. Coke leachate potential has historically been characterized using standard leachate testing protocols (i.e., TLCP, SPLP) together with other studies that have employed strong acids and oxidizing agents in the extraction fluids. The present paper highlights prevailing conditions in the Athabasca Valley air-shed with emphasis given to ambient ozone (oxidizers), as well as precipitation pH and acid input deposition rates, and will demonstrate that TCLP / SPLP tests lack the intended environmental relevance relative to the conditions under which coke is stored.

May 1, 2011

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

Jan 1, 2007

The Dynamics and Thermodynamics of Absorbing Lithium of Ion Sieve Preparing Pollymetallic Nodules

Sep 13, 2010

Introduction Aggregate mining impacts on water resources are a source of concern to local governments. To evaluate those impacts, the Minnesota Department of Natural Resources conducted a four-year study at three gravel pits (two alluvial and one beach-ridge) and five quarries (flat-lying Paleozoic limestone). This research provides the first comprehensive look at aggregate mining impacts on ground-water systems in Minnesota. The results will be used by government officials making permitting decisions about aggregate operations and by responsible owners of aggregate mines as they plan their operations to avoid conflicts with neighbors and with resources dependent on ground water and surface water. Natural aggregate (crushed stone, sand, and gravel) is a vital part of our economic infrastructure in Minnesota. Aggregate is used for road and bridge construction and in a variety of building materials. In 2003, the value of construction sand and gravel and crushed stone in Minnesota was approximately $245,000,000. As Minnesota’s economy continues to expand, the demand for aggregate will continue to grow. Sand and gravel pits are located in every county in Minnesota. In 1990, the Minnesota Department of Natural Resources, Division of Minerals (DNR Minerals), estimated the number of active and inactive operations at 1500 with the view that this number was likely too low. Quarries for mining limestone, dolomite, sandstone, and hard rock (granite and quartzite) are found in 34 counties. A 1990 DNR Minerals inventory found 165 active operations, 88 percent of which were limestone quarries (Nelson and others, 1990). That same inventory counted 1,367 inactive operations, 70 percent of which were limestone quarries. Aggregate mining is an extractive use of resources: mining alters the landscape and its natural hydrologic system. When a new pit or quarry is proposed or when an existing operation needs to expand, local governments and citizens typically have many questions about the impacts mining might have. Local governments, which are responsible for reviewing these operations, rarely have the budgets to hire experts to evaluate potential impacts of quarry and gravel pit proposals. The Minnesota Legislature’s Aggregate Resources Task Force identified that local government units (LGUs) often lack the expertise to assess ground-water models (Southwick and others, 2000).

Jan 1, 2007

By W. E. Falck, A. Usubiaga, J. Spangenberg, P. Schepelmann, S. Šolar, D. Wittmer, F. Blanchard

The extraction and processing of mineral resources may be accompanied by environmental impacts. In spite of technological advancements, the enormous increase in production volumes within the last decades has induced sizeable environmental impacts along the life-cycle of products. Beside environmental impacts, social issues associated with mining need to be considered to ensure the social acceptability of mining activities. The project EO-MINERS aims at deploying Earth Observation (EO) tools to inform best practices in mining and to thus assist the global mineral resources industries in their transition to sustainable development. In order to facilitate the handling of complex sets of information requirements from a wide variety of stakeholders, a set of indicators was developed that will inform the process of EO tool and services development. The project strives to enable stakeholders outside the industry to meaningfully participate in decision-finding processes on mining-related issues by developing and providing EO products and services that fit the information requirements. The project has identified a wide range of such information requirements by stakeholders that could be potentially provided by EO tools. The applicability of the EO tools on the local level is tested on three mining sites.

Jan 1, 2011

By I. Loomis, D. Rachmad, I. Duckworth

During the past two years the Underground Mine Ventilation Group at PT Freeport Indonesia has undertaken to upgrade their Hygiene Laboratory. This process has included upgrading equipment for dust sampling and gas monitoring, as well as procurement of an OCEC analyzer for Diesel Particulate Matter analysis. While the laboratory equipment represents one factor, these changes have also required re-evaluation of the sampling protocols and the burden of ventilation monitoring personnel. This paper provides a review of these experiences.

Jan 1, 2006

Jan 1, 1971

By N. A. Gjostein

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

By D Rubery, C Croker

The Boddington Gold Mine (BGM) is located 120 km south east of Perth, Western Australia. The operation is managed by Worsley Alumina Pty Ltd and mined by contractor Henry Walker Eltin (HWE). The mine has been operating since 1987 with ore extracted from a series of pits along strike. Ore is contained within the basement rock, which is overlain by a cap rock layer and transition zone. Cap rock and basement zones require blasting.As the mine neared completion, a high-grade deposit was discovered within 50 m of an existing Western Power substation and 100 m from the processing mill. The substation provides power to the Boddington area and is a back-up power supply to the city of Perth. Due to the delicate nature of the transformers located at the power station, overhead power lines and the mill, blasting in the area was considered very high risk. As such blasting needed to be controlled for flyrock, airblast and most importantly peak vibration and frequency limits which had the potential to damage the transformers.The mine was due for closure in March 2001. The decision to mine the pit was based on its high grade, ability to be blended with lowering grades from other pits and changing of the processing technique with the expansion. This decision extended the life for a further six months.Due to the high potential risks a detailed risk assessment was conducted by Orica, Worsley and Henry Walker Eltin. The completed assessment and the major design parameters were presented to Western Power for approval. The ability to reduce the blasting risk was focused on limiting of vibration through controlling maximum charge initiated per delay, blast timing and firing direction, and other innovative control measures. OricaÆs SHOTPlan« and Sabrex« computer modelling packages were used to predict the outcome of blasts.The success of this project has opened the doors for other high risk blasting projects, which otherwise may be left unmined.

Jan 1, 2002

Elected Died 1903 * ADAMS, CHARLES C. 1905 1884 *ADDY, MATTHEW 1896 1894 *ALLFN R B 1896 1874 *AMIOT, H 1892 1886 *AMSLER, CARL 1894 1895 *ÅNGSTROM, CARL 1901 1895 *ARMSTRONG, JOHN F 1898 1882 *ARNOLDS, HUGO 1886 1875 *ASHBURNER, CHARLES A 1889 1872 *ASIIBURNER, WILLIAM 1887 1883 *ATKINS, C M , JR 1885 1897 *AYERS, WILLIAM 1898 1885 *BABCOCK, GEO H 1893 1884 *BAILEY, EDWARD 1889 1880 *BAILEY, JACKSON 1887 1900 *BALLOU, FRANKLIN 1903 1886 *BARNES, F W 1892

Jan 1, 1910

By D Vickers, N C. Fowke

The reduction of geological risk for planning of high production longwall faces is essential. Geological and geophysical techniques applied at Huntly West Mine before 1989 were unable to reduce the geological risk to an acceptable level. The success of a trial long-hole directional drilling programme at Huntly West Mine (Fowke et al, 1989) has encouraged the Coal Corporation of New Zealand to use the technology long-term, for seam definition. Initial drilling in 1989 completed a total of 3543 metres, with the longest borehole length being 369 metres (limited by number of rods available). A major re-interpretation of seam structure resulted from the drilling, which was able to fill in seam details between surface exploration boreholes. The undulating thick seam conditions at the mine require a refinement of drilling strategies used overseas. Long-hole directional drilling also displays potential for inseam gas drainage. Gas flows of the order of 1000 L/min were initially indicated in individual boreholes. Other gas parameters of the seam have been studied by Beamish et al (1991), and highlight the significance of the natural gas resource in the Huntly Coalfield.   The continued development of drilling technology will be of major benefit sustainable development, particularly in policy.

Jan 1, 1991

By J L. Maule, S J. Mathews, K A. Rodgers

Gold and Silver bearing epithermal veins of the Golden Cross deposit are hosted in Miocene and Pliocene calc-alkaline volcanics occurring 8 km northwest of Waihi at the southern extent of the Coromandel Peninsula, North Island, New Zealand. Veining occurred during a period of hydrothermal activity that began early to late Pliocene, and possibly continued into the Pleistocene.   Field relations and petrographic relationships reveal that multiple generations of FeS2 occur in the Golden Cross region, with FeS2 occurring in all nine rock types recognised at Golden Cross. The variability of FeS2 morphology was investigated by preparation of high purity FeS2 separates, and grain counting. Marcasite is the dominant FeS2 phase at Golden Cross, and along with pyrite is shown to have a systematic habit variation. Pyrite shows a sequence from cubes through octahedra to pyritohedra to dendritic growth. This pyrite sequence conforms to an experimentally determined sequence. The parallel sequence for marcasite at Golden Cross is from tabular through bladed aggregates to euhedral miscellaneous marcasite morphologies. The FeS2 sequences observed are believed to be due to increasing temperature, and perhaps also increasing FeS2-oversaturation and fluid flow.

Jan 1, 1994