Search Documents

By Davorin Kolic, Harald Wagner

Conventional ground support in accordance with latest state-of-the-art considers proper preparation of geotechnical investigation, structural design, observation during construction and fair risk sharing documents. Depending on the ground, there are different means and methods, reflecting different experiences. The paper is presenting ground support concepts, as mostly used in Europe during the past three decades. It discusses the use of anchors as well as the use of steel arches respectively combinations. It also discusses different applications of plain shotcrete, respectively fibre reinforced shotcrete. As excavation sequence is a major input to create the ground arch, the paper discusses also criteria to create closed ring conditions. Finally deformation criteria will be presented with case histories in order to control stability of the structure.

Jan 1, 2001

By David H. Tang

Massive pillar failures were observed at two underground coal mines. The results of stability analysis using traditional pillar design formulae did not agree with the underground observations. Finite element models were used to analyze the causes and mechanisms of the pillar failures. The results were confirmed by the underground observations. Finally, the improved mine plan for each case was derived to ensure the stability of the underground structure.

Jan 1, 1990

By J. R. Allsup

Air pollutants in exhaust gas produced from LP-gas (propane) were studied using both laboratory engines and vehicles. The objective of the study was to evaluate engine parameters relating to the advantageous use of propane as a low-pollution fuel. Some comparisons are made between gasoline, natural gas, and propane. Results show that engines can operate over a wider range of A/F with minimum carbon monoxide and hydrocarbon emission when using propane than when using gasoline. Mixture enrichment using propane is unnecessary during cold starts, thereby eliminating the emission penalty during warmup. Carbon monoxide and hydrocarbon emission using propane are unaffected by ambient temperature. The photochemical reactivity of hydrocarbon emission is considerably lower with propane than with gasoline.

Jan 1, 1972

"The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copperzinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products.Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance.Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of run-of-mine and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling.One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost, and reagent consumption.Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ‘equivalent’) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties, and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ore becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance, and thereby profitability, is a powerful tool.In an operation such as Antamina, where managing ore sources, campaigns, and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency."

Jan 1, 2005

The Bega granite at Whipstick, N.S.W., consists of a granite metasomatically altered to leucogranites and a spessartite-granite. The ore occurs in pipes controlled by jointing and shows evidence of post-depositional tectonic forces.The principal ore minerals are molybdenite and bismuthinite, with minor amounts of uraninite, pyrite, gold, bismuth, joseite A, joseite B, tetradymite, chalcopyrite, arsenopyrite, and skutterudite. The gangue minerals are microcline, albite, quartz, muscovite, and spessartite, with fluorite, chlorite, magnetite, and biotite as accessory minerals.The intrusion of granite was followed initially by ascending metasomatic fluids which penetrated along joints to be trapped in the domed roof of the intrusion to form the leucocratic granite. Iron-manganese-rich fluids metasomatically altered the granite to a spessartitegranite which is associated with the later deposited ore.Quartz veins and dykes of varying composition post date the ore deposition.

Jan 1, 1968

By B. Simser

At Brunswick Mine, an increase in the number of seismically-related falls of ground and in particular rockbursts occurred during 1999. This was due to the ever-increasing stress levels in the remaining ore reserves, mining in difficult highly stressed areas and in particular troublesome geological features. In conjunction with the Noranda Technology Centre, development of rockburst support systems started at the Brunswick Mine in 1996 and efforts were accelerated in 1999. A support package consisting of #6 gauge chain link mesh, #0 gauge heavy mesh straps, and a 1 m by 1 m pattern of modified conebolts was developed. The conebolts were modified to enable mixing of the resin anchoring. Two major rockbursts occurred during an intense seismic episode at the Brunswick Mine from October 13th to 17th , 2000.The area was evacuated approximately four hours before the first burst hit, and remained closed during the seismic ?flurry??. The first damaging activity occurred around midnight on Friday the 13th, and a second damaging episode occurred on the 17th that included a local Richter Magnitude 2.7 event. The second rockburst had dimensions of approximately 5 m by 5 m by 20 m or 2150 tonnes of massive sulphide material (density 4300 kg/m3). The first failure area was more extensive, caving approximately six metres of an intersection back with the lateral extent not safely measurable. This paper briefly describes the mining conditions that led to the bursting, the seismic response of the region, the mechanisms thought to have caused the bursts, and a yielding support system which had been partially installed before the burst.

Jan 1, 2002

By Manuel Sanchez, Marcial Medina, Matt Hurley, Hugo Granados, Pramod Kumar, Raj Rajamani, Jose A. Delgadillo

"Large-diameter ball mills have traditionally used steel liners—steel being a highly durable material that can be shaped into any desired geometry, among which the double-wave has been the preferred design. Such a design produces a purely cascading charge motion, which is ideal for the shearing action needed to produce a finer product. Today, however, rubber liners, which have been in existence for over forty years, are now preferred over traditional steel, largely because they weigh less and are easier to maintain. In this paper, we show the operating data from the Hudbay Minerals’ Constancia Mine, wherein the liners on a 26-by-40-foot mill were changed from conventional steel liners to PolyStl™ liners. It is then shown that this change reduced the amount of energy consumed whilst being able to maintain previous grind and throughput levels. The design is verified via discrete element simulations.IntroductionThe Constancia Mine (“Our Business: Peru,” 2016) is located in the southeastern Andes of Peru, at an elevation of approximately 4,200 m. It can be accessed via the CU-126 road, about 95 km from the town of Espinar in Espinar Province. The mine also contains both the Constancia and Pampacancha deposits in the Province of Chumbivilcas. Hudbay Minerals, Inc. acquired the mine in 2011, through the purchase of Norsemont Mining, Inc. and currently retains sole ownership of the property. Production of the Constancia Mine began in 2014, with commercial production levels being achieved in April 2015.The Constancia and Pampacancha deposits primarily include hypogene, supergene, and skarn ores. The Mine’s main products, however, are copper concentrate, with silver contents, and molybdenum concentrate. These mineral reserves are expected to last approximately 22 years. Constancia’s open-pit mine supplies a processing plant that is designed for 81,900 metric tons per day of throughput. Average annual copper production is estimated to be 82,000 mT (contained metal in concentrate). Actual plant production can be found in Table 1."

Jan 1, 2017

By J. R. Ross

A reconnaissance for sources of scandium and a metallurgical investigation of recovery methods for byproduct scandium from uranium mill solutions were conducted by the Bureau of Mines. The work on scandium was undertaken to obtain information on domestic resources and to explore and develop recovery procedures in consonance with the Bureau's long-range program for conservation and wise utilization of mineral resources. The element scandium is widely distributed in the earth's crust in trace amounts, but it seldom occurs as an important constituent in any mineral. An exception is thortveitite, (Sc,Y)2 Si207) a rare mineral that contains various amounts of scandium and yttrium and may contain up to 42 percent scandium oxide (SC203). Knowledge of the chemistry of scandium has expanded rapidly in recent years (1, 4, 9)4 but only fragmentary information is available about the metal because it is still largely a laboratory curiosity without established uses (2, 3). A recent study shows some of the physical proper-ties of the metal are (1) density of 3.05 grams per cubic centimeter) (2) melting point of 1,540° C, (3) hexagonal close-packed structure) (4) hardness of about 50 Brinell (500-kilogram load), and (5) an alloy behavior similar to yttrium and rare-earth metals (2). The price of $2,850 a pound for scandium oxide of 99.9 percent purity and $2,700 a pound for oxide of 99 percent purity reflects the scarcity and complex chemistry of the element.

Jan 1, 1962

By E. Pezennec

A voluntary comprehensive environmental Risk Assessment was launched at the end of 2004 by the International Chromium Development Association. The completion is scheduled for mid 2006.EURAS, a leading environmental consultancy, was commissioned for this project, as this firm wrote in particular the Metals Environmental Risk Assessment Guidelines, the reference document for the metals and metals compounds, in particular for the forthcoming European new Chemical Policy and the Globally Harmonized System for the Classification and Labelling of Chemicals (GHS). This project follows a stepwise approach, comprising 3 distinct steps: - Initial Risk Assessment: compilation, evaluation of the existing effects and exposure data for chromium III compounds and chromium metal. This information will be used for the compilation of an initial Risk Assessment Report. - Data gap analysis: which type of additional effects data should be collected and/or which exposure scenarios merit a more detailed targeted risk assessment? Recommendations and/or suggestions for further research will be formulated. - Road map: prioritization and ranking of the different proposed research programs. The presentation will mainly focus on the results and recommendations of the initial environmental Risk Assessment from an International perspective and not from an European point of view. - Hazard assessment ? definition of the Predicted Non effect Concentration (PNEC) for each environmental compartment (water, sediment, soil) - Exposure assessment ? definition of the Predicted Environmental Concentrations (PEC) for each environ-mental compartment - Comparison of the local PEC with PNEC for the chromium III compounds and chromium metal EU industry sectors covered in the project: mining of chromite, metallurgical production of chromium metal, chromium containing alloys production, production of trivalent chromium chemicals and the main applications (pigments, leather tanning, etc..). The current status on the environmental Classification and Ranking for chromium III compounds, Chromium metal and its alloys in the GHS will also be covered.

Jan 1, 2007

By B. Oraee

Accurate estimation of equipment costs is a key factor in feasibility study and evaluation of design alternatives of mining projects. In this paper, capital and operation costs of backhoe loaders are estimated using multiple linear regression (MLR), based on principle component analysis (PCA). These cost functions are consisted of five independent variables; bucket size, digging depth, dump height, weight and horse power. The MLR is conducted in two steps. At the first correlation between independent variables is omitted using PCA technique. Thereafter, MLR functions are established using selected significant PCs and total cost functions are constituted as functions of initial variables. At the end, accuracy of functions are evaluated using mean absolute error rate method.

Jan 1, 2011

By H. Ewaschuk

"INTRODUCTIONRio Algom's Stanleigh Mill in Elliot Lake began production in June of 1983. The highly instrumented mill treats uranium ore at an average rate of 3900 metric tons per day. To help ensure a good start-up and low operating costs, an extensive training program was undertaken prior to and during start-up. This presentation describes how an unconventional operating crew were combined to form an operating unit with a high efficiency in terms of production and labour utilization. I would like to point out at the outset that the operating philosophy, and the role of the supervisors and the operators as set up at Stanleigh is not unique. Indeed, I have seen the same results at a couple of small plants where efficiency meant survival. However, these situations appeared to be the exception, and it was not readily apparent how similar results could be obtained in a larger plant. A factor that existed at the time was low labour turnover. As in most parts of Canada, jobs were easy to get in the Elliot Lake camp in the late 1970's. This, and other factors, contributed to an unusually high labour turnover. This changed dramatically in the early 1980's. Indeed, Rio's two other operating mills, Quirke and Panel reduced crew sizes at this time to reduce operating costs. As a result all of Stanleigh's operators came from Quirke and Panel with experience varying from 4 to 7 years. The experience that operators had was obviously of benefit and served to reduce the scope of the training program from what would have been required with inexperienced personnel."

Jan 1, 1985

The distribution of chrome spinels in a magnetically fractionated ilmenite concentrate sourced from the Murray Basin was characterized by XRF assaying, quantitative electron microprobeanalysis, grain mapping, automated mineral phase clustering, and modal analysis. At least 14 distinct chrome spinel types were present in the concentrate. There is considerable variation in the amount of each chrome spinel type present, although a high-Mg, high-Al phase makes up close to 45 per cent of the total spinel population. Magnetic fractionation results showed significant variation in the composition and relative abundance of spinels reporting to each fraction. Low magnetic field strength fractions (ie. high susceptibility grains) were dominated by chrome spinels that are mid-range in Al and Cr. These spinels have the highest magnetite, ulvospinel and Fe(Al,Cr)2O4components. In comparison, the high field strength fractions (i.e. low susceptibility grains) have the majority of the grains with high-Al contents indicating a higher proportion of Mg(Al,Cr)2O4component. Spinels high in a (Al,Cr)2.67O4non-stoichiometriccomponent are absent at low field strengths but tend to be concentrated in the high field strength, non-magnetic fractions. Intermediate field strength fractions tend to exhibit a broad spread in spinel compositional types. A mild roast treatment of the sample had no clear effect on the distribution of chrome spinels between different magnetic fractions, but it did cause a change in the magnetic properties of the accompanying ilmenite grains. The effect of more extreme roasting conditions on the magnetic properties of the chrome spinels is to be determined.

Jan 1, 2003

By Keith Pucalik

Understanding Vibrations fr om Blasting focuses on explaining blast vibrations and their effects on people and homes while keeping an eye on the importance of the use and significance of explosives in our daily lives. Unlike many predecessors, this film will help blasting pro f e s s i o nals explain blast vibrations and address many of the layman’s most fre q u e n t l y asked questions. The film can be used in pubic hearings, given to homeowners during preblast surveys, or played at educational seminars for professionals. The film can also be used after blasting has begun and residents have already experienced vibration events.

Jan 1, 2004

Canadian mining giant Teck Resources Ltd. will be the exclusive supplier of the metals used in the production of the more than 1,000 medals to be awarded at the Vancouver 2010 Olympic and Paralympic Winter Games. Teck, the diversified resource company headquartered in Vancouver, B.C., is providing 2.05 kg (4.5 lbs) of gold, 1,950 kg (4,300 lbs) of silver and 903 kg (2,000 lbs) of copper sourced from its operations around the world. In addition to the raw materials mines, this year?s medals will make Olympic history as they will be the first to contain metals recovered from processing the circuit boards from end-of-life electronics (e-waste) that would have otherwise been destined for a landfill. After mining or production through a variety of smelting and recovery processes, each metal has been refined to enhance the metal purity.

Jan 1, 2010

By Peter Ryan

A patented process for agglomeration of Smelter ESP dusts is described. Addition of suitable binders followed by compaction, transforms fine, difficult to handle material into a dry, flowable agglomerate suitable for plant reentry. Details for the agglomeration process metallurgy and laboratory pilot plant testing are discussed. An example of full scale plant operations is described.

Jan 1, 1999

By J. J. Sammarco

Illumination is essential for mine safety because miners depend most heavily on visual cues to detect hazards associated with slips/trips/falls and powered haulage. The National Institute for Occupational Safety and Health (NIOSH) is conducting mine illumination research to improve miner safety by enhancing a miner?s ability to see mine hazards. Thus far, 16 papers have been published covering diverse topics such as cap lamps, machine-mounted lighting, glare, lighting maintenance, and light-emitting diode (LED) technology issues. NIOSH has also developed an LED cap lamp, LED area lighting, and a Visual Warning System (VWS). This paper provides an overview of the improvements from NIOSH-developed lighting that include: 94% faster trip hazard detection with the NIOSH LED cap lamp; 79% faster peripheral motion detection to detect pinning/striking hazards; no increase in glare; 71% faster machine movement hazard detection with the VWS. Current research is described concerning an LED cap lamp for metal/nonmetal miners, illumination for refuge alternative deployment and inspection, and whether lighting could be used to improve miner escape and rescue in smoke. Lastly, future possibilities of using lighting to improve miner safety are described.

Feb 27, 2013

A good deal of experimental work has been done from time to time on the application of compressed air to the elevation of wet pulp. On account of the flat nature of most of our mill sites elevation of the pulp has to be provided for, and the various methods in vogue show considerable loss of time, in the replaceing of wearing parts. During the last two years the writer has carried out a great many experiments with a view of devising an elevator that will give continuous work with a minimum of wear.The results do not show a high efficiency for the power employed, but the lift is continuous in operation, very cheaply installed, and possesses no wearing parts. The lift was tried working in a bore hole of 8 in. diameter, but in many cases it is more convenient to sink a small well for the purpose. The result to date showed that the most efficiency was obtained when the depth of the wellwas not less than the height of the lift required. The pressure of air required in pounds per square inch was (approximately) half the number of feet to be lifted.In the majority of cases the lift required varied between 20 ft. and 50 ft. and the air pressure required between 10 lbs. and 25 lhs. per square inch. In most existing installations the air compressors in use were delivering air to the receivers at about four times that pressure, and when air so compressed was expanded to perform its work at a reduced pressure, it was apparent that the power exerted in origInally compressing the air above the working pressure required at the lift was absolutely lost.

Jan 1, 1901

By Steve Dubnewych, Jon Kaneshiro, Calvin Jin

The Joint Water Pollution Control Plant (JWPCP), operated by the Sanitation Districts of Los Angeles County (the Districts), treats wastewater generated by over3 million people and processes wastewater solids generated by over 5 million people. The JWPCP Tunnel and Ocean Outfall Project, if constructed, would be one of the major marine outfall projects in the world. The new tunnel and ocean outfall system would provide relief to the existing outfall and allow inspection, maintenance, and repair of the existing tunnel and outfall system, portions of which were constructed as early as the 1930s. Geologic conditions are challenging along the alignments within the study are a being considered. Conditions include saturated alluvial soils, weak sedimentary rock, mixed face conditions, and squeezing ground conditions. Other significant challenges include the potentials for encountering up to 11 bars of water pressure, crossing seismically active faults, and encountering gassy and contaminated ground conditions. This paper discusses the details of the proposed project and the associated challenges.

Jan 1, 2007

By T. J. Lynch

A new class of polymeric dispersants for industrial minerals has been synthesized and evaluated. Currently available dispersants give initial low viscosities at high mineral loadings, however slurry viscosities can rapidly double or triple on standing over the first several days. The new dispersants give low initial viscosities that are more stable and maintain a lower viscosity for at least one month. The new dispersants are made possible by controlling the polymer molecular weight distributions during their manufacture such that essentially all of the dispersant is adsorbed onto the mineral surface, preventing depletion flocculation.

Jan 1, 2012

By Grigore Matei

The thermodynamic properties of CuzS-FeS system are important not only in the ease of copper smelting but also in the case of general pyro-metallurgy. However there arc not many reported activity data In this study, activities of FeS and CU2S in the Cu2S-FeS system were calculated using the Darken's method from the activity data of the Cu2S-FeS-Sb2S3 systems measured by the transportation method at 1050°C. The activities of Cu2S and FeS in the Cu2S-FeS system showed negative deviation from the ideal behaviour and satisfied the relation of the Gibbs-Duhem equation.

Jan 1, 2003