Search Documents

By Hugh O?Neill

IN PREVIOUS papers,1 the author has reported the results of experiments on the straining in tension of a single crystal test piece, about 0.6 in. long, of vacuum-melted electrolytic iron containing 1.8 per cent. of silicon. The crystal was originally in the "as cast" condition, and was stressed slowly along a tetragonal axis so that slipping along conjugate gliding planes finally transformed the original cylindrical portion into a pair of fracture wedges. One of these fracture wedges was sectioned along the stress axis in a plane at right angles to the edge of the wedge. A metallographic study of this plane of -section led to the conclusion that slip had taken place in the (111) direction along (112) planes making a V shape with the stress axis. The present paper describes the results of scratch-hardness tests conducted on the same section, in order to determine the distribution of strain hardness therein, followed by annealing, and considers the resulting variations in hardness. These observations supplement those made by Krivobok2 on similar material reduced 25 per cent. by hammering (i. e., by impact) in the cold. In order to investigate ageing effects, two small crystals of the same alloy were also tested.

Jan 1, 1928

By T. E. Gray

This report describes the preparation characteristics of the most significant coal beds in Wise County, Va. It is one in a series of reports planned to determine coals suitable for the production of metallurgical coke, either as mined or after beneficiation. Wise County produced approximately 6,600,000 tons of coal in 1955, of which about 2,110,000 tons was cleaned mechanically. The Federal Geological Survey has estimated that 1,341 million tons of measured and indicated coal reserves remained in the county as of January 1, 1951.

Jan 1, 1958

By Murphy A. S, Budod A

The Philex concentrator represents the first time Jameson Cells have been used in a cleaner scavenger application or in large scale flotation in roughing and scavenging. This necessitated a major change in Jameson cell design as well as a chan

Jan 1, 1997

By Allan T. Gwathmey, J. Bruce Wagner, Kenneth R. Lawless

Between 250°and 550°C in oxygen pressures of 10 to 760 mm Hg, the relative oxide thicknesses formed per unit time on the (100), (111), (110), and (320), decreased in this order. The predominant oxide orientation was (001)Fe3O4 and [110] Fe304 A small amount of a-Fe2O3 which exhibited a fiber pattern was observed in all oxides except those formed at 250°c in low oxygen pressures. IN order to understand the properties and behavior of thin films, particularly their role in oxidation reactions, there is needed more experimental information on their structure, composition, and kinetics of formation on clean surfaces of known geometry. The present study was undertaken to obtain such information for thin oxide films formed on single crystals of a body centered cubic metal, iron. Crystals in the form of spheres were used in order to expose all possible crystal planes to the reactant gases simultaneously. Using this procedure the relative rates of oxidation of all planes could be estimated, and those exhibiting, maximum or minimum oxidation rates could be selected for a more intensive study of composition and expitaxy. Since the three types of information were obtained from the same experiment using a single crystal substrate, any differences between rate, composition, and expitaxy on the several planes may be attributed to the influence of the substrate structure. EXPERIMENTAL The starting material for this study was Armco iron rods, 6 in. long and 3/8 or 1/2 in. in diam. The analysis was reported to be 99.8 pct Fe, with major impurities listed as carbon 0.018 pct, manganese 0.027 pct, phosphorous 0.005 pct, sulfur 0.029 pct, silicon 0.005 pct, and copper 0.11 pct. These rods were cleaned with ether and heated in an atmosphere of moist hydrogen at 950°C for three days. The purpose of this treatment was to decarburize the iron and to provide a consistent, uniform grain size for the growth of single crystals. Crystals in the form of rods, up to 1/2 in. in diam and 2 in. long, were prepared by a method similar to that reported by Leidheiser and Buck.2 Spherical crystals, 3/8 and 1/2 in. in diam and having a handle about 1/4 in. in diam by 112 in. long, were machined from the single-crystal rods. After machining, each crystal was etched in aqueous nitric acid to remove the cold-worked metal at the surface. Before each experiment, the crystal was polished mechanically with metallographic papers through number 4/0, and electropolished in a perchloric acid-acetic anhydride mixture by the method of Jacquet and Rocquet.3 The crystal was washed in running distilled water for at least 5 min. The excess water was blotted with a soft paper tissue, and the crystal was placed in an all-glass reaction vessel (See Fig. 1). The crystal was heated at 550°C in hydrogen for at least 8 hr prior to the oxidation in order to reduce any surface oxides and to help relieve any stresses in the metal. For the structure and composition studies, flat faces were cut parallel to (loo), (111), and (110) planes on the iron crystal spheres. The orientation of these faces was checked by a back-reflection X-ray diffraction technique. The faces were within 2 deg of the desired orientation. The flat faces were treated as described above except that prior to electropolishing they were given an additional polish on metallographic felt saturated with twenty-minute levigated alumina. After the crystal was heated in hydrogen for at least 8 hr, the temperature was adjusted to the desired value, and the hydrogen was evacuated. Commercial oxygen which had been purified by successively passing through tubes containing magnesium perchlorate, Ascarite and magnesium perchlorate was admitted to the desired pressure as measured by a mercury manometer. A resistance-wound furnace surrounded the oxidation chamber, and a temperature controller maintained the temperature within ±3°C. The furnace was provided with a small window for observing the crystal. The changes in thickness of the oxide films were followed by observing the interference colors. The oxidation was allowed to proceed until the desired oxide thickness was attained on a given crystal plane. The experiment was terminated by evacuating the oxidation

Jan 1, 1962

By Basil Prescott

Resume.—The district of Santa Eulalia lies 12 miles to the southeast of the city of Chihuahua, Mexico. The ore deposits occur in a Cretaceous limestone of unknown thickness, overlain by a series of rhyolitic tuffs and flows. The limestone is very gently folded and is cut by several systems of fissures, of which only those with a general north-south strike are pre-mineral and control the deposition. The deposits are of two main types; the earlier silver-bearing iron sulphide type occurs as high-grade tabular bodies resembling veins and as large masses of relatively low-grade ore, The gangue of this type is composed of lime-iron silicates that point toward a close association with an igneous rock mass which has not yet been encountered. In the later silver-lead-zinc type the ore occurs in vertical chimneys and horizontal mantas, principally as oxides, though at a depth of 1,500 ft. some sulphides have been encountered. During oxidation the ore chambers have increased in size owing to the solution of the walls by the sulphuric acid generated in the process, and a substitution has taken place of nearly one-half part by weight of the original constituents of the ore, by newly introduced elements and radicals. Both types are believed to have come from greater depths than those yet reached by mining, and their ultimate source, from a consideration of similar deposits, is believed to be an igneous rock in contact with the limestone at some horizon below. The deposits are believed to have been formed at unusually great depths, as indicated by the proved great vertical range of the silicate minerals coupled with the absence of the igneous rock, and by the practically unchanged character of the silver-lead-zinc ores as far as developed. The volcanic capping is believed to be distinctly later than the economically important ore deposition. Introduction The Santa Eulalia district is situated in the State of Chihuahua, Mexico, and lies about 12 miles southeast of the capital, the city of Chihuahua. (See map, Fig. 1.) The district embraces the Sierra de La

Jan 1, 1915

By Michael Perch, Charles C. Russell

Nearly 95 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69,9, and in 1938 it was 61.3, To produce a net ton of pig iron 1959 lb. of coke was required in ,1940 and 1760o lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1942

By S. Senderoff, D. E. Couch

A PROCESS for the electrolytic preparation of molybdenum from molten salts has been described previously. This previous work centered on electrowinning and electroplating characteristics of the process. In this paper the properties of the process as a refining medium are discussed. In producing metals from ores, it frequently has proven most economical to obtain a comparatively impure metal by smelting, and to purify the product by electro refining. Direct electrowinning from molten salts is rather difficult when a porous diaphragm is required in the process, as in the case of molybdenum, since satisfactory refractory materials for such a diaphragm in molten salts have not yet been developed. In electrorefining, however, a soluble anode is used. By suitable control of anode and cathode current densities, the lower-valent molybdenum compound used in the electrolyte is not oxidized, and a diaphragm is not needed, thus avoiding difficulties which are encountered with other electrowinning processes. Electrorefining may result from two different processes in the cell: Dissolution of the molybdenum and the less noble impurities with a separation of the more noble impurities as an anode sludge; the electrodeposition of molybdenum and the more noble metals at the cathode, leaving the less noble metals in the electrolyte. The amount of separation which occurs in each process is determined by the potential of the operating electrode and the relative concentration of the various species at (or in) that electrode. Since molybdenum has a comparatively noble position in the EMF series in molten alkali halides,2 most refining would be expected to occur at the cathode. In this work only the cathodic process was studied. The objective was to determine to what extent various metallic ions, if they dissolve from the anode or are otherwise introduced, were concentrated in the electrolyte. The necessary conditions for the separation of each and the limiting concentration which may be tolerated in the electrolyte for effective refining were studied. The deposits were chipped from the cathode and analyzed spectrochemically for metallic impurities. Besides determining the major contaminant, a general qualitative analysis was obtained to be sure that other metallic ions were kept at a very low level during each series of runs and to be sure that the baths were not being contaminated accidentally. Samples of the bath, for analysis, were taken at the temperature of operation so there was no chance of selective crystallization during cooling. In this way the ratio of molybdenum in the bath to the other metal could be determined readily. These data permitted a check on the anode efficiency and any volatilization that took place during the electrolysis. Experimental Apparatus—The apparatus as shown in Fig. 1 was used to determine the effect of the various foreign ions upon electrodeposited molybdenum. The entry chamber A allowed the cathodes to be removed without cooling the bath and without allowing oxygen or moisture to enter." The cathodes were made Prom 0.25-in. tungsten rods and were rotated during the electrolysis. The balloon in the lower arm B was inflated with helium after the cathode was drawn up into the upper section for removal. A new cathode was then placed into the entrance chamber A after which the chamber was flushed

Jan 1, 1959

By J. Brett, L. Seigle, L. Castleman, T. Montelbano

Impurity-induced low-temperature recrystallization of cold-worked tungsten was inuestigated with emphasis on the influence of nickel on the reaction. Palladium, nickel, aluminum, manganese, platinum, and iron greatly lower the recrystallization temperature of doped tungsten, which zs normally very high, but the recrystallization temperature of electron-be am zone-refined tungsten wzre is slightly raised by conlacl with nickel. Recrystallization can be induced at low temperature by the presence of solid nickel on the surface of doped tungsten wire, but apparently not by exposure to nickel vapors alone. Approximately 200 ppm of Ni dijjused into 10-mil wires at 1200 from a deposit of nickel on the surface produced total recrystallization, whereas more than 600 ppm of Ni could be absorbed frotn a vapor source without altering the fibrous structure of cold-worked tungsten. Once initiated, nickel-induced recrystallization required a continued source of' nickel for propagation of the recrystallization front. The solubility of nickel in fibrous 10-mil W wire was approximalely 500 ppm at 1150' C, and the activation energy for penetration of the recrystallization front was 52 kcal per mole. In many applications the usefulness of tungsten depends on critical control of its structure. Cold-worked tungsten with the fibrous structure developed by suitable thermo-mechanical treatment has a low, but technologically significant, ductility. It has long been known1 that traces of nickel, and perhaps other metals, are profoundly deleterious in doped tungsten, because they induce recrystallization at low temperature, which produces a brittle, equiaxed grain structure. This effect appears to be an exception to the general observation that recrystallization is impeded and the recrystallization temperature raised by the presence of impurities.2"9 Previous studies7-'' of the annealing and recrystallization of tungsten wire have divided the phenomenon into prior recovery stages, primary recrystallization and secondary recrystallization. The present investigation is concerned principally with primary recrystallization which is defined here as the replacement of the fibrous structure of deformed tungsten by equiaxed grains. The objective of this study was to explore the nickel-induced recrystallization reaction in tungsten and attempt to elucidate its mechanism. As well, an effort to define which other elements give rise to low-temperature-induced recrystallization was carried out. EXPERIMENTAL PROCEDURE The procedure adopted for these experiments was essentially to bring nickel and other elements into diffusive contact with cold-worked tungsten wires. The process of recrystallization was followed as a function of time and temperature by light and electron microscopic observations. First the influence of nickel on the recrystallization temperature of arc-melted, zone-refined, and variously doped tungsten wire was determined by electroplating a deposit of nickel on the surface of the wire and annealing at a variety of temperatures for 3 hr. The chemical analyses of the tungsten wires used in this investigation are given in Table I. The surface of the tungsten wire was etched with Murakami's slution' and approximately 0.005 in, of Ni was deposited from a Watts-type low pH bath14 for the conditions of these experiments. Variations in plating thickness from about 0.001 to 0.005 in. had no discernible influence on the resulting structures. The wires were then annealed in an atmosphere of dry hydrogen to establish the recrystallization temperature. Concurrently, un-plated specimens were annealed to establish the recrystallization characteristics of nickel-free wire. The criterion of recrystallization was that the fibrous structure be completely replaced by equiaxed grains after a 3-hr treatment of temperature. This provided more reproducible results than use of the first recrystallized grain or a fixed proportion of re-crystallized structure as the critical observation. The structures encountered in longitudinal and transverse sections were examined by both light and electron microscopy at magnifications up to X32,000 using parlo-dion-carbon replicas shadowed with platinum for the latter method. Second, the influence of a variety of metals on the recrystallization temperature of 0.010 in. D alumina-silica doped tungsten wire, AW136-64, was determined. The elements were applied by electroplating whenever possible. Alternatively, they were vapor-plated on the tungsten wire and a greater thickness built up by coating with a dispersion of metal powder in nitrocellulose lacquer. Elements not amenable to either of these procedures were merely slurry coated on the tungsten. The recrystallization temperature was determined as above. Third, the nickel-induced recrystallization process in doped wire was studied more closely by electroplating 8 mils of Ni on 65-mil alumina-silica doped tungsten wire, AW153-NS10, and exposing the wire to temperatures of llOO°, 1200°, or 1300°C for various times in a hydrogen atmosphere. A circular recrystallization front, 'Onsisting of equiaxed grains, developed at the periphery Of the coated tungsten wire, and the advance of this front into the fibrous interior was studied. These experiments employed relatively coarse 0.065 in. D wire because the 0.010 in. D wire recrystallized too quickly to permit observation of the pene-

Jan 1, 1969

By A. J. Leighton

An improved mathematical model with the attendant computer program to calculate multiphase fluid flow in petroleum reservoirs is presented. The model is used to simulate the behavior when a fluid is used to displace hydro-carbon fluids in a reservoir. The method is an expansion of a previously published method, in Bureau of Mines RI 7011, but handles constant injection rate as an alternative to constant pressure. Program documentation is provided along with thorough explanations of the added program features. Using the program, the petroleum engineer can calculate oil recoveries for different flood patterns and operating conditions and select the conditions most likely to optimize recovery. Experience with the previous model demonstrated the need for the improvements in order to simulate reservoir behavior more accurately. The improved method will result in improved oil recovery. In this paper, the significant improvements are described in detail so that anyone interested can put the program to use.

Jan 1, 1975

By W. D. Sylwestrowicz

In tests on polycrystalline copper and aluminum, the ratio of the yield stress to modulus of elasticity was found to be strongly dependent on tempemture. Also, it was shown that the change of the yield stress with temperature of a material at a given temperature and deformed to a given yield stress, but not necessarily to the same strain, does not depend on previous mechanical thermal history. Likewise, for a material at a given temperature and deformed to a given yield stress, the rate of work hardening is independent of the temperature of prior stressing. It has been shown by Los and Orowan1 and by Dorn, Goldberg, and Tietz2 that the temperature dependence of the yield stress-strain curves of crystalline materials reflects two effects: not only does the yield stress of a material in a given structural state depend on the temperature, but the structural state (and the corresponding strain hardening) after a given amount of plastic straining also depends on the temperature at which the pre-straining has been carried out. Thus, for instance, if a specimen of a ductile metal has been strained along the stress-strain curve 1 at room temperature to point A, Fig. 1, and then the straining continued in liquid nitrogen along curve NR, the yield stress A' immediately after lowering the temperature is lower than the yield stress A" of a specimen that has been strained by the same amount in liquid nitrogen (along curve 3). AA' represents the effect of the temperature change upon the yield stress of the specimen pre-strained at room temperature; A' A" is the excess strain hardening acquired if the pre-straining has been carried out in liquid nitrogen instead of at room temperature. The dependence of the yield stress (i.e., of the structural state acquired during preceding straining) upon the conditions (speed, temperature) of a pre-straining is the reason for the nonexistence of a so-called "mechanical equation of state" for plastic deformation. A 'mechanical equation of state" is a relationship of the form F(s,E, e, T) = 0, or s = f(E, E, T) [1] It was first suggested by Ludwik3 that plastic deformation might obey such an equation; this, however, was conclusively disproved by experiments of Kochendorfer.4 Additional disproofs were given in

Jan 1, 1959

By Ibil S

The Gameta Gold Deposit is located on the north-eastern corner of Fergusson Island in the D'Entrecasteaux Islands of Milne Bay Province, PNG, at lat. 9¦ 25' 5, long. 150¦ 47' E or AMG co- ordinate 256740 E/8959000 N (Figure 1). The area is covered by the Fergusson (SC56-05) 1:250,000 scale Topographic Map Sheet and the Koitabu (9079)1:100,000 scale Topographic Map Sheet. The property is held 100% by Union Mining NL (UMG) and lies 105 km NNE of Alotau and 33 km to the ESE of UMGs recently developed Wapolu Gold Mine, a Joint Venture between UMO (51%) and Macmin NL (49%). The inferred resource estimated from surface results and 105 RC drill holes, currently stands at 1.89 million tonnes at 2.6 git gold (1.0 g/t Au cut-off) or 155,000 oz. Evaluation of the property is currently proceeding. To date 111 RC holes have been drilled for a total of 4611 m.

Jan 1, 1997

By G. R. Hodgson, M. P. Lebourg

The introduction in the field of a new type well completion called for the setting of tubing open-ended in the well before perforating the casing. This paper describes a new perforating tool of the shaped charge expendable type, small enough to pass through tubing and powerful enough to perforate the casing. The perforations are produced at an angle and are large enough for optimum production. Performance of this tool in targets and under various well conditions is described. Very often no lifting equipment will be available at the well. In some cases, pressure will exist in the well at the time of the perforating operation (workover wells or multiple trip perforation) ; therefore, new equipment and new technique for the perforating operation were devised. This paper describes this equipment and technique, particularly casing collar recording, sheave support, and cable pull-down device. this last item being necessary for wells under pressure. Results obtained with this tool in the field are given. INTRODUCTION One of the key requirements for the introduction in the field of a new method of permanent well completion was the development of a new perforating method involving the use of a perforating gun small enough to go through tubing and with enough penetrating power to perforate the casing satisfactorily. The equipment described in this paper was basically designed to go through open-ended two-in. tubing and to perforate 5 1/2 in. casing. The equipment is illustrated in accompanying figures. NEW COMPLETION METHOD With the new permanent type well completion, the production string of casing is run and cemented through the potential producing zone. Open-ended tubing is -then run into the well and used to replace the drilling fluid with oil or water. The amount of the oil or water "cushion" can be varied according to the expected bottom hole pressure. Thus, if desired, the hydrostatic head can be greater, equal to, or less than the expected pressure within the zone to be perforated. Mud having been displaced, the tubing is -then positioned so that the end is above the zone to be perforated. The Christmas tree and flow lines are installed and tested. The drilling rig can now be removed from the well since it is not necessary for the perforating operation, thus resulting in a saving in rig tme. The perforating equipment is then moved to the well and the gun lowered through the tubing. After the gun passes out of the open end of the tubing, the depth measurements are correlated with casing collars and the gun placed opposite the zone to be perforated. Upon firing, the gun body is shattered and falls to the bottom of the well. Since the lubricator has been closed before firing, it is possible to withdraw the casing collar locator and head and then open the well immediately to the tanks. DESCRIPTION OF GUN An investigation of two basic types of Perforators, namely a bullet perforator and a shaped charge gun, was undertaken towards the development of a gun to meet the aforementioned requirements. Preliminary tests on various bullet perforator designs within the diameter limitations did not give results encouraging enough to warrant further study. Somewhat better results were obtained by using conventional shaped charges; but, as in the case of the bullet types, the necessarily small overall diameter proved to be a severe limitation and resulted in insufficient penetration. A shaped charge employing a new design was developed which gave excellent penetration. These shaped charges were designed to produce a large hole directed upward at a 45" angle. In order to obtain the maximum space possible for these charges, it was decided to use an expendable carrier made of drillable material, usually aluminum, which would shatter at the time of firing, leaving only harmless fragments at the bottom of the hole. The fixed spacing is five shots per ft. wit11

Jan 1, 1952

By R. W. Kewish

The preparation of massive uranium metal containing very low concentrations of a number of light elements by bomb reduction of UF4, with calcium is described. Details of procedures are given for preparing high-purity ingredients for the bomb reduction. The as-reduced uranium metal contained, on the average, less than the following amounts of light element impurities, in ppm: Li, 0.1; Be, 0.1; B, 0.1; C, 25; 0, 70; Na, 1; Mg, 3; Al, 2; and Si, 7. Other impurities for which the metal was examined averaged, in ppm: Ca, < 10; V, < 10; Cr, 2; Mn, 6; Fe, 50; Co, < 5; Ni, 8; and Cu, 1. THE preparation of very high-purity uranium metal in massive form for research purposes is of great importance. Recently the kilogram-scale preparation of uranium metal containing less than 70 ppm of detected impurities was accomplished by Blumen-thal and coworkers by vacuum remelting of high-purity crystals of uranium obtained by fused salt electrolysis.1"3 Albert and coworkers4 have reported successful experiments in lowering the concentrations of certain impurity elements in uranium, notably iron, to a few ppm by the zone-melting method. The present paper describes the preparation of high-purity massive uranium metal by the bomb reduction of UF4, with calcium. Early in 1951 a program was undertaken at the Los Alamos Scientific Laboratory to prepare uranium metal of very high purity with respect to a number of the light elements. The methods considered for this purpose were 1) bomb reduction of a uranium halide with calcium, 2) electrolysis of fused salts, and 3) hot wire decomposition of UI4, The first of these processes had been used extensively at Los Alamos since 1943 (and still is used) for the production of uranium metal.5 In considering the three processes it was evident that either of the last two would require an extensive development program with no certainty of success. On the other hand, a study of available data showed that uranium metal of very high purity with respect to some light elements had occasionally been made in routine processing by the first method. It was therefore decided that an intensive study of the bomb-reduction process would be made to see if it could be improved to yield uranium metal with very low concentrations of light elements. DEVELOPMENT OF PROCEDURES The bomb-reduction process used at Los Alamos consists of reducing UF4 with calcium, using iodine as a booster. The reaction is carried out in a magnesium-oxide crucible enclosed in a steel bomb. Argon is used in the bomb to avoid objectionable side reactions which would occur in the presence of air. All ingredients for this bomb-reduction process were examined as possible sources of light elements. It was known that high-purity UF4 was required. The calcium used in the reductions was a source of carbon and magnesium. The magnesium-oxide crucibles were sources of boron, silicon, and magnesium. The iodine did not appear to be a source of any impurities. Pure UF4- The UF4 for bomb reduction is prepared from U3O3 , by successive reduction to UO2, with hydrogen and hydrofluorination of the UO2, with anhydrous HF. Since it was known that no impurities were normally introduced during the gas-solid reactions, effort was directed toward the preparation of high-purity U3O3. Of the many possible procedures for the purification of uranium solutions the following were investigated: 1) Precipitation of uranium peroxide. (Two procedures were tried. The first consisted of simultaneously adding hydrogen-peroxide and ammonium-hydroxide solutions to a uranyl-nitrate solution, containing citric and malonic acids, at such relative rates that precipitation was carried out at a constant pH of 1.5 The second consisted of simultaneously adding uranyl-nitrate, ammonium-hydroxide, and hydrogen-peroxide solutions to an aqueous solution

Jan 1, 1960

By Maurice Ewing, A. P. Craby, J. W. Peoples, J. A. Peoples

The purpose of this paper is to present the results of the application of the earth-resistivity method of subsurface investigation to the problem of locating seams of anthracite coal beneath a mantle of soil and subsoil. Details are given of the successful use of this method in locating the outcrops of anthracite seams in actual prospecting. The presence of the outcrop of an anthracite seam is indicated at points where electrical resistivity tests showed relatively low readings. The reason for this is that in some localities the resistivity of anthracite was found to be about 0.0001 megohm-cm. compared to 1 to 200 megohm-cm. for shales and sandstones. For two reasons it is believed that the data summarized in this paper should be of particular interest. In the first place, most of the interpretations of the resistivity survey have been checked by subsequent drilling and some by the removal of the overburden and the exposing of the anthracite seams. It is infrequent that the opportunity for checking results so thoroughly is given. In the second place, the fact that recent commentatorsl,2,3 on the application of geophysical methods to mining have concluded that direct prospecting for anthracite and other types of coal is not promising makes the good results obtained more significant. So far as the authors can learn, the only previous experiment with electrical methods in the Pennsylvania anthracite field was one made by Sherwin F. Kelly in 1921, when he used the self-potential method at Wilkes-Barre4. The profile he made does not show a very marked correlation with the geologic cross section. Kelly points out that stray currents from electric motors in the mines undoubtedly affected &apos;his results, but the experience of the present authors with stray currents from mining machinery suggests the possibility that the potentials measured by Kelly were due almost entirely to this effect.

Jan 1, 1936

By J. W. Snavely

WITH all the advantages of handling bulk materials by means of belt conveyor also go some problems, one of the most persistent being that of cleaning. When sticky materials are being carried; the build-up of material on the return idler rolls results in difficulty of belt training. Much attention has been given to the problem of cleaning conveyor belts, and a great variety of cleaning devices have been developed. Even the best involve troublesome maintenance, and none can completely remove the fine particles imbedded in the belt cover, which cause rapid wear of the return idler rolls, and at the same time, of the belt cover as well. One of the major rubber companies has been promoting a two-way belt system, in which the conveyor belt is given two successive 90" twists at each end to enable it to carry material in both directions simultaneously. For many years the flat belt transmission industry has installed quarter-turn and half-turn twists in countless numbers of instances. While quarter-turn and half-turn twists in transmission belts is a familiar application, the 180" twist apparently has never been previously attempted with a conveyor belt. About a year ago, two officials of the National Iron Co. of Duluth, Lester and Lewis Erickson, proposed twisting the return run of a conveyor belt on an installation that they were designing for one of the major iron ore producers. Since then the soundness of the idea has been demonstrated, both in theory and by practical test, with the result that the installation of two conveyor belts involving the twisting of the return run is now under way. These two installations are designed to have the return run of the conveyor belt twisted 180" as it leaves the snub pulley at the head drive. The clean underside of the belt is thus placed against the idlers on the return run as well as on the carrying run. Just before it enters the tail pulley, the belt will be twisted an additional 180°, restoring it to its normal position. Because this twisting of the return run of a conveyor belt is a radical departure from accepted practice, an elaborate and extensive test was conducted early in 1950 to demonstrate that this twisting of the return run could be done successfully, also to establish application data for accomplishing this twisting, and to determine if any special equipment would be required. In studying this concept of twisting the return run of a conveyor belt, a number of problems need to be solved, primarily the ones brought about by deliberately introducing an unequal distribution of stress across the conveyor belt and controlling that maldistribution of stress, while confining it to the return run portion. The tension conditions existing in the return run of a conveyor belt are clear to all designers. First, the return run carries the initial or slack side tension of the conveyor belt, the tension that must be supplied to the return run to provide proper frictional contact between the belt and the driving pulley so that the necessary power can be transmitted from the driving pulley to the belt without slippage. This slack side tension is supplied to the belt by means of takeups, either of the gravity type, which can be vertical or horizontal, or by means of the screw type. With inclined or declined belt conveyors the slope tension also must be considered, which is the tension imposed by the weight of the belt hanging from the top pulley. This slope tension frequently can furnish part or even all of the initial tension required. The maximum value of the slope tension will be at the top pulley, and it decreases in direct proportion to the length. In addition to the foregoing, it frequently is desirable to impose arbitrarily additional slack side tension to provide sufficient tension at the loading point at the tail, so that the belt will adequately support its load between the carrying idlers. Design Conditions for Twisting A number of design conditions exist, which must be satisfied successfully to accomplish the twisting of the return run without exceeding normal working limits in any portion of the conveyor belt. It is obvious that the belt edge, in its relation to the center of the belt, must stretch in making a twist, because as the twist is accomplished, the belt edge travels through a longer path than does the center of the belt. It is further obvious that if the edge of the belt is stretched, a redistribution of stress in the belt is required to allow this edge stretching. Moreover, this stress will be unequal across the width of the belt, having a maximum value at the edges, with a minimum value at the- center of the belt. With correct initial tension in the return run of a conveyor belt, the existing slack side tension will be unequally distributed when a twist is introduced. A condition then exists in which the edge stresses,

Jan 1, 1952

[Aalde, Kaare, (&apos;40) New Mexico School of Mines, Socorro, N. M. Abadesco, Enrique A., (&apos;39) Univ. of the Philippines, Manila, P. I. Abdul-Ahad, A., (&apos;39) Montana School of Mines, Residence Hall, Butte, Mont. Abreu, Ovidio M., (&apos;38) Univ. of Nevada, Reno, Nev. Acker, Voscoe, . (&apos;39) Agricultural & Mech. College of Texas, College Station, Tex. Acosta S., Gonzalo, (&apos;40) Univ. of Texas, Univ. Sta., Box 1785, Austin, Tex. Adams, Albert, (&apos;38) New Mexico School of Mines, Socorro, N. M. Adams, Charles W.,&apos; (&apos;39) Michigan College of Min. & Tech., Houghton, Mich. Adams, Hugh T., Jr., (&apos;39) Univ. of Oklahoma, Norman, Okla. Adams, Jack L., (&apos;39) Univ. of Oklahoma, Norman Okla.]

Jan 1, 1940

By Howarth W. J, Sowerby B. D, Watt J. S

On-line analysis systems have found widespread application in the metalliferous mineral and coal industries. The continuous analysis and rapid response of these systems has led to improved control of mining, processing and blending operations, with increased recovery of valuable minerals and coal combustibles.The paper reviews developments in on-line analysis by CSIRO and Mineral Control Instrumentation Ltd which led to the award of the Australia Prize 1992. These commercialised systems analyse mineral and coal slurries; determine the ash and moisture contents of coal on conveyors, and the moisture content of coke on conveyors; and determine the carbon content of fly ash. These gauges are estimated to have resulted in productivity increases valued at $50 million per year to Australia.

Jan 1, 1993

By E. E. Schumacher

IN a laboratory devoted to the furtherance of the science of communication, the breadth and variety of the problems encountered are challenging to a metallurgist. In my own long association with the Bell Telephone Laboratories, our metallurgical group has dealt with a vast number of alloys, both ferrous and nonferrous, and with many materials in the border range of metallic properties., The objectives of our design engineers embrace every phase of telephony, and the properties they desire in metals are generally unusual, frequently unique, and often conflicting. Commercial alloys have not always been available with properties to meet a special requirement in the telephone plant, and many alloys have had, therefore, to be custom-made. Anyone who has had the opportunity to observe the results of tests of all types on numerous such alloys, both commercially and specially produced, or who has taken part in the development of an alloy of some necessary, but new or unusual combination of properties, could not fail to be impressed by the frequency with which a desired goal has been reached or adequately approached through the presence of decimal quantities of alloying elements. Nor could One fail to be struck by the occasions when, conversely, of a minute amount Of impurity element has rendered an alloy useful. It is no exaggeration to state that the content be- hind the decimal point often spells success or fail-ure, and the critical content is sometimes far to the right of the decimal point as I shall later illustrate. The great effects of small additions have long been recognized and have, in fact, been described by many investigators. The importance of the minute, however, cannot be overemphasized. Therefore, in this discussion, I propose to illustrate for you some of the startling instances, drawn primarily from our own experiences, wherein small, even vanishingly small, proportions of stranger elements in otherwise common aggregates have com-pletely changed the customary pattern of behavior. No one property has a monopoly as to being dis-proportionately affected by minor elements. Nearly all properties are affected, but there is time here to include only a selected few. I have chosen, there-fore, three of general interest: strength, magnetic, and electrical properties. I shall inquire into both the mechanisms and consequences of these disproportionate effects and try to share with you the fascination and challenge of this field. Strength Properties of Lead and Lead Alloys To illustrate the effect of the minute on strength properties I have selected lead and its alloys, with which we have worked extensively for many years. Lead has the advantages of being available in quantity in a state of high purity and of being fairly easy to melt and fabricate without contamination to any extent detectable by the spectrograph. It has the interesting disadvantages of recovery and recrystallization at room temperature. Whether I

Jan 1, 1951

By L Terrusi

The Bungaroo Valley hosts a concealed Tertiary channel iron deposit (CID) along a 17 km stretch of its length. Bungaroo Valley is approximately 0.5 km wide upstream at its easternmost extent, and 3.5 km wide downstream where it joins the Jimmawarrada Creek. The valley follows the axial trace of an anticline that plunges gently to the southeast, and the CID infills the valley. Mineralisation extends to a depth of 230 m below the surface, and almost the entire deposit occurs below the water table. Bungaroo Valley cuts through the Buckland Hills and is bounded to the north and south by steep scarps capped with the resistant Dales Gorge Member of the Brockman Iron Formation. Basement rocks are believed to be mostly Wittenoom Formation shales and dolomites, with Mount McRae Shale and Mount Sylvia Formation also present. Deep, localised depressions appear at the base of the CID sequence towards the north edge of the upstream section of the valley, while downstream the basal CID contact is relatively flat and shallow. In both cases the profile of the CID surface closely mirrors that of the basal contact. The localised depressions seen in the upstream basal CID contact produce significant variations in CID thickness of up to 100 m over short strike distances. This uneven palaeotopography is most likely due to eddying and waterfalls forming within the riverbed prior to CID deposition during a time when the water table was much lower than at present. It may also be associated with possible karsting in an underlying dolomite unit and subsequent syn- or post-depositional collapse of the overlying CID. The irregular basal contact of the Bungaroo CID sequence has implications for mining in terms of pit design and resource accessibility.

Jan 1, 2007

By R. S. Craig, W. E. Wallace, G. S. Kamath

The destruction of long-range order in Mg-Cd, has previously been thought to occur as a second order process. In the present work a variety of X-ray diffraction techniques are employed to show that in this case and in Mg-Cd alloys containing frorn 20 to 33 1/3 at. pct Mg the process more nearly resembles an ordinary first order phase transformation. It is found that the ordered alloy, which occurs as a single phase at lgw temperatures, transforms with increasing temperature into a Cd-enriched disordered (P) phase and an Mg-enriched ordered (a) phase. The interval over which these two phases coexist under apparently equilibrium conditiovs extends from 25" to 87°C content. At 33 1/3 at. pct Mg the two-phase region has disappeared. Measurement of the long range order parameter, s, for the ordered phase in MgCd, (from superlattice line intensities) shows that it disorders only very slightly before it is transformed into the p form. Kinetic experiments reveal that when the a phase is formed frorn the p phase by suitably quenching so as to suppress phase segregation, the transformation is essentially complete and the a phase has acquired its equilibrium value of S in less than 1 min. In an earlier investigation carried out in this Laboratory1 the rate of disordering of the MgCd3 superlattice was determined over an extensive range of temperature. The process was found to be first order and the rate constant, k, was established. At the lowest temperatures studied k was found to increase exponentially with temperature. At higher temperatures, however, it passed through a maximum and for the 100 deg interval below the point at which the superlattice was destroyed k was observed to decrease with increasing temperature. The various theoretical treatments1-3 of order-disorder phenomena lead to a negative temperature coefficient for k near the superlattice critical temperature but this region for MgCdB seemed unusually wide. Detailed analysis of the point indicated&apos; that either the long-range order parameter, S, for MgCda varied with temperature in an anomalous way or the disordering in this instance is more complex than in the cases which have been treated theoretically. The original objective in the present work was simply to determine S vs temperature for MgCda to ascertain whether the disordering was in conformity with theoretical expectations.2° In an early stage of the work it was noted, however, that under equilibrium conditions ordered (a) and disordered (0) phases coexist in MgCd, over a considerable range of temperature. Since on thermo- dynamic grounds the coexisting phases must differ in composition, the investigation was enlarged to permit the compositions of the two phases in MgCd3 to be determined and to establish the extent of the two phase regions for alloys containing from 20 to 33 1/3 at. pct Cd.

Jan 1, 1963