Search Documents

By C. Y. Lim, H. W. Kim, M. S. Kim, J. H. Cho, Y. S. Lee

Al - 5.5 wt% Mg - 0.3 wt% Cu alloy strip was successfully fabricated by horizontal-type twinroll casting (TRC). For producing sound strips with no surface defect, the casting was conducted at various roll rotation speed, and the sound strip could be obtained at relatively low casting speed (3 rpm). The cast strip was homogenized at 450 °C for 10 hours, and then cold rolled with a reduction rate of 78%, followed by a final annealing at 450 °C for 1 hour. The annealed sheets showed good mechanical properties with approximately 330 MPa in tensile strength and 27 % in elongation, but exhibited strong anisotropy depending on the tensile directions. For the homogenized sheets, warm rolling was also conducted at 200, 300, and 400 °C. The tensile test results of the warm-rolled sheets showed that the rolling at medium temperature (300 °C) was proper to fabricate the sheets with relatively good mechanical properties and low anisotropy.

Jan 1, 2014

By Gunnar Nord, Per-Anders Persson, Duri Prader

The paper gives a short resumé of the findings of the joint US - Swedish "Mechanical Boring (MB) or Drill and Blast Tunneling (DB) ? Workshop" in Stockholm December 1976. New developments and trends in both MB and DB techniques in Europe since 1976 are described, and information is given on some interesting new projects. Differences in contracting principles between the US and Europe lead to different practices for preinvestigations, design, excavation and arbitration and legal affairs. It is shown that this often leads to a higher cost in the US than in Europe for similar excavation jobs. A typical US tunnel job also has more men on the site than a similar job in Europe. This adds to the cost difference and is only partly balanced by a slightly higher rate of excavation in the US. A comparison is made between two quantitative methods of predicting MB penetration rates. These are in reasonable agreement. A probable future development in machine design is an increase in cutter load towards perhaps 25 tons per disc where the tunnel diameter is large enough to house the machine size dictated by the size of the very large electric motors required. Recent European developments in drill and blast technique include improved methods for cautious blasting, precision hydraulic drilling of small diameter holes, and non-electric interval blasting techniques. These developments still keep the drill and blast method ahead of mechanical boring costwise for tunnels in igneous rock whereas for most sedimentary materials mechanical boring has a lead, particularly for long tunnels.

Jan 1, 1979

Bolivia, due to its turbulent past with a history of constant military coups, has given an image of complete instability to the foreign investor. The effects of this have been several fold, the major one resulting in a complete lack of exploration in modern terms since their revolution in 1952. What was overlooked by the foreign investor was the fact that revolution produced Agrarian Reform which is the foundation of the stability which Bolivia enjoys today. Another factor that is overlooked is the fact that its past history is one of vast mining fortunes having being made. Their political problems resulted in economic chaos in 1985 with an annual inflation rate of 26,000 percent. This resulted in the collapse of the government but the democratic process continued. Then came the so-called"South American Miracle" in 1986 when the government of Dr. Paz Estenssoro enacted an extremely harsh austerity program which consisted of the abolition of wage and price controls, the abolition of monopolies, the right to hire and fire, the weekly auctions of dollars and the free convertibility of currency which yielded a stable government with 8 percent inflation. This was followed by massive personnel reductions in the various mines and other industries.

Jan 1, 1991

GARY STUBBLEFIELD RMCMI PRESIDENT 1993-1994 on behalf of the RMCMI Board of Directors and Officers of The Rocky Mountain Coal Mining Institute cordially invites you and your family to attend the 90th Regular Meeting and Convention June 26 thru 28, 1994 Snowmass Resort, Colorado

Jan 1, 1993

By Djk Arentsen

A new technique to drive tubular piles by impact hammer inside the pile has confirmed a dramatic reduction of noise and the opportunity to save steel. Also a reduction in driving time and a higher bearing capacity has been observed during a test program of this technique. As part of the so-called "Down-the-hole" driving technique, a wave equation analysis has been developed to calculate driveability and pile stress. The main feature of the new "Down-the-hole" technique is the development of a patented device allowing uncoupled penetration of pile tip and pile shaft, which makes it possible to drive both closed or open end piles and reduce the stress level induced in the pile wall. During a test program, a number of instrumented piles were driven and compared with traditional driving of the same pile with the same hammer on top (also instrumented). Also the stresses and performances were compared with precalculations. This paper, explains the technique and presents the test and noise results, in comparison with traditional top-pile-driving. The "Down-the-hole" driving technique is an interesting alternative for special applications where traditional pile driving requires a large wall thickness or in areas where noise is a hot item.

Jan 1, 1996

Jan 5, 1976

By Nairin J. D, Hayes P. C

Detailed studies of the microstructures and compositions of zinc and lead blast furnace sinters have been undertaken. An analysis of the results obtained has indicated that in many cases the microstructures of these complex materials can be explained by the solidification of melts from pseudo-ternary phase systems. Further laboratory studies have been carried out to more accurately determine the extent of primary phase fields and the liquidus temperatures in the appropriate binary and ternary systems. This approach shows considerable promise in simplifying the descriptions of slag systems used in oxidising and reduction smelting processes for lead and zinc recovery.

Jan 1, 1992

By Theodore W. Vogelpohl

Augered cast-in-place piles have proven to be effective, adaptable and economical for projects throughout the Ohio River Valley. Specifically, they have been used extensively for high-rise structures, sports stadia and large commercial developments along the Cincinnati, Ohio and Northern Kentucky Riverfront. They have been designed and utilized as relatively short toe resistance piles in bedrock, and intermediate to long toe and shaft resistance piles in granular outwash deposits above the bedrock. They have been designed for large axial compression loads as well as moderate axial tension loads and lateral loads. This paper presents a few load test results that demonstrate the range of capabilities of augered cast-in-place piles in the variable subsurface profile along the Cincinnati, Ohio/Northern Kentucky Riverfront.

Jan 1, 2005

By Charles Pack

DIE castings may be defined as metal castings made by forcing molten metal, under pressure, into a metallic mold or die. It is necessary to keep this definition in mind to avoid confusing this process with other permanent-mold casting processes. The fundamental principles of the process have been known and practised many years. The simplest application is embodied in the modern linotype machine in which molten metal (usually tin-lead alloy) is forced under pressure into a metallic mold. The pressure is derived from a piston and cylinder immersed in the molten metal. Progress in the art of die casting may conveniently be divided into threee groups: Machine for imparting pressure to the metal, material for the die or mold, casting alloys. CASTING MACHINES The problem of delivering molten metal under pressure into a die is comparatively simple, when dealing with low-fusing-point alloys, as the alloys of lead and tin, but it is much more complicated when dealing with metals of higher fusing points, such as the alloys of zinc, aluminum, and copper. Although the art of die casting is comparatively new and, to a large extent, unknown, the records of the patent office are replete with patents on the subject. Fig. 1 shows the Underwood machine patented in 1902; this is probably one of the first machines designed for the production of commercial die castings. The relation of this machine to the linotype casting machine is clearly. apparent. A cylinder and piston are immersed in the molten metal, the application of power to this piston forcing the molten metal, under pressure, into the mold or die. The Doehler machine, Fig. 2, patented in 1907, is based on the same general principles. This machine is used to a large extent at the present time, throughout the United States, for the production of zinc, tin, and lead alloy die castings.

Jan 2, 1919

By Pollard DM, Willis GM

The removal of bismuth from liquid copper in a vacuum furnace was studied over a range of pressures. The rate determining step changes from diffusion in the gas at pressures above 0.2 Torr to approach the Langmuir evaporation rate at pressures of 10-2 Torr. Oxygen and sulphur were found to have a negligible effect on the rate. Bismuth removal from copper sulphide was found to be considerably slower than from copper. This is consistent with the known thermodynamic properties of ternary sulphide melts.

Jan 1, 1980

By Betty M. Miller

INTRODUCTION In September 1974 the Resource Appraisal Group of the Branch of Oil and Gas Resources, U. S. Geological Survey, was asked to aid the Federal Energy Administration (FEA) in its legal responsibility to generate by June 1975 an independent appraisal of the undiscovered oil and gas resources of the United States, both onshore and offshore. As a result, the Resource Appraisal Group accelerated its ongoing efforts to develop sound appraisal methods and procedures that would permit the systematic collection and evaluation of basic data from petroleum provinces throughout the Nation. The results of this independent appraisal of the Nation's conventional oil and natural gas resources were published by the U. S. Geological Survey as Circular 725, June 1975 (1). The estimates in this report of undiscovered recoverable oil and gas resources for the United States were made: (1) by carefully re- viewing a large amount of geological and geophysical information gathered on more than 100 different provinces by over 70 geologists within the Survey; (2) by applying a variety of resource appraisal techniques to each potential petroleum province; and (3) by application of subjective probability procedures to group appraisals for each petroleum province. These methods provide a range of estimates which are summarized in terms of low, high and mean values for the various provinces and groups of provinces, or regions. The basic data and procedures used are documented and are being incorporated into a dynamic, data- intensive system that can be upgraded, updated and reevaluated periodically. These data are open to public inspection. In this study, the primary emphasis was placed on conventional crude oil and natural gas in the onshore provinces and the provinces on the continental shelf out to water depths of 200 metres; estimates

Jan 1, 1977

By Lee H. G, Li H, Hayes P

Slag from the smelting of lead can contain up to 20 per cent zinc as an oxide. An understanding of the lead smelting process and of the subsequent fuming process for the recovery of zinc is enhanced by a knowledge of the activity coefficient behaviour of zinc oxide in smelting slags. The literature presents a wide range of contradictory values. This paper critically reviews the published data and outlines new measurements being made by the authors. A consistent set of zinc oxide activity coefficient data is presented for liquid slags within the ZnO-'FeO'-CaO-A1203-SiO2 system, through a combination of present and previous measurements.

Jan 1, 1993

By Jennifer Gallagher

The Henderson molybdenum mine, near Empire, CO, has operated since 1976 using a panel caving process and a rail haulage transportation system. After two decades of service, the rail haulage system required a substantial capital expenditure to improve operations. The timing for this worked well because Henderson was able to combine this capital need into a mine plan that addressed process bottlenecks and current mining practices as a new production level was designed and developed. This process was a logical step, following an equipment upgrade program, and became known as the Henderson 2000 project. One of the key components of Henderson 2000 is a new ore transportation system. Throughout Henderson's life, the bottleneck has been the rail haulage system. Henderson staff evaluated several transportation alternatives and decided on a truck haulage configuration feeding an underground crusher and conveyor system. This configuration will eliminate the haulage bottleneck and will allow the mine to increase capacity. The installation of this system will be completed by the year 2000. The second key component of Henderson 2000 is the development of a new 7175 production level to extract the lower reserves of the ore body. Henderson staff benchmarked other caving operations and compared their mining practices to Henderson's basic mining guidelines. It became apparent that Henderson's practices could become more efficient, particularly in the areas of drawpoint spacing and column heights. These concepts were incorporated into the layouts

Jan 1, 1998

By A. G. Starliper, H. Kenworthy, A. Ollar

Vapor pressure determinations were made on synthesized germanium sulfides. Germanium and cadmium were removed from sphalerite concentrates by fuming. The fume was retreated to separate some of the cadmium from the germanium and, at the same time, upgrade the germanium to more than 5 pet content. MANY sphalerite concentrates contain certain impurities which have economic value as byproducts. These may include the volatile sulfides of germanium, cadmium, and lead. The objectives of the research reported in this paper were to study the fundamental volatility characteristics of germanium sulfides, to increase the recoveries of ger-

Jan 1, 1957

By S. E. Khalafalla

The Bureau of Mines investigated the metallothermic reduction of copper oxide as a function of temperature, reactant proportions, form of reductant, and gaseous environment, using iron and steel scrap reductants. The reaction proceeded rapidly with powdered iron at temperatures above 560° C, attaining over 95 percent copper metallization within 3 hours. The importance of inter-reactant contacts on the extent of the reaction was evident from the variable, but usually lesser, degree of metallization obtained with iron from tin cans and automobile steel scrap. Reduction decreased as the molar ratio of copper to iron increased between 1 and 3. The most favorable gaseous environment for the reaction was a static helium atmosphere containing about 0.6 percent water vapor. Ferrothermic extraction of copper from its oxides appears to be essentially a "solid-state cementation" process. While ordinary cementation processes must be preceded by leaching, the ferrothermic method avoids this generally slow step and also the water pollution caused by the leaching agents. Sulfidic copper concentrates could likewise be reduced with metallic iron following their complete oxidative roasting.

Jan 1, 1969

By Juan Carlos Valle Morales

El presente texto señala el concepto de la Inteligencia de negocios aplicado a las empresas actualmente, donde se plantea un enfoque estratégico de cómo emplear la información para dar significado, crear conocimiento y tomar decisiones en la empresa minera. Así también se muestra el entorno web que permite generar reportes de indicadores claves mineros con el fin de mejorar el desempeño de la empresa, y consecuentemente reducir sus costos y ampliar su margen de utilidad.

Sep 12, 2011

By Michael J. Mankosa

Increased emphasis has been placed on recycling consumer and industrial waste products. This trend has created a new industry that is focused on recovery/ separation of byproducts from waste material. As a result, interest has increased in the development of separation systems designed for the recycling industry. Much work has been done in this area. However, existing techniques developed for minerals beneficiation are often ignored. An example of is the foundry industry. There are currently more than 3,000 foundries in operation throughout the United States. Each consumes between 9 and 900 t/d (10 and 1,000 stpd) of sand for mold production. Either silica, chromite or zircon is, used in various combinations with chemical or clay binders. After casting, the sands are typically discarded into a landfill. This practice has become an environmental concern, especially the disposal of chromite and zircon. Silica sand is not environmentally sensitive. But it is used in greater abundance (6 to 7 Mt/a or 6.6 to 7.7 million stpy)and thus has prohibitive haulage and landfill costs. Current technology for sand reclamation involves thermal treatment to remove residual binders followed by dry mechanical attritioning (Leidel, 1993; Klein, 1994). This approach results in high losses due to fines generation and high costs associated with thermal treatment. As a result, this approach has shown only limited success. Stringent regulations are also affecting the disposal of secondary materials, such as plastics and metals. This is particularly true for the ferrous and nonferrous scrap metal industry. It plays a major role in industrial recycling of steel, aluminum and copper. Applications such as wire recycling present challenging problems since a hazardous byproduct (plastic insulation) is generated by the recycling.

Jan 1, 1997

By B. Fitch

This paper deals with the behavior of sedimenting suspensions. More particularly, it treats, in as organized a manner as possible, the body of knowledge, theoretical or empirical, by which one predicts the behavior of miscellaneous swarms of particles in suspension. Such knowledge is necessary for precise and economical design of equipment. While the behavior of a single spherical particle settling through an infinite sea of quiescent fluid is well understood, practical sedimentation processes are almost always concerned with particles of assorted sizes, densities, and shapes, in such concentration that there is profound particle interaction. Such swarms of particles are observed to settle in any of four markedly different manners. Which one they follow is governed by particle interaction. It is determined largely by the dilution of the suspension, and the relative tendency of the particles to cohere. TYPES OF SEDIMENTATION The relationship between the different modes of sedimentation is shown paragenetically in Fig. 1. The left side of the diagram represents particles having little tendency to cohere; the right side represents particles for which interparticle cohesion is large compared to the settling force. The vertical axis represents dilution. As seen in the diagram, sedimentation is divided into three broad fields or regimes. At high dilutions there exists a regime here named 'clarification.' Particles in clarification may settle either individually, or by collecting into separated floccules. Thus there are two different possible modes of settling in the clarification regime. It is characteristic c~f this regime that there will be no clear line of demarcation between settling suspension and a supernatant. Faster particles settle out ahead of slower ones. In batch tests there develops a gradation of both particle sizes and pulp density due to progressive depletion of the largest particles from any given pulp level.

Jan 1, 1962

By J. Elmer Thomas

The evolution of the oil business is one of the great industrial romances of modern times. First used as a medicine, then as a lubricant, then as an illuminant, and finally as a motor fuel, each change in its principal usage caused large increases in consumption. Producing Successes The producing branch of the industry responded ably to the demands made upon it. Never was there a famine, rarely any threat of scarcity, and stored inventories were gradually accumulated to form comfortable working stocks. Originally an erratic and hazardous undertaking, the discovery and development of oil fields has made such strides as to classify now as a science. When storage stocks were low, production in close balance with consumption, and demand trending sharply upward, considerable concern was expressed over future needs. Price was very responsive to fluctuations in supply under those conditions, and quotations for crude and refined oils exhibited wide swings. A very different situation exists today. Consideration of the statistics only since the war will show how recent has been this change. In the 10-year period from 1918 to 1927 inclusive, we produced in the United States 6,100,000,000 bbl. of crude and imported 900,000,000 bbl., our total supply being 7,000,000,000 bbl. The consumption was 6,600,000,000 bbl., thus adding to stocks 400,000,000 bbl., an accumulation of somewhat less than 6 per cent. of the total supply. During that period virtually every field was promptly developed as soon as discovered and nearly every well in the country was producing at full capacity. With the maximum production of the wells required to take care of the rapid increases in consumption, with storage stocks moderate and proven reserves very slight, the producing division of the industry acquired a tempo not needed now. Potential Surplus Today the situation is vastly different. The economic consumption is about 2,700,000 bbl., with current production slightly in excess of that.

Jan 1, 1930

By André Xavier, Edim Bahamonde

En las últimas décadas ha habido un aumento del otorgamiento de concesiones mineras por parte del Estado peruano; sin embargo, paralelamente se ha incrementado el número de conflictos sociales. Ante este panorama, es necesario promover la participación de las comunidades a través de la conformación de comités de monitoreo ambiental participativo, como una herramienta que fortalezca las relaciones de confianza entre las empresas mineras, las comunidades y el Estado, de manera que se genere progreso en la línea de los Objetivos de Desarrollo Sostenible. Este estudio presenta los casos de los comités de monitoreo ambiental participativo de Orcopampa (Arequipa), Juprog (Ancash) y Mallay (Lima), como referentes de buenas prácticas que aportan al mejoramiento de la prevención de conflictos socioambientales.

Sep 20, 2019