Search Documents

By Dallas Grubbs

Agenda ?Growth Projections ?Economic Indicators ?Mining Equipment Growth ?Tire Supply ?Michelin Actions to Increase Capacity ?Michelin?s Challenges & Recommendations

Jan 1, 2006

By H.E. Brauer

Among the zinc base alloys used for casting in metal moulds, pnrticularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortncss which facilitate ca,sting. Objection to the use of these alloys may be raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intererystalline corrosion. In all cases which have come to our kno~vlcdge where the conditionsof service were known, failure has occurred upon cxposurc to moisture and heat varying from a hot moist atmosphere to lligh pressure steam. RIoreover, the alloys described in all such roses contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intererystalline oxid:~t'ion in zinc-aluminurn alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Baucr2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the must part, and Rawdon's3 examinations were madc on an alloy containing 0.1 per cent. lead also exyosctl to thc Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to det'ermine the exact nature of this phenonienon and the effect of other metals present as impurities or intentional additions in accelerating or retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation. At the time this work was undertaken the best available equilibrium *Investigator, Metal Section, Research Division, The New Jersey Zinc Company. 'H. W. Williams—Jour. Am. Inst. of AIet,als, Vol. 11, p. 221 (1917). 2o. Bauer—ZeiL, fiir i'vletall Kunde, Vol. 12, .No. 7, pp. 129-31 (1920). 3H. S. Rawdon—Trans. Am. Elcctrochcmic.al Society (1921).

Jan 1, 1923

By Jian Li, Tiejun Chun, Jian Pan, Deqing Zhu, Vinicius Mendes

"A study of the coal-based direct reduction behaviors of composite binder magnetite pellets was carried out in a simulating coal-based grate-rotary kiln process. It is shown that preheated pellets possess much better reducibility than fired oxide pellets: 40 min are required for preheated pellets to reach over 90% metallization degree compared to 100 min for fired oxide pellets. The compressive strength of preheated pellets decreases dramatically at the earlier stage of reduction, climbs quickly after reducing for 30min and achieves a high value at the end of reduction. However, the compressive strength of metallized pellets from reducing of fired pellets is much lower, more cracks and fractures being formed. In the preheated pellets, crystallite of metal iron is coarse. In the oxide pellet, a large number of interconnected crystals of metal iron are formed inside pellets, and pellet structure is very compact.IntroductionDirectly reduced iron is an excellent feed in electric arc furnace (EAF) steelmaking, and possesses low tramp element content and steady component. It is generally preferred in the production of high quality steel [1-3]. Nearly 64.44 million tons of DRI were produced in 2009 over the world, over 80% of which were produced by gas-based processes, the left by coal-based processes. However, the DRI capacity was only 600 thousand tons in China in 2009. The EAF steel production has exceeded 40 million tons annually, and most of EAF operate on hot metal as feed [4]."

Jan 1, 2011

Pictured on these pages are the eight RMCMI Scholarship Award Winners for the 1989-1990 year followed by a brief profile. All winners, except Emmet Roache from New Mexico, were present as guests of the Institute at the June convention in Steamboat Springs, Colorado to receive recognition at the Welcome Session Monday, June 25, 1990. Each state vice president served as the host for the collegiate winner. In addition to receiving a plaque from the Scholarship Chairman, Dr. Donald Gentry, each winner receives $750 tuition credit for the coming academic year. As this is a continuing award, the winners from the previous year will receive another $750 for tuition credit in their senior year if they have maintained good academic standing and are recommended by their university. Criteria for these awards to be made in the spring annually is (1) That the award be made to a sophomore student and used as tuition during the junior year. (2) That the recipient be both a U.S. citizen and a resident of the state involved. (3) That the recipient have good academic standing, be pursuing a degree in a mining related field and have an expressed interest in Western coal as a possible career path. The scholarship program includes curricula other than those in the mining departments, but in the engineering disciplines, such as geology, mineral processing and metallurgy. Contributions to this worthy project are tax deductible to each individual RMCMI member or his firm. Through annual donations of $100 or more, the Patrons of the Institute fund the scholarship program, and the various vice presidents contribute the travel expenses to conventions for these outstanding young collegiates. Donations to this worthwhile program may be made payable to RMCMI Scholarship and mailed to the RMCMI Office, 3000 Youngfield Street, Suite 324, Lakewood, CO 80215. Profiles of the 1990 Scholarship Winners follow. [ ] Mildred Benally University of Arizona Tuscan, Arizona Mildred has attended San Juan College in New Mexico, and will graduate from the University of Arizona in May, 1991. Upon completion of her, schooling she hopes to pursue a career in the coal mining industry. In preparation for her goal, her work experience includes being a lab technician, a mining engineer intern, and a lab technician assistant; she also is very skilled in various computer applications. She has been a member of SME-AIME, and secretary to the U of A Student Chapter, and recipient of the SME Coal Division Scholarship and past recipient of the Navajo Tribal Scholarship. [ ] Joshua Olmsted Colorado School of Mines Golden, Colorado Josh is a sophomore majoring in mining engineering at the Colorado School of Mines. He is an outstanding student as well as an accomplished athlete. Josh was on the Academic Honor Roll 1988-1989 and has been awarded an athletic scholarship. He plays varsity soccer and intramural basketball.

Jan 1, 1990

By C. R. Edwards

"Equity Silver Mines Limited, Canada's largest silver mine, has designed, built and operated a leach plant to reduce the levels of antimony and arsenic in its silver-gold-copper flotation concentrate. The orebody contained deleterious antimony and arsenic minerals in such proportions that the economic long-term sales contracts necessary to obtain project financing could not be procured. Construction of the leach plant therefore allowed development of the mine to proceed. Although the plant took some time to reach design throughput and product specifications, due to the complex and unique nature of the operation, these goals were successfully met and surpassed. This paper describes the physical plant and/or process technology modifications made to mold the main processes-concentrate leaching and filtering, autoclaving and filtration of by-products, and crystallization of salt cake-into an effective, economic operation.IntroductionEquity Silver Mines Limited, a member of the Placer Development Group, owns and operates an open-pit silver mine and related facilities located 37 kilometres southeast of Houston in north-central British Columbia. The mine occupies a 44 I-hectare (1089 acre) site at an elevation of 1300 metres (4265 feet) on the Nechako Plateau. Producing a copper concentrate containing high values of silver and gold, it is the largest silver mine in Canada and one of the largest in the western world. Equity stresses open communications, positive motivation, and production with safety, and achieved the best mine safety record in western Canada in 1984."

Jan 1, 1985

By Chaz Weaver, James Sheahan, Michael Mo

"The Virginia Department of Transportation (VDOT) undertook a program to replace four bridges along approximately 4 mi (6.4 km) of US 340 in Northwest Virginia. Two of these bridges, which span Compton Creek and the Norfolk Southern Railroad respectively, are the subject of this article. HDR provided roadway and structural design as well as geotechnical engineering services for the Norfolk Southern Railroad Bridge while their subconsultant, Saeed Associates, provided structural engineering services in support of the HDR roadway and geotechnical team for the Compton Creek Bridge.The project is located in the Valley and Ridge Geologic Province of Virginia, on an alignment that is adjacent to the Shenandoah River. The project lies within the Beekmantown Group consisting of limestone and dolostone that are prevalent and prone to karstic activity in a band that passes through the project area and north into Central and Eastern Pennsylvania. This area has been impacted by karst limestone conditions where caves and sinkhole activity is common. Caves at Luray and Front Royal, located to the south and north of the project, respectively, are popular public attractions.Since the potential for variability of subsurface conditions can be, and often is, greater in karst terrain, the need to develop a design that provides as much flexibility as possible during construction, and then to be prepared to efficiently review and respond to construction questions is heightened. Coordination and communication among the design staff, VDOT’s design and construction staff, and the contractor was a key factor in completion of this project.Compton Creek BridgeThe alignment for the new Compton Creek Bridge is located about 125 ft (38 m) west of the existing bridge, placing it between that bridge and the existing Norfolk Southern Railroad Bridge. No information about the foundations was available for the existing bridges. Borings in the Compton Creek valley encountered extensive voids (some clay filled and some open) with numerous boulders, rock ledges and pinnacles, particularly on the north side of the creek. Geophysical and geotechnical investigations indicated that below a poor and variable upper zone of rock was a layer of more competent and consistent limestone, which appeared to contain little or no voids."

Jan 1, 2017

By P. C. Lightfoot, J. M. Duke, A. J. Naldrett

"The segregation of magmatic sulphides from mafic and ultramafic silicate magmas, in many circumstances, leaves the magma with a lower-than-normal Ni/MgO ratio, which is characteristic of both lavas erupted from the magma chamber and olivine crystallizing within it. Two end members of the segregation process are discussed; i) batch segregation and ii) fractional segregation.In the former, the critical factor is the magma/sulphide ratio. Computer modelling suggests that where this ratio has been less than 1000, the magma will be recognizable as anomalously low in Ni, due to sulphide segregation, and thus a good target for exploration. In fractional segregation, the critical factors are the proportion of sulphide to silicate being segregated and the degree of fractionation.Samples believed to represent the liquid portion of komatiitic lava f lows from a series of unmineralized sequences in the Abitibi greenstone belt, Canada. Belingwe belt, Zimbabwe, and Barberton Mountainland, South Africa coincide with the sulphide-free fractionation model. They are in marked contrast to samples from the ore-bearing districts of Kambalda and Scotia. Western Australia in which distinct Ni depletion, corresponding to fractionation of olivine plus sulphide in a ratio of between 100 and 200:1 is recognizable. Ni-depleted olivines also mark the sulphide-bearing Dumont intrusion of the Abitibi belt.The Moxie intrusion of northern Maine has distinctly Nidepleted olivines, as does the nearby and petrologically related Katahdin body. In both of these intrusions, the composition of the olivine allows reasonable predictions to be made of the Ni tenors of sulphide showings within them. At Katahdin, the Ni depletion is so widespread that little hope is help out for the presence of economic concentrations of sulphide. At Moxie. the olivine compositions suggest that the best chance of economic sulphides lies in the southern lobe of the intrusion.Ni-depleted olivines also characterize certain rock units within intrusions of the Insizwa complex, Transkei, Southern Africa. Many millions of tonnes of Ni have apparently been removed by sulphides from these rock units, many more than are contained within the single mineralized occurrence so far identified at Waterfall Gorge."

Jan 1, 1984

Computer programs commonly used to simulate mining operations generally require a fair amount of data. The common data input methods have been by either creating an ASCII data file or answering numerous questions during the data input phase. Both methods of data entry are tedious, time consuming, and inflexible. A screen handling system has been developed to drive FORTRAN-77 application software for the MS-DOS environment. The system utilizes keyboard functions with an aid of extended ANSI codes. It also allows a multi-view input data entries.

Jan 1, 1990

By Brian Fulcher, Matthew Bartlett, Jarrett E. Carlson

This paper discusses the challenges to complete the construction of two large underground Metro stations and connecting tunnels in the Tren Urbano system. The completion work includes the installation of specialized mechanical and electrical systems, extensive architectural finishing as well as coordination with systemwide power and controls installed by others. A unique feature of this project was the simultaneous design and construction of the structural/civil/architectural/mechanical/electrical works by KKZ separately from the power and control systems under the management of the Owner, its consultants and other contractors. Completion of this project comes after almost six years of continuous design and construction in a dense urban environment. The project was confronted by many challenges that could only be met with the combined efforts of the Joint Venture team in close cooperation with the Owner and its System wide Contractor. This paper will also address many of the major design and construction changes implemented to suit the Owner’s requirements.

Jan 1, 2003

By Thomas L. Barkley

"In early 2015 the Seed Waveform method was used to measure the Geologic response of the MesabiIron Formation to explosives energy input. This single charge wave form was then used to design acritical first blast at a newly developed Taconite mine. This initial blast had several irregular restrictions on design and performance. It had a very unusual “Frying Pan” shape, the regulatory agency required that no fly rock land in State owned waters less than 200 feet (61 m) away, there was no open face to blast to. Design criteria included the need to detonate the blast with two sinking cuts, and have the sinking cuts meet through a narrow neck between the cuts. All these had to be met using a 16 inch (406mm) diameter hole."

Jan 1, 2016

By S. P. Sandoval

In 2002 the Freeport-McMoRan Technology Center undertook research to develop a lower-cost alternative to guar for cathode smoothing in copper electrowinning. The work was conducted at the Technology Center?s SXEW Test Facility located in Morenci, Arizona. Bench-scale copper electrowinning cells were designed and implemented to screen a number of potential polymers for cathode smoothing. These included modified polysaccharide polymers that were nonionic, cationic, and anionic in nature.

Jan 1, 2010

By A. G. Smelley

As part of research conducted in its mission to effect pollution abatement, the Bureau of Mines, U. S. Department of the Interior, is developing a dewatering technique that allows for disposal of phosphatic clay wastes, for reuse of water now lost with clays, and for reclamation of mined land. The technique utilizes a high-molecular-weightnonionic polyethylene oxide polymer (PEO) that has the ability to flocculate and dewater phosphatic clay wastes. A synergistic flocculation study was made to determine whether a portion of PEO could be replaced by other reagents. Several groups of reagents were tested: (1) those that increased the zeta potential of the phosphatic clay wastes; (2) those capable of hydrogen bonding; and (3) those which flocculated the phosphatic clay waste. Reduction in PEO consumption occurred only with addition of those reagents able to flocculate the slime. The use of natural guar gums resulted in a lower PEO requirement and also yielded a dewatered product of higher solids content, 43 to 45 percent, versus 33 to 35 percent obtained with PEO alone.

Jan 1, 1980

[Abad. Leopoldo F., Min. Engr., Div. of Mines, Bureau of Science Manila, P. 1. '28 Abadilla, Quirico A., Geol., Lago Pet. Corp Box 172, Maracaibo, Venezuela. '20 Abarquez, Ramon F., Met., Bureau of Science Manila, P. I. '24 Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio. '21 Abbott, A. N., Mines Supt.. Mazapil Copper Co,, Ltd Concepcion del Oro, Zac,, Mexico. '28 Abbott, Clarence E., Mgr,, Mines & Quarries, Tenn, Coal, Iron & R. R. Co., 1242 Brown Marx Bldg,, Birmingham, Ala. '04]

Jan 1, 1928

By E. P. Carman

In this report, the Federal Bureau of Mines presents a summary of the occurrence, properties, and uses of some natural bitumens, using the layman's or dictionary definition of bitumens - that is, naturally occurring hydro-carbons. Emphasis is on the less common solid and semisolid bitumens, particularly those occurring or used to some extent in the United States. This comprises data from many sources and references to these sources for more detail than is given in this summary. This paper was prepared primarily to answer questions about some of the less known bituminous materials. The word hydrocarbons could just as well have been substituted in the title for bitumens, but bitumens was used, since an abstract of the paper was presented at a meeting where the major emphasis was on bituminous materials. The reader will realize that coals, of which only the more unusual such as the cannel coals and torbanites are discussed in this paper, are primarily mixtures of bituminous materials and carbon. The amount of bituminous material, or volatile matter, in coals is greatest in the lower rank coals and the unusual types described in this paper, and decreases as coal rank increases. However, since no method other than destruction of the original coal substance by heat is known that will separate the volatile matter from the carbon, it appears reasonable to classify the coals with other bituminous materials, particularly since bituminous coal - the most widely used coal - by its name indicates the combination of bituminous materials and carbon.

Jan 1, 1961

By Robert W. Waytulonis

The mining regulations of all 50 States were reviewed by the Bureau of Mines, and those parts pertaining to the use of internal combustion (IC) engines (particularly diesel engines) in underground mines or confined spaces were extracted. Also extracted were subjects associated with the use of IC engines; for example, storage and handling of flammable liquids, maintenance, and ventilation requirements. As the laws now stand, 29 States have specific regulations that affect the operation of diesel engines in underground coal and/or metal and nonmetal mines. The other States have no regulations because either they have no mining activities or they defer to Federal regulations. Six states have regulations expressly prohibiting the use of diesels in underground coal mines. Specific contacts (addresses and phone numbers) precede each State's regulations to facilitate inquiries about regulation revisions and interpretation.

Jan 1, 1981

The Douglas mineral sands deposit is located 75 km north of Hamilton in western Victoria, Australia. The deposit was discovered in the late 1990s by Basin Minerals Limited and purchased by Iluka Resources Ltd in 2002. Prestrip mining commenced in December 2004, with ore mining commencing in August 2005. Douglas is the first of several projects being implemented by Iluka Resources Ltd in the Murray Basin, with all heavy mineral concentrate planned to be treated at the companyÆs mineral separation plant in Hamilton. The mineralisation at Douglas lies along the south-eastern margin of the Murray Basin. It is hosted by marine Pliocene Loxton-Parilla Sands and consists of three discrete deposits; Bondi Main, Bondi West and Bondi East. The mineralised sediments dip at a low angle to the west and lie unconformably beneath a veneer of top soil (50 - 100 mm) and subsoil (up to 600 mm) and between three to 12 m of overburden. The barren overburden, characterised by high clay content (<53 ¦m material) generally provides a stark contrast to the sandy ore, which is between 1 m (parts of Bondi East) and 15 m (Bondi Main) thick. Both overburden and ore are removed utilising standard dry mining techniques using both scraper-bulldozer and truck-excavator combinations. All ore is delivered to run-of-mine (ROM) stockpiles before being reclaimed by front end loader into the processing plant. Grade control at Douglas is based around visual dig control aided by high precision survey, which enables accurate reference to the resource drilling and block model data. Vertical excavator faces, inclined scraper faces plus regular test pits and trenches provide opportunities for in pit mapping and sampling. This data is used to refine not only the resource estimate for Douglas but also the drilling, interpretation and resource modelling methods used for similar deposits across the basin. The foundations of the geological reconciliation process at Douglas are the in pit surveys undertaken each time the mining fleet has completed building a ROM stockpile. These surveys and the subsequent interrogation of resource models enable robust estimations of the heavy mineral content of the stockpiles, which are subsequently used to predict the daily input grades into the plant during their reclamation. Reconciliation of this daily data is then undertaken at the end of each month against metallurgical production data and plant balances. Learnings and results from the reconciliation process are used to further refine subsequent resource models and modelling methods.

Jan 1, 2009

PRESIDENT HERRES: Our ses¬sions this afternoon will be on safety. They will be under the direction of Mr. Dan Harrington, who has come here from Washington, D. C., particularly to preside at these meetings. I do not think Mr. Harrington needs any introduction to anyone present. He is a member of both the A. I. M. E., and the Rocky Mountain Coal Mining Institute, and has been for a great many years. The Rocky Mountain District is his old stamping ground. I take pleasure in turning the meeting over to Mr. Harrington. (Ap¬plause.) DAN HARRINGTON (Chief Engineer, Safety Division, U. S. Bureau of Mines, Washington, D. C.): Gentlemen, I suppose you have rather a long program, so there is no necessity for any introductory remarks. Inasmuch as I have rather a long-winded paper of my own, I presume the best thing I can do is to go ahead and read it. Mr. Herres asked me some time ago if I would preside here, and also have a paper, or at least have something to say to the Institute on safety. I thought it best to put whatever I had to say in written form, so I would know exactly what I had said and so I would be able to, if necessary, defend it later on.

Jan 1, 1929

By Michael S. Miller

The U.S. Bureau of Mines (USBM) conducted mineral investigations in the 1,227,000-acre Emigrant Trail study area of Nevada during 1992. During the USBM investigation of 25 areas of development interest, 190 mineral localities were identified and 260 rock and 50 alluvial samples were taken. At least 0.5 million troy ounces of gold, 2.3 million troy ounces of silver, 3.3 million pounds of copper, 10.9 million pounds of lead, 2.4 million pounds of zinc, 500 tons of alunite, 40,000 tons of sulfur, 9,000 pounds of mercury, and 21,000 pounds of tin have been mined from the area and vicinity. Adjacent to the study area, gold is being mined at large, open-pit gold mines, the Hog Ranch and Hycroft Resources, Inc., Sulphur mines, and new production is planned at the Rosebud LAC/Equinox. Hog Ranch mine is nearing depletion, but resources of more than 0.5 million troy ounces of gold and about 5 million ounces of silver are estimated for the Rosebud LAC/Equinox project and more than 0.4 million ounces of gold for the Hycroft Resources, Inc., Sulphur mine. Significant investigations are occurring at SP Ridge and other sites near Scossa and at the Dan claims in the Southern Calico Mountains. Precious opal, placer gold, and geothermal energy resources occur in the study area and vicinity.

Jan 1, 1993

President W. K. Dennison, Jr., called the final session of the Rocky Mountain Coal Mining Institute to order, and introduced H. A. Cornell, Portland Cement Association, Ft. Collins, Colorado. Mr. Cornell explained that the Portland Cement Association was not a sales organization, but is supported by the major manufacturers of portland cement. The research laboratories of the association are constantly endeavoring to improve the quality of cement, as well as promote new markets, new uses, and new ideas. The association works with engineers, contractors and universities, making available to them the results of their research. Mr. Cornell stated that numerous booklets and bulletins were available on request for any phase of construction with concrete. Mr. Cornell presented a film, "How to Make Quality Concrete," to the members of the Institute. D. W. Lyke, General Electric Apparatus Service Shop, Denver, Colorado, was introduced by President Dennison, who presented a film, "A-Hunting He Would Go." Following the film, Mr. Lyke stated that his firm was not confined to electrical equipment, but to all types of equipment, and asked the members to feel free to call for assistance at any time. These two films concluded the Manufacturer's Hour, and President Dennison opened the final business meeting of the session. Robert F. Bowie, of the Auditing Committee, read the Treasurer's Report, and complimented Mr. Whiteside on the commendable state in which the books were found. The Treasurer's Report is as follows:

Jan 1, 1960

By H. E. Brauer

Among the zinc base alloys used for casting in metal moulds, pnrticularly die casting, those alloys containing aluminum usually together with copper, are probably the most widely used. The reason lies in their desirable mechanical properties and the fluidity and absence of hot shortncss which facilitate ca,sting. Objection to the use of these alloys may be raised on account of the rather frequent instances of failure of a type variously described as disintegration, exfoliation and intererystalline corrosion. In all cases which have come to our kno~vlcdge where the conditionsof service were known, failure has occurred upon cxposurc to moisture and heat varying from a hot moist atmosphere to lligh pressure steam. RIoreover, the alloys described in all such roses contain impurities or alloying metals which the present authors have found to have enormous accelerating effects on intererystalline oxid:~t'ion in zinc-aluminurn alloys. Thus Williams1 experimented with an alloy containing a large percentage of tin exposed in Cuba. Baucr2 reports failure of a boiler plug containing over 1 per cent. of impurities, doubtless lead for the must part, and Rawdon's3 examinations were madc on an alloy containing 0.1 per cent. lead also exyosctl to thc Tropics. No thorough investigation of the nature and cause of this type of failure has been made heretofore, so far as the authors are aware, although Rawdon correctly classified it as internal oxidation. We have, therefore, carried out this investigation in order to det'ermine the exact nature of this phenonienon and the effect of other metals present as impurities or intentional additions in accelerating or retarding it. In the appendix we include a considerable amount of data which may be valuable in selecting an alloy combining good physical properties with high resistance to oxidation. At the time this work was undertaken the best available equilibrium *Investigator, Metal Section, Research Division, The New Jersey Zinc Company. 'H. W. Williams—Jour. Am. Inst. of AIet,als, Vol. 11, p. 221 (1917). 2o. Bauer—ZeiL, fiir i'vletall Kunde, Vol. 12, .No. 7, pp. 129-31 (1920). 3H. S. Rawdon—Trans. Am. Elcctrochcmic.al Society (1921).

Jan 1, 1923