Search Documents

By C. R. Van Hise

PART I.-GENERAL PRINCIPLES. [ ]

Jan 1, 1902

By J. F. T. Agapito, L. J. Gilbride

High horizontal stresses were recognized to impact roof stability more than 60 years ago. Since then, numerous measurements associated high horizontal stresses with difficult ground conditions. This paper presents case histories illustrating the practical usage of roof stress determinations for helping assess stability, not only in the case of high horizontal stresses but also of low stresses. Examples are given of high stresses associated with faults, mine design changes, quantification of stress shadow effect, and anistrophy. The paper concludes with a comparative evaluation on the effect of various stress fields on ground support requirements.

Jan 1, 2002

The Bowdil Company Bucyrus-Erie Company Card Corporation The Cincinnati Mine Machinery Co. Coal Age Coal Mining Cobre Tire Cummins Power, Inc. FMC Corporation - MHE Division T. J. Gundlach Machine Division/Rexnord Inc. Imperial Oil and Grease Company Ingersoll-Rand Jeffrey Mining Machinery Division, Dresser Industries Inc. Joy Manufacturing Company K&P Sales Engineers, Inc. Kennametal, Inc. Lively Manufacturing & Equipment Co. Long-Airdox Co. MS A McLanahan Corporation National Mine Service Company Distributor Products Division Page Engineering Plateau Supply, Inc. Plymouth Rubber Company, Inc. Pyramid Parts Div./American Alloy TIC - The Industrial Company Tricon Metals & Services, Inc. Uniroyal, Inc. Utah International Inc.

Jan 1, 1985

By Herbert F. ?Buck? Darling

A bridge replacement project in Rochester, NY, encountered difficulties when it was determined that rock below one pier was sloping downward toward the river at an angle of 42 degrees versus anticipated 12 degrees. Cofferdam design and construction became very difficult. The unanticipated subsurface conditions delayed the project by eighteen months and increased the cofferdam cost by almost $3.0 million ($US) when direct costs and associated delays were taken into account. The initial approach after discovery of the problem was to use the same type pier design and modify the cofferdam accordingly. This resulted in a cofferdam 12 meters (39.4 feet) deep on the shore side and 18 meters (59.0 feet) deep on the water side. The design used a master pile system to attain required wall strength and used rock anchors to prevent the cofferdam from moving toward the river. The pier foundation was then redesigned by the owner using revised seismic parameters. The original stepped footing carved into rock was replaced by caissons socketed into the rock beneath a large tremie concrete placement. The revised pier and cofferdam designs caused a shift from a mostly land based cofferdam, excavation, and rock removal project into an almost entirely water based cofferdam, caisson drilling, and tremie construction project. These design changes resulted in a reliable, safe, and unusual cofferdam and construction method. All of this was accomplished within a very narrow worksite with a railroad on one side, and the river with its public and commercial freighter traffic on the other. In addition, the existing two-leaf drawbridge was to be maintained in place which put further limitations on the water borne equipment. The engineering and construction considerations, problems, and solutions related to these cofferdams and pier foundations are presented.

Jan 1, 2013

By Greg Shapiro, Paul Dr. Worsey

Mining, quarry, and construction blasts are becoming more and more dependent on bench profiling. The use of accurate profiling gives the blaster better data for the most efficient blast results. So, we ask the question: What is the best method for measuring and analyzing burden?

Jan 1, 2019

By R. T. Hukki

IT is no great exaggeration to say that present grinding practice and economics are largely determined by lining design. A record of outstanding liner wear can be achieved with any liner surface pattern that will positively lock the outer layer or layers of grinding media. With no slippage, lining wear is bound to be slight. At the same time, popular practice calls for tumbling loads of about 50 pct of mill volume to obtain maximum grinding capacity. Innumerable parallel grinding investigations have verified that optimum speed for such a mill lies within 70 to 85 pct of theoretical critical speed. If the mill is speeded up to 100 pct of critical, little or no grinding can be accomplished. Earlier Work on Supercritical Grinding: First investigations concerning grinding at supercritical speeds seem to be very old. Remarkable work on the subject has been performed by White,&apos; and his experiments have been described and summarized by Richards.&apos; White&apos;s contributions seem to have passed unnoticed by Fahrenwald,2,3 whose extensive experiments have been well presented, yet apparently very little appreciated. Additional work on grinding at supercritical speed has been reported, e.g., by Lewenson and Tscherny,&apos; USSR; Anselm and Grunder,&apos;, Germany: and Rose and Evans." Great Britain. Subcritical and Supercritical Speeds: In the formula of the critical speed given in the textbooks of mineral dressing, no factor indicating the coefficient of friction is generally included. If this factor = 1.0, which is equivalent to grinding conditions in a mill provided with heavily ribbed lining, the formula of the critical speed holds as such and grinding is possible at subcritical speeds only. In a mill equipped with a smooth or relatively smooth lining, the numerical value of the friction factor in the denominator of the formula becomes <1.0, indicating that grinding at supercritical speeds should be possible in such mills. It has been recently shown by the author&apos; that a wide supercritical speed range will become available for grinding—and especially for fine grinding—if the basic conditions within the mill have been selected properly. Mathematical analysis of mill dynamics at supercritical speeds&apos; has indicated that the mill speed may be increased if: 1) total mass of grinding medium decreases, 2) mass of the individual grinding piece increases, and 3) the coefficient of friction between the outer layer of medium and the mill lining decreases. It is obvious that the mass of the individual grinding piece will be affected by its shape and by its specific gravity. The coefficient of friction decreases with: 1) increasing smoothness of liner surface, 2) increasing roundness of the grinding piece, 3) increasing fineness of material to be ground, 4) decreasing pulp density, and 5) decreasing hardness (abrasiveness) of the mineral to be ground. In a mill equipped with heavily ribbed lining, practically no size reduction will take place between the lining and the outer layer of tumbling medium, because slippage is prevented. In the overwhelming majority of today&apos;s mills the grinding accomplished is by virtue of cataracting and/or cascading media with some action within the tumbling charge. Sub-critical speeds only can be applied. In grate-type or peripheral discharge mills equipped with a smooth lining a tumbling load of any kind of common medium occupying about 50 pct of mill volume will behave in such a way that practically no slippage will take place. This has been verified in experiments run by the author in the laboratory and in pilot plant mills&apos; equipped with smooth lining. Again, the operation is limited to the subcritical range. In a mill with a smooth lining, grinding will be possible either at subcritical speeds or within a wide supercritical speed range as soon as the basic requirements for a desired speed are fulfilled. In a mill operated at supercritical speed, any point on the liner surface proceeds at a speed greater than that indicated by the formula of the critical speed, while any grinding piece situated in the outer layer of the medium against the lining proceeds in the same direction at a speed less than that indicated by the critical speed. This speed difference produces a very effective attrition grinding zone between the liner surface and the outer layer of the medium. The share of attrition grinding of the total grinding accomplished increases rapidly with increasing speed in the supercritical speed range. The smooth surface of the mill lining may be well illustrated by the surface of a bucking board. The outer ball layer may be similarly represented by the lower surface of a muller. If the bucking board, the material to be ground, and the muller all proceed in the same direction at the same speed, no grinding will result. This is the general situation in the mills of today. If, however, the muller is pulled with respect to the board, moving or stationary, grinding will be accomplished effectively. Although grinding in today&apos;s mills is primarily the result of cataracting and/or cascading media, the principal place of grinding at high supercritical speeds will be the attrition zone.&apos; In the mineral dressing laboratory of the State Institute for Technical Research. Helsinki, Finland, large quantities of different ores have been ground in a pilot plant ball mill (3x3 ft) at a top speed about 230 pct of the critical. With the same mill, theoretical investigations concerning the grinding characteristics of ball mills equipped with a smooth lining have been carried out up to the speed of 313 pct&apos; of the critical. With a smaller mill, the grinding characteristics with a variety of grinding media have been investigated at speeds up to 2000 pct of the

Jan 1, 1959

The preamble to the mining Act sets out that such Act is to provide for the encouragement and regulation of mining within the State of Queensland. This paper will attempt to follow the legislative path of such aim and in particular to show what part Mining Wardens play in the administration of the Mining Act.The Mining Act empowers the Governor in Council to constitute Mining Districts and Mining Fields and to appoint any duly qualified officer of the Public Service of Queensland to be a Warden or a Mining Registrar. As a matter of practice Stipendiary Magistrates who hold office in the major centre within a Mining District are appointed Wardens and Clerks of the Court are appointed Mining Registrars. In some districts where there is no Stipendiary Magistrate the Clerk of the Court is appointed an Acting Warden with all the powers of a Warden. Every Warden so appointed is a Warden for the whole State.To achieve impartiality Section 74 of the Mining Act provides that a Warden shall not hold or be entitled (directly or indirectly) to the benefits of any share or interest in a mining tenement or mining venture and provides a penalty of $1000 or imprisonment for six months or both, for contravention of such section.

Jan 1, 1986

By Haydn H. Murray, Sam H. Patterson

The term clay is somewhat ambiguous unless specifically defined, because it is used in three ways: (1) as a diverse group of fine-grained minerals, (2) as a rock term, and (3) as a particle-size term. Actually, most persons using the term clay realize that it has several meanings, and in most instances they define it. As a rock term, clay is difficult to define because of the wide variety of materials that compose it; therefore, the definition must be general. Clay is a natural earthy, fine-grained material composed largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates composed mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many definitions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic; for example, halloysite and flint clay. As a particle-size term, clay is used for the category that includes the smallest particles. The maximum-size particles in the clay-size grade are defined differently on various grade scales. Soil investigators and mineralogists generally use 2 micrometers as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than approximately 4 micrometers. Some authorities find it convenient to use the term clay for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or argillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally understood by those who use it. Clay is an abundant natural raw material, and it has an amazing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial minerals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1978, 1979, and 1980 production and values according to the US Bureau of Mines (Ampian, 1980). Statistical data summarizing world production of kaolin, bentonite, and fuller&apos;s earth are compiled by the US Bureau of Mines (Ampian and Polk, 1981). The total world bentonite production in 1980 was 6,625,204 st of which the United States produced 4,184,619 st. The total fuller&apos;s earth produced in the world in 1980 was 1,952,600 st of which 1,534,000 st was produced in the United States. The total world kaolin production in 1980 was estimated at 22,971,000 st. Approximately 13 million tons of this total was produced in two countries, the United States and the United Kingdom. World production data on ball clay, fire clay, and miscellaneous clays are not available. As industrial minerals, clays are a complex group that consists of several mineral commodities, each having somewhat different mineralogy, geologic occurrence, technology, and uses. In this chapter these commodities are organized as follows: (1) bentonite and fuller&apos;s earth; (2) kaolin, ball clay, halloysite, and refractory clays; and (3) miscellaneous clay and shale. Bentonite and fuller&apos;s earth are grouped together because they are closely interrelated. Though bentonite is a term based on mineral composition and fuller&apos;s earth is a term based on use, the two are virtually inseparable, because much, but by no means all, clay sold as

Jan 1, 1983

[A AALSETH, Earl P (M 51) Consult Geol Engr 2019 Eldorado Dr, Billings, Monl ABADIE, Henry G (M 43) Asst to Supt of Oper Long Beach Oil Dev Co 925 Harbor Plaza, Long Beach 2, Calif ABBE, T Waldo (A 56) Asst Dist Oper Supt Sun Oil Co PO Box 66, Stowell, Tax ABBOTT, Fred E Jr (M 59) Abqaiq Dist Mgr Arabian American Oil Co Dhahran, Saudi, Arabia ABBOTT, Clifton T (A 60) Apartado 677, Maracaibo, Venezuela ABBOTT, J L (M 56) Partner Pritchard & Abbott 1010 Ft Worth Natl Bk Bldg, Fort Worth 2, Tex ABBOTT, Richard H (J 51) Partner Abbott & Howard 422 W Hermosa San Antonio 12, Tex .ABBOTT, William G (M 50) Div Mgr Rice Engrg & Operating Inc Box 1142, Hobbs, N. M. ABDERHALDEN, Ronald R (J 59) Prod Engr Continental Oil Co Box 100, Carmi, III ABEL, Malcolm D (J 50) Gen Partner Abel & Bancroft PO Box 865, Midland, Tex ABEL, Ramond L (M 28) Prof of Chem Eng Univ of Pittsburgh, Pittsburgh 13, Pa ABEL, Wayne K (M 57) 1513 Patton Drive, Odessa, Tex ABELL, Joseph M (J 55) Petr Engr Tennessee Gas & Oil Co Box 1772, Casper, Wyo ABELS, Thomas A (J 60) Exploit Engr Shell Oil Co Box 193, New Orleans 3, La ABENDROTH, G F (M 46) Dring Prod Supt Lyons & Logan 1500 Beck Bldg, Shreveport, La ABERCROMBIE, Bolling A (M 60) Mgr Product Planning Axelson-Garrett PO Box 2427, Longview, Tex ABERCROMBIE, C T (160) Prod Engr Cities Ser Petr Co Box 472, Brownfield, Tex ABERCROMBIE, H L Jr (J 55) Prod Engr Mobil Oil Co Room 1800 Gr PI Life Bldg, Lubbock, Tex ABERCROMBIE, Robert (J 57) Prod Engr Mobil Oil Co PO Box 1770 Shreveport, La ABERG, Richard S (M 57) Area Prod Geol Shell Oil Co of Canada, Box 100 Calgary, Alta, Canada]

Jan 1, 1961

By Michael F. Roach, Joseph K. Cavey, Gary E. Taylor

A rigorous horizontal drilling and chemical grouting program was specified beneath the Hollywood Freeway (U.S. Route 101) section of Los Angeles Metrorail Contract C-311.Twin 6.67-m (22-ft.) diameter starter tunnels were to be conventionally mined through amixed alluvial and bedrock face consisting of silty sand, gravel, and weathered sandstone and siltstone of the Topanga Group. The contact between the alluvium and bedrock dipped toward the Crossover Excavation where the horizontal drilling and grouting operations were performed. The intent of this grouting program was to stabilize the mixed face to minimize ground loss and surface settlement, and to reduce groundwater inflow into the tunnel headings. Given the highly variable mixed face conditions, horizontal drilling up to 86 m (284 ft.) resulted in upward trending trajectories which likely followed the bedrock contact. Chemical grouting was performed in a primary, secondary and tertiary, three dimensional sequence. Evaluation of the primary and secondary grouting parameters indicated where tertiary grouting was required. Grouting pressures induced a small rock failure at the tunnel heading as well as increased stresses on the tiebacks of the excavation.

Jan 1, 1997

By Neal M. Miur

"INTRODUCTION The Mineral Ridge-Clay Lick fault system in Crittenden and Livingston Counties, Kentucky, is one of the larger and more important fault systems of the Western Kentucky Fluorspar district. Total production from it up to July 1945 (chiefly since 1900) was approximately 80,000 tons of fluorspar ore, 10,000 tons of which came from the Mineral Ridge Fluorspar Co. tract 1, which was being operated by the Mahoning Mining Co. of Rosiclare, Ill. The fluorspar ore carries lead and zinc that can be recovered by milling, and the Mahoning Co. planned to log-wash the ore at the mine and then mill it in its mill at Rosiclare, The Mineral Ridge Fluorspar Co. properties were examined by O. M. Bishop, an engineer of the, Bureau of Mines, in August 1942. During 1943 and 1314, developments on the properties were under observation by X. B. Starnes, of the Bureau, and it was decided to diamond-drill tracts 1 and 2, as indications seemed favorable for opening up additional fluorspar ore bodies. Drilling was begun March 12, 1945, and was completed July 2, 1945, during which time 12 holed were drilled on tract 1 of the Mahoning Co.'s leases for a total of 3,637.1 feet, and one hole 359 feet deep was drilled on tract 2 of the Jennings lease. The Mineral Ridge-Clay Lick fault system, 4 to 47 feet wide, was encountered in all holes at 126 to 265 feet."

Apr 1, 1947

By I. V. Lunkin, E. B. Muhamedzhanov, A. B. Begalinov, B. R. Rakishev

Almost all the ore deposits of ferrous, non-ferrous and rare metals of Kazakstan, are exploiting by the open-cast method, are the complex-structural, multi-component ones. Their rational working requires precise organization of extracting works. In this connection it is necessary to set up the best intercommunications between drilling-blasting, excavating-loading and transport works. This requires the stable functioning of the quarry for dispatch of ore raw material of required quality with minimum of corresponding expenses. For this purpose, proceeding from the quarry’s ore output and the assumed parameters of the exploitation system, the first problem about rational arrangement of excavating-loading equipment in extracting faces is solved. By solving the problem the model with dynamic, adapting properties had been used. It was solved numerically by the method of statistical tests. By setting up the necessary link between type-sizes of excavating-loading and transport equipment, the minimum prime cost of loading and transportation of 1 ton of mining mass from the face to the receiving station was adopted as the criterion of optimality. Depending on the type of excavating-loading equipment, the efficiency function may be different. By using wheel loaders, their displacement between the faces is possible, therefore, the efficiency function of the problem may include expenses for their displacement. By using excavators like power shovel, the problem’s restrictions must exclude its displacement between the faces. The efficiency function consists of minimum expenses for loading, proceeding from set of volumes of extraction from the faces, satisfying required quality. The volumes of extraction from the faces, satisfying required quality of ore in output stream, are determined by the method of statistical tests. Sample range is given, proceeding from the restrictions for maximum productivity of the excavating-loading equipment. Volumes of extraction, not satisfying required quality, are cut off. The efficiency function meaning is then determined and minimized. Keywords: Excavating-loading equipment, its placing in extracting faces, optimal load-carrying capacity, specific expenses for loading and transportation of mining mass.

Jan 1, 2003

Ground support audits are sometimes necessary in ageing underground mines. Usually, the purpose of such audits is to assess the state of the ground support in various parts of the mine, identify areas that require attention and establish rehabilitation requirements. In 2005, Brunswick Mine, located in Bathurst, New Brunswick, Canada, completed a comprehensive mine-wide ground support audit. The areas examined included excavations in several mining blocks, as well as ramps, shaft stations, garages, shops, etc., throughout the mine. A vast amount of data was collected over a period of two weeks by multiple auditing teams. The audit was followed by a data digitisation exercise, and the creation of a data management system to store audit results and keep track of subsequent rehabilitation activities as they occur. One aspect of the data management system was the incorporation of a function for reporting on ground rehabilitation progress, along with the capability of updating mine level plans for easy visual presentation of this progress. This article describes the approach implemented at the mine to carry-out the audit, as well as the database constructed to manage the results.

May 1, 2009

By S. R. Zimmerley, C. H. Schack

"INTRODUCTION The pilot-mill concentrator at Boulder City, which has a nominal capacity of 40 tons per day, was planned and built to investigate further the beneficiation of domestic manganese ores that have been concentrated successfully in the ore-dressing laboratory. As milling of manganese ores in general is a new field, it is necessary to prove the success of laboratory processes by means of large-scale operations employing standard milling equipment, and thus to obtain engineering and metallurgical data essential to designing and operation of full-scale concentrating mills.The first ore tested in the pilot plant was the Three Kids Annex manganese ore from the Las Vegas Wash area 15 miles southeast of Las Vegas, Nev. The deposit was worked for its high-grade ores during the First World War From 1930 to 1939, 4,500 feet of diamond drilling was completed by a private company. Diamond drilling started by the Bureau of Mines in November 1940 and completed in July 1941 aggregated 6,600 feet. Exploration by the private company and the Bureau outlined reserves of about 1,000,000 tons of ore assaying plus 28 percent manganese. A much larger tonnage of lower-grade ore also was outlined by the drilling.Because of its physical nature, the Three Kids Annex ore had long proved unamenable to concentration by ore-dressing methods. The ore is a mixture of manganese oxides (wad) filling the pores and to some extent replacing a silt composed of very fine grains of volcanic tuff, quartz, feldspars, other silicates, and clay. Some gypsum occurs as fillings along fracture planes. The ore is light and very porous. Upon wetting, it disintegrates into granular but friable particles and a large amount of slime. It is these characteristics that make the ore so difficult to concentrate."

Sep 1, 1947

By Faruk Oksuz, Phillip L. Covell, Martin Doll

A series of difficult ground conditions causing high groundwater inflows and hazardous gas intrusion abruptly halted the construction of a 6.4-meter (21-foot) finished diameter and 1,890 meters (6,200 feet) long tunnel planned to serve as a 4-millioncubic meters (1-billion gallon) per day capacity river outfall for treated wastewater. Some 808-meters (2,650-feet) section of the constructed tunnel, TBM, and all other tunneling equipment were completely flooded with hydrogen sulfide laden artesian groundwater. The subsequent pumping and tunnel recovery efforts were unsuccessful and the tunnel was abandoned. In the end, the construction contract was terminated and options to redesign and reconstruct the project were re-evaluated to maximize the use of already constructed tunnel facilities such as the construction access and inter-mediate shafts and six outfall diffuser shafts in the river.

Jan 1, 2007

By Don M. Coulter

"INTRODUCTION Bauxite, in Appalachian Alabama, occurs in the Rock Run and Goshen Valley districts in Cherokee County; in Nences Creek Valley near Jacksonville; near Anniston in Calhoun County; north of Fort Payne in DeKalb County; near Ashville in St. Clair County; and near Talladega in Talladega County.In February 1942, Preston E. Cloud, Jr., assistant geologist, Federal Geological Survey, began a study of these bauxite deposits and the geology relating thereto.The Bureau of Mines established field headquarters at Piedmont, Calhoun County, in July 1942. Mineral agreements covering a total of 11,097 acres were executed with 15 landowners in the Rock Run district; 38 in the Goshen Valley district, covering 7,575.5 acres; and 3 in the Nances Creek Valley district, covering 988.5 acres. Drilling was done on the properties of 9 land¬owners in the Rock Run district, and on the property of 1 landowner each in the Goshen Valley and the Nances Creek districts. Drilling began October 26, 1942, and ceased on May 17, 1943.Power drilling was supplemented by a labor crew that drilled hand-auger holes in shallow deposits and sampled .old shafts, mines, and mine dumps.In all, 222 holes for a total of 13,250 feet were drilled. Of these holes, 88 penetrated bauxite but too low in grade to constitute ore."

Mar 1, 1948

By P. Tong-jiang

We studied mineralogical characteristics of the vermiculite samples from seven mines in China. We found three types of interstratified structures in the investigated samples: 1:1 regular interstratified structure, segregated interstratified structure, and random interstratified structure. The vermiculite samples from six mines are mainly composed of phlogopite?vermiculite interstratified minerals, and the samples from the other mine are composed of chlorite?vermiculite interstratified mineral. The samples with phlogopite?vermiculite structure have high contents of K2O, TiO2 and Na2O. The samples with chlorite?vermiculite structure have the highest contents of MgO and Al2O3. The cation exchange capacity of the samples is 17.3?99.0 mmol/100g.The exchangeable cations of phlogopite?vermiculite samples from Weili Mine mainly include Na+ and Ca2+, while those of phlogopite?vermiculite samples from Tongguan Mine mainly include Mg2+ and Ca2+. The thermal expansion ratio of the samples is between 9 and 32. The exfoliated vermiculite products from Weili Mine have the best mechanical strength.

Feb 27, 2013

By Michael Ostrowski

While the words “explosives” and “blasting” cause insurers to become apprehensive, skilled contractors using modern techniques under controlled conditions rarely cause serious damage or injury. However, blasting operations frequently result in complaints and, consequently, insurance claims. The purpose of this bulletin is to inform construction project participants of some of the measures which may be taken to reduce losses arising from blasting operations.

Jan 1, 2003

By Ronald B. Stotelmeyer

This report summarizes the U.S. Bureau of Mines evaluation of the mineral resources of eight roadless areas in several National Forests in Montana. The areas are amoung those that have been proposed as additions to the National Wilderness Presevation System In various sessions of the U.S. Congress. Mineral Commodities present include gold (lode and placer), silver, copper, lead, zinc, molybdenum, tungsten, rare-earth elements, fluorite, and barite. Numerous mineral deposit types occur. Past production was from gold placers and vein-type deposits. There is potential for development of large volume porphyry copper-molybdenum, disseminated gold, stratabound copper-silver, and exhalative massive-sulfide metallic deposits. A substantial increase in metal prices is needed before any known vein-type deposits will be economic.

Jan 1, 1994

By Ralph Spickermann

UK Seabed Resources (UKSR) signed a manganese nodule exploration contract with the International Seabed Authority on 8 February 2013 for a 58,000 km2 tract on the eastern edge of the Clarion Clipperton Zone (CCZ). UKSR is a private company based in the United Kingdom and established primarily to develop the commercial potential of the CCZ deposits. This is the first of many anticipated regulatory, market and technical milestones that are requisite for (1) environmentally responsible commercial scale production of nodule derived metals and (2) generation of revenue through their sale in the global commodities market. This presentation will describe the progress made to date in this effort and an industry-based perspective on the tasks and challenges that may lie ahead.

Sep 1, 2014