Search Documents

This paper summarises the influence of slurry rheology on the grinding throughput of batch laboratory and continuous plant-scale mills operating in open and closed circuit configurations. The results of controlled changes in percent solids, particle size, slurry temperature, and viscosity control chemicals are demonstrated. An underlying rheological explanation of the above factors is offered which involves tying the specific rates of breakage that are occurring in the mill with the specific rheological character that the slurry is exhibiting at any given set of operating conditions. Some industrial scale operating guidelines are presented which have proven useful in increasing the net pro- duction capability of grinding circuits.

Jan 1, 1978

By D. Harker, E. Epremian

The constitution of the nickel-tungsten system has been studied by a number of investigators, the most recent of which are Ellinger and Sykes.1 On the basis of metallography, electrical resistivity and hardness measurements and some X ray diffraction work, they constructed a consitution diagram (Fig 1). Ellinger and Sykes report a0 for the alpha face-centered cubic phase (nickel saturated with tungsten) as 3.66?.‡ The gamma phase (tungsten saturated with nickel) is given as body-centered cubic, but no value of a. is recorded. At 43 pct tungsten by weight (approximately 20 at. pct) a beta phase is reported, but structure and lattice parameter are not known. Primarily on the basis of metallographic evidence, they conclude that beta is a new phase and rule out the possibility of formation of a superlattice since they- observe a new phase in the microstructure. Grube and Schlecht2 report an ordering reaction in a system similar to the Ni-W (Ni-Mo) and Harker3 has shown that NirMo forms a superlattice upon the pre-existing face-centered cubic lattice of the alpha phase. Elliniger arid Sykes observed a change in the diffraction pattern of a 4.3 pct W alloy upon aging and attributed it to the formation of a new phase. Thus, there appears to be some question as to the character of the beta phase reported by Ellinger and Sykes. The purpose of the present work is to determine precisely the structure and nature of the beta phase in the Ni-w system of X ray diffraction methods. Experimental Procedure One inch diameter ingots of 43.66 pct, 40.15 pct and 34.06 pct .tungsten by weight (19.8, 17.6 and 14.1 at. pct respectively) were melted and cast under vacuum from electrolytic nickel and pure wire filament grade tungsten. The ingots were soaked for 16 hr at 1300°C in a hydrogen atmosphere furnace, then swaged at this temperature and finally drawn to 0.020 in. diam wire. Some of the bar stock was retained in 1/2 in. diam rod for hardness and metallographic studies. Wire samples for diffraction work were sealed in evacuated quartz tubes and subjected to the various solution and aging heat treatments in a hydrogen furnace. X ray photograms were taken in a Debeye-Slierrer camera using copper K radiation filtered by nickel foil. Results X RAY DIFFRACTION The lattice parameters of the alpha and gamma phases at saturation were determined by an X ray photogram of the 19.8 at. pct W alloy after solution heat treatment at a temperature well within the alpha-gamma range above the peritectoid temperature (17 hr at 1150°C—oil quenched). The alpha phase was found to be face-centeted cubic with a. of 3.594 ± 0.001?, while the gamma phase was determined as body-centered cubic with a. of 3.158 ± 0.001?. Exactly the same phases and parameters were ohtained with the 17.6 at. pct W alloy for the same solution heat treatment. Thorough analysis was made of an X ray photogram of a 19.8 at. pct alloy sample in the quenched and aged condition (solution treated 1T hr at

Jan 1, 1950

In 1980 Pancontinental Mining Limited decided that while the Jabiluka uranium project was still a major focus of the company's efforts some diversification was necessary. At this time it was decided to include precious metals in Pancon's exploration and acquisition objectives. As a result the now Paddington Gold tenements were acquired, explored and developed. Today, it rates as the 6th largest gold mine in Australia and at an expanded throughput of 1.2 million tonnes per year of ore it will produce about 110,000 ozs of gold per year. Following extensive exploration activities by Pancon's Exploration Division the Operations Division continued with development drilling finally proving up a reserve of about 8.4 million tonnes at an average grade of 3.2 g/t. An in- house preliminary feasibility study was followed by a two phase feasibility study by Davy McKee. This resulted in a recommendation to the Pancon Board of Directors to develop Paddington with an annual throughput capacity of 875,000 tonnes. This paper describes the acquisition, exploration and development of the Paddington project. It goes on to

Jan 1, 1986

The Great lady gold deposit presented the challenge of providing a new grade control system for an usual type of orebody in the Eastern Goldfields. Mineralisation occurs as secondary enrichment about a quartz sand - granite saprolite contact 30m below surface. The ore horizon, which averaged 2.5m thickness, was near-horizontally disposed in contrast to the typical steeply dipping, shear hosted deposits of the region. A trial mining operation was undertaken on the richest, most continuous portion of the deposit to test the economic viability of this type of orebody. Controlling and minimising vertical ore dilution was considered crucial to the profitability of the operation.An understanding of the grade distribution combined with the practicalities of mining produced a grade control system which allowed for the mining of 1/2rn composited grades on level lm benches. Ore mining was combined with strict monitoring of levels, truck destinations and ore boundaries. Ore reconciliation results showed this system to be effective.

Jan 1, 1990

By May P. M

The role of chemical speciation in alkaline cyanide solutions is discussed by reference to recent experimental data from the authors' laboratories. It is shown that serious gaps exist in our present knowledge of the thermodynamics of cyanide complexes in solution. Nevertheless, using the available data and the JESS suite of computer programs it has been possible to develop a simplified chemical speciation model for alkaline cyanide solutions under conditions relevant to the gold extraction process. Some possible implications of the model for plant operations are Discussed.

Jan 1, 1991

By E. Lehtila, J. J. Talja, R. Jahila

Kopar Oy is acknowledged for engineering and manufacturing of robust systems for bulk material handling, especially at power plants and non-ferrous smelters. We have over thirty years of experience with systems specifically designed for hot and abrasive conditions, aiming at low cost of ownership, low operational expenses and high availability. Although Kopar has numerous applications in mechanical conveying, there is an increasing number of pneumatic conveying applications at copper smelters. They relate to conveying of concentrate, and primary and secondary flue dusts. Challenges of pneumatic conveying for concentrate are mechanical and do relate to broad particle size distribution and high abrasivity of the concentrate and the silica. Therefore, special attention shall be paid to system design and ceramically lined bends in the pipeline. Challenges of pneumatic conveying of primary flue dust relate predominantly to material stickiness and poor flowability which are mainly due to fine particle size and formation of sulphates and furthermore, crystalline water. Additional challenges of secondary dust, the white converter dust, are primarily due to the extremely fine 0.1–1.5 µm particle size and problems which come with this. Effect of material characteristics like size distribution, morphology and chemical composition in pneumatic conveying are discussed in detail. INTRODUCTION Fine materials like concentrate, feed mix, flue dusts (from waste heat boiler and electrostatic precipitator) and secondary dusts need to be conveyed at smelters. Both horizontal and vertical conveying and combination of those are used. For the purpose, both mechanical and pneumatic conveying are applied. Most widely used equipment are drag chain conveyors and various combination of pneumatic systems, e.g. air lift, dense-phase and dilute phase pneumatic conveyors. Kopar has 30 years’ experience with multiple material handling systems. Furthermore, acquired companies like Elmomet Oy and SITE Oy (both currently fully merged and integrated into Kopar Oy) have even longer history, especially in pneumatic conveying. It is commonly known that the finer the dust the more difficult it is to be conveyed pneumatically. Sulfates with crystal water makes it all even more difficult, if not ineligible. Challenges related to pneumatic conveying of various fine materials is discussed in detail in the paper.

Jan 1, 2019

By H. O. Hofman

The mining and metallurgical laboratory, as we understand the term in this country, is a place .in which mechanical and chemical working-tests are made on ores, fuels and furnacematerials. It is of quite recent origin. The first laboratory of this kind to be used in connection with teaching was put into operation in 1871 at the Massachusetts Institute of Techilo1ogy. † The idea had already existed in the mind of President W. B. Rogers when he wrote, in 1864, his pamphlet 'on " The Scope and Plan of the School of Industrial Science of the Massachusetts Institute of Technology;" but several years elapsed, and an extended visit to the mines and mills of Colorado, Utah, Nevada and California was required before this idea could take a form adapted to the purposes of original research as well as of instruction. The laboratory was given from the first into the charge of Prof. R. H. Richards, who, by improving its methods and enlarging its scope, has brought it to the position which it occupies to-day as the leading representative of its class. Private laboratories for making tests upon ores had previously existed here and there, especially on the Pacific coast, for silver and gold ores; but in the educational field the

Jan 1, 1896

1. PURPOSE The Temporary Face Support System (TFSS) consisting of beams, posts and carrying-emplacing equipment was developed to provide temporary supports between the working face and the permanent roof supports. 2. GENERAL DESCRIPTION The system consists of: ? A Beam And Post Carrier And Deployer (BAPCAD), a self-propelled machine that carries as well as emplaces the beam-and-post sets. ? Lightweight mechanically self-deploying posts designed to safely support a load of 10,000 pounds each. ? Lightweight constant strength beams (bars) capable of sustaining an approximate equally distributed load of 8500 pounds. Note. All referenced figures and drawings are found at the back of this manual.

Jan 1, 1980

By M. F. Trice

Pyrophyllite is a hydrous aluminum silicate (A1²Si4O10(OH)²)1 that, occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.' The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey12 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, ('are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. Sources At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This belt varies from 8 to 50 miles in width. Two major deposits of pyrophyllite lie along its eastern boundary, in what is known as the Deep

Jan 1, 1942

By A. A. Smith, J. S. Smart

THe elements silver, cadmium, tin, antimony and tellurium either are found as impurities in commercial coppers or are intentionally added to produce coppers for special uses. When present in small quantities, each of these metals exerts a significant effect on the properties of copper, but despite considerable experience and investigation much remains to be learned about their specific behavior. The presence of extraneous elements, particularly oxygen, complicates the study of individual additions of impurities in the range o to 0.05 per cent, and the use of high-purity copper has been found extremely helpful in circumventing these difficulties. It has also been found that individual behavior can be satisfactorilv determined from measurements of two commercially important properties, conductivity and softening temperature, according to methods that have been described previously.1,2 Data of this type, obtained in the course of a general investigation of the effects of impurities on the properties of both oxygen-bearing 2nd oxygen-free copper are presented herewith. All samples except those containing cadmium were prepared as 3/8-in. continuously cast oxygen-free rod from pure copper and weighed amounts of a similarly synthesized master alloy. Composition was checked by chemical methods, which in every case verified the calculated analyses. Test wires were cold-drawn one B, and S. number per pass on a string-up machine using four 30-min. 600°C. anneals at 0.3125, 0.257, 0.204 and 0.162 in. and a final cold reduction of 75 per cent to 0.081 in. Some oxygen-bearing samples were produced directly from the 3/8-in. oxygen-free rods by diffusion from a surface scale at 850°C. and drawn to size as listed above, but most of the alloys were remelted in pure graphite and cast through air into a I-in. round mold. The slugs were then hot-rolled to 5/16 in., drawn to 0.162 in., annealed as listed above, and drawn to 0.081 inch. Conductivity wires were annealed for I hr. at 100°C. intervals between 300' and 800°F., using a hydrogen atmosphere for oxygen-free samples and purified nitrogen for the oxygen-bearing type. All samples were quenched from the annealing temperature in 10 per cent H²S04 and conductivity was measured on a Hoopes bridge that had been checked against a Kelvin bridge. The softening temperatures represent the half-hard stage of the annealing curve as determined by a standard procedure.' Effect of Silver Numerous excellent studies of the argentiferous coppers are found in the literature, and these have been adequately

Jan 1, 1943

By Sean Harvey

One of the manifestations of the dynamically induced failures in deep coal mines is the violent ejection of coal from the ribs. A possible protection against such failures is the use of a specifically designed dynamic support system with reinforcement units having the sufficient capacity to absorb the kinetic energy of the dynamic failure and a skin support that can adequately contain the disintegrated coal. With this method of mitigation in mind, a recently introduced yielding rock bolt, trade name Roofex, has been identified (Harvey and Ozbay, 2009) as a possible energy absorbing component of a dynamic support system. According to the manufacturer?s specification, the Roofex bolts can yield 300 mm (or more) displacement while holding 80 kN pull load. In order to assess the performance of this support unit in coal ribs, a series of in situ pull tests performed in two coal mines in Colorado. The results show that, under conventional pull test loading conditions, Roofex yielding bolts perform very close to their claimed specifications, thus showing a potential for their use as the main energy absorbing component of a dynamic support system. Further studies are required to confirm the in situ performance of these bolts under dynamic loading conditions and also to develop a containment component for a dynamic support system for the mitigation of dynamic coal rib failures.

Jan 1, 2009

By M. Cuba

Geostatistical modelling aims at providing unbiased estimates of the grades of elements of economic interest in mining operations, and assessing the associated uncertainty in these resources and reserves. Conventional practice consists of using the data as error-free values and performing the typical steps of data analysis - domaining, semivariogram analysis, and estimation/simulation. However, in many mature deposits, information comes from different drilling campaigns that were sometimes completed decades ago, when little or no quality assurance and quality control (QA/AC) procedures were available. Although this legacy data may have significant sampling errors, it provides valuable information and should be combined with more recent data that has been subject to strict QA/QC procedures. In this paper we show that ignoring the errors associated with sample data considerably underestimates the uncertainty (and consequently the economic risk) associated with a mining project. We also provide a methodology to combine data with different sampling errors, thus preserving the relevant global and local statistics. The method consists of constructing consistent simulated sets of values at the sample locations, in order to reproduce the error of each drilling campaign and the spatial correlation of the grades. It is based on a Gibbs sampler, where at every sample location, the actual sample value (with error) is removed and a conditional distribution is calculated from simulated values at nearby sample locations. A value is drawn from that distribution and kept only if it satisfies some statistical requirements-specifically, the global relative error and local means and variances must be reproduced. All sample locations are visited and simulated sample values are generated iteratively, until the required statistics are satisfactorily attained over all sample locations. This generates one realization of possible sample values, respecting the fact that the actual samples are known to carry an error given by the global relative error. Multiple realizations of simulated sample values can be obtained by repeating the procedure. At the end of this procedure, at every sample location a set of simulated sample values is available that accounts for the imprecision of the information. Furthermore, within each realization, the simulated sample values are consistent with each other, reproducing the spatial continuity and local statistics. These simulated sets of sample values can then be used as input to conventional simulation on a full grid to assess the uncertainty in the final resources over large volumes. The methodology is presented and demonstrated using a synthetic data-set for clarity.

Jan 1, 2012

By Kenta Kusunose, Dadang Sundana, Ahmad Munib Fikry, Yosuke Unno

PT Smelting has operated the Mitsubishi Process in which feed materials are charged into the S- furnace through top lances using a pneumatic conveying system comprising 6 feeding tanks (S-Feeding Tanks). Each S-Feeding Tank was designed as a batch machine and had been operated in a batch mode so that feed materials are conveyed 70% of the operating time (conveying time). An S-Feeding Tank was revamped in August 2016 in order to attempt to achieve 100% conveying time during operation, aiming to reduce the furnace draft fluctuations and melt temperature fluctuations leading to reduced copper losses to slag and refractory wear on the sidewall in the melt zone. After two-year operation with some adjustments and modifications, it was concluded that the new system works as expected. During scheduled major shutdown in November 2018, the same modification was applied to all other 5 feeding tanks as the first one, while several modifications other than the S-Feeding system were also conducted for the purpose of expanding the capacity of the smelter. INTRODUCTION PT. Smelting (PTS) Gresik Copper Smelter and Refinery is located 30 kilometers north of the city of Surabaya, East Java major port. PT Smelting equity partners are Mitsubishi Materials with 60.5%, PT. Freeport Indonesia with 25%, Mitsubishi Corporation RtM Japan Ltd. with 9.5% and JX Nippon Mining and Metals corporation with 5.0%. PTS was established in February 1996 and started commercial operation of the Mitsubishi Process in 1999. The Mitsubishi Process is a unique technology which connects 3 stationary furnaces, namely the Smelting furnace (S-furnace), Slag-Cleaning furnace (CL-furnace) and Converting furnace (C-furnace) by covered launders. These features result in savings in manpower and energy, and make the process more environmentally friendly since there is no ladle transfer of melt. Figure 1 illustrates the outline of the Mitsubishi Process.

Jan 1, 2019

By Cocker J, Urosevic M

Seismic methods have become common for the detection of low-throw faults ahead of underground coal mining. Surface seismic methods cannot theoretically be used where dykes occur, because seismic waves transmit from the surface down to the seams, and reflect back to the surface. Consequently, where sub-vertical structure such as dykes occurs, the surface seismic method fails.The ability of seismic methods to image dykes depends on the geometry used, the dyke thickness and the seismic wave propagation mode in relation to dyke composition and internal structure. Surface seismic methods find it difficult to distinguish between faults/fractures and very thin dykes (1-2m in thickness) when the dyke's thickness is less than the seismic wavelength. Consequently, borehole seismic methods have to be used to detect the presence of such thin dykes.

Jan 1, 1998

By Frank Condon

?Location ?Background ?Drilling Program ?Mineral Resources ?Geology ?Economic Assessment ?Strategic Partner ?Located in Nunavik, Québec ?160 km northwest of Schefferville ?240 km south of Kuujjuaq ?160 km northeast of Brisay ?Magnetic Anomaly ?Property Boundary ?Diamond Drill Holes

May 1, 2011

By Hsiung SM, Jiang YM

The orientation and location of the hydraulic legs are two very important parameters for the design of shield supports in longwall mining. Studies have shown that leg orientations and locations of a support determine the magnitude, orientation and location of the resultant support resistance which in turn affects the efficiency of the support and the ability to prevent premature roof falls in the face area. Therefore, there is a need to determine the best combination of orientation and location of the hydraulic legs for each type of shield support under various geological conditions. This paper attempts to evaluate, first, the individual role of each parameter (orientation or location) and then to determine their integrating functions in terms of ground control employing finite element analysis. Three types of shield support (2-leg and 4-leg shields and 4-leg chock shield) with various combination of the parameters are simulated and their effects are discussed. The optimum design for each parameter for each support type under various geological conditions is also discussed and recommended.

Jan 1, 1988

By Rankin W. J

Increasing concern with the emission of sulphur dioxide from smelters and roasters has caused renewed interest in processes which can use waste sulphur dioxide, such as the sulphation of nickel laterite ores. The process described here proposes to by-pass the production of sulphuric acid and react laterite directly with a sulphur dioxide containing atmosphere. A thermodynamic analysis identified operating windows in which nickel sulphate forms while iron oxide (the major impurity in most laterite ores) remains stable. The initial assumptions included unit activity of all species except nickel oxide. The lowest possible nickel oxide activity (while maintaining selectivity) increased with increasing temperature, indicating that selective sulphation is favoured by low temperatures. The temperature of interest was found to be between 500 and 800¦C. Calculations show that a feed gas containing ten per cent SO2, five per cent 02, balance N2 requires a temperature greater than 650¦C for selective sulphation of nickel. Laboratory experiments showed that the assumption of unit activity of ferric sulphate was unrealistic above about 680¦C due most likely to the formation of solid solutions which decreased the ferric sulphate activity. Results are presented which illustrate the limiting equilibrium sulphur trioxide partial pressures at 700 and 730¦C below which selective sulphation occurs. Cobalt extraction was usually between 80 and 95 per cent under conditions yielding selective sulphation, whilst nickel extraction was about 50 to 75 per cent depending on temperature and choice of upper limit of iron extraction. An operating diagram is presented for a limonite ore and shows that the optimum reaction conditions are 680¦C and an input gas containing 20 per cent SO2. Under these conditions nickel, cobalt and iron extractions are 73, 95 and two per cent respectively.

Jan 1, 1996

By H. J. R. Way

THE work to be described was undertaken at various periods from 1937 to 1939 on the Busia gold field, in the eastern province of Uganda. It was decided to examine the possibility of reef prospection by the resistivity method, for it was not known how far the usually disintegrated nature of most reefs in the ubiquitous laterite near the surface would obscure indications obtained by resistivity traverses. The work at the commencement was therefore largely experimental, but the results obtained thereby were satisfactory, and a survey was started at the Government closed area at Amonikakine. With the limited time and resources at the writer's disposal, it was not possible to complete the survey to his satisfaction or to follow up exhaustively all the geophysical indications, but some of the results of the experimental work and the survey were of sufficient interest to be worth recording; in particular the relation between the width of reef, electrode separation and shape of the curve, and the interference effect of constant separation curves over zones of float are significant and useful. Three new veins were located, but only one contained sufficient gold to warrant detailed prospection. This was called the Geophysical reef, and was uncovered over a strike distance of 1140 ft., and there are indications that it extends over a distance of 1990 ft. These results and the recommendations consequent therefrom were embodied in a special report to the Uganda Geological Survey. HISTORY OF THE FIELD The Busia field is in the southeastern corner of Uganda near the Kenya-Uganda border, and is about 17 miles north of the northeastern corner of Lake Victoria. Gold was first discovered in the area in the stream beds by Davies1,2 in 1932. Subsequently numerous small alluvial claims were worked by prospectors and the area was prospected for reef by a company for periods varying from three to nine months, but was finally abandoned, as the results were considered unfavorable. Further prospecting by the Geological Survey in 1935-1936 under Davies3 and later under the writer4 uncovered three reefs with sufficient gold values to be of economic interest. These were finally taken over by a company known as Borderland Syndicate, which still owns the area, and from September 1937 to the end of 1941 about 13,000 oz. of gold was extracted from reefs of the area proved by the Geological Survey. Opencast mining operations are still proceeding (February 1943). The Amonikakine area lies to the immediate north of that of Borderland Syndicate. A certain amount of prospecting had been done when the writer started work there. As a result of his report, this area was taken over by another syndicate, but little further work was accomplished before it ceased operating because of difficulties of wartime working.

Jan 1, 1944

The mining of mineral sands in coastal aquifers is often constrained by other land use conflicts and inappropriate controls imposed through a lack of understanding of environmental interactions and processes. The recent experience with the Tea Gardens mining operation illustrates how increasing our knowledge and understanding leads to more effective management of environmental problems. As well as a source of heavy minerals, the Tea Gardens sand bed serves as a town water supply source. From past experience it was believed that mining could cause undesirable increases in dissolved iron concentrations in the aquifer, but the reasons and mechanisms for this phenomenon were not clear. A water monitoring program was therefore designed for the mining operation which was aimed at protecting the water supply borefield from any detremental effects. After one year the results of the monitoring program were assessed in the light of new knowledge and understanding of iron hydrochemistry. It was found that the existing program was not achieving some of its major aims, and was therefore modified to a more effective and cost efficient program.

Jan 1, 1988

The U.S. Bureau of Mines (USBM) has developed the coal Mine Roof Rating (CMRR) to aid in ground control. This paper describes the application of the CMRR at four coal mines operated by a major U.S. coal company. The mines are widely separated geographically, and cover a wide variety of geologic conditions and mining methods. The study found that the CMRR was a useful predictor of roof performance. In mines where the CMRR varied, and other parameters held constant, roof falls were associated with low CMRR values. Important similarities in roof performance were found in mines with similar CMRR values, despite radically different geologic environments. The analyses also indicated that statistics can be used to evaluate ground control performance. For these mines, a "roof fall probability" can be estimated from the CMRR and the intersection span. A spreadsheet program has been developed to facilitate treatment of CMRR data, and it is briefly describe

Jan 1, 1994