Search Documents

By M. J. Sapko

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations) even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of current and future pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners? Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic, and safe mine sealing technique that can enable mines seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble in combination with a conventional mine seal so that the pressure resulting from a gas explosion is reflected, absorbed, and attenuated, so the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a ?Passive Mine Blast Attenuator? (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals. DISCLAIMER: This information is distributed solely for the purpose of pre-dissemination peer review under applicable information quality guidelines. It has not been formally disseminated by the National Institute for Occupational Safety and Health (NIOSH). It does not represent and should not be construed to represent any agency determination or policy.

Jan 1, 2009

Cretaceous to Cenozoic sedimentary basins in Western Southland include a wide range of non-marine and marine sediments, in a structurally complex setting dominated by major fault systems. A reassessment of their mineral potential confirms large quantities of nonmetallic minerals (limestone, aggregate, marl), and smaller reserves of bituminous coal, lignite, clays, and oil shale. Hydrocarbon potential is largely untested. Metallic minerals are present in trace amounts, apart from platinum group minerals and some detrital gold. In the offshore area, seismic data suggest the hydrocarbon potential is significant. The Orepuki area has the most interest onshore.

Jan 1, 1992

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept. 22, 2007 at the Charles F. Barber Pavilion (Museum Convention Center) in Leadville, CO. The four inductees are James Harold Courtright (1908-1986), Dr. Howard L. Hartman (1924-2002), Charles Washington Merrill (1869-1956) and Kenyon E. Richard (1915-1993). The inductions will bring to 197 the number of mining “greats” whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2007

By Emöke Imre

A point-symmetrical linear coupled consolidation model with displacement boundary condition is suggested for the description of the consolidation around the pile tip after pile penetration. Analytical solution is given. Main features of the solutions are predicted by the analysis of the system of differential equations and, the boundary conditions.

Jan 1, 2002

By Arthur Darby

The city of Kuala Lumpur was founded in 1857 by miners seeking tin near the confluence of the Klang and Gombak rivers. The rapid development of the city and surrounding area since independence has led to more rapid runoff during rainstorms and to gradual canalisation of the rivers with some restricted sections. The outcome has been more frequent and more severe floods (Abdullah 2006). At the same time the centre of Kuala Lumpur has become a modern inter-national city with tall office buildings, hotels, and shopping centres connected by a network of wide roads and commuter rail systems. With these the cost of dislocation during floods has risen as has the cost of making good damage afterwards. The Government of Malaysia considered these consequences unacceptable and sought ideas from the private sector for a solution. Potential solutions consisted of variations on the themes of bypassing the city centre with a flood relief tunnel or of providing off channel storage or a combination of both. Since under Malaysian law a tunnel cannot be constructed under private property unless this is first purchased or agreement reached with the owner, it was necessary for most of the tunnel alignment to run below existing heavily congested roads. After considering these facts Gamuda Berhad and MMC Berhad, two leading Malaysian development and construction companies, decided to propose to Government an innovative solution in which the tunnel would be used to carry road traffic except during floods.

Jan 1, 2008

By Charlie Wyche

The British Solomon Islands Protectorate continued developmental work on bauxite deposits on the Islands of Rennell and Vaghena. A feasibility study was completed by Mitsui Mining & Smelting Co., Ltd., and Pacific Aluminum Ltd. (a subsidiary of Conzinc Riotinto of Australia Ltd,), and negotiations with the Government were in progress. The Government will receive a 25% share if the project is realized. It was estimated that the Islands contain 60 million tons of bauxite with an alumina content of 45% to 50%.

Jan 1, 1980

By C. Stapel, AA Groningen, R. J. De Meijer

"In recent years the Environmental Research Group of the KVI has been developing a number of radiometric techniques that may be employed in mineral sand exploration. These techniques involve: radiometric fingerprinting for assessing sand provenances and mineralogical composition; thermoluminescence for dating and provenance determination of sediments; a towed seabed detector to map seafloors for radiogenic heavy minerals and assessing heavy mineral volumes; and simplified transport mechanism models to explain and predict heavy mineral concentrations.All techniques exploit the property that heavy minerals as a group contain concentrations of naturally occurring uranium and thorium that are a hundred to a thousand times higher than in light minerals. In this paper the physics of a number of methods will be described together with a number of results. Based on these results potential applications to mineral exploration and mining are discussed."

Jan 1, 1994

By I. Stanculescu

The consolidation of thick and very compressible soil deposits by stone columns associated with cast-in-place plain concrete columns, has been performed for shallow foundations of some heavy industrial structures. The reduction of settlements and increase of soil bearing capacity were thus ensured as a result of soft soil interaction with stone and concrete columns. The results of model tests and in situ large scale applications are presented. A calculation procedure is also suggested for foundation bases improved by the proposed method.

Jan 1, 2010

By T. Phiri, Antoine Floribert Mulaba-Bafubiandi

Microwave energy has been recently used in minerals processing to speed up the leaching process or to improve the liberation of targeted minerals (Al-Harahshed and Kingman, (2003); Bradshaw et al., (2001)). Applied to the roasting of sulphide minerals, microwaves allow the ?tunning? of calcine types and products quality in addition to the energy savings as opposed to the conventional roasting (Mulaba, 2006). As more than 85% of world zinc is produced through the ?roast-leach-electrowin? route, an attempt was made to optimize cost, energy and product quality for metal extraction process route. The use of microwaves was the alternative process route selected for the optimisation. Pyrite concentrate (0.17% Zn, 0.09% Cu, 35.71% Fe, 43.76% S) and sphalerite concentrate containing 43.81% Zn, 0.37% Cu, 3.86% Fe and 44.39% S were microwave roasted in a multimode cavity of 2.45 GHz with varying power levels and for different durations. The produced calcines were characterized using AAS, XRF, XRD and Mossbauer spectroscopy while the determination of residual Sulphur was used as products quality control tool to ascertain the degree of roasting achieved on the feed. The leachability of the produced calcines in HCl, HNO3, H2SO4 and HNO3 + HCl has been studied in terms of the best leaching yield, process kinetics economics and environmental aspect. With 800 W power for 30 minutes, ZnO and Fe2O3 were formed corresponding to a 70% sulfur removed from sphalerite and 80% from pyrite concentrates respectively. While the roasting of the above concentrates appeared to be a first degree processes, it was noticed that the microwave assisted roasting of sphalerite and pyrite concentrates yielded lower sample surface temperature for a shorter time (i.e.less than 30 minutes) microwave exposition. Longer time (more than 30 minutes) microwave exposure showed a linear increase in temperature in function of power level used. While optimum roasting conditions were found at 800W, 30 minutes, a 10% increase of sulfur removal was noticed while pyrite concentrate was microwave roasted. Sulfuric acid was seen to give higher leaching yield than nitric acid. Zinc dissolution was hindered by the presence of franklinite.

Jan 1, 2007

By Y. P. Chugh, J. Ma

Higher production, better safety standard, and potential for automation are some of the benefits of longwall mining. Today, longwall face advances at a faster rate exposing many diversified rock layers in a short period of time. It is now a serious challenge to cope with ground control problems such as roof falls, face and floor failure, and excessive shield loading as fast as possible to minimize production and monetary losses. In Illinois coal mines, the existence of weak floor strata blow the coal seam may pose additional problems related to floor heaving, shield base punching, and associated roof and face falls. In this study, the effects of weak floor on longwall ground control are analyzed using two-dimensional finite element models. A two-leg 635.6-ton (700-short-ton) yielding capacity shield is included in the models to evaluate the effects of different thickness and material properties of the weak floor. The study indicates that the thickness and material properties of weak floor have significant effects on shield loading, the distribution and intensity of front abutment stress, failure zones in the surrounding strata, roof-to-floor convergence, and floor punching by the shield base.

Jan 1, 2000

By David R. Morrey

During the past 50 years, significant research has been performed in the ecology and physiology of plants that colonize soils containing elevated concentrations of heavy metals. Similar work has also been performed on plants that are able to survive acidic and saline environments. Efforts have focused on the ecological analysis of plant communities that occur over a range of metalliferous mining wastes. Investigations have been performed on the mechanisms that allow selected varieties of plant species to survive in normally phytotoxic environments and on the potential applications of metal-tolerant varieties of plant species. The purpose is the remediation and reclamation of mining wastes and soils that contain unusually high concentrations of so-called heavy metals. Characteristics of some mineral wastes Metalliferous mining wastes present special environmental restoration problems because of their toxicity. Potential toxicities are mostly caused by residual metals derived from weathering of low-grade ore or the waste products of mineral processing. In cases where pyrite forms a part of the mining waste, acid generation by oxidation may exacerbate the toxicity problem by promoting heavy-metal mobilization in aqueous solution.

Jan 1, 1995

THE object of the air-tight stopping is either to prevent a current of fresh air from getting into the fire area, or to prevent an escape of fumes and gases from the fire area into the workings of the mine. In the former case all is "plain sailing," but in the latter case there are certain difficulties to be overcome.In the Broken Hill Proprietary mine there were two styles of stopping used during the last fire-brick and bag and the following were the chief points that determined the use of one in preference to the other:-If the required stopping were to be more or less permanent, bricks were used, also if the area to be blocked were large-bricks being so much lighter and easier to handle than bags filled with -skimps. If, however, the air contained much gas, a bag stopping was put up. Great difficulty was experienced in getting essentially surface men, such as bricklayers, to work where there was the; slightest trace of gas; miners, however, would willingly do the work, and a bag stopping could be built without skilled labour.In old drives and gangways, where there was the liability of settlement, the bag stoppings were preferable to brick. The slightest movement around the sides or foundations of the latter would cause cracks, thus rendering the brick stopping useless;whereas, in the former, there was a certain amount of elasticity.

Jan 1, 1909

The Clyde Power Project, and its Clutha Valley Development forerunner, has taken widespread investigations for various hydroelectric purposes both along the valley floors upstream from Alexandra and on the higher schist terrain. As part of this work the nature and extent of many of the alluvial deposits have been resolved and the ages established with varying precision. Gold values have been approximately appraised in some areas as an element of environmental assessment.

Jan 1, 1992

By Young-Dong Cho, Yonghun Jong, Dong-See Shim, Seokwon Jeon, Chung-In Lee

The most important operation in the tunnel blasting procedure is to create an opening in the face in order to develop more free surface in the rock mass. This operation is highly dependent on the cut holes. In general, the burn-cut or V-cut is commonly adopted to blast the cut section. But, these traditional methods often raise problems. There are instances (a) that the actual advance is considerably less than the designed advance depending on the rock mass, (b) that they cannot sometimes enlarge the free surface efficiently and (c) that the blast vibration resulted from the cut blast exceeds the allowable vibration level. In order to resolve the problems, many different kinds of the cut blast can be considered.

Jan 1, 2005

By Dale S. Preece, Matthew A. Reisenmay, Avione Northcutt

The ability to simulate the explosive effects of land mines on military vehicles is a valuable capability in the defense community. The current competency levels of such simulations, however, are in need of improvement. Experiments have been conducted to measure the explosive induced impulse of a land mine on a steel plate placed above the explosive charge. The purpose of this paper is to report the findings of a variety of simulation tests conducted in order to correctly predict the empirical impulse data gathered in corresponding experiments. The computer hydrocode, AUTODYN v5.0.01 (Century Dynamics, 2003), is the simulation code used to simulate, and process the results. The experimental data has not been made available to allow computer analysts to exercise their codes on the problem without the temptation to tweak parameters in order to match computer code predictions with experimental results

Jan 1, 2005

By Jason Clarke, André R. Laplante

"The gravity-recoverable gold (GRG) ore characterization test was developed 15 years ago and has been applied to hundreds of ore samples. The test accurately determines the size distribution of GRG, at which grind it is recoverable, and the extent of its liberation above 150 µm. This contribution shows how the test can be simplified, what are the likely problems to occur, and what information is then lost. Two simplified versions of the test are presented, of which the simplest, grinding a 20-kg sample to a P80 of 75 µm, is retained as the best one. A database of 18 comparative tests is presented. The choice of the full GRG test vs. the simple test is discussed, as is the deportment of the GRG recovered in the standard test but not in the simplest test.INTRODUCTIONThe GRG test was developed in 1990 to characterize the progressive liberation of gold in representative samples of ores, with the primary objective of generating data for a gold gravity recovery model (Woodcock and Laplante, 1993; Laplante et al., 2000). Characterization includes the size distribution of GRG as well as the grind size at which it becomes recoverable. This is achieved in a 3-stage protocol of liberation and recovery using a laboratory centrifuge unit, a Laboratory Knelson Concentrator 3 inches in diameter (KC MD3). This protocol is shown in Figure 1. The first stage takes place at a F100 of 850 ?m (F80 of ~550 ?m), the second at F80 of 180 ?m, and the third at a P80 of 75 ?m. The rationale for the three cycles is the desire to preserve the original size distribution of the gold grains in the ore and to obtain a recovery grind size curve. The feed is a representative sample of ore that can be extracted from ore samples (e.g. drill core reject) or stream products of the grinding circuit other than circulating loads or product having undergone hydraulic classification (e.g. rod mill discharge or SAG screen undersize). Ideally the samples should weigh between 60 and 100 kg, depending on feed grade and gold top size. It is beyond the scope of this paper to fully discuss measures of representativity in the ore sample, for example Gy’s minimum sample mass model (Gy, 1979). However, further work in this regard may be an opportunity. The large initial weight facilitates representativity and minimizes weight and sulphide recovery to the concentrate (since concentrate weight is relatively constant at ~100 g), which limits the recovery of gold in nonsulphide gangue or gold carriers (i.e. sulphides). Thus, the 100 g concentrate carries principally discrete gold species, such as electrum, and native gold. The concentrate and a 600-g representative sample of gangue of each stage are screened down to 20 ?m and each size class is fire assayed (the concentrates to extinction, the tails up to 30 g per size class). The five coarsest size fractions of stage-1 concentrate are individually upgraded using a hydrosizer and the concentrates examined with an optical microscope to assess the degree of liberation of the gold phase. Scanning electron microscope work has established that the GRG has an excellent degree of liberation below 150 ?m in stage 1 and generally a good degree of liberation in stages 2 and 3 (Guerney et al., 2003); as a result the size distribution of the GRG has been found to approach closely that of gold grains (Nesset et al. 2005)."

Jan 1, 2006

By M. Doggett

All 231 Canadian primary gold mines that produced from 1946 to 2004 were analyzed with respect to their production and economic characteristics. Trend analysis revealed that the average annual capacity of Canadian gold mines, as measured by ore processed or gold produced, has increased over time. Conversely, the average grade of gold mines has decreased over time. The distribution of gold output is highly uneven: for example, the 22 giant mines producing more than 100 t (metric tonnes) of gold account for 62% of total output. Small mines producing less than 10 t Au account for 54% of total mines, but less than 4% of total gold. Each historical mine in the database was evaluated on the basis of a set of economic and technical assumptions to determine if it would be economic to develop today. Based on the net present value using an 8% discount rate, only 103 of the 231 mines were determined to be economic. About 80% of the uneconomic mines had less than 10 t of contained gold, and 63% had less than 5 t. It is concluded that these small mines would not be viable today due to a combination of real capital cost increases, and more stringent permitting and environmental regulations. The implication is that future gold supply in Canada will hinge on the discovery and development of a new generation of larger mines. Given that only one giant mine has been discovered in the past 20 years, it seems likely that gold output will decrease in the future.

Jan 1, 2007

By M. Newton

Optimization and sensitivity analysis of mineable economic volumes have been standard practise for open pits for many years now, and more recently software has become available to apply techniques for delineating mineable reserves for underground mines. In general these techniques have been applied to a single resource model to quantify mineable tonnes and grade for underground mining. However by using multiple conditionally simulated models both the risk associated with the mining parameters and the risk associated with variations in grade, tonnes and profit can be quantified. Using suitable software the mine planner can then easily and quickly define and compare alternative designs to assess and improve the robustness of and the confidence in the final design.

Jan 1, 2007

By G Njowa

Mineral resource evaluation and estimation process is not an exact science; however it depends on the knowledge and experience of the competent person and his ability to apply his mind, make reasonable assumptions, interpretations and exercise sound judgment in the mineral resource estimation process. The mineral resource evaluation results in a mineral resource statement are disclosed to investors. The minerals industry is presently undergoing rapid changes in legislation governing the public reporting of mineral assets. It has gone through different phases of development with respect to the reporting of mineral resources and mineral reserves (mineral assets). In the past no reporting was done and currently mineral assets are reported as a supplementary section that briefly describes the mineral asset termed ?the mineral reserve and mineral resource statement?. The current industry trend appears to be going towards recognition and disclosure of the mineral assets on to the balance sheet. This paper explores the salient issues behind the mineral resources and mineral reserve statement of vein and reef deposits published in the public domain. It also highlights the potential misleading consequences of these issues and which filter through to the valuation of these particular mineral assets. The creation of reporting standards in the minerals industry has made significant inroads in standardizing and consolidating the interpretation and understanding of the different classification categories in the industry in an effort to promote common interpretation towards these salient issues.

Jan 1, 2008

By Kristie Tarr

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

Oct 1, 2010