Search Documents

By Roger "Dean" Skaggs

Mechanical rock drilling is about 150 years old, and the fundamental principles of augering, penetration and dragging, pressure and rotation, and percussion have not appreciably changed. Surface mining blasthole drilling employs relatively shallow blastholes (to about 100 to 130 feet or 30 to 40 meters) with respect to the blasthole diameter and hole alignment while problematical is not a major universal problem. Modem underground mining methods are spacing development levels up to 400 feet (130 meters) apart, to take advantage of high powered mechanical drilling methods, requiring very long blastholes compared with surface mining. Blasthole alignment is a major problem in underground mining and this paper will address the aspects of percussion bit design which impact on hole alignment and drilling and blasting costs, i.e. bit geometry, cuttings removal, penetration-retraction.

Jan 1, 1997

By Thomas A. Simpson

Traveling through the moors and valleys of Cornwall, England, one is reminded of the extensive mining activities of the past. Abandoned shafts, remains of granite block wheel houses and engine houses, battered brick stacks, old calciners, overgrown water wheel pits, count house remains, overgrown waste pits, and old portals are gaunt monuments to a once flourishing mining industry. Cornwall is bordered on the north by Devon and occupies the south-western most tip of Great Britain. The Atlantic Ocean borders the promontory; to the north, the mouth of the famous Bristol Channel faces the open sea; and to the south, the English Channel separates the land masses of Great Britain and Europe. This part of England is probably the most extensively mined ground in all of Europe. Such great mines as Dolcoath and Wheel Vor, Consols and South Carodan, Levant and Bottalack, remain legendary in the annals of metal mining in the nineteenth century. Many US mining districts hold close ties with Cornwall, Devon, and Wales through ancestors who emigrated from there to work in US mines in the eighteenth and early nineteenth centuries. Their descendants can be found in many major US mining districts, and their terms, expressions, customs, and methods have left an impact on the US mining scene that remains with us today.

Jan 9, 1981

By Johnson N. W

After an unsuccessful transfer from the laboratory to the pilot plant of galena flotation technology which used sodium metabisulphite and ethyl xanthate, laboratory flotation tests were conducted to identify any unusual variables which had a deleterious effect on the position of the lead rougher grade recovery curve for Hilton and Mount Isa silver-lead-zinc ores. Two variables (pulp temperature and contact time for ethyl xanthate and sodium metabisulphite) had important deleterious effects.The findings allowed a successful transfer of the laboratory process to a pilot plant scale process. The effect of temperature was important because the higher temperature (40°C) in the pilot plant pulp increased significantly the rate of reaction between ethyl xanthate and sodium metabisulphite. In the laboratory process at 20 to 25°C, the reaction rate was lower and did not interfere significantly with the process. The contact time for the two reagents was also important in the pilot plant scale process because of the higher reaction rate at 40°C.To employ ethyl xanthate in the pilot plant process, special precautions were required. Further, a collector (Aerofloat 241) from the dithiophosphate family was used successfully in the pilot plant process.

Jan 1, 1988

By Thomas J. Peters

A mineral survey of the Sill Hill RARE II area (No. 5304), covering 5,200 acres (2,100 ha) of the Cleveland National Forest, San Diego County, California, was conducted by the U.S. Bureau of Mines and the U.S. Geological Survey. This survey was in conformance with the Resource Planning Act (RPA) of 1974, as amended by the National Forest Management Act of 1976, to provide mineral resource information for study area classification. Bureau of Mines personnel made an economic appraisal of mineral deposits by searching pertinent geological and mining publications as well as U.S. Bureau of Land Management, U.S. Forest Service, and U.S. Bureau of Mines files and records. Known mines, prospects, and mineralized localities were examined during 1981, and sampling and mapping were done where warranted. The Geological Survey 'did geologic mapping, geochemical sampling, and geophysical surveys to aid this study.

Jan 1, 1983

By D Craw, G Eis

Late Cretaceous Blue Spur Conglomerate preserved as isolated remnants at Gabriels Gully, Weatherstones, Forsyth, Waitahuna Gully and Adams Flat was deposited during the intiation and early stages of extensional movement on the Tuapeka Fault zone at each locality. The deposits represent successive courses of a single fluvial system flowing across the Tuapeka Fault zone from the up-thrown (northeast) block. Each course, beginning with the channel at Gabriels Gully, was abandoned as a result of uplift-induced defeated antecedence in favour of a new course farther to the southeast around the southeast-propagating tip of the Tuapeka Fault zone. Schist and quartz in the conglomerate was derived ultimately from schistose rocks northeast of the Tuapeka Fault zone. Caples Terrane greywacke detritus in the middle and upper beds of the conglomerate was probably recycled from pre-existing sedimentary cover on the up-thrown block, following initiation of uplift on the Tuapeka Fault zone at each locality. Most of the gold is derived from vein sources in Otago Schist rocks to the north, and/or associated placers. Hydrothermal veins at Waipori, Hindon, Barewood, and Macraes are the most likely primary sources. There is no evidence to support previous interpretations of deposition by river systems flowing from the southwest, or axially along the Tuapeka Fault zone from northwest to southeast. High gold grades within Blue Spur Conglomerate should have a linear trend more or less similar to the orientation of the host channels, but are likely to drop off rapidly to the southwest. Extensions of the conglomerate-filled channels are unlikely to be preserved, but there is a strong probability that younger placers recycled from the former channels exist.

Jan 1, 1999

Investigation of the Classification Operation in a Coal Pulverising Vertical Spindle Mill Coal pulverisation in power plants is a major electrical energy consumer. In 2006 more than 41 per cent of world electricity generation was from coal where pulverisers use 0.5 to 1 per cent of gross generation. Therefore, pulverisers are an important target for optimisation not only for reducing costs of power generation but also for reduction of greenhouse gas emissions. A better understanding of the operation of pulverisers is an essential requirement for their optimisation. However, little information is available, other than operating experience, on the performance of pulverisers and how these react to changes in operational variables. This study investigates the effect of changes in coal and airflow feed rates on the classification performance that occurs in an industrial scale ball-and-race vertical spindle mill in which the pulverisation and classification processes are linked together due to the separator classifier being an integral component within the pulveriser. In order to decouple the breakage and classification processes, samples were cut from upward flowing streams through sampling ports drilled on the pulveriser body at different locations. Specific sampling tools were developed. Samples collected from the pulveriser were size and density fractioned to distinguish the differences in behaviour of the components, namely coal and mineral matter. The coal flow rates on dry basis within the mill and around the separator classifier were calculated by mass balancing the multi-component data. The difference in classification behaviour of components during pneumatic transport was confirmed. The response of the circulating load in the mill (~600 to ~1100 per cent) as well as the dependency of fineness of the streams to the operating variables was demonstrated. The approach taken in this study has proved that development of a classification model for a vertical spindle mill pulverising non-homogeneous materials, eg coal, requires treating these materials as multi-component/composite substances.

Sep 13, 2010

By A. M. Hanna

This paper presents the experimental investigation on the ultimate skin friction of batter piles. The model piles were pushed in medium dense sand deposits at different inclinations up to 30 with respect to the vertical and tested under axial compression loads. The decrease in the total skin resistance with increasing pile inclination can be explained in terms of the reduction of the ave­rage mobilized angle of friction between the pile shaft and sand. The analysis, which takes into account asymmetrical earth pressure distributions around the pile shaft, showed good agreement with experimental results.

Jan 1, 2010

By Jewel A. G. Gomes

Green rust (GR) are layered Fe(II)-Fe(III) double hydroxides, having a pyroaurite-type structure consisting of positively charged hydroxide layers and hydrated ions in interlayers. This special feature of GR is very efficient for wastewater treatment as the pollutants are easily taken in or exchanged with the anions in the interlayers. It can be simply and cost-effectively produced by electrocoagulation (EC). Chicken processing plant (CPP) produces large amount of wastewater containing variety of readily biodegradable organic compounds, fats, and proteins. The possible re-use of properly treated CPP wastewater would be economic and environment friendly. In this study, we present our work on treatment of CPP wastewater using EC, specifically for the removal of COD. Analysis of the EC-treated water for reuse in the same plant is discussed considering the U.S.EPA regulations. Two types of EC-reactors were used for this purpose. To better understand the treatment mechanism, EC-floc was also characterized using XRD and SEM-EDS.

Jan 1, 2010

By L Neindorf

The development and application of paste fill, cement slurry aggregate fill and shotcrete bulkheads at Mount Isa Mines is described. The progressive changes in filling style in the Mount Isa copper mines from a dry fill based cemented rock fill to tailings based paste fill and slurry fills is explained. The development of shotcrete arched bulkheads and engineered drainage system is described. Details on how Mount Isa Mines has achieved approximately 30 per cent cost reduction in backfill operations through innovations are given. The development of a rocky paste fill is explained.

Jan 1, 2005

By Dale W. Richardson

Ductile hafnium was not obtained consistently by the conventional Kroll process. The bimetal reduction modification produced a more ductile hafnium by lowering the impurities, especially oxygen, in the sponge metal. Hafnium oxide was chlorinated in the presence of carbon to form anhydrous hafnium tetrachloride, which was reduced by sodium and magnesium in an inert atmosphere to produce sponge hafnium metal. After vacuum distillation to remove the byproducts, the sponge was arc-melted into ingot and rolled into strip. Metallic impurities were decreased by evaporating the hafnium tetrachloride from a fused salt. An excessive amount (over 1,200 parts per million (p.p.m.)) of aluminum was contained in some of the hafnium oxide, much of which remained as aluminum chloride in the hafnium tetrachloride during chlorination. Evaporation of the hafnium tetrachloride from a fused NaCI-KCI mixture during the Mg-Na reduction greatly lowered its aluminum content, as most of the aluminum and some of the other metallic impurities were retained by the fused salt.

Jan 1, 1961

Case 1: A driller raised a drill rig mast into a 7200-volt overhead power line. Both he and his helper were killed. Case 2: A driller-helper was pulling a winch cable toward a stack of drill steel when the cable contacted a 12,000-volt power line. The helper was killed, and the driller at the rig controls was severely injured. [ ]

Jan 1, 2006

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

By David R. Beadman

The Fleming method is widely used for the analysis and prediction of single pile behaviour under maintained loading. The method does not distinguish between bored and driven piles. Driven piling avoids the need to dispose of spoil from the pile installation and is therefore becoming increasingly attractive. This paper considers the theoretical effects of the possible preload at the base of a driven pile after installation, using the hyperbolic functions as defined by Fleming. The Fleming method is reviewed and the equations and analyses are adapted, using spreadsheets, to allow for a possible preload. The simplifying assumption of the effect of the elastic compression of the pile is also reviewed and a more analytical method adopted to assess the elastic compression. Some driven pile test data is analysed to consider the possible effects of the preload on the performance of a driven pile and to test the theoretical relationships that are developed in the paper.

Jan 1, 2006

By M. Kalin

"Ecological Engineering and Biological Polishing technology is a decommissioning approach for inactive coal, uranium and base metal operations. To improve acid mine drainage water some fundamental aspects of wetland ecology and sediment microbiology are combined, to provide conditions to allow for biomineralization of the contaminants.This paper summarizes the first records of microbial alkalinity generation in acid mine drainage through the utilisation of the ARUM process. The process requires that the seepage is at pH 4.5 where sulphate reducers utilize sulphate to produce hydrogen sulphide, which in turn precipitates with metals. The pH increase is brought about by alkalinity generating microbes.The ARUM process has been successful in increasing the pH from 2.5 to 7.0. Flow through reactors operated in the laboratory continuously for more than 60 days have removed Ni from 13 mg/L to < 0.01 mg/L. Design parameters are being developed for low flow rates of 5 L/min in a test system receiving seepage from a tailings.1.0 INTRODUCTIONAcid mine drainage associated with mining wastes poses a significant environmental problem. Conventional means to treat acid mine drainage (AMD) use chemical treatment system. Ecological Engineering technology uses natural biological means to curtail and ameliorate AMD during mine operations and at the time of decommissioning. The premise underlying Ecological Engineering technology is that AMD is the result of a natural process enhanced by mining activities. Therefore, in nature, a process providing a natural balance to AMD has to exist, which, when assisted through appropriate means, can counteract the detrimental effects of AMD on the environment. This process is microbial alkalinity generation which is known to occur in wetlands, lake and ocean sediments (Baas Becling et al, 1960)."

Jan 1, 1991

By Ali Mortazavi

In underground mining applications, successful blasting results in less damage, which may lower support costs, lower dilution and produce a uniform fragmentation. The explosive detonation process creates a pressure front that propagates a stress wave into the surrounding rock mass at a high velocity. The stress wave can induce varying degrees of damage, depending on rock strength and physical properties, to the excavated area. This paper presents a summary of a research project that was conducted to investigate the propagation of explosive-induced stress waves in hard rock media and the mechanism of rock damage and fracturing due to shock wave propagation. The primary objective of this work was to numerically simulate the experimental study of blast-induced rock fracturing conducted within Inco Limited, Mines Research department. ITASCA?s discontinuum code UDEC (Universal Distinct Element Code), was used to simulate the results of the controlled blasting experiments. In brief, the focal point of the paper can be summarized as follows: ? Investigate the size of the stress-wave-induced fractured zone around the blasthole, ? Examine the extent and direction of the radial fractures that form outside the blasthole, and ? Explore the mechanisms that cause rock breakage.

May 1, 2002

By Minggao Qian, Jialin Xu, Wenqi Lai, Weibin Zhu

This article advances an innovative concept explaining the connotation and technical system of "green" mining. The important theoretical foundations of "green" mining are the distribution and development characteristics of joints, fractures and bed separations, and the seepage and flow behavior of methane and water in the broken rock strata following coal mining. The main focus of "green" mining technique includes water-preservation in mining areas, coal mining under buildings with bed separation spaces grouted to retard surface subsidence, partial extraction and backfill mining, simultaneous extraction of coal and coal-bed methane, coal roadway supporting and underground disposal of rock waste, underground coal gasification, etc.

Jan 1, 2005

Discussion of the paper of Robert Henry Lee, presented at the New York Meeting, October, 1913, and printed in Bulletin No. 82, October, 1913, pp. 2515 to 2522. J. E. JOHNSON, JR., New York, N. Y.:-This subject is of great and increasing importance, as the exhaustion of the deposits of ore of ideal character compels the iron industry to turn more and more to those which are less desirable on account of physical structure as well as analysis. Thus there has come about the use of the Mesabi ores in this country and also of the Minette ores in Europe, which produce far greater percentages of flue dust than did the lumpy ores first used. It is a matter of common knowledge that the utilization of this flue dust, containing commonly 50 per. cent. or more of metallic iron, has been a problem very difficult and tedious of solution. The number and variety of the solutions now offered is a sufficient proof of this. . I have no intention of going into the merits or demerits of any of these processes as such, but there are certain considerations concerning the effect of their product on the operation and fuel economy of the blast furnace which I believe to be new and which I desire to bring out. There are two methods, so different as almost to be direct opposites of each other, whereby an ore may exercise an unfavorable effect on the economy of the blast furnace. The first of these is well known and results from the ore being refractory and highly resistant to the action of the reducing gases of the blast furnace. This results in its being incompletely reduced when it reaches the zone of fusion and in the reduction being finished by the direct action of carbon in the lower portion of the furnace. This is so well understood as to need little elaboration or comment. There is, however, another action which may be equally as fatal to the economy of the furnace as the foregoing, and as this point is, to the best of my knowledge, not generally appreciated, it is one upon which I desire to lay particular stress. This consists in the ore being, in a sense, too reducible.

Jan 12, 1913

By Jack Eloranta

This paper documents the relationship between material handling and processing coete compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this c!ase study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong. inverse correlation with powder factor (lbe powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

By P. C. Thakur

Frictional ignitions (also called face ignitions) is defined as the rapid oxidation of a mixture of methane and air with a visible flame that could last from a few seconds to several minutes. These ignitions have a potential to turn into a mine explosion and eventually a large-scale mine fire. Over the last 22 years, U.S. coalmines have had 1566 frictional ignitions. There were no fatalities but serious injuries have occurred. Every effort, therefore, should be made to prevent frictional ignitions. The preventative measures fall under four categories: (a) degasification of coal seams prior to mining, (b) adequate ventilation, (c) wet cutting or water-jet assisted cutting and (d) machine design to minimize ignitions. The paper discusses each of these techniques in detail.

Jan 1, 2006

By J. Wennerstrand

Slender steel piles have found an increased use in Sweden in resent years. These piles are often driven throw soft normally consolidated clay to refusal in till or at the rock surface. In contrast to most other piles the bearing capacity with regard to failure of the shaft is in many cases smaller than the bearing capacity with regard to failure of the soil or rock at the lower end of the pile. Imperfections such as deviations from a straight line of the pile centerline and residual stresses in rolled and welded profiles are important for the capacity of the pile shaft. Even thow the second order moment caused by initial deviations in piles is only half of that in a column with the same slenderness, imperfections can and should be accounted for in much the same way as for columns.

Jan 1, 1989