Search Documents

By J. Bertisen, G. Davis

Previous analyses of small samples of mining projects have found that feasibility studies tend to well under-estimate the actual capital costs of the project. Our review of 63 mining and smelting projects completed over 4 decades confirms that as-built capital costs are, on average, 25% higher than as estimated at the bankable feasibility study stage. There appears to be little attenuation over time of this bias in capital cost estimation, at first appearing to reflect an absence of learning on the part of the consulting engineer. We instead argue that this persistence of bias is intentional, driven by a scarcity of project financing and the need to inflate the project economics in a bid to secure financing. Around this intentional bias is a considerable amount of scatter. Roughly half of all projects’ as-built capita costs fall outside of the expected ±15% of the feasibility study capital cost estimate, even after allowing for intentional estimation bias. Cost overruns of 100% or more happen in roughly 1 out of 13 projects. The data reveal that a shifted lognormal probability distribution should be used when modeling mining project capital costs in a Monte Carlo analysis.

Jan 1, 2007

In 2005, a total of 739 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). These mines (e.g., potash, gypsum, salt) comprised 5.0% of all operations. ? Mines producing common clay comprised 26.9% (n=199) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the Virgin Islands.

Jan 1, 2008

To improve the ventilation of large-opening under-ground stone mines by using stoppings made from stone left in place. Background Underground stone mines typically use large room-and-pillar openings with little ventilation control. Stone miners may be exposed to contaminants that include silica dust, diesel particulate matter (DPM), exhaust gases, nuisance dust, and face shot (blasting) fume gases. The health risks from breathing these fine particles and toxic organic materials are well documented. Although contaminants such as dust or diesel exhaust can be some-what controlled at the source, the escaping contaminants are often diluted and removed from work areas using ventilation with minimal controls. In many cases, current mine ventilation practices use trial-and-error techniques to improve ventilation. The growing realization of the importance of a healthy work environment along with increased regulations will require many stone mines to implement new ways to improve ventilation. In-place stone stoppings are one option. Mine air flows from one point to another because of a pressure differential between those points. This pressure differential is established using a mechanical fan in conjunction with separations (stoppings) between high-pressure (intake) and low-pressure (return) airways. The separation of intakes and returns is an important concept that is used in most other types of mines. Normally, air moves through underground stone mines with minimal control technology. Fans are placed in locations where they are thought to be most beneficial, and intakes are not separated from returns. In a few smaller underground stone mines, proper ventilation can be achieved with a few strategically placed fans. However, as these mines increase in size, moving adequate quantities of air through-out the mine becomes harder, and separation of intakes and returns becomes a problem. Building traditional mine stoppings to separate the intake and return airways in entries with a cross-section area often exceeding 800 ft2 is difficult. The stoppings must be able to withstand both the dynamic pressure from face shots and the static pressures created by the fans. Construction and maintenance difficulties, as well as high costs, are the main factors preventing these traditional mine stoppings from gaining wide acceptance by the stone mining industry.

Dec 1, 2002

By Douglas A. Anderson

Mine the Internet? You bet. Precious information resources are there to be found by those willing to explore. Of course, the stratigraphy and the exploration tools must be learned. This article is is designed to help learn those tools and how to find the information that can help the reader. However, beware the Internet. It can be addicting. On the other hand, information can be found that you never suspected. And users can make contact with people who might otherwise never have crossed their paths.

Jan 1, 1996

Jan 1, 1967

By R. Bitmead, R Barker, A. Drake

The opencut coal mine is located about 50 km west of Brisbane, the capital city of Queensland in Australia and produces about 140 000 tonnes per annum of high grade steaming coal utilising a small team (ten) of personnel to mine remnants of the Aberdare and Bluff seams left by previous underground mining. This, in itself, is not remarkable except that one of the seams has commenced spontaneously cornbusting resulting in temperatures in excess of 55’C commonly being encountered with portions of the p’it being wreathed in steam. To extend mine life, the mine required a blasting system that would: . Safely blast in temperatures below 100°C . Significantly reduce overall unit costs . Not increase the current vibration impacts on nearby housing . Not increase flyrock.

Jan 1, 2002

By Eric E. Cather

Approximately 270,000 cu yd (20[0],000 cu m) of inferred subeconomic auriferous gravel resources were estimated in three Tertiary deposits in the Polk Springs study area (fig. 1 and table 1). These resources are exposed between tuff-breccia and lava flows of the Pliocene Tuscan Formation and Paleozoic or Mesozoic metamorphic rocks which suggests that although no deposits were identified in the other RARE II areas, they may be concealed beneath the Tuscan Formation. Difficulty in choosing drilling targets will make the likelihood of resource discoveries small. The development and production of these deposits would also be prohibitive under current economic conditions due to the thick covering of volcanic rocks. Recent stream gravels of Deer Creek in the Polk Springs study area contain enough gold to attract gold hobbyists; however, the stream gravels do not have sufficient volume to be considered a resource. Potential exists for additional auriferous gravels near the Occidental Mine in the Polk Springs RARE II area.

Jan 1, 1983

By Terry J. Close

A mineral resource survey of the 940-square-mile (2,434 km2) Hells Canyon study area, which includes Hells Canyon Wilderness, Snake and Rapid Wild and Scenic River's, and adjoining roadless lands in Oregon and Idaho, indicates the area is highly mineralized. Thirty-four lode deposits within the study area have resources totaling about 31 million tons (28 million t) containing copper, silver, zinc, gold, and lead; another 42 lodes, not sufficiently exposed to allow resource estimates, are believed to have mineral potential. The most important deposits are copper-, silver-, zinc-, gold-, and lead-bearing volcanogenic occurrences, followed by silver-and copper-bearing contact replacement (tactite) deposits; other lode occurrences are relatively unimportant. The most important placer deposits occur at Dry Diggins; placers along the Snake River are small and scattered. The study area has extensive deposits of limestone and sand and gravel; it has little potential for energy resources.

Jan 1, 1982

By Nutter R. S.

A methodology has been developed for qualitative safety hazard evaluation and quantitative reliability analysis of mine monitoring and control systems. Detailed application of these techniques were made to two commercial monitor/control systems and to a West Virginia University distributed microprocessor-based system. A controlled environmental test was conducted on a set of one of the commercial system's outstations. A software reliability evaluation methodology was also developed and applied.

Jan 1, 1982

By Harvey Patashnick

Current state-of-the-art microweighing technology represented by the Tapered Element Oscillating Microbalance (TEOM) is utilized as the basis for a new generation of Personal Dust Exposure Monitors (PDEM's). Two design configurations are presented. The first is an end-of-shift analysis system which uses small TEOM-PDEM cannisters that replace the filter cartridges in the current PDEM system. All other components carried by the miner (cyclone preseparator and pump) are the same. After the shift the TEOM cannister is plugged into an interface box which enables a minicomputer to automatically identify the unit, determine the dust mass increase during the shift, compute the shift average dust mass concentration, and print out and/or store the data. The second design is a real-time TEOM-PDEM system which is capable of operation over a 10-hour shift and on demand display real-time dust concentration level, time weighted average, and shift average concentration. As a result of the design study, a prototype end-of-shift analysis system was fabricated and delivered to the Bureau of Mines. A description of this system which consists of six TEOM cannisters, interface electronics and minicomputer is given. The system represents a significant advance in the dust monitoring program in terms or accuracy and automation.

Jan 1, 1983

By Steven W. Schmauch

The Farlin Creek study area encompasses 610 acres managed by the Bureau of Land Management in Beaverhead County, Montana. A mineral survey was conducted by the U.S. Bureau of Mines and U.S. Geological Survey in 1984. Bureau of Mines personnel reviewed literature and county mining records, and examined prospects or mineralized areas to determine its mineral potential. Geological Survey personnel evaluated the area by geochemical sampling and geophysical surveys. The study area is included in the Mount Baldy mining district. Nearby mineralized Quartz veins or tactite bodies apparently do not extend into or exist within the study area. No significant gold or economic detrital minerals were found in samples from streams draining the area. All of the study area is leased for oil and gas.

Jan 1, 1985

By Po-Ming Lin

Stress has a significant effect on the stability of pillars. In order to get an accurate picture of pillar stability, one needs information not only on the primary Stress distribution but also on all the Subsequent Stress changes as time passes. Sonic methods are some of the fastest, most economical and least destructive means of stress prediction. The wave propagation velocity has long been applied to the investigation of the upper mantle and crust stress. Recently, it has also been applied to the prediction of rock bursts and to mine site investigations. Another parameter for investigating stresses in rocks is the attenuation coefficient. Attenuation has been observed to be more sensitive to stress changes than wave velocity; however, the measurement of attenuation is more difficult than that of wave velocity. In this paper, the mechanism of sonic attenuation in rock is reviewed. Both the velocity and the attenuation of sound waves in five different rock types under various stress fields were examined in the laboratory. It was found that for a specific rock type the relationship between the velocity ratio and stress, as well as that between the attenuation coefficient ratio and stress, can be expressed by simplified second order polynomial equations.Research showed the attenuation coefficient to be more sensitive to stress change than the velocity ratio. A field investigation method was proposed using a Schmidt hammer as a repeatable energy source. Initial trials appeared to show that monitoring by the wave attenuation method gave more repeatable data than monitoring wave velocity.

Jan 1, 1984

This appendix is composed of five sections, each of which is tabbed for ease of access. The sections are as follows: ? Fire incident report forms for underground mine fires. There is one form for each incident listed in Table II-1a. They are ordered chronologically with incident numbers corresponding to those in Table II-la. ? Fire incident report forms for surface mine fires. There is one form for each incident listed in Table II-lb. They are ordered chronologically with incident numbers corresponding to those in Table II-lb. ? Journal article report forms. There is one form for each article reviewed. They provide supplemental information to that contained in the fire incident report forms for selected fires. Index 11-14 keys the journal article report forms to the appropriate fire incident report forms. ? Non-reportable incident descriptions for underground mine fires. This is a listing of underground fires for which MSHA regulations do not require formal reports. ? Non-reportable incident descriptions for surface mines. This is a listing of surface fires for which MSHA regulations do not require formal reports. This appendix is intended to be used in conjunction with the tables and indexes contained in Volume II of this report and, as such, should be considered an integral part of Volume II. The indexes in the body of Volume II provide a means of ready reference to the underground and surface mine incident report forms. For those readers with interests other than those indexed, Tables II-la and II-1b can be used to locate specific incidents of interest. Complete incident information can then be obtained from the corresponding report forms in the first two sections of this appendix.

Jan 1, 1980

Coal has become an enormously important export industry. Owing to a range of mainly natural advantages, Australia has been able to almost treble its exports in a little over the last decade. Australia is now the world's second largest exporter and coal is now the nation's largest single export earner.Despite this very significant growth, Australia's competitive position is in jeopardy.

Jan 1, 1984

By M. Ahrens

Gearless mill drives (GMD) are a well established solution for grinding applications in the minerals and mining industries. The paper describes the functionality and technical features of such drive systems as well as the development and the progress of GMD systems over the years. With an increasing installed base and many drives operating for many years, there is an increasing need to modernize or revamp existing GMD installations. The first installations of GMD took place in the cement industry and have demonstrated that ringmotors can achieve a lifetime well above 40 years, if maintained properly. The life cycle time of many other components, especially electronic parts, is usually shorter. It is therefore necessary to replace aged or out-dated components early enough in a planned manner in order to reduce the risk of component failures and the related shutdown times. Modernization upgrades can range from minor software updates to a revamp of the cycloconverter. The paper describes typical examples of such upgrades and shows the most important aspects that need to be considered.

Jan 1, 2008

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation. MFIRE was written in Fortran 77 and compiled with Microway1 Fortran for the Intel 80386 based computers with a 80387 math co-processor. The source code is portable and available for users who wish to modify the source code to operate on other computers. This user manual describes the development of MFIRE, the input format and requirements, the output, common errors, fire parameters, and examples MFIRE application. Valuable reference material is included in the appendices. Knowledgeable users may skip directly to the PROGRAM INSTALLATION AND OPERATION section to begin using MFIRE immediately.

Jan 1, 1995

By P. Cole Gregory, Michael R. Yenchek, John C. Edwards

The U.S. Bureau of Mines investigated the performance of portable power cables under transient conditions. This research had a twofold purpose: (1) to define the thermal characteristics of electrically overloaded trailing cables, and (2) to conceptualize electrical protection for cables that allows maximum cable efficiency without diminishing electrical safety in underground mines. Several tasks were under- taken in support of these goals during the 3-year research effort. Overload tests ranging from 2 to 12 times rated ampacity were conducted in the Bureau's Mine Electrical Laboratory. Two thermal models of energized type G-GC trailing cables were constructed, one based on thermodynamic theory and the other using empirical data from previous Bureau load tests. The empirical model was then incorporated into an interactive computer program that can assist designers and approvers of mining machines in selecting the appropriate size trailing cable. This program can be the basis for a cable protection system that ensures that cables are not the source of fires, ignitions, burns, or explosions underground.

Jan 1, 1993

By Alex Chapman, Cam Thomas, Bryan Karney

"During the early summer of 1989, Ontario Hydro removed a concrete portion of the North Channel Dam at Crystal Falls Generating Station by blasting and excavating in marine conditions. Because of the severity of underwater blasting and because the site was in close proximity to the replacement dam, there was concern that hydraulic shock waves generated by the detonation could damage either the new dam or its control structures. This paper examines the data associated with the hydraulic shock waves generated by underwater blasting, and studies the effectiveness of an air curtain in reducing the peak pressures. In previous trials using the air curtain technique, a rule-of-thumb factor was used to estimate that only 10% of the original pressure pulse would propagate across the air curtain. However, this value had little basis in theory. A theoretical formulation of the problem by Karney in 1989 indicated a provisional value of 0.18 for this factor, but was heavily dependent on confirmation from in-field testing. Data provided by Ontario Hydro from an actual blasting procedure indicate that a more conservative value of 0.32 may be more appropriate. Thus.although the air curtain did provide considerable reduction of peak pressures, the data at Crystal Falls indicates its performance was below the anticipated level. However, due to problems with the instrumentation and some inconsistencies in the resulting data. it is recommended that this value be further refined as additional data become available."

Jan 1, 1992

By P. W. Godbehere

"INTRODUCTIONMagnetic mill linings have been developed from an invention by Mr. Bertil Brandt, the originator of the Skega rubber lining. The OREBED magnetic mill lining is a concept in which rubber covered strontium ferrite permanent magnets are arranged on the inside wall of a mill shell so that they attract magnetically susceptible material be it ore, media or tramp, to form a protective layer over the magnets and to serve as an operating surface with indefinite life.Noranda Mines Ltd. through its associate Norcast Division of Noranda Metal Industries formed a joint venture with the inventors to market magnetic mill linings in North America. For the past twelve months trials have been undertaken in conjunction with Orebed Inc. to test and develop these linings for grinding mill applications at the Horne Concentrator. Two independent milling circuits are currently being operated, one treating a siliceous gold ore and the other a copper slag.This paper presents the results of the magnetic lining test programme to date."

Jan 1, 1983

By Dean Workman

Located in downtown New York City, this project necessitated an innovative conveyor design for successful muck removal. This paper will discuss the technical challenges and engineering solutions of the muck transport system which consists of every commonly recognized version of a belt conveyor. The elaborate system includes a TBM conveyor integral to the back-up system, a wall-mounted extensible conveyor, a crown-mounted transfer conveyor, a floor-mounted fixed-length conveyor, a pocket-belt vertical conveyor, three cascading overland conveyors, and one radial stacker. The most challenging design element was an over-land conveyor featuring a box truss for muck transportation over Northern Boulevard while simultaneously going under the Queens Plaza railroad viaduct. An overview of the project is provided along with the following topics: developing final plans from the proposal concept, interfacing with existing works, communication with the joint venture, and complying with local regulations.

Jan 1, 2008