Search Documents

By Gregory J. Canivan

Three test pile programs were conducted in Charleston, South Carolina to evaluate differences in bearing resistance due to installation methods. The tested piles were installed with impact hammers and vibratory drivers through soft clays and/or loose sands into the Cooper Marl, a stiff calcareous marine clay or silt. Piles driven into the Cooper Marl experience significant capacity gain with time following initial installation due largely to pore pressure dissipation. Pile size and pile type were both known to affect pore pressure generation during installation and subsequently the capacity gain with time. The test programs were primarily conducted to optimize pile design values and construction methods with regard to trestle construction but the results also contribute to the understanding of driven pile behavior. High strain dynamic testing was performed on several open-end pipe and H-piles. The measured difference in long-term bearing capacity of the H-piles as a result of the two installation methods was negligible, while the short-term bearing capacity of the pipe pile was larger when the piles were installed using impact hammers. The lower short-term resistance in the vibratory driven piles is attributed to larger excess pore pressures generated during installation compared to those generated during impact driving.

Jan 1, 2002

By Shahriar Vandani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles (2.6 km) of highway, including seven new bridges, three new cut-and-cover tunnels, and a new undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles (9 km) from the San Andreas Fault, capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. The Main Post Tunnels (MPT) are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) long. The MPT site underlain by loose sandy soils susceptible to liquefaction and lateral spreading. Excessive racking and permanent displacement due to lateral spreading are identified as the main seismic vulnerabilities. Analyses showed that without ground improvement, tunnel racking of over 5 inches (13 cm) and permanent lateral tunnel displacement of up to 15 feet (4.6 m) could be anticipated. Cement Deep Soil Mixing (CDSM) is proposed to mitigate slope displacements and increase lateral stiffness of the foundation materials to reduce tunnel racking. A series of 2-D fully dynamic time domain analyses were performed to evaluate the performance of CDSM, confirm that performance criteria are met, and optimize the CDSM geometry and replacement ratio. The use of CDSM reduced the permanent tunnel displacement from over 15 feet (4.6 m) to less than 1 inch (2.5 cm). Tunnel racking was also reduced significantly. The adopted analytical approach presented herein can be considered for future tunnel design projects in seismically active areas.Introduction The Main Post Tunnels (MPT) are an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. The MPT are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) in length. As shown on Figure 1, the project site is located in a seismically active area, about 5.6 miles (9 km) east of the San Andreas Fault and 12.5 miles (20 km) west of the Hayward Fault. The San Andreas Fault can generate magnitude 8 earthquakes while the Hayward Fault is capable of producing magnitude 7.3 earthquakes. The design Peak Bedrock Acceleration (PBA) is 0.46g for the upper level design earthquake. The project alignment is shown on Figure 2."

Jan 1, 2014

By Lukasz Maciag, Ryszard Andrzej Kotlinski, Ryszard Krzysztof Borówka, Dominik Zawadzki

Concentration and composition of rare earth elements (REE) and major elements in the sediment samples from the IOM H11 Fe-Mn nodule deposit, eastern part of the Clarion-Clipperton nodule field (located between the Clarion-Clipperton Fracture Zone - CCFZ; tropical Pacific), have been studied. We show the controls on REE concentrations and described vertical/horizontal variability of selected metals in pelagic sediments from the CCFZ. According to Kato et al. (2011), who analyzed 2000 seafloor sediment samples at 78 sites of the Pacific Ocean, deep-sea mud shows high concentrations (2230 ppm maximum) of ?REY and could be potential resource of these elements in the future. However, our work does not fully confirm that sediments in the IOM H11 are significantly enriched in REE.

Sep 1, 2014

By John F. MacDonald

From 19BS thru the present, Guy F. Atkinson Construction Company has been involved in several transportation construction projects in the Seattle area. Two of these contracts, the Mt. Baker Ridge Tunnel, and The Seattle Bus Tunnel, had unique foundation features. MT. BAKER RIDGE TUNNEL ACCESS PITS The Mt. Baker Ridge Tunnel is part of the general upgrading of the I-90 freeway between I-405 and I-5 (see Fig. 1). It is located on the western shore of Lake Washington and consists of a 1300 foot long large diameter tunnel thru Mt. Baker Ridge. The ridge consists of over consolidated silts and clays overlain by a loose to medium dense silty fine sand. The water table is perched in this upper layer of material. The clays of Seattle have a history of being very sensitive to excavation. The hills are marginally stable and numerous landslides have occurred recently in the area of the tunnel. [ ]

Jan 1, 1990

By Robert Stefanko

In the context of the following report, an hazardous location can be described as any industrial area in which flammable or explosive gases, vapors, and dusts can be encountered. When electrical apparatus is used in such hazardous atmospheres, the chance of a dust or gas ignition is ever present. Consequently, in an effort to reduce the ignition hazard, several protection systems have been devised. Such systems are termed electrical hazard reduction techniques. The most widely accepted and used of these, the explosion-proof enclosure, is the principal subject of this report. However, other techniques are briefly mentioned. Hazard reduction techniques used in coal mine atmospheres (which can contain methane, coal dust, and air mixtures) are classified as Group I. The explosion-proof enclosure commonly used in mines is defined by the USBM Schedule 2G as a device that can contain internal explosions of methane-air mixtures without undergoing damage or excessive distortion and without an ignition of a surrounding methane-air mixture or discharge of flame. (100) Internationally, the definition remains the same except the words "discharge of flame" are not present. (4,5,31,42,52,76,102) The latter description often refers to flame-proof enclosure construction, but the terms "flameproof: and "explosion-proof" commonly have the same connotation. These enclosures which may not be vapor tight, are distinguished by heavy-wall cast or welded construction and bolted or threaded close fitting flanges.

Jan 1, 1974

By Thomas A. Giordano

Portable communications equipment is becoming increasingly important in underground mining. Proper selection of microphones and hearing devices to be part of these communication systems is essential if the messages are to be transmitted intelligibly. In this program a thorough study of the requirements for these transducers was made with respect to intelligibility, mechanical configuration, human factors and safety. A computer analysis was made to predict how several combinations of transducers would perform at typical mining noise levels. A survey has been made of those microphones and hearing devices on the market today that might be applicable to the miner communication system. Several systems are proposed and evaluated.

Jan 1, 1976

By Peter Reinders, Dirk Hummel

This paper describes a newly developed Surface Remote Blasting System (SURBS) for electronic detonators, which is currently being introduced into surface blasting applications. The rationale for developing the SURBS was to meet key needs of mine operations, such as minimizing the shutdown time and the capability to conveniently initiate blasts in difficult terrain from a safe distance. Increased distance from the blast site, combined with a good overview of the site enables maximum safety during blasting. The system also removes the inconvenience of running long firing cables. The SURBS consists of the field-proven detonator and equipment technology of an existing electronic detonator system, a Surface Remote Blasting Box and a Surface Remote Blaster. The Surface Remote Blaster is the Master unit and controls the Remote Blasting Box via encrypted radio communication using a sophisticated safety technology, which guarantees that the highest safety standards are maintained.

Jan 1, 2005

By John Starkey

"During the period June 2007 to March 2007, John Starkey of Starkey & Associates (Starkey) worked in Russia for High River Gold, supervising the engineering design work that was being done at the IRGIREDMET Research Institute, in Irkutsk Russia. The work entailed moving the Newmont No. 4 mill from Elko, Nevada to Berezitovy, a mine site north and west of the city of Skovorodino, in the Amur Region of Siberia. This was a grass roots project and required construction of all phases of the infrastructure and process facilities that are associated with a 5000 t/d open pit mine and CIP mill.During the course of this engineering design exercise, many aspects of doing business in Russia were encountered, with regard to laws, norms, and business practices. This paper discusses many of these findings. Also by living in Irkutsk, many observations on Russian life and social customs were made and these merit discussion from a general interest point of view.Prior to going to Russia, another engineering and ore testing firm (TOMS) had approached Starkey to find out if Starkey could assist them in upgrading their SAG ore testing procedures to Western standards in order to offer their clients turnkey projects, that included reliable SAG and AG grinding. TOMS was aware that Starkey had invented the SPI test but did not know that the SAGDesign test had by then been fully developed and was being offered commercially as the most accurate way in the world to design new grinding mills. They were also unaware that this new testing method had been patented by Outokumpu (now Outotec) and that this method allowed them access to a design method, through Starkey, that would lead to a manufacturer’s guarantee (by Outotec) of throughput and grind for any new semi-autogenous or autogenous grinding circuit, with or without ball mills.When Starkey started working at IRGIREDMET in June 2005, they also made a request to add a design method for SAG mills that would be considered acceptable to Western clients. From these requests, presentations were made in Russian to both institutes and each decided to join the SAGDesign Consulting Group as satellite members and buy a SAGDesign test mill to use with their Bond Ball Mill Work Index mills, to provide SAGDesign testing services. To complete the service, contracts have been put in place for Starkey to use these results to design new grinding equipment and to train engineers at TOMS and IRGIREDMET how to do this work.Starkey also undertook to train engineers at both labs to go into the field and to take the samples for SAGDesign testing programs. It is here where the SAGDesign testing service upgrades other grinding test programs because the samples to be used for design are professionally chosen, and the results will be much more likely to produce a satisfactory design. Starkey is a mining engineer and is uniquely qualified to do this task. This and the SAGDesign test are the key components that lead Outotec to offer a performance guarantee for mills designed by Starkey."

Jan 1, 2008

By J. C. Yingling, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Much of the land reclaimed since enactment of the 1977 Surface Mining Control and Reclamation Act is over-compacted. Research has shown that excessive compaction in replaced growing media is detrimental to establishment of trees. If trees are to be grown on reclaimed surface mined sites, something must be done to alleviate this excessive compaction. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed growing media. The University of Kentucky has developed test cells on reclaimed sites at a surface mine in eastern Kentucky to determine the impact of tillage (ripping) on soil compaction and tree survival rate. The ripping methods being evaluated include shallow tillage using conventional farm equipment and deep tillage using a dozer with a ripping arm. The impact of organic soil supplements on soil physical properties and tree survival rates is also being evaluated at the site. The organic soil supplements being evaluated include application of hardwood bark and application of straw and mulch. Each test cell has been planted with various species of trees, and for the first two years, data have been collected at these test cells for soil dry bulk density, penetration depth and resistance, and survival rate of trees. These data are currently being correlated to determine how ripping and the application of organic soil supplements affects the relationship between soil compaction and tree survival rate.

Jan 1, 2002

By Gorzalczynski. Stan

The recent trend in underground mine developments is ?big is better?. This is most certainly evident in the mine shaft and the conveyances that operate within its compartments. Today, there are several new installations requiring mine cages that can transport up to 170 passengers. The technology in mine hoisting is advancing to address a combination of higher capacity requirements, deeper hoisting depths and faster winding rates, however, some areas of the hoist plant have not changed for the past fifty years. The most notable of these areas is the shaft compartment guide string and the conveyance mounted safety arrest mechanism. The technology in use today for the protection of passengers in a shaft conveyance from a hoist rope severance incident, remains conceptually unchanged from Elisha Otis? design of 1850. The actual retardation components, the safety dogs, have taken on several forms since Elisha?s invention with the last major design change occurring in the late 1940?s. The arrest of a free falling shaft conveyance requires that the shaft guides withstand the energy imparted on them by the safety dogs. There are some very real limitations presented by the use of wood for this application. The new hoisting era will most certainly continue to demand larger capacity equipment but also, an increased awareness toward safety.

May 1, 2002

By Ray W. Ballmer

"For his leadership in developing and managing large, complex, and technically innovative mines, particularly the outstanding and successful Bougainville mine and for his lecture, 'The Moving Targets of Mine Development '. " Recipient of the 1981 D. C. Jackling Award

Jan 1, 1982

By Dennis R. Dolinar, Gabriel S. Esterhuizen

In this National Institute for Occupational Safety and Health (NIOSH) investigation, numerical modeling is used to evaluate the degree the pillar strength is increased with a rectangular pillar over a square pillar. Three-dimensional models are developed with pillar sizes and geometries typical of underground limestone mines in the United States. Physical properties for the models are based on geotechnical surveys of nearly 30 underground limestone mines. To examine the effects of pillar length on pillar strength with the modeling, a parametric study was conducted where the pillar width was held constant while the length and height were varied resulting in width-to-height ratios ranging from 0.5 to 1.5 and width to length ratios ranging from 1 to 6. There are two aspects to pillar strength and failure. At relatively low stresses, pillars can fail as a result of geologic structure. At greater depths and sufficient extraction ratios, the pillars can also fail as a result of the vertical stresses exceeding the pillar strength. The effects of increasing pillar length regarding both strength aspects are presented in this study. Equations were developed for the increase in pillar strength with both height and length based on the model results. The results from these equations were compared to those from previously developed empirical equations for rectangular pillars. For the more slender limestone pillars with a width-to-height ratio below one, there is little increase in pillar strength for length-to-width ratios above 2 and almost no increase with length for a width-to-height ratio of 0.5. Only with the more squat pillars is there a significant improvement in strength with length. The gain in pillar strength with length for the pillars is explained by the change in the ratio of the area of the pillar affected by the ends to the area of the pillar. For the squattest pillar, the change in strength is also affected by an increase in pillar confinement along the central length of the pillar as the pillar transitions from a square to a long rectangular pillar. With geologic structure, added pillar length can significantly improve the pillar strength, depending on the strike of that structure with respect to the long pillar axis.

By P. R. Desam, J. D. Miller, A. Datta

The flow behavior of bubble-particle aggregates in separation tanks is important for many flotation systems, particularly for wastewater treatment. These aggregates can be considered as the dispersed phase in a continuous liquid phase of water and the flow characteristics determine the efficiency of the bubble separation process. In this work, a general methodology for the computational fluid dynamics (CFD) simulation of a bubble separation tank is described. This system is analyzed by Eulerian-Lagrangian approach. The momentum transfer from the dispersed phase to the continuous phase is quantified using the Particle-Source-In Cell (PSI-Cell) method. With CFD simulations, the effectiveness of different tank design parameters are evaluated in terms of the extent of bubble separation.

Jan 1, 2000

A new personal respirable dust monitor developed by Rupprecht & Patashnick Co., Inc. in a multi-year project funded by the National Institute for Occupational Safety and Health (NIOSH) generated promising results in underground coal mine testing performed by NIOSH and industry representatives during the summer of 2003. The mine data showed that the personal dust monitor (PDM) performed similarly to co-located manual reference samplers for full-shift samples at all four underground coal mines at which the evaluation took place. The technology that forms the heart of the PDM, called the tapered element oscillating microbalance (TEOM system), is unique in its ability to collect suspended particles on a filter while simultaneously determining the accumulated mass with National Institute of Standards and Technology traceability. Because the monitor measures the true particle mass collected on its filter, its results do not exhibit the same sensitivity to water spray as do optically based measurement approaches. The technique achieves microgram-level mass resolution even in the hostile mine environment, and reports dust loading data on a continuous basis. Using the device, miners and mine operators have the ability to view both the cumulative and projected end-of-shift mass concentration values, as well as a short-term 15- or 30-minute running average. During underground mine trials in the summer of 2003, technical personnel used the readings from the PDM to identify and correct several abnormal dust generating scenarios. These events demonstrated the potential of the PDM to be used as an engineering tool to evaluate the effectiveness of various dust control strategies. In a separate evaluation performed by CONSOL Energy, Inc., the mine operator evaluated the benefit of a proposed new water spray-based dust control system. Engineers measured the dust concentration upstream and downstream of a production location under different dust control scenarios using two PDM units. By evaluating the change in the dust loading between the upstream and downstream monitoring sites, the company was able to determine in a few hours which hardware configuration would yield the greatest benefit to the workplace environment. BACKGROUND Measuring underground coal mine dust concentrations is an essential part of protecting miners' health. The U.S. Secretary of Labor and the Federal Advisory Committee on the Elimination of Pneumoconiosis among Coal Mine Workers has recommended that better monitoring of coal miner dust exposures be used as a method to improve miner health. In consultation with labor, industry, and government, NIOSH issued a contract to Rupprecht & Patashnick Co., Inc. (R&P), Albany, N.Y., to develop a one-piece PDM. The object was to miniaturize TEOM technology into a form suitable for a person-wearable monitor that would enable accurate end-of-shift dust exposure information to be available to miners. Furthermore, any person-wearable dust monitor should minimize the burden to the wearer by incorporating the monitor into the mine worker's cap lamp battery, with exposure data continually displayed during the shift to enable workers and management to react to changes in dust exposure. In the summer of 2003, NIOSH conducted extensive testing of the PDM to determine its laboratory and in mine performance. In addition, anecdotal information collected in the mines showed several occasions where miners were able to identify situations that produced high levels of respirable coal mine dust The PDM's response to unplanned changes resulted in action being taken to keep dust exposures as low as possible. In another case that demonstrated the PDM's versatility, a mine was seeking to find a better dust control solution on its longwall headgate stageloader. In this instance, the PDM was used as a diagnostic tool by the miners to quickly evaluate the control technology. [ ] HOW DOES THE PDM WORK? The PDM is configured to provide accurate respirable dust personal exposure information in a form that is as convenient to wear as a normal cap lamp (See Figure 1). Respirable dust exposure data displayed by the device has two main objectives: providing the miner and mine operator with timely values to avoid overexposure to dust, allowing them to make any necessary changes during the course of a work shift; and computing an accurate end-of-shift statistic for a miner's average respirable dust exposure. The mass sensor embedded in the PDM, holds the key to the accurate, time-resolved dust concentration measurements. The inertial, gravimetric-equivalent, mass measurement technique used in the device typically provides a limit of detection on par with that of the most sensitive laboratory-based microbalances.

By C. W. Spencer, J. T. Smith

GRAIN-BOUNDARY surfaces are penetrated by a liquid phase when the liquid-solid interfacial tension is less than one-half the tension of the grain-boundary surfaces. Grain growth may occur in the presence of this liquid phase. burke1 reports that grain growth of this nature has been observed in two-phase ceramic systems. He suggests that the presence of a grain-boundary liquid may accelerate or decelerate the

Jan 1, 1963

In 2004, a total of 741 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). These mines (e.g., potash, gypsum, salt) comprised 5.1% of all operations.

Sep 1, 2007

By G. A. Apell

"SUMMARYThe quality of Moose Creek coal is considered superior to that of any now being produced in the Matanuska field of Alaska. In rank it is classed as roar coking high-volatile B bituminous coal.At present the Moose -Creek mines are accessible from the Glenn highway by 6 miles of well-maintained gravel road. The nearest railroad loading point is Moose Creek siding; 7 miles by road from the Buffalo mine. Palmer, 12 miles south of Buffalo mine, is the nearest town. Anchorage is 50 miles south of Palmer by road and-railroad.Core drilling and trenching by the Bureau of Mines revealed 2,375,500 short tons of coal in the Buffalo series on the Buffalo Coal Co. leasehold. Of this, 514,200 tons is considered measured coal and 489,900 tons indicated coal. Existence of deeper beds over the same length increased the tonnage of coal of all categories to 3,279,300 tons. The property has an assumed life, of 16 to 22 years, depending on the number of beds mined, based on an output of 500 tons of coal a day and 100-percent recovery. Coal from some of the beds car be marketed without washing however, a washery is necessary if all beds are mined. Beds in the Buffalo series not mined in the ""first mining"" will be irrecoverable at any later date.The Bureau of Mines completed exploration of approximately one-third of the local coal-bearing areas during 1943. Knowledge gained from this work makes it possible to investigate the rest of the area by drilling an estimated additional 5,000 foot of hole."

Dec 1, 1944

Mineralisation was identified at Gladstone Hill as far back as the late 1870s-early 1880s, shortly after the initial discovery of mineralisation at what is now the Martha Mine. Indeed, early recovery problems associated with the Martha mineralisation led to the preferred development of ore bodies within what is now the Union Hill Joint Venture tenement; ore bodies such as Silverton, Amaranth, and Union to name a few. Gladstone Hill forms the basis of the Union Hill Joint Venture, a 50:50 joint venture managed by Au-Ag Resources Ltd (a fully owned subsidiary of Otter Gold Mines Ltd), and Welcome Gold Mines Ltd (a fully owned subsidiary of the Normandy Group). The joint venture participants also operate the adjacent Martha Mine. Mineralisation of Gladstone Hill, as with mineralisation at the adjacent Martha Mine, has been interpreted as a low sulphidation epithermal Ag-Au system hosted within hydrothermally altered andesites of the lower Coromandel Group. Drilling in recent years has successfully identified extensive mineralisation associated with a number of vein sets throughout the tenement including the Gladstone Vein set, the Moonlight Lode and more recently along a north-easterly trend towards the historic Favona workings. A wide range of vein styles is apparent, ranging in character from thin stock works to broader lode-style banded chalcedonic to cherty quartz and have been interpreted as representing multiple phases of emplacement. At shallower levels mineralisation is often hosted by vein clasts within vent breccias. Visible gold is rare, with mineralisation generally associated with very fine-grained pyrite, arsenopyrite and minor electrum. Percentage levels of combined sphalerite-galena-(+/- chalcopyrite) have been intersected at depth however these have been gold poor to date. The potential for the Gladstone Hill area remains to be clearly defined as drilling to date has yet to close off mineralisation both along strike and down dip. If further drilling is successful, the joint venture partners believe Gladstone Hill could contribute significantly to the economic future of current operations.

Jan 1, 2000

By Jerry E. Olson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 20,071-acre South Fork Wilderness Study Area (OR-005-033) and part of the 8,791-acre Sand Hollow Wilderness Study Area (OR-005-034) in order to evaluate their identified mineral resources. The study areas are located in Crook County, OR, about 58 air miles east from Bend. The areas studied are underlain by Tertiary- and Quaternary-age volcanic and tuffaceous sedimentary rocks. No mineral resources were identified in or adjacent to the study area. Except for common opal and agate occurrences along the northern boundary of the study areas, no mines, prospects, or mineralized zones occur within the study areas. Bentonite is periodically mined less than 1 mi southwest of the Sand Hollow study area boundary. Neither of the study areas has geothermal leases, but both areas are under lease for oil and gas.

Jan 1, 1987

By B Bamford

High speed diamond cutting has extensive applications in civil and mining engineering. A project involving the diamond sawing of black granite is investigating the nature of the diamond cutting process. A sawing machine was devised to adjust the cutting load and measure cutting speed. Cuttings were collected for size distribution analysis. The surface produced by interaction between diamond. grits and the rock was subjected to microscopic investigation. Increasing load prompts the proportional increase in the cutting rate. But the mean size of cuttings shows little change. The photomicrographs of the cutting tracks indicate neither patterns of crack formation nor signs of the ductile behaviour of the rock. A diamond cutting model for hard rock is formulated on these observations. Diamond cutting is a process of surface failure, which advances in four stages. The polycrystalline characteristics of a hard rock and the action of high-speed diamond grits guarantee the creation of crack nuclei which develop into cracks in various directions. This network crisscrossing cracks enable the stripping of this surface layer from the rock.

Jan 1, 1992