Search Documents

By C. Melvin Lepper

The Bureau of Mines has developed an improved earth resistivity field system which employs a novel technique for obtaining null measurements. The instrument is designed to operate reliably in high-noise environments such as those found in the vicinity of operating mines. The system consists of a low-frequency transmitter, a sensitive receiver and an external battery pack, each in its own case to provide protection from the elements. The receiver and transmitter units have self-contained recharge-able batteries to supply power to the circuitry and separate built-in battery chargers that operate on standard 115 Vac power. The system is portable and simple to operate. Measurement accuracy, reliability, and dynamic range are superior to most commercially available equipment even though less time and effort is required to make null readings. Unlike some commercial systems, long integration times are not required to enhance signal-to-noise ratio in areas of high background noise.

Jan 1, 1974

By D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the U.S. Department of the Interior, Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows were continuous except for short periods when resin increments were withdrawn. The exchange of uranyl carbonate between a simulated in situ uranium leach liquor and a strong-base ion-exchange resin together with the subsequent elution with an ammonium chloride solution was studied. The effects of the number of sections, section height, amount of resin withdrawal, solution flow rate, and column diameter were investigated. The kinetic and equilibrium relationships for the absorption and elution steps were also examined. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable in the absorption process, while resin residence time is the determining factor in the elution process. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1978

By T. C. Green

A two-phase program evaluated commercial proximity warning devices and then served to design and develop an automatic electrostatic field strength measurement device with improved performance. The Phase I program consisted of test and evaluation of three commercial proximity warning devices, all of which operate on the principle of electrostatic field intensity measurement for determining proximity to high voltage power lines. Performance testing of these devices utilized full-scale cranes and power line systems and a scale model facility. The evaluation results were reported in the Phase I report entitled "Evaluation of Proximity Warning Devices" dated 22 February 1980. Under the Phase II program, a microproressor-based data acquisition system was designed and developed to collect and measure field strength at distributed points around the crane boom. This unit (referred to as the Distributed Sensor AC Electrometer) measures the field strength about a crane boom using 17 distributed sensors. Keyboard control is provided for the equipment operator. Measured field strength values are displayed on a line printer and recorded on magnetic tape. Laboratory testing of this unit demonstrated performance characteristics and field strength measurement accuracy within the design goals. A Phase III measurements program is proposed using the AC Electrometer to map the field strength contours about power line configurations.

Jan 1, 1981

By Robert L. Lagace

This report describes the results of a system study of the factors influencing mine rescue attempts based on the use of electromagnetic VF rescue transmitters by trapped miners and helicopterborne search receivers by mine rescue personnel. The findings cover four main task areas. The first - mine emergency/disaster considerations - concentrates on characterizing the events and key parameters of mine fires and explosions related to trapped miner location and rescue activities. The parameters include critical time periods, affected areas, survival times, response and rescue times, and survival rates. The second - hardware considerations - concentrates on characterizing the relevant properties of VF rescue transmitters, oxygen-type self-rescuers, VF search receivers, helicopter performance, and signal detectability and sensor sweepwidths for helicopterborne sensors. The third - search theory probabilistic model develops a method to identify the most important regions to be searched, and to allocate helicopter-based search effort so as to maximize the number of miners detected in time to be rescued. The fourth - sensitivity analyses and application of the search model - exercises the search model on representative mine emergency/disaster scenarios to assess the impact and effectiveness of helicopter-based searches. Conclusions and recommendations are presented, together with a set of search scenario planning guidelines.

Jan 1, 1982

By D. M. Milne, P. J. Lunder, R. C. Pakalnis

During the mining of an open stope, deformation of the hanging-wall and the potential for dilution generally increase with the size of the exposed hanging-wall. Excluding discrete structures that may delineate unstable blocks, the mechanisms that drive hanging-wall deformation and possible dilution comprise several factors which can include elastic, plastic and discontinuum deformation. These stages of deformation are not mutually exclusive and at any point during mining all three of these mechanisms may be acting on the hanging-wall rock mass. Computer modelling techniques are available to analyse the three stages of deformation, but the difficulty lies in trying to obtain realistic rock mass properties for input and in determining when each stage of deformation is acting. Instrumentation data can be used to predict the effect of continued mining. However, it is often difficult to calibrate numerical models against field data owing to the large number of input parameters required. An empirical approach is recommended that uses two new parameters, the radius factor and the effective radius factor. A method is proposed for predicting the effect of continued mining from existing deformation and dilution data for a given hanging-wall

Apr 1, 1996

By Wallace W. Roepke

The Bureau of Mines conducted a series of experiments using Illinois No. 6 coal to determine the effect of asymmetric wear on airborne respirable dust (ARD), specific energy, cutting force, and normal force. Plumb-bob-type bits--one new bit and four ground with different sized flats--were used. Constant-depth linear cuts at 0.32, 0.64, 1.27, and 2.54-cm cut depths were made. Both cutting force and normal force increased as the flat area increased. Specific energy demonstrated a statistically significant increase with flat area at the 0.32-and 1.27-cm cut depth only. Specific ARD showed a statistically significant decrease with increasing flat area only at the 0.64-cm cut depth. Increasing cut depth increased cutting force but decreased specific energy and specific ARD. Normal force increased with increasing cut depth for the new bit but exhibited a maximum at 0.64 cm for the bits with flats.

Jan 1, 1983

By G. Luttrell, S. Keles, M. Eraydin, R. Yoon

The dewatering of fine particles is energy intensive and often requires costly capital expenditures. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids that enhance the performance of existing filtration equipment and an innovative hyperbaric centrifuge that utilizes both air pressure and centrifugal force for dewatering. The moistures obtained using these processes are 30-50% lower than those obtained using conventional methods. Another dewatering technology, known as the hydrophobic displacement process, can reduce product moistures to a level previously attainable only through the use of thermal dryers. This article presents test results obtained with these various advanced dewatering technologies along with estimates of the power consumption for each process.

Jan 1, 2007

By L Lorenzen

In this paper, we developed and implemented a fuzzy logic expert system capable of evaluating the degree of sustainability within the context of gold mining operations. The newly introduced approach of evaluating sustainability in the gold mining industry has the merit of sufficiently handling diverse, sustainable, development-related qualitative and quantitative data owing to fuzzy logic technology capabilities in dealing with linguistic syntax. The economic, environmental and social indicator inputs were independently evaluated and then combined with the aid of fuzzy logic to provide an overall sustainability index on a scale of zero to one. A total of 66 independent indicators were identified and applied in our model. The novelty of this work lies in providing a coherent numerical and automated approach in evaluating sustainability in the context of gold mining operations. In addition, the model can aid policy- and decision-makers in arriving at consistent decisions regarding the degree of sustainability on various aspects of gold mining operations. The functionality of this model will be illustrated through several examples.

Jan 1, 2007

A series of in situ pull tests has been conducted to determine the holding capacity of the standard SS46 Split Set Stabilisers. The experiments have been conducted in a wide range of geological conditions ranging from bedded rock to blocky ground. The results presented in this paper indicate that cement grouted split sets bolts are likely to provide up to three times the initial bond strength per metre of embedment length provided by the ungrouted bolts. The increased load transfer capacity of the grouted bolts provides an alternative for permanent excavation support using split set stabilisers.

Jan 1, 1997

By P. Klaus

"KfW IPEX-Bank is the commercial arm of KfW Bankengruppe, responsible for international project and export finance.KfW was one of the first banks in Germany to promulgate environmental guidelines for its commercial business activities. These guidelines were first made public in 2000 and updated for the second time in 2004. They now include specific reference not only to environmental but also to social concerns. The guidelines specify the procedures to be followed in assessing credit risks related to environmental or social hazards.The bank considers sustainability as an interdependent framework of economic, ecological and social factors. In its efforts to contribute to sustainable development worldwide the bank uses its influence as far as possible to improve a project’s performance if such improvement is deemed necessary."

Jan 1, 2005

By Valery M. Paretsky

The effect of the degree of nickel oxide reduction and the reaction gas composition on the furnace productivity has been estimated by computations and the established relationship is in good agreement with the practical data obtained in the process of electric smelting at the Severonickel smelter. An increase in the reduction degree within a range of =0.65 - 0.9 results in an increase in the furnace productivity by 19% to 37% and in a decrease in the unit electric power requirement by 16% to 27% depending on the reaction gas composition. The agreement between the computed and practical data has confirmed that the decisive factor for the process of treatment of reduced nickel oxide in an electric-arc furnace under the given conditions is the specific heat absorption, which is dependent on the nickel oxide reduction degree and the reaction gas composition.

Jan 1, 2005

By R. Graeme, J. Komadina

Gold Fields acquired an option to purchase the Cerro Corona Project, located in Hualgayoc, Cajamarca Department, Perú, in December 2003. In January 2006, the option was taken up and the transaction closed. During the intervening months, Project development occurred against the backdrop of a Presidential election, increasing national social activism and environmental regulation, rapidly escalating operating and capital costs, as well as unprecedented demand for engineering and technical skills. Project “Lessons Learned” are outlined and discussed in the context of an evolving strategy.

Jan 1, 2007

By József Faitli, Barnabás Csoke, Károly Solymár, Zoltán Hatvani, Dimitri Papanastassiou

In most cases, the sizing of dry or wet mills for ore processing is primarily based on the determination of the Bond grindability index, using the Bond-Kjos-Rowland relations. In several cases, grinding takes place under conditions different from these and the grinding conditions have a great influence on the postgrinding process. This is particularly true for the grinding of bauxites where grinding takes place in alkali, often in higher temperature in alkali Liquor. So it is necessary to develop a testing method providing a reliable grindability index even under these special circumstances and allowing a more precise mill sizing. Therefore we surrounded the grinding crucible of the Hardgrove mill with a crucible furnace to heat it. The new heated mill is suitable to determine the grindability index under temperature-controlled circumstances, in liquids (water and alkali) with different temperatures. The required heating power is 2000 W. In the implemented equipment we installed four 230V/500W electric heating wires made from heat-resistant alloyed material and surrounded by ceramic insulators. The temperature and temperature-gradient are measured by four PT100 platinum thermal resistors. The data acquisition and control program written in the C language in the Lab Windows CVI program environment measures the voltage proportional to the temperature. Determining the grindability indices of hungarian and greek bauxites experimentally, first dry grinding tests were carried out under standard conditions. During wet and alkaline grinding, to 50 g of dry bauxite 85.5 g of industrial alkali with a concentration of about 200 g/l was added. As grinding aid 2 g of CaO (4 % of dry bauxite) was dosed. From the data it can be concluded: - The tested bauxites show a similar behaviour against temperature change. However, the extent of grindability change is different for different bauxites. - Soft Hungarian boehmitic bauxite can be ground in a high-temperature alkaline medium better than hard Greek one. The increase of grindability according to the high-temperature Hardgrove indices: (kHT = Dry o HT,alkaline H /H ): for hard Greek and soft Hungarian boehmitic bauxites: kHT = 1.7 and 2.4 respectively; according to estimated Bond indices (kB,HT =Wi,dry/Wi,HT, alkaline ): kB,HT = 1.6 and 2.1. - The increase of grindability is the most important factor the reaction of kaolinite with caustic liquor and lime and the loosing of the textural structure at 80 ºC and especially at 100 ºC.

Jan 1, 2003

By Kunihisa Katsuyama, Yuji Ogata, Yuji Wada

The one free surface blasting of a concrete block was simulated by Discontinuous Deformation Analysis(DDA) method. Comparing the simulated results with the concrete block blasting experiment, the crack growth and the free surface displacement which were simulated by DDA were observed with a high speed camera.

Jan 1, 1996

By R. J. F. Goodfellow

Many underground projects now include preparation of a Risk Register through planning and design as a tool for project and risk management. There is still significant discussion within the industry as to whether and how to best present the Risk Register through the bidding process and the construction phase of a project. While the ITIG Code of Practice for Risk Management of Tunnel Works recommends this approach of continuity in risk management procedures, it is silent on the specifics of how this should be achieved. This paper will explore the perceived benefits and disbenefit of including the project Risk Register with bid documents; format and content that should be transferred and lessons learned using the case history of bidding and early construction phase of the Bi-County Water Tunnel in Montgomery County, MD

By V. K. Gupta

"Effect of mill speed on grinding kinetics has been investigated with a view to using mill speed as a manipulated variable for control and optimization of the grinding circuit performance under variable ore hardness conditions. Dry and wet batch grinding tests were carried out for quartz, limestone and cement clinker in a 29 cm x 18 cm laboratory ball mill. Mill speed values selected were 55 and 70% critical. In the case of dry grinding operation, with an exception of quartz, for all materials studied the effect of mill speed on grinding rate was found to be insignificant for sizes finer than about 35 mesh. In the case of wet operation, grinding rates were found to be approximately proportional to the mill speed. The implications of these results are discussed.INTRODUCTIONIt is well known that mill speed has a considerable effect on the grinding rate of the ore particles l-3 For particles of a given size there is an optimum speed at which mill grinding efficiency is maximum (i.e. specific energy consumption is minimum) 3•4. Mill speed can, therefore, be effectively used as a manipulated variable to deal with the disturbances arising from changes in the size and hardness (grinding rate) of the ore being fed to the grinding circuit. Though, it has not been the case so far, with recent developments of ring motors2 and frequency inverters5 a continuous variation of mill speed has now become feasible, and it is expected that mill speed control will soon be a regular feature of plant operation2,6."

Jan 1, 1985

Newmont Waihi Operations is participating in the initiation of a community liaison forum in association with the local district council. The objective is to provide a forum for the free and regular exchange of ideas, concerns and information, and through improved communication seek to achieve a more comprehensive set of solutions to community, operating and closure issues associated with Martha Mine. A similar liaison forum has been operated on two previous occasions during earlier phases of the present mine's operation. This paper deals with the practical aspects of setting up a liaison forum to act as an effective conduit between regulators, mine operators, local businesses and the community. The mechanisms and procedures for identifying community issues and concerns are dealt with. The actions and structures required to ensure effective ongoing community 'buy in' at all levels are discussed. Corporate philosophies are addressed. Specific examples from Martha Mine, Waihi New Zealand will be used to illustrate the paper. This will include a brief explanation of previous and current community issues, Newmont Waihi's operations both at Martha Mine and the proposed Favona underground mine, and the practical issues involved in setting up a liaison forum.

Jan 1, 2003

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 49,875 acres of the 54,833-acre Big Jacks Creek Wilderness Study Area (ID-111-7C) in order to evaluate the mineral resources. The study area is located in Owyhee County, ID, about 15 miles southwest from Bruneau, ID. No mining districts are in the study area, but part of one placer claim, located in 1924, extended into it. The northern portion of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Big Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By R. G. Peluso

Methods and results of studies to determine friction and shock losses encountered in auxiliary face ventilation systems utilizing flexible, spiral-reinforced ventilation tubing are presented. The results, tabulated in graphic form, simplify fan selection and enable mine operators to design adequate auxiliary ventilation systems. Problem illustrates the use of graphs.

Jan 1, 1968