Search Documents

By K. Lundholm, M. Andersson, L. Nevatalo, Å. Holmström, L. Hedström

"Several copper deposits have the arsenic bearing minerals enargite (Cu3AsS4) and tennantite (Cu12As4S12). Since this mineral contain both arsenic and copper, it is not possible to remove the arsenic by selective flotation. Partial roasting is a method to clean the concentrate from arsenic and thereby produce a suitable raw material for the copper smelter. Also mercury is commonly found in copper bearing minerals. In the partial roasting process both arsenic and mercury are volatilized, while part of the sulphur is used as energy during the roasting. This gives a calcine suitable as feed to a smelter, much like an ordinary copper concentrate. A typical analysis of calcine would be: S content 18–22%, As content below 0.3%, Cu content – not affected, grain size – not affected. However, if the concentrate contains mercury, the mercury will be volatilized during the roasting process. This will lead to very high mercury contents in the subsequent process of sulphuric acid, unless the SO2-rich process gas is pre-treated by the Boliden/Norzink process that recovers mercury as calomel, Hg2Cl2. The volatilized arsenic in the gas phase can be recovered either by dry or wet methods. However, one problem is that arsenic also contaminates the fine grained calcine dust that is captured downstream in the gas cleaning system. The calcine dust contains valuable metals such as copper, gold and silver that needs to be separated from the arsenic. The ultimate aim is to stabilize the recovered arsenic as a compound with minimum impact on the environment and recover the valuable metals. By using wet recovery methods it is possible to selectively precipitate copper, gold and silver as sulphides while arsenic is kept dissolved in the liquid. The precipitated metal sulphides can be mixed with the calcine and sent to the copper smelter. The dissolved arsenic is sent to effluent treatment and is further treated in Outotec ferric arsenate precipitation process, where arsenic is precipitated as the stable compound basic ferric arsenate, formula FeAsO4·xFe(OH)3. All concentrates containing arsenic are unique and the process design of a roaster plant must be based on relevant process data. The process data is collected during tests in lab scale and pilot scale, where the influence of critical process parameters on the quality of calcine is studied. The ability to run tests both in lab scale and pilot scale is crucial to the development of the correct roasting process. Outotec is well equipped for this."

Jan 1, 2014

By E. Wasmund

"Sandfire’s DeGrussa Copper-Gold operation in West Australia is a new high grade copper sulfide mine, which includes a 1.5 Mtpa concentrator which was completed in 2013.Early after commissioning, it was identified that the flotation capacity in the all-mechanical cleaner circuit was not sufficient. In order to improve recovery, the tail from the cleaner scavenger was sent back to feed the rougher scavengers. Test-work was done on-site to evaluate the possibility of using a flotation column as a pre-cleaner. A CavTube™ sparging system was selected, which is especially effective for fine ore particle flotation. Test-work was conducted at site using a 150 mm diameter unit, and then confirmed on a 500 mm diameter unit. A 4250 mm diameter full scale unit was installed in Q4 2014 and commissioned in Q1 2015. This unit gave some significant advantages including a reduction in re-grinding requirements, elimination of a circulating load and increase in the recovery of copper in the cleaner circuit and overall circuit.In this presentation, the benefits of columns and cavitation sparging for floating fine particles and rejecting fine entrained gangue will be explained. Also, the results from a lab unit and a pilot unit will be compared against the results of the full-scale unit. The paper will demonstrate the scalability of flotation columns, and which phenomena and scale-up criteria must be considered to be successful. Finally, some general observations will be made about the importance of columns in copper cleaning circuits.IntroductionSandfire Resources’ DeGrussa copper-gold concentrator is located approximately 900 km north-north-east of Perth in Western Australia. The project area landscape is scrubby mulga lands with few notable features. The climate is arid with high temperature and heavy summer downpours."

Jan 1, 2016

Determine the advantages and operational limitations of water-let-assisted cutting used with mining equipment. Approach The Bureau of Mines con-ducted a research study to evaluate water-Jet-assisted cutting both in the laboratory and in underground mines. Earlier research on water-jet-assist was limited to laboratory studies where bit speeds and penetration depths were very low and large cutting force reductions were reported. For the past years, research by the Bureau of Mines and others has been concerned with the application of water-jet-assisted cutting under more realistic mining conditions. Study Results Water-jet-assisted cutting employs a mechanical cut-ting bit combined with a moderate to high-pressure water jet directed just in front of the bit tip to assist in the cutting process. Recent Bureau findings show that the addition of the water jet to the cutting bit can improve cutting in harder materials, significantly reduce respirable dust and bit wear, and increase product size. Some of these findings are presented as follows.

Jan 1, 1987

By D. E. Wolfson

As part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests. According to the estimate of reserves by Dowd,3/ the recoverable coal in Raleigh County in beds 28 inches or more thick, in thousand tons, is: [ ]

Jan 1, 1957

Flow Sheet Simulation of Municipal Waste Treatment Processes

Sep 13, 2010

By C. H. Titus

This study consists of four descriptive Sections covering respectively: a state-of-the-art literature survey on ungrounded and grounded power systems, a report on literature pertaining to human threshold limits of electric shock, an analysis of the performance requirements of isolated systems and a section on design and performance specifications for an isolated system the final section includes copies, and translations where applicable, of the most important articles on foreign mining practice as well as some technical publications which could be difficult to obtain elsewhere. Section 2 - Literature Survey In analyzing the available literature on ungrounded systems it became apparent that too strict an interpretation of Section 1.1 of the Contract would limit the survey in both period of time analyzed and in available literature which discussed several types of power systems. Therefore, the survey was expanded to cover approximately the past twenty-year period and to cover literature which addressed itself to both ungrounded and grounded power system operation. Section 2 gives a brief summary of this literature survey and lists the important papers and books which were examined.

Jan 1, 1972

By Roger E. Burleigh

In June, 1989, the U.S. Bureau of Mines, undertook a 9-day evaluation of the tin resource potential of the Sleitat Mountain tin deposit. Significant tin-tungsten mineralization is associated with quartz-topaz-white mica-tourmaline greisen alteration of a multi-unit, 57 Ma, peraluminous, granite stock which intrudes Cretaceous Kuskokwim Group flysch deposits. The granite comprises marginal biotite-, intermediate biotite-muscovite-, and central zinnwaldite-granite units, interpreted as a zoned alteration system. Major vein mineralization is confined to two east-west-trending zones of steeply oriented tabular lenses of greisen interleaved with mildly altered granite. Cassiterite is the dominant ore mineral while arsenopyrite, loellingite, wolframite, pyrite, sphalerite, chalcopyrite, and bismuth-oxides are present in minor to trace amounts. The north and south greisen zones are estimated to contain an inferred resource of 128 to 212 million lbs Sn in 28.6 million st of mineralized rock. An 1,800-lb representative bulk sample contained 0.37% Sn, 0.04% W and 17 ppm Ag and is considered an average grade estimate for the deposit. Drill testing by Cominco Alaska Exploration indicates that substantial widths of high-grade tin mineralization are included within the lower grade disseminated mineralization. Depth of deposit erosion is substantial and there exists a high probability for placer tin deposits.

Jan 1, 1991

By H. Morgolin, M. A. Greenfield, P. A. Farrar

In attempts to correlate mechanical properties with microstructure, it is desirable to determine the effect of ß grain size. Determination of 6 grain size is not a problem where a has precipitated at ß grain boundaries. However, in alloys which have been processed to produce an equiaxed a +ß structure the ß grain size is difficult to determine because ß grain boundaries do not etch. The ß grain size can sometimes be laboriously determined by searching for grains which have some a! outlining the 6 grains. This difficulty of ß grain size determination in equiaxed a + ß alloys can be overcome by heating below the ß transus temperature for a short time and water quenching. Fig. 1 shows the starting equiaxed a + ß structure of the Ti-5.25A1-5.5V-0.9Fe-0.5Cu alloy used in this investigation, and Fig. 2 shows the microstructure of the same sample water-quenched after heating 1 min at 1675"F, which is 25°F below the 0 transus. The heavily etched microstructure consists of some equiaxed a! in a structure showing considerable amounts of transformed ß. The ß grain

Jan 1, 1969

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

e Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

By Bruce Vandenberg, R F. Chiappetta

"The High Speed 2D Analysis program allows the user to bring in data from several different sources. Of course, keyboard entry is included as a source. Other data is inputted through the serial port (X-2321 of the PC. Two types of data are transferred via the serial port. The first is the tablet digitizer data. The three types supported presently are the GTCO, tablet digitizers. and the Calcomp 2500 and 9100 series To transfer digitized data turn on the selected digitizer and place the cursor on the tablet. Enter the High Speed pmg.ram and select from the Input Program menu the Digitize Inputs(20) option and follow the instructions. TO exit the session, either a keyboard entry or a cursor button is pressed. The second type of serial port input Is from the collectors of the listed survey systems. Typically a file transfer program will be used to send the data from the collector to the PC. This topic will not be addressed at this time."

Jan 1, 1989

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By S. E. Olsen, T. Færden, G. Tranell, T. Lindstad, J. Lubetsky

The authors are lead authors for chapter 4.3 ?Emissions from Ferroalloy Production? in ?2006 IPCC Guide-lines for National Greenhouse Gas Inventories, Volume 3?. The paper discusses the methods to calculate and report emissions from the production of ferrosilicon, silicon-metal, ferromanganese, silicomanganese and ferrochromium alloys, as well as the basis for the methods and choice of emission factors. CO2 is the main greenhouse gas emission from ferroalloy production, accounting for about 95 % of the total CO2-equivalents. The most accurate method of determining emissions is to base the calculations on reported amounts and analyses of reducing agents and carbonate ores used in the process. If analyses are not available, typical CO2 emission factors for the different reducing agents are recommended. If neither reliable amounts nor analyses of all reducing agents are known, default generic CO2 emission factors for the type of ferroalloy multiplied with amount produced, can be used. The CO2 produced from bio-carbon (charcoal and wood chips) should be reported but will not be accounted for in national emissions. If any bio-carbon is used, the default generic CO2 emission factors cannot be applied. CH4 accounts for less than 1 % of the total emission of CO2-equivalents. Default emissions factors for CH4 are given for the production in open or semi-closed furnaces of silicon-metal and ferrosilicon. In the production of FeMn, SiMn and FeCr in closed furnaces the gas containing CO,CO2 and volatiles can be combusted in boilers and N2O may be formed. While reporting is not required, IPCC Guidelines recommend that the N2O-content in the off-gas is measured.

Jan 1, 2007

By Cceliksirt, V Erkan

This computer program has been developed under the field conditions for use in control of surface drilling-blasting operations. This paper outlines the relevance of fragmentation to quarrying, open pit mining or road cutting and key features and operating principles of the software (DelPat for Windows 95).

Jan 1, 1998

By J. H. Schulman, M. H. Buckenham

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

By W. J. Kennedy, John D. Gardner

Introduction During the past 10 years, energy costs in mining have risen from about 4% to as much as 25% of total production cost. When combined with declining ore grades, these costs exert inordinate stress on mine productivity. Industrial engineering techniques have traditionally been aimed at improving manufacturing facilities productivity, but they have been applied to mining as pressure for productivity improvement has increased. These techniques can perform four useful functions for mining operations by improving methods, equipment selection procedures, energy use through scheduling, and managing energy costs rather than being managed by them. This article discusses some of the standard techniques for productivity improvement, and how they can be adapted to perform these four functions. Pre-Production The best time to seek high productivity is when a mine is being planned. During pre-production, when most options are still open, an optimum mine design is achievable. At this time, major equipment selections are made, the layout, material handling systems, and processes are designed, and critical energy source decisions are made. By including explicit energy cost projections, decisions can be made that will save significant amounts of money per ton of ore over the life of the mine. Attention can also be given to often overlooked details such as lighting. Some of the same tools used in new mine planning are applicable to productivity improvements at an existing plant. These tools are the charting and modeling methods that have been developed by industrial engineers over the past 75 years. Energy Consumption Before any analysis of energy consumption can be performed, preliminary work is necessary to find the kind of energy used, how much it costs the plant, and when electrical peaks occur. Past bills should be examined to determine the monthly consumption rate and the cost of each energy type. These data should be adjusted to remove effects caused by production fluctuations or weather. Knowing when electrical peak demands occur is necessary because these determine either the electrical capacity needed or the amount that must be bought. At $500-$800 per kW for construction or $5-$15 per kW per month for purchase, they represent a significant cost. By the time these data are collected, planners should be aware of the importance of energy in the total cost of mine operation, and should have the most crucial time data for electrical peak demand. Flow Process Chart Reducing costs can be accomplished by a thorough look at mine systems and how altering one system causes changes in others. By developing and exercising models of production processes outward to the transportation of the final product, otherwise obscured weaknesses may become apparent. There are tools available for analyzing the mine and its associated systems; one of the most useful is the flow process chart. The flow process chart gives a system analysis of a production procedure by classifying all actions into one of five types: operations, inspections, transportation, delays without paperwork, and delays with paperwork. Operation: In an operation, the nature of something is changed. Examples are blasting, washing coal, and processing matter. Denoted by 0. Inspection: Examining an object for identification or to measure some attribute. Examples are determining whether a drill hole is deep enough, deciding how far to cut under an unsupported roof when operating a continuous miner, or checking the lubricant level on a truck. Denoted bye. Transportation: Moving an object from one place to another. Examples are transporting overburden, moving coal on a conveyor belt, and pumping water. Denoted by =>. Delay without paperwork: A delay that is an inherent part of the system. Examples include idle time of a continuous miner while waiting for shuttle cars or for roof bolting, crushed ore in a storage area waiting for grinding and flotation, and people from one craft waiting for another craft to finish. Denoted by D. Delay with paperwork: A delay that can be terminated only by some written authorization. Examples are coal that cannot be removed until authorized by a bill of sale and transportation orders, personnel records, maintenance, or spare parts. Denoted by V. In practice, the flow process chart is completed after data collection and a detailed examination of the process. Data collection is needed to answer questions on distance, quantity, and time for each of the operations. As the analysis is being performed, each step of the process is subjected to these questions: • Why is the step necessary? • What is being moved? • When does the step take place, and why?

Jan 11, 1983

By M. Javier

Defining the concept of sustainability is an important step for industry and society. It is necessary in order to clarify what it means when debunking the many misinterpretations pervasive in different levels of anthropogenic activities. Essentially, the extractive industry has a harvest of differences. Mining involves the extraction of natural resources which are finite, exhaustible, non-renewable, unsustainable, and pay only once. It is remarkable that the definition of sustainability that we will shortly arrive at has totally different characteristics from the definition accepted throughout society. We categorize nature as having its own destiny which is controlled by its own rules and principles and its own society, and is part of nature; therefore, society depends on nature and not vice versa as the initial focus. To society there are no conditions to humanize nature but only respect nature?s rules. It was a challenge to find simplicity for this task not only for the definition but also for the explanation of this concept specifically, to answer the question, ?what is the true meaning of sustainability?? Finally, we are also able through this definition to provide fuel for wide discussions and stimulate critical thinking to improve such a concept. As a result, we present this definition as the tool for society today and for future generations.

Jan 1, 2012

By Gerardo Vargas

Without an adequate data sample there can be no Reliability Analysis (RA). Without analysis there can be no systematic, verifiable improvement in reliability or in operational economy. A sample is a collection of life cycles. A beginning and ending event define a failure mode life cycle. Well known obstacles impede the reliability engineer in his role to analyze maintenance data. The main problem lies in the difficulty to obtain analyzable data samples. Although modern Computerized Maintenance Management Systems (CMMSs) should provide the needed information they rarely deliver samples of adequate quality. Cerrejon, an integrated mining operation in Colombia, South America solved the information management problem by applying a "Living Reliability Centered Maintenance (LRCM)" process to its fleets of Trucks, Graders, Dozers, Loaders, and Shovels. This paper describes a method wherein completed work orders capture reliability analysis enabling information. The 'right' maintenance observations reference significant failure modes. Work orders link to records in a continuously growing Reliability Centered Maintenance (RCM) structured knowledge base. Grouped and filtered knowledge-to-work order links, being instances of failure modes, provide the samples required by reliability analysis software tools and methods. LRCM software and related procedures facilitate the growth of knowledge, manage the work order-to-RCM relationship, and generate samples for subsequent reliability analysis.

May 1, 2011

Promoters for Soap Flotation of Phosphate Minerals

Sep 13, 2010

By Gregg A. Scott, Gordon F. Revey

"The Folsom Dam is a 340-foot-high concrete gravity dam with embankment wing dams located on the American River about 20 miles northeast of Sacramento, California. Folsom Dam is operated andmaintained by the U. S. Bureau of Reclamation (Reclamation). As part of the Central Valley Project,Folsom Dam is a multipurpose facility providing water supply storage, flood control, power generation, and recreational opportunities."

Jan 1, 1999

By A. Bascetin

Waste materials caused by mining activities are an important environmental problem. Paste technology is a good alternative for waste management because it has many benefits in the aspects of environment, cost and safety. Disposal of process wastes in paste form is an attractive option for waste management, as it eliminates or reduces the risks associated with conventional methods. Due to the geotechnical characteristics of the paste, it is very similar to soil materials. So determining the geotechnical properties of the paste material is essential to durability of the paste. The some important geotechnical properties are compressive strength, porosity, shear strength, hydraulic conductivity, water content, consolidation, etc. In this study, the important parameters and the relation between them were investigated and obtained some results which will affect for optimum design of waste management.

Jan 1, 2012