Search Documents

By Scott Webster

Dynamic pile Monitoring Services (DMS) have been used for testing of offshore piles for several decades. However, most of this testing was to measure hammer performance and pile stresses rather than pile capacity or soil resistance. As the need for more economical solutions for foundation support increases, the use of DMS has provided a better means of evaluating in-place pile capacity for offshore structures, and therefore a method of determining pile acceptance. The authors have been involved in several offshore projects where DMS has been the primary source of data for acceptance of the driven pile foundations. The use of DMS for evaluation of offshore foundations requires considerations quite different from land applications and these considerations are often necessary for the careful and thorough analysis of the collected data in nearly real time for determination of pile acceptance. Case Method capacity estimates are often of little use due to the non-uniform cross sections of the foundation piles and their deep penetrations. Therefore, capacity assessments should be made using CAPWAP which is a signal matching program whose utility and reliability has been proven on thousands of projects every year, both on land and offshore. Depending upon the soil conditions at a given location, capacity assessment after soil setup effects may be necessary. In addition, tension capacity is often critical when pile refusal occurs significantly before the design pile penetration depth. Evaluation of uplift capacity can be accomplished by a CAPWAP analysis, which results in a total capacity prediction and its shaft resistance component. The use of hydraulic hammers for driving of these piles also adds the requirement of controlling hammer energy such that over-stressing of the pile is avoided. The calculation of non-axial stresses such as bending or eccentric stresses may also be involved in order to prevent pile damage.

Jan 1, 2010

By W. W. de Graaf, M. J. Ntsekhe

Klipspruit Colliery is experiencing coal losses, which leads to a negative impact on coal production and subsequently loss in revenue. This study aimed to identify the possible causes of coal losses in the No. 4 upper and lower seams. The objectives were to identify potential sources of coal losses through a literature survey, to identify areas where the coal losses occurred, to determine factors affecting coal losses, and to identify the most cost-effective methods to reduce coal losses. Highwall losses, top-of-coal losses, and coal edge losses were identified as the major areas of coal loss at Klipspruit. These losses were mostly attributed to the drilling and blasting practises of the pre-split, interburden waste, and the coal seams. Recommendations include re-visiting the current pre-split design and the tolerances adopted for the interburden and coal seam drilling and blasting design. It is furthermore recommended that Klipspruit implement a continuous improvement plan for the drilling and blasting and refresher training for the blasting crew and operators.

Jun 10, 2024

By Martina Cadorin

Activated nanoporous biocarbon (aNBC) was prepared using E. grandis wood as a precursor material. Oxidated activated nanoporous biocarbon (ox-aNBC) sample was obtained from the aNBC by oxidation with nitric acid. The samples were tested as Pt nanoparticles catalysts support for ethanol oxidation reaction and as electrode materials for supercapacitors. The porous structure, chemical properties, and the structural and morphological characteristic of the materials were correlated with their electrochemical behaviour. Biocarbon materials showed similar high specific surface area. The oxidation treatment increases the content of the oxygenated and nitrogenated surface functional groups but without appreciably change in the nanostructure characteristic. The aNBC supported Pt nanocatalyst has better electrocatalytic performance for EOR. Oxygenated functional groups have a marked effect on the supercapacitors electrode behaviour, increasing the total electrical capacitance by pseudocapacitive contribution, but with a negative effect on the cell electrical resistance and cell response time.

Oct 30, 2017

By Galymzhan Karamyrzayev, Rashid Nadirov

Zinc ferrite ( ZnFe2O4) is a by-product of non-ferrous metal production and is considered a promising source of raw zinc. The most efficient way to extract zinc from its ferrite is via acidic extraction, specifically leaching by hydrochloric acid. A comparative study of synthetic zinc ferrite hydrochloric acid leaching in isopropanol, aqueous, and the mixed solvent was performed. Zinc ferrite was obtained by sintering a zinc and iron (III) oxide mixture. Crushed samples were subjected to leaching in 1 M HCl at 323, 333, and 353 K and pulp density of 1 g/100 mL. The dissolution of zinc and iron into solution in organic media reached 77% at 353 K, while in an aqueous environment this value was 65%. The activation energy of 70.0 kJ/ mol was found for the leaching process in an isopropanol environment, which is lower than that in an aqueous solution by 15%. The more efficient leaching effect of isopropanol is attributed to the lower dielectric constant of the alcohol which increases the affinity of chloride anions for zinc and iron cations at leaching.

Jun 5, 2022

By D. W. Butner

The blast -hole method for drilling and breaking ground is not new to the mining industry . For several years it has been used rather extensively in Canada , particularly in the gold mines , where it was first developed and where the major advances in the technique as applied to present - day mining problems have been made . At present , 40 mines in Canada and the United States are using the method in one form or another , and from all indications its use will increase in the future . In two California mines , blast -hole diamond drilling is now used for a part of or for all stoping operations , and in one of these it is used to some extent in development work . At the Mountain Copper Co.'s Hornet mine in Shasta County, about 50 percent of the pyritic sulfide ore produced is mined by the blast - hole method , and the U. S. Vanadium Corp. mines 80 percent of the ore produced at its Pine Creek tungsten mine in Inyo County by this method . At Pine Creek , long -hole drilling and blasting is used for mining pillars also , and in pre - stoping development . The blast -hole diamond - drilling method is not applicable to all types of ore bodies . A third property in California , the El Dorado Limestone Company , El Dorado County, tried the method for several months in 1943 and 1944 , but , owing to certain factors that greatly increased mining cost , the company soon returned to conventional mining methods .

Feb 1, 1948

By Gustavo Henrique Bolognesi Donato

Ensaios de curva R (J vs. ?a – crescimento dúctil de defeitos) e de propagação de trincas por fadiga (da/dN vs. ?K) são balizados por normas como a ASTM E1820, ISO 12135 e E647, as quais exigem dimensões mínimas para as amostras C(T) ou SE(B) a fim de garantir condições SSY e portanto a validade de K e J. Entretanto, tais exigências usualmente conduzem a dimensões expressivas que dificultam a retirada de amostras de chapas finas ou mesmo de muitas estruturas reais. Como alternativa, estudos de Koppenhoefer e Dodds (1998) e mais recentemente de Shin e Lin (2012) indicaram a possibilidade de uso de amostras em miniatura (inclusive Charpy contendo pré-trinca) para determinação de curvas R e da/dN vs. ?K. As grandes questões são a viabilidade de ensaio de amostras pequenas com repetibilidade e a adequada avaliação dos limites de validade das forças motrizes nestas geometrias, a fim de garantir condições de similitude. Como um passo nesta direção, este trabalho investiga o potencial de amostras Charpy pré-trincadas (10x10x70mm) na determinação de curvas R e da/dN vs. ?K. Inicialmente, ensaios de ambos os tipos foram realizados em amostras de um aço estrutural ferrítico empregando uma máquina universal MTS 810. Apesar das dimensões reduzidas dos espécimes, os ensaios se mostraram viáveis e apresentaram boa repetibilidade e estabilidade dos resultados experimentais. Ainda, boas práticas de ensaio puderam ser estabelecidas para suportar os trabalhos futuros com tais geometrias.

Aug 8, 2018

By Arif Emre Dursun, Ali Aras, Hakan Özşen

Specific energy (SE) is defined as the amount of work required to cut a unit volume of rock and is used to estimate the performance of excavation machines. Generally, the SE value is produced from full-scale or small-scale rock cutting tests. However, these tests require expensive equipment and experienced personnel, and the testing procedure is time consuming and impractical. Therefore, for estimation of SE, this study aimed to find a solution to estimate SE using rock mechanics test results and Bond work index values (BWi), which can be produced in a more practical, less time-consuming manner and with inexpensive test equipment. Small-scale rock cutting, rock mechanics and Bond work index tests were carried out on seven rock samples, which can be grouped into two different type of rocks: marble and travertine. In addition, the instantaneous cutting rates (ICR) of a selected roadheader were calculated using SE values. Rock mechanics tests performed in this study were uniaxial compressive strength (UCS), Brazilian tensile strength (BTS), ultrasonic velocity (Vp), Schmidt rebound hardness (RL), corrected point load index (Is(50)) and density (ρ). The simple regression method was used to estimate SE from rock properties and BWi. As a result of this simple regression, a significant and highest correlation was found between SE vs. UCS and Is(50). A good correlation was found between SE vs. BTS, RL and BWi values. A moderate correlation was found between SE vs. Vp and ρ.

Jul 28, 2021

By Albert J. Phillips

The effect of impurities on the flowsheet in the smelting and refining circuits for copper, lead and zinc is reviewed and the interflow of by-poduct metals from copper, lead and zinc plants is pointed out. The principal points of separation of all impurities in the circuits are indicated and the additional steps added to these circuits in order to effect impurity separation me shown. In this day and age, when difficult metallurgy is mentioned, one thinks of the extraction of more refractory or possibly the alkaline earth or rare-earth metals. It is true that the extraction of metals having a high affinity for oxygen and deleterious solubility for that element in the liquid metal, affords some of the most difficult extractive metallurgy problems. When this is coupled with an affinity for hydrogen, nitrogen, and carbon a devious approach is required that sometimes rivals the complexity of the metallurgy with which this paper deals. However, in all such cases the aim is for a simple

Jan 1, 1962

By Filipe Sathler

Mediante efeitos de sazonalidades do mercado Siderúrgico, períodos de crise, aliados às necessidades de reparos de equipamentos, os Altos Fornos são, eventualmente, submetidos ao desligamento. O procedimento específico mais utilizado é o Blowdown, com o abaixamento de carga até nível de ventaneiras, facilitando posterior limpeza e reparo. Para sucesso deste procedimento, é essencial um planejamento adequado das atividades. Informações técnicas e experiências operacionais permitiram o embasamento teórico e a execução do Blowdown do Alto Forno 03 da ArcelorMittal FCSA (Tubarão). Como preparação, foi efetuado o aumento do fluxo periférico (remoção de cascão) e o aumento da permeabilidade do Cadinho (maior circulação de líquidos, limpeza e drenagem). Realizou-se também a preparação de equipamentos específicos e controle dos parâmetros operacionais. O abaixamento de carga foi devidamente realizado conforme planejado, até o nível de ventaneiras e permitindo paredes internas livres de cascões.

Aug 16, 2017

By J. L. Hoover, P. W. Conrad, J. Downey, S. Parrow, S. Rosenthal

The goal of the drill bit consumption study was to develop an equation(s) based on various components that affect drill bit wear and use that equation(s) to estimate the consumption of bits during production drilling. Drill bit data from various geographic locations were compiled and used to develop linear regression equations using the Microsoft Excel software package. Multiple drill bit consumption equations were developed and statistical analysis was used to verify the accuracy of those equations. The equations will allow mining companies to more accurately forecast drill bit consumption when evaluating new mine properties. This capability becomes increasingly beneficial to forecasting as the cost of consumables increases.

Jan 1, 2012

By T. Thuy Minh Nguyen, Sathish K. Lageshetty, Paul Bernazzani

The addition of nanoparticles to epoxy resins often results in changes in the physical properties of the material particularly when dealing with thin coatings. By characterizing the mechanism of interactions between nanoparticles and polymer chains the material could be tailored for specific applications or properties such as enhanced biodegradability. This study compared the characteristics of common DGEBA resin coated on a silicon substrate and embedded with nanoparticles of TiO2 and Fe2O3. Specifically, we investigated the rate of curing, and the thermal stability of these nanocomposites. Results show changes in the stability for compounds containing TiO2, while Fe2O3 significantly enhanced the curing rates of the nanocomposites while maintaining similar physical properties.

Mar 1, 2017

By Manis Kumar Jha, D. D. Pathak, Archana Kumari

Treatment of secondary/waste to recover rare earth metals (REMs) is gaining importance due to its increasing global demand, lack of availability of high grade natural resources and huge generation of secondaries. Present paper reports the critical review on available processes for recovery of REMs from secondaries viz. manufacturing scraps, e-waste, industrial residues such as red mud, fly ash, waste water, etc. Hydrometallurgical processes with combination of Beneficiation/ Pyro-/Electro techniques are discussed to recover REMs effectively. The recommended processes require less energy to deliver high purity yield which is one step towards green environment. Salient findings on various methods are reported with recommendations which will be helpful to researchers working in the area of REMs extraction.

Mar 1, 2018

By William E. Dennis

"At the request of Philip S. Hoyt, the Eagle Mountain fluorspar deposits in section 35, block 68, Texas & Pacific Railroad Survey No. 9, were examined by an engineer3/ of the Bureau of Mines during March 1943: As a result of this examination; a preliminary program of trenching, sampling and core drilling by the Bureau of Mines was begun in. June 1943.4/ Eight deposits were explored.The Federal Geological Survey mapped the properties and furnished geologic information throughout the program, while the Texas .Bureau of Economic Geology6/ made preliminary maps that facilitated planning the exploratory work on section 35.The eight deposits explored by the Bureau of Mines are in block 68, Texas & Pacific Railroad Survey No. 9, Hudspeth County, Tex., approximately 7-1/2 miles south of. Hot Wells and 12-1/2 miles south of Allamoore, which is 10 miles west of Van Horn and 20 miles east of Gierra Blanco on U. S. Highway 80(fig. 1). A graded gravel road, built by the Public Roads Administration, leads from Hot Wells to the deposits in section 35, and there are unimproved roads, passable,by automobile, to all the other deposits.Carload shipments can be made to and from Hot Wells on the Southern Pacific Railroad, and complete railroad facilities are available at Allamoore on the Texas & Pacific Railroad.Van Horn and Sierra Blanca are the only local source of labor and. supplies. The prevailing wage for common labor is 60 cents an hour. Living accommodations are obtainable in Horn and Sierra Blanca.No electric power lines pass near the deposits. Diesel and gasoline motors are employed to furnish power for mining and milling operations.Two recently 'drilled water wells on section 35 furnish water for the mill. Other wells will be drilled if the present supply is inadequate for prolonged Peak operation.The properties lie in the foothills on the northeast side of the Eagle Mountains at 5,500 feet altitude. The Eagle Mountain Range rises sharply from a broad, flat valley known as Eagle Flat. Eagle Peak, the highest in the range, has an altitude of 7,510 feet. In the vicinity of the fluorspar deposits the topography is moderately reliefs ranging from 50 to 300 feet."

Jun 1, 1946

By J. Fu

"Since it was first identified in 1817, selenium has received considerable interest. Native selenium and a few selenium minerals were discovered several decades later. With the increasing number of selenium minerals, the occurrence of selenium minerals became the focus of much research. A great number of selenium deposits were reported all over the world, although few independent selenium deposits were discovered. Selenium is obtained mainly as a byproduct of other metals, and is produced primarily from the anode mud of copper refineries. This paper presents a comprehensive review of selenium minerals, as well as the treatment of copper refinery anode slimes for the recovery of selenium. Our focus is on the selenium minerals, including their discovery and occurrence, and the distribution of selenium resources. In addition, the main methods of recovering selenium from copper anode slimes are summarized. IntroductionSelenium (Se) was first observed in 1817 in a laboratory (Greenwood et al., 1984). The discovery of selenium was made by the Swedish chemist J.J. Berzelius and J.G. Gahn, who isolated selenium from a red residue in sulphuric acid from pyrite mined at Fahlun, Sweden. Selenium was named from the Greek word selene (moon), since it resembled tellurium, which had been discovered a few years earlier and named from the Latin word tellus (Earth).After the first observation of selenium in the laboratory, selenium received considerable interest. In 1954, E.P. Kaiser pointed out that Se is enriched in sulphide ores and often associated with Bi, Co, Sn etc. (Kaiser 1954). In 1959, Hawley and Nichol investigated selenium in Canadian sulphide minerals, and presented the content of selenium in sulphide from several deposits of different types. They also proposed that Se is enriched in lowtemperature hydrothermal pyrite (Hawley and Nichol, 1959). The thermodynamic conditions for forming native selenium and selenium minerals in sedimentary rocks were discussed, as well as geochemical behaviour of selenium near the oxidation zones of sulphides in the 1970s (Howard III, 1977; Zhu et al., 2003). Zhu et al. examined the morphology, features, and genesis of native selenium from Yutangba, Enshi City, Hubei Province, China in 2004, and pointed out, from the different forms of native Se, that selenium can be activated,transformed, remobilized, and enriched at sites such as in the unsaturated subsurface zone or in the saturated zone (Zhu et al., 2005). The transport and deposition of selenium in felsic volcanic-hosted massive sulphide deposits of the Yukon Territory, Canada was studied and reported by Layton- Matthews et al. (2005)."

Jan 1, 2016

By M. J. Voigt, R. A. Govender, A. Mainza, L. Bbosa

"Mineral texture is a critical factor which controls ore variability and is an important attribute in geometallurgy. In relation to downstream processes, it affects the fracture pattern during breakage, where rock strength is inherently a function of mineral texture. Because of the subjective nature of mineral texture, it has not been easy to quantify, especially in the context of a measurement suitable for use in geometallurgical programmes. The aim of this paper is to present the first steps in developing a 3D mineral texture quantification method for drill core and to assess its sensitivity to differences in rock strength using a case study. The methodology includes classifying the textural information using the 3D grey level co-occurrence matrices (GLCM) and X-ray computed tomography (XCT) coupled method. Rock strength tests were performed using the split Hopkinson pressure bar (SHPB). The case study investigates a heterogeneous polymetallic sulphide deposit and a homogeneous shale subdivided into three ’mineral textural types’. The variability is largely captured by the GLCM matrices, and preliminary trends can be observed where the shale is finer grained and has a higher yield strength in comparison with the coarser grained polymetallic sulphide ore. IntroductionModern mining requires the exploitation of lower grade and more complex, heterogeneous orebodies to address the growing industry demands. Historically, processing plants were designed and built based on average ore characteristics and therefore are relatively inflexible when facing the full spectrum of ore variability in heterogeneous orebodies (Lamberg, 2011; Lotter, 2011; Schouwstra et al., 2013). The practice of geometallurgy represents an opportunity to manage ore variability in the mining industry (Powell 2013; Baum, 2014; Yildirim et al., 2014; Nguyen, 2013). It focuses on quantifying the relationships between ore characteristics and their downstream mining and processing responses, often starting with small-scale laboratory testing. The purpose of geometallurgy is linked to maximizing the net present value (NPV) of an orebody by minimizing technical and operational risk – where ‘ore variability’ is considered one of the most significant technical risks."

Apr 1, 2019

Can mining promote sustainable development? What is sustainable development? Is sustainable development good for corporate sustainability? Does it work in practice? If so, is it good for business? This paper does not seek to provide definitive answers to these issues. Rather, it is presented in the interests of sharing information and contributing to the pool of collective experience. The discussion will draw on the experience of Placer Dome in Papua New Guinea (PNG). Sustainable development means development that is maintained at a steady level without exhausting natural resources or causing ecological disturbance. The term æsustainable developmentÆ is often linked to the concept of ecological equilibrium, development that is self-replenishing. While its essential meaning remains the same, in practice, and for todayÆs complex and industrial world, different people will interpret sustainable development in different ways. Given the dynamics of development and the competing social, political and economic interests, sustainable development must be seen from a much broader perspective. This is the point that this paper will attempt to make. Mining, an activity that uses non-renewable resources, can promote sustainable development. The 1987 Brundtland Report (also known as the Report of the World Commission on Environment and Development), defines sustainable development in a broader manner - as development that meets the needs of the present world without compromising the ability of future generations to meet their own needs (Elkington, 1997). This definition calls for inter-generational equity in the development and use of resources by many organisations, including multinational corporations. Corporate sustainability, on the other hand, is about developing strategies that guide a corporation to stay alive and, more importantly, to stay ahead of its competitors. It is basically about survival in a competitive social and commercial environment. In a corporate world, profitability is survival. In this context, corporate profitability, the main ingredient of corporate sustainability, is important for sustainable development. Without profits, corporations will find it difficult to practice sustainable development or indeed any development. Sustainable development can integrate mining activities with the rest of the community, add value and, in the long-term, profits to the bottom-line. Ultimately, sustainability will force corporations to adopt strategies based on a longer time scale to survive. In the mining sector, corporate sustainability depends on a close relationship with all stakeholders, particularly landowners for whom sustainable development is critically important. Increasingly, there is an acceptance of the view that success is not achieved simply through competition in price, cost and technology but, more importantly, through creating social infrastructure which support community ethics, norms and values essential for trust and partnership. Needless to say, mining companies that engage in appropriate community-based development in support of inter-generational justice recognise the true value of sustainability. This is sometimes called the æhuman sustainability approachÆ which underlines the critical significance of trust in relationships with stakeholders and continuous improvement of corporate capabilities directed towards the future (Dunphy and Griffiths, 1998). In the long-term, such development will enhance corporate public image and acceptability. In practice, both concepts can be built on the principles of economic viability, environmental quality and social justice -what, in todayÆs parlance, is increasingly becoming known as the ætriple-bottom-lineÆ approach to business (Elkington, 1997). Underpinning this approach is a process of continuing dialogue and co-operation between governments, non-government organisations (NGOs) and business.

Jan 1, 1999

By N. L. Wimmler

"INTRODUCTION The Southern Cross district in Deer Lodge County, Mont., has been chiefly a gold producer. Most of the production has come from gold-bearing hematite-limonite ores. Some of these ores were mined and shipped to smelters for use as flux in smelting copper ores. A magnetite deposit in the Pomeroy property, containing no gold or other economic nonferrous minerals, was mined from 1921 to 1923, the ore being shipped to smelters for flux.The iron-bearing deposits in the Southern Cross area were examined by Bureau of Nines engineers/ on June 28, 1943, and October 14, 1943. As a result, a Bureau exploration project was recommended; it was conducted during 1944. A magnetometer survey was first made of the magnetite-bearing area at and in the vicinity of the Pomeroy property. Exploration by diamond core drilling was then conducted within this area, and in the Southern Cross and Hold Fast properties. The cyanide tailings dump at the Hold Fast mill was sampled by auger drilling.This report presents the data obtained by the Bureau of Mines exploration."

Dec 1, 1946

By Y. J. Wang

The selection of a shaft size for ventilation purposes is a classic problem of concern to mining engineers. This presentation is concerned with the sizing of conventionally-sunk circular shafts with concrete or shotcrete linings. Costs of sinking shafts of three different depths (from 500 feet to 1000 feet) and six different diameters (from 14 feet to 24 feet) were obtained through questionnaires to shaft contractors. The primary objective of the economic model presented is the balancing of detailed annual capital and operating costs to achieve the minimum overall cost of the shaft installation over its life. The economic model is similar to previous analyses but treats several of the individual cost categories in an updated fashion. Included in the paper is a detailed analysis of the effects of varying power costs on optimal shaft size. Also included are a statistical analysis of current shaft costs and comments on the choice between shotcrete and concrete linings.

Jan 1, 1977

By Francis Perron

The Directive 019 on mineral industry, which was officially adopted in 1989, is the main tool used by the Quebec Ministry of Environment for the environmental evaluation and control of mineral exploitation projects presented for approval. This document contain the environmental guidelines which must be met by all the mineral companies during and after exploitation. The Directive 019 also contain all the information required by the Quebec Ministry of Environment in order to fully analyse the environmental impacts caused by the mineral projects proposed to the Ministry for approval. The proposed modifications of the Directive 019 cover many new topics that were not addressed in prior editions, these include : water recirculation, groundwater protection, tailings management and post exploitation environmental controls.

Nov 1, 2002

Surfaces forces have been measured between gold sphere and gold-coated glass plate in xanthate solutions using an atomic force microscope (AFM). The measurements conducted in potassium amyl xanthate (PAX) and potassium ethyl xanthate (KEX) solutions showed long-range hydrophobic forces, with the force curves showing no evidence for nanonubbles on the surface. The strongest hydrophobic force was measured at contact angle of 94° with a decay length of 23 nm. The hydrophobic force became weaker at higher concentrations and after a long immersion time, which may be attributed to the xanthate species adsorbed on top of the first mono layer. The hydrophobic force became stronger when the residual xanthate solution is displaced by pure water, indicating that hydrophobic force becomes the strongest in pure water.

Jan 1, 2009