Search Documents

By J. G. Groppo

A series of performance studies have been conducted using counter-current column flotation to recover a marketable clean coal product from existing preparation plant fine waste streams. The test work was conducted at several preparation plant sites in Kentucky and Virginia and utilized a 0.15m (6 in.) I.D. column that was 5.79m (19 ft.) high. The refuse streams tested included both thickener feed and classifying cyclone overflow with a typical size distribution of 100 mesh X O. The percent solids of the column flotation feed varied from 1.5 to 15% while the ash content ranged from 30-60%. The concentrates produced contained 2-10% ash with BTU recoveries of nearly 90% using 0.12-1.25 kg/ton (0.25-2.5 lbs/ton) fuel oil and 0.12 kg/ton (0.25 lb/ton) MIBC. These results were consistent with or better than results obtained in preliminary laboratory scale column flotation evaluation. Test results from 7 different seams are discussed as well as scale-up relationships utilized to design a full scale installation presently in operation.

Jan 1, 1990

[A Aall, Christian H., M49 B VP, Dir of Smelt & Refin, Am. Metal Climax Inc., 1270 Ave. of the Americas, N.Y. Aaroe, Stanley L., A54 B VP, The W. S. Tyler Co. of Can. Ltd., St. Catharines, Ontario, Canada Abalos, Toodulo Q., J57 A Prod Foreman, Lepanto Cons. Mng. Co., Mt. Province, Philippines Abbass, G., M55 P. O. Box 680, Hong Kong, China Abbitt, James M., A54 770 Sole Blvd., Bartow, Fla. Abbott, Raymond C., J59 3442 Greenwich Ave., Columbus 24, Ohio Abdullah, N. Y., J53 Dept. of Mines, Res. Div., P. O. Box 1016, Tiger Lane, Ipoh Perak, Malaya Abel, John F., Jr., J53- 100 Maple, Littleton, Colo. Abell, Leo M., M31 B Conc Supt, Phelps Dodge Corp., Morenci, Ariz. Abendroth, Harry E., A57 A Geol, Union Carbide India, 183 Brabourne Rd.. Calcutta. India]

Jan 1, 1961

By W. S. Ayres

A BRIEF history of the growth of the anthracite-coal preparation will give a better view-point from which to judge the present problem of separating slate from coal. At the beginning of the commercial value of anthracite, 70 years ago, only the pure portions, or " splits," of the veins were mined and shipped to market, and without any preparation or screening other than the selection, while loading, of the glassy lumps, and the rejection of the fine material and the slate that had strayed accidentally into the coal. The next step was the crushing or breaking of the coal (hence the name Lt breaker" as applied to the preparation-building), and the sizing of it by means of bars or revolving screens. This stage of its development marked the advent of the "breaker-boy " as a slate-¬picker, with his ever-increasing capriciousness. As the richer veins or ? splits " became exhausted and the market demanded a still greater output, the less-pure " splits " and the thinner veins were utilized to produce the coal. Carrying as they do a far greater percentage of impurities; particularly when removing the pillars, it became necessary to build new and better equipped preparation-plants. Finally, we are now at the highest stage of complication yet known to the art of coal-preparation. We are dealing with varying specific gravities, frictional difference, hardness, structure, and form in the pieces of coal and slate coming from many different veins, and

Dec 1, 1909

By James P. Sloss

MOST students that plan to enter the mining profession attempt to obtain some kind of practical experience before graduation. Six or seven years ago it was an easy matter for undergraduates to find employment during the summer vacation and return to school in the fall filled with enthusiasm to dig deeper into the theoretical field. However, during the past few years it has become extremely difficult for an inexperienced undergraduate to obtain even a menial job in mining. This was the situation which presented itself to the author and his partner, T. M. Patten several months before school closed in May, 1934. At that time, Mr. Patten's training consisted of two years study in Mining, and mine included three years' study in Mining Geology at the Missouri School of Mines and Metallurgy. With this technical training and no practical experience, we conceived the idea that custom assaying in some of the western mining districts should be a lucrative business. We thought that the renewed interest in prospecting for gold and the opening of new mines should provide more assay work, and believed that we might secure it if we were on the spot where the assaying was needed. We realized that it would be out of the question for us to obtain the necessary equipment with which to establish an assay office. Even if such an office were established we had a maximum of but three months during which to operate. So we determined to build some kind of inexpensive equipment that could be placed in an automobile, or trailer, and be moved from one camp to another. We then began to study the theoretical aspects of assaying and started experimental work with the equipment that we proposed to build.

Jan 1, 1935

By C. Vipulanandan

Installation procedure and the quality of the material used in the construction have significant effects on the behavior of the Auger Cast in Place (ACIP) piles. In this study, Installation and curing of a 760 mm (30 in.) diameter and 12 m (39 ft) long ACIP pile with a design capacity of 1140 kN (128 tons) in hard clay was investigated. Construction quality was monitored using the automated monitoring system where the volume of grout pumped and the pressures were monitored with depth. The curing of the pile was monitored using axial vibrating wire strain gages at four levels and lateral vibrating wire strain gages at two levels. The residual strain and temperature profile in the curing pile was monitored over a period of week to determine the appropriate time for load testing the pile. Axial behavior of Auger Cast in Place (ACIP) Piles in hard clay was studied using full scale load test on an instrumented pile. The load-settlement and load transfer relationships of the pile was investigated based on the load test results. Development of skin friction in the load test pile and the reaction pile was also investigated.

By Alessandra Savazzini dos Reis

A indústria de cerâmica vermelha brasileira consome 10,3 bilhões de toneladas de argila ao mês para produção de telhas e blocos. Uma alternativa para tornar o setor mais sustentável ambientalmente é a incorporação de resíduos na massa argilosa. Na própria olaria são gerados resíduos, tal como, o resíduo de massa cerâmica crua originado na etapa de conformação das peças. Este trabalho visa caracterizar o resíduo de massa cerâmica crua para incorporação na massa argilosa usada em cerâmica vermelha. O resíduo de massa cerâmica crua foi caracterizado através de ensaios de FRX, DRX, calorimetria exploratória diferencial e termogravimetria, limites de Atterberg e distribuição de tamanho de partículas. Corpos de prova foram conformados, secos à 110ºC e queimados à 900ºC em forno industrial e foram submetidos a ensaios de absorção de água, porosidade aparente, massa específica aparente e resistência à flexão. Os resultados evidenciam que as propriedades cerâmicas avaliadas nos corpos de prova atendem aos valores das argilas-padrão brasileiras para uso em cerâmica vermelha.

Aug 16, 2017

By Eduardo Macedo Junior

O presente trabalho descreve o desenvolvimento de uma nova especificação para a Linha de zincagem numero 3 (LZC#3) da Companhia siderúrgica nacional (CSN), de grande demanda e aceitação, alta produtividade e foco nos requisitos do cliente que tangem qualidade superficial e características metalúrgicas (resistência mecânica) em aços para atendimento do mercado Norte-americano. Este novo produto tem como característica o ciclo de recozimento com velocidade alta para obtenção de microestrutura 100% encruada na saída do equipamento e limites de escoamento e resistência acima de 500 MPa. A combinação dessas características do produto junto com as características do processo tornou a especificação “ASTM-A653MSS80CL1” um grande desafio para garantir qualidade superficial sem comprometer as propriedades mecânicas especificadas assim como a integridade do equipamento. O baixo custo de produção associado a alta produtividade desse produto fazem da especificação “ASTM-A653M-SS80CL1” um produto de extrema importância para a estratégia adotada pela CSN, mantendo dessa maneira sua competitividade no mercado Norte-americano e garantindo capacidade máxima de produção do seu equipamento em tempos de retração do mercado interno.

Aug 17, 2017

[A Aall, Christian H., M49 D Mgr, American Metal Climax, Inc., 61 Broadway, New York 6, N.Y. Aaroe, S. L., A54 B Sales Mgr, The W. S. Tyler Co. of Can. Ltd., St. Catharines, Ont., Canada Abalos, Teodulo Q., J57 A Foreman, Lepanto Cons. Ming. Co., Mt. Province, Philippines Abbass, G., M55 P. O. Box 680, Hong Kong, China . Abbitt, James M., A54 770 Sole Blvd., Bartow, Fla. Abdullah, M. Y., J53 Dept. of Mines Res. Div., P. O. Box 1016, Tiger Lane, Ipoh Perak, Malaya Able, John F., Jr., J53 A Ming Engr, USA SIPRE 1215 Washington Ave., Wilmette, Ill. Abell, Leo M., M31 B Conct Supt, Phelps Dodge Corp., Morenci, Ariz. Abenius, Hakan Wilhelm, M52 A Mng Dir, Stora Kopparbergs Bergslags AB, Falun, Sweden Abenoroth, Harry F., A57 Natl. Carbon India Ltd., 18A Brabourne Rd., Box 217, Calcutta, India Abercrombie, Harry W., J56 1645 Camphor Dr., Lakeland, Fla.]

Jan 1, 1961

By Gordon T. Austin

The combined value of production of natural abrasives, which include tripoli, special silica stone, garnet, staurolite, and emery, decreased about 24% in 1992. The decrease in the value of tripoli production was the result of a decrease in total production. Emery decreased owing to a decrease in the volume of the material produced. Special silica stone experienced a significant increase in unit value and decrease in the quantity produced. Garnet showed a 6 % increase in quantity and a 36 % decrease in unit value. Staurolite decreased about 27 % in the quantity produced and value compared with those of 1991. The fused aluminum oxide industry showed a slight increase in the quantity produced and a 4 % increase in the value of production. The silicon carbide industry saw a 7 % increase in the quantity produced and a 10 % increase in the value of production. Combined, the industries increased 4 % in quantity and 6 % in value compared with those of 1991.

Jan 1, 1992

By C. A. Rowland

The rising costs for and the possibility for limited availability of electrical energy are emphasizing the continual conflict faced in the selection of comminution circuits used in preparing ores for concentration, namely; capital cost vs. operating cost. Frequently, the circuit with the lowest capital cost is not the most efficient in the use of electrical power and wear resistant materials. The simplest circuit in terms of flow, pieces of equipment and capital cost is the single stage autogenous or partial autogenous circuit used to grinding primary crusher discharge or run of mine ore to the desired product size. (Fig. 1) From this circuit, complexity increases to multi-stage crushing circuits preparing feed for multi-stage grinding circuits. Fig. 2 showing a three stage rod mill ball mill arrangement is an example of a complex grinding circuit. Stage concentration further complicates the flow. Multi-stage circuits being the most expensive to install, often give the greatest operating flexibility and offer the best possibilities for the most efficient use of available power and wear resistant materials. Within available grinding circuits, other comparisons such as high speed vs. low speed mills, grate discharge vs. overflow discharge, metal liners vs. rubber liners, high charge vs. low charge, etc. all add to the conflict

Jan 1, 1977

By Daniel Augusto Godinho de Carvalho

Since the beginning of BOF process, slag formation has been subjected to extensive development. During the initial stages of the blow, fast slag formation is primordial for the process performance. This is mainly to allow oxidizing reactions, and also to protect the refractory. A modeling of BOF process for the purpose of process optimization requires precise knowledge concerning the dissolution of CaO and MgO based materials. Using this knowledge, the optimal process conditions can be ensured by a controlling of the slag formation during the converter steelmaking process. Taking into account an application of large amount of different raw materials, as well as location-specific process conditions, the characterization of the dissolution behavior of different additives is an important key to improve the technological process. Thereby, in the frames of this project, an appropriate model for slag formation is established and compared to operational results for a 330t BOF, operating at ThyssenKrupp CSA, Santa Cruz, Brazil.

Aug 16, 2017

By A. Sokolov, E. Hasikova, V. Gostilo, V. Titov

Introducing online X-ray fluorescence (XRF) analyzers in the mining and processing industries can lower costs and improve the representativeness and speed of analysis. The applicability of the CON-XTM industrial conveyor XRF analyzer for continuous measurement of potassium content in process materials was demonstrated at various stages of potassium muriate (MOP) production. The CON-X analyzer produced reliable and accurate results for sylvinite ore (27–36% KCl), MOP cake after flotation (88–97% KCl), and NaCl residue (1.5–5% KCl). Tests of the analyzer at an MOP-producing plant showed a < 0.5% difference between online and laboratory results.

Jan 1, 2014

By Guilherme Liziero Ruggio da Silva

Uma marcha estável do alto-forno (AF) está ligada à consistência das propriedades químicas, físicas e metalúrgicas das suas matérias-primas (MP), especialmente, as do coque. As propriedades do coque são reflexos das propriedades dos carvões que lhe deram origem. Em termos de propriedades ligadas à natureza do carvão, a qualidade do coque é bastante influenciada pelo rank dos carvões, que compuseram sua mistura, ou seja, quantidades de macerais reativos e inertes, bem como suas propriedades coqueificantes, que é, exatamente, a habilidade inerente aos carvões aglutinantes de quando aquecido, amolecer, tornar-se plástico e solidificar em uma massa coerente. Neste contexto, o presente trabalho se propõe a evidenciar as mudanças no modelo de britagem de carvões da Gerdau Ouro Branco, bem como a operacionalização do padrão criado. Após a implantação, verificou-se a elevação de 1.8% em DI.

Aug 17, 2017

By Feng Wang, Guojing Shi, Yangyang Xie, Zizong Zhu, Qiang Wu

The coal chars from northwestern part of China are characterized with high reactivity and low strength after reaction. Four type of coke-making coals selected from northwestern part of China were studied by proximate analysis, ultimate analysis, vitrinite reflectance analysis, and FTIR with curve-fitting analysis to obtain information on their chemical composition and chemical structure. The results show that the studied coals have relatively high values of final contraction of coke residue index (x) and relatively low values of maximum thickness of plastic layer (y) and average vitrinite reflectance. Based on the curve-fitting analysis of FTIR spectra, the aliphatic carbon (Cal), the aromatic carbon (Car), and the molecular structural parameters such as CH2/CH3, fa, Hal/Har, and (R/C)u are determined. The results of curve-fitting analysis indicate that the studied coals are characterized by a large amount of oxygen-containing functional groups and aliphatic side chains.

Mar 1, 2018

By Jilai Xue, Shuming Huang, Zengie Wang

The corrosion behaviors of chrome corundum/magnesia in laterite nickel slag were investigated by static crucible method. The results show that the molten slag can penetrate into chrome corundum or magnesia which are used as lining materials in smelter furnace, and the corrosion can occur at the slag-refractory interface and the inner area of the refractories as well. Both the penetrated amount of slag and the penetration depth of Fe, Si increase with increasing FeO content (10–25 wt%) in slag. Such penetration in magnesia is stronger than that in chrome corundum under the same corrosion conditions, as more pores in magnesia may provide channels for slag penetration and corrosion product transportation. A damage of the refractory linings and short service life of smelter furnace may happen during metallurgical processing slag with high FeO content.

Mar 1, 2017

By K. Saberyan

A technique is described for the solvent extraction of zirconium. In this method, zirconium has been extracted quantitatively from 0.005 M sodium salicylate solution at pH 2.5 - 3 using 0.01 M triphenylphosphine oxide dissolved in toluene as an extractant. Zirconium has also been recovered quantitatively from 0.2 M potassium thiocyanate solution, but extractions in nitric and hydrochloric acids (as media) were negligible. The resulting extracted metal ion has been stripped with sulfuric acid (0.5 M) and determined with inductively coupled plasma atomic emission spectrometry. This method has been applied successfully to achieve 95% recovery of zirconium from zircon concentrate.

Jan 1, 2010

By G. G. Krishna Murthy

Several experiments were conducted to determine the rates of heat transfer coefficients of CaO-SiO2-A1203-FeO slags at temperatures in the range 1623-1823 K The experimental technique involved measuring heating rates of a solid specimen, sub¬merged in slag phase, using a temperature probe made of Pt\ 10%Rh-Pt. Effect of %FeO (3-10%), %FeS (0.1-0.68%), %P205 (0.2-3.0%), %MgO(5-6%), and %MnO (0.96-3.84%) present in the slag on overall heat transfer coefficient, U, of slags was investigated. Simple first order heat balance equation in combination with experimental plots rising temperature of solid specimen versus time were employed to determine the values of U. The values of U determined in the present investigation were present in the range of 70-260 cal/Ks.m2. The value of U increased with increasing the slag temperature. The values of U were not effected by increased amounts of sulfur in the slag phase. The increased concentrations of MgO, FeO, MnO, and P205 in the slag phase decreased the values of U. On the other hand, the increased amounts of Fe2O3 in the slag phase increased the value of U. Comparison of the results, obtained using the slag bath stirred by argon injection, with those determined without any stirring indicated that both radiative and conductive heat transfer mechanisms are important even at high temperatures.

Jan 1, 1993

By Ted C. Briggs

A special high-pressure Burnett-type compressibility apparatus was constructed and used to determine compressibility factors for pure helium, pure nitrogen, and nine helium-nitrogen mixtures containing 89.47, 79.04, 69.69, 60.09, 49.24, 41.02, 30.99, 20.53, and 10.67 mole-percent helium. A total of 161 runs were made consisting of 2,355 observed pressures. Data were obtained at 0°, 25°, and 50° C and at pressures to 1,000 atmospheres. A power series in the reciprocal volume, commonly called a Leiden series, is used to represent the compressibility factors. Three parameters in the series are required to represent helium, five parameters to represent nitrogen, and from three to five parameters to represent the mixtures. Compressibility factors are believed to be accurate to better than 0.1 percent over the entire pressure, temperature, and composition range.

Jan 1, 1972

By A. P. Page, G. E. Alexander, L. L. Sirois, A. A. Winer

A knowledge of the electrical surface characteristics of minerals is all-important in the choice of treatments to up-grade and beneficiate them. At their solid-liquid contacts, there are transfers of ionic species, which for insoluble oxide minerals are the H+ and OH-ions. The adsorption density of these ions can be detected by carrying out potentiometric titrations, and this paper describes the automation of such an apparatus. The details are discussed fully and the validity of the method is demonstrated by flotation tests.

Jan 1, 1969

By Ivo Dreiseitl

Bottom sediment sampling by means of a box corer, as a direct method of deep seabed exploration for polymetallic nodules, is the most comprehensive way to obtain various types of geological information on points forming a network of stations. However, direct information is lacking from areas separating those stations and has to be approximated by interpolation or extrapolation, which leads to uncertainties. Sediment sampling with a gravity or piston corer can provide information on the superficial, up to 4 m thick, part of the sedimentary cover. As opposed to box coring, gravity or piston coring provides no information on nodule abundance. Information for unsampled areas can be gained by application of remote techniques of exploration. The techniques of choice in visualising nodule-rich fields, nodule-free areas, hard rock outcrops and other obstacles for seafloor mining involve using sonar and continuous deep sea (CDS) camera. Seafloor mapping can be rendered with two major sonar types: the side scan sonar used to obtain seafloor imagery and multibeam sonar for bathymetric data; the two types are usually combined and work with an intermediate frequency profiler. Photo-profiling by means of a deep sea towed camera provides a series of seafloor photographs, each supplemented with information on the area covered by each frame, including the nodule abundance. Remote techniques have been quite frequently applied by the Interoceanmetal Joint Organization (IOM) in nodule field exploration. Recently, geoacoustic techniques (side scan sonar + profiler) and CDS were applied for exploration of IOM?s first prime area H11 (5372 km2) on 6 transects. During the IOM-2009 cruise, a total of 295 km of geoacoustic transects and 344 km of photo-transects were surveyed. The data obtained were processed with the aid of earlier information produced by multibeam sonar surveys. The aim of this paper is to demonstrate the advantages of remote techniques, particularly with regard to application of the towfish device, for geological and geotechnical applications in exploration for polymetallic nodules.

Sep 14, 2011