Search Documents

By Kot F. Unrug

Since the introduction of longwall systems, the prediction of roof behavior and support requirements have become the major issue referring directly to safety as well as productivity. In more recent times, and especially in the USA where longwalls are exclusively equipped with costly hydraulic self- propelled support systems, a decision whether a longwall is applicable in a given condition, and when so, what kind of equipment should be selected, is of primary importance. There are numerous examples where lack of experience, and subsequently wrong selection of supports or winning machines, resulted in considerable losses. It should be emphasized that careful studies of prevailing geological and mining conditions, especially in a new area, are required to assure a successful operation. An evaluation of the conditions can be carried out in different ways utilizing such methods as: - Theoretical approach. applicable when geological conditions comply with the theoretical assumptions. - Empirical relationship which gives satisfactory results where the coefficients could be adequately determined. - Structural geological studies which must be undertaken in all cases, since the frequency of fractures and their orientation have a prevailing influence on roof behavior. - Scale model study on equivalent material for determination of failure conditions in the roof and mechanism of movement (flow) of broken rock matter. Coefficients for empirical formulas can be determined by these types of studies, as can boundary limits for mathematical modeling. - Mathematical modeling, e.g., finite element analysis. - Measurements and observations taken underground during the development period end utilization of experience for previous longwall panels in the area. Usually it is the most practical method where mining and geological conditions are comparable. An application of me or more of the above approaches remains to be a matter of judgement for particular conditions, however, the utilization of a practical experience, when available, is usually the safest way for planning a successful longwall operation.

Jan 1, 1982

By d&apos, Kathleen J. Amico

THIS SUMMARY is identical to the summary given in volume III of this series of mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico and of the principal minerals imported into and exported from the United States. For further details on production see commodity and area chapters. A summary table comparing world and United States mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers [ ]

Jan 1, 1958

By Bhattacharyya A. K

A major constraint on sustaining high rates of production in the collieries of the Southern Coalfield of New South Wales is the inability to develop panels fast enough to match the rates of extraction. This inability is particularly crippling in the case of retreat longwall mining and is due to nearly half the time in roadway drivage being spent on strata control operations such as roof support.Increased rates of roadway drivage and significantly improved roadway stability can be achieved by the application of yield pillars between parallel roadways. These pillars are designed to yield immediately upon formation and transfer the damaging roof loads away from the immediate vicinity of the roadways. Since the width of the yield pillar is the key to their successful application, it was determined through the Yield Pillar Experiment conducted by Kembla Coal and Coke Pty Ltd at West Cliff Colliery.Three experimental headings, each nominally 5.5 m wide and 2.8 m high, were driven to form two tapering pillars. The width of these pillars progressively decreased from 24 m to 3 m over a length of 154 m. The convergence between the roof and floor of the headings measured at various cross-sections corresponding to predetermined widths of the pillars are analysed in this paper to evaluate the stability of the tapering pillars at the different widths.The width of the yield pillar in a three heading development layout at West Cliff Colliery was determined to be 7.5 m.

Jan 1, 1995

By J. J. Pye, J. B. Drew

The surface-diffusion coefficients of Ni63 diffusing on low-index planes of nickel single crystals have been measured over the temperature range from 400° to 1000°C using a precision autoradio-gvaphic technique. The activation energy for sur -face diffusion appears to he the same on the {111}, {110), and (100) planes and amounts to -0.60 ev. This is in good agreement with the value (-0.62 ev) reported for (111) planes obtained by mass-transport techniques. In an earlier paper, the authors have reported self surface-diffusion coefficients on silver.' In that work, a deviation of the diffusion coefficients from linearity in the Arrhenius plot was observed at high temperatures. This effect was attributed to a loss of tracer atoms into the bulk by volume diffusion. The purpose of the present work was to extend the technique developed to the nickel surface-diffusion system up to the point where volume diffusion would come into play. The nickel system especially lends itself to this technique due to the high efficiency of the isotope in darkening the film and the large absorption of the weak radiation (0.063 mev /3- particle of the trapped tracer atoms. The diffusion coefficients and ictivation energy for different orientations on nickel can also be compared with a report published by Blakely and Mykura 2 where a mass-transfer technique was used. This paper reports the self surface diffusion of nickel on the low-index planes over a wide temperature range using a precision autoradiographic technique. EXPERIMENTAL PROCEDURE The experiment is similar to that described in the earlier publication consisting of a radioactive needle as a source resting on a flat, smooth, chemically polished surface annealed in a dynamic dry-hydrogen atmosphere. The needle is held snugly on the surface by a holder fabricated from commercially pure nickel. The point source is made by grinding down a small-diameter nickel rod until a tip of approximately 0.1 mm radius is formed. It is then etched and the needle tip plated with the radioactive isotope Ni63. Nickel single crystals were used whose main impurities were spectrographically determined as Co 0.05, Fe 0.007, C 0.005, and S 0.003 pct. The surfaces, oriented to within 1/2 deg of the low-index planes, were carefully mechanically polished and etched in a 50-30-10-10 hot solution of acetic, nitric, sulfuric, and phosphoric acids giving a smooth polished surface. The crystals were then washed in distilled water and alcohol. Annealing temperatures ranged from 400° to 1000°C with a furnace arrangement in which the crystals could be brought up to temperature in times short compared to diffusing times. The temperature was maintained constant to ±10°C. In the temperature range investigated, the ratio of the surface-diffusion coefficient to the volume-diffusion coefficient (Ds/Du) was 105 or more and the mean bulk-penetration values, calculated from literature values of volume-diffusion coefficients,3 were on the order of 10-5 cm. After the diffusion anneal, the sintered needle is removed, and both the radius of the needle point and spot left on the crystal face are measured. The crystal is then placed on photographic film. Diffusion profiles are obtained by scanning the film with a recording microdensitometer which has a slit width of 10µ. DISCUSSION AND RESULTS The experimental conditions are such that the source strength and needle radius are essentially constant and the time is adjusted such that the mean bulk penetration is small. An exactly analogous heat-flow problem has been considered by Carslaw and Jaeger4 and the solution can be written in integral form as:

Jan 1, 1964

By Mroczek C. R, Evans D. A

Renison is a world-class ore deposit that has been mined for over 100 years. It currently has reserves of 5.06 Mt @ 1.88 per cent Sn and a projected mine life of 8.5 years. Recent advances in the geological understanding of the deposit have been associated with detailed structural and geophysical investigations accompanied with the discovery and exploitation of the Rendeep orebodies. Mineralisation is linked to the forceful emplacement of the Devonian Pine Hill Granite that resulted in a complex brittle (-ductile) deformation of the Eo-Cambrian host stratigraphy. Dilation jog development on the Federal-Bassett Fault in the Federal and Rendeep areas provided access for cassiterite-rich magmatic hydrothermal fluids responsible for carbonate replacement Mineralisation.

Jan 1, 1997

By X. -G. Chen, A. M. Nabawy

A novel manufacturing technique for Al-TiB2 nanocomposites has been developed, in which TiB2 nanoparticles were incorporated into liquid aluminum under mechanical stirring and in the presence of a K2ZrF6 flux-wetting agent. The microstructure of the Al-TiB2 nanocomposites was studied using scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The microhardness test was conducted to investigate the strengthening effect of TiB2 on the aluminum matrix. The TiB2 nanoparticles were successfully incorporated and dispersed into the aluminum melt in the presence of the K2ZrF6 flux during mechanical stirring. In the as-cast microstructure, most nanoparticles segregated in the interdendritic regions as a result of particle redistribution during solidification. The addition of 2, 5 and 10 wt% TiB2 nanoparticles increased the composite hardness by 60, 90 and 150% respectively when compared to commercial purity aluminum, indicating that the TiB2 nanoparticles imposed a significant strengthening effect on the aluminum matrix. The role of K2ZrF6 flux agent on the incorporation of nanoparticles into aluminum melt was discussed.

Jan 1, 2014

By T. V. Falkie, D. R. Mitchell

Many operational problems in mine haulage cannot be solved economically by conventional analytic or trial and error methods. However, a method of probabilistic simulation, which is based on the fundamental assumption that many of the variables governing any physical system are probabilistic, has been adapted to certain areas of operations research in coal mine haulage. This paper attempts to illustrate how simulation can be used in basic haulage research and what kind of results can be expected. Optimization in this case is performed in terms of locomotive and car movement, as well as best utilization of men and equipment, and is approached primarily from the standpoint of scheduling of the main haulage. Many operational problems in mine haulage cannot be solved economically by conventional analytic or trial-error methods. However, a method of probabilistic simulation, which is based on the fundamental assumption that many of the variables governing any physical system are probabilistic, has been adapted to certain areas of operations research in mine haulage. In many physical cases several probability distributions interact with each other in special ways, and it is not possible to solve for their combined effect in a mathematical equation. This is often true in the case of mine haulage, where such variables as number of empties or loads per trip, travel times, and number of cars or tons produced in a given time are probabilistic. By using a simple example of one secondary haulage segment of a large underground haulage system, this paper attempts to illustrate how simulation can be used in basic haulage research and what kind of results can be expected. Optimization in this case is performed in terms of locomotive and car movement, as well as best utilization of men and equipment. This is the type of preliminary research that will be needed as a first phase in any major haulage study, whether it be a relatively simple economic analysis or a plan for complete automation. The problem of optimization has been approached primarily from the standpoint of scheduling of the main haulage. It is evident that the method of proba-

Jan 1, 1963

By Miles M. J, Sandy D. A

It has long been known that drilling and blasting operations have a direct influence over productivity and costs of subsequent operations. If mine management is to effectively optimise blasting operations, good information is required on the operating costs of each of the affected operations, together with knowledge of how they are influenced by blasting. In practice it is not possible to do enough repeats of a full scale production blasting experiment to make a statistically significant analysis of the results. By monitoring each blast and subsequent operations in as much detail as possible, enough data will be available to effectively measure the effect of blasting on costs. This gives management an insight into the blast performance and is the first step towards optimisation. An Integrated Blast-related Cost Reporting System has been developed at the Rossing Mine Open Pit, which calculates the total mining cost for each blast. In assessing the total mining cost for each blast, use was made of an.integrated planning and management information system to collect relevant production variables, current operating costs and survey data. An automatic image analysis system was employed to measure the fragmentation of the blasted material in the back of haul trucks. A shovel monitoring system is also under development for use in assessing the muckpile diggability and, in conjunction with an appraisal of shovel component reliability, to estimate the maintenance cost under various digging conditions.

Jan 1, 1990

By Luis Orna

El trabajo que se ha desarrollado en Minera Yanacocha, conjuntamente con las áreas de Mantenimiento Mina y Operaciones Mina, es realizar una solución integral en línea y tiempo real de la programación de las actividades de mantenimiento preventivo y correctivo de los equipos pesados en el taller de mantenimiento. La idea con esta solución fue que los planeadores, programen los trabajos desde su inicio a finalización, de modo que se visualiza el avance en diferentes dispositivos (monitores, dispositivos móviles, etc). Los técnicos del taller de mantenimiento, como valor agregado pueden monitorear sus actividades, cerrar las órdenes de trabajo si es necesario, todos estos trabajos son realizados con información mediante interfaz a ERP.

Sep 1, 2017

By Nirmal Weerasekara, Lian X. Liu, The University of Queensland, Weiguo Xie, Benjamin Bonfils, Ping Yu

A mill model structure based on the population mass balance framework incorporating breakage characteristics, slurry and solids transport, product classification and discharge and energy consumption was reported in XXVII IMPC and named the Generic Tumbling Mill Model Structure Version I (GTMMS I). In this work, a new 4D (four dimensional) appearance function sub-model based on the experimental results of the JK Rotary Breakage Tester (JK RBT) was developed to describe the breakage characteristics and was applied to this new model structure. The newly developed 4D appearance function model has fewer fitting parameters and is more generic in nature. Most importantly, it is applicable to both high and low energy impact breakage. It is therefore much more versatile in comparison to the existing JKMRC t10- tn appearance function and the size-dependent JK M-p-q t10-tn appearance function. In addition, the Discrete Element Method (DEM) energy distribution model was integrated into the new model structure. With DEM results providing energy distribution information inside the mill directly, the selection function and the back-calculation method used in the existing JKSimMet modelling method are not needed in this model structure. With the above two revolutionary innovations, the previous model structure was upgraded to the Generic Tumbling Mill Model Structure Version II (GTMMS II). Furthermore, the new model structure is dynamic in nature with time-stepping technique for non-steady-state simulation. A case of the dynamic grinding of a SAG mill was studied to validate the GTMMS II. The model simulation results agreed well with the plant data. With the newly developed 4D appearance function model, the incorporation of DEM energy distribution and transport function, the GTMMS II is an important step forward towards mechanistic modelling of tumbling mills.

Jan 1, 2016

By Blight P

There is today widespread concern about the future of the mining industry. In attempting to understand the underlying causes the paper probes in some detail, the long term structural changes affecting growth of metal demand and the development of excess mineral supply capacity. This examination reveals an industry characterised by an unfavourable combination of high barriers to exit and low entry barriers. While rising entry barriers are expected to herald some improvement in the profitability of mining over the next decade, this adjustment is likely to be slow and will require a more economically rational assessment of the industry by corporations and governments Alike.

Jan 1, 1986

By D. Beregekoff, W. D. Forgeng

In the routine examinatlion of a wide variety of metal specimens it is sometimes necessary to have special methods of polishing in order to retain and reveal certain details in each specimen. Among such special cases is the retention of graphite in malleable and gray cast irons, the preservation of all types of non metallic inclusions in both hard and soft steels, obtaining a scratch-frec surface with soft metals, and avoiding the usual relief effects with very hard specimen. such as tool metals c3o1ltaining various carbide and nitride phases. It, is the purpose of this paper to give an account of some of these special polishing methods in use at the Union Carbide and Carbon Research Laboratories. The polishing procedures outlined have been found to give uniform results. It is obvious that only general rules and the most important working details can be given here. Following these rules, the polisher can obtain satisfactory results if he possesses the necessary patience and has a sincere desire to give as nearly perfect a finish as possible to his work. Procedure The specimen is flattened with considerablecare on a file or sharp cutting sanding belt, since the initial production of a flat surfacc greatly facilitatcs subscqucnt polishing. The polishing motors have two speed., 600 and 1200 r.p.111. ,It higher speeds specimens arc likely to he over-Ileated, therefore the high speed is used only when a saving of time is important. The following abrasive papers are used consecutively: Yo. 2, So. 1, No. 0, No. 00 and No. 000. The final wet polishing is done oil a cloth-covercd metal disk. Woolen broadcloth of the best quality and capable of resisting severe pressure is most commonly used on the last lap. . polishing felt of the type used for polishing optical glass has been found equally satisfactory and is much stronger than broadcloth. For retaining inclusions and graphite, a hard cloth with very little residence, such as

Jan 1, 1939

By Hunter GW

This paper gives an account of the filling system at Mount Isa from surface fill production to stope discharge underground. A brief explanation of the surface facility and reticulation is given prior to the discussion on aspects of underground reticulation. These include fill hole types, pipe and breastplate installation, wear characteristics, etc. The different types of fill and their respective applications is mentioned as a prelude to a general overview of the mining considerations associated with fill placement and its role in the long term planning strategy at Isa Mine. Some practical aspects of stope preparation and filling procedures are outlined for the various stoping methods. Finally a brief outline of future fill developments is given.

Jan 1, 1982

By Yates M. G, Rowlands A. T

Most geostatistical techniques applied to the estimation of ore reserves assume relatively unifonn grade and thickness within an ore deposit environment. In shear-hosted mineralisation this rarely occurs. The distribution of mineralisation is controlled by the kinematic and geometric variation within the shear zone. Although the kinematic variation is dependent primarily on the temperature (and consequently the depth) of formation of the deposit, the geometric variation appears to be relatively insensitive to this parameter. Shoot mineralisation is controlled either by the intersection of secoodary shear planes (brittle deformation) or the stretching lineation of the mylonitic fabric (ductile defonnation).Once the shear geometry is clearly identified, it is critical to review the distribution of grade and thickness of mineralisation. The practice of cutting high-grade intersections without reference to the shear model leads to underestimation of the amount of gold in the deposit. High-grade shoots may occur as pipe-shaped bodies within the system; their identification is essential for both resource estimation and mine planning purposes.

Jan 1, 1991

By Nathan Ferdinands

Outline Overview of Site and Partners ?MeanduMine ?Thiess?GroundProbe Technology ?Work Area Monitor (WAM) ?Software control ?Alarms MeanduMine King2East pit failures ?Background, and Northern Failure ?Southern Failure Recovery and conclusion

Nov 1, 2011

The paper will review the marked upsurge in the installation of new continuous metal coating lines, both hot dip and electrodeposition. Although some of this new capacity has been replacement for obsolete facilities or directed at traditional markets, eg building products, consumer durables etc, by far the major portion is targeted at the automotive industry. The reasons for the rapid growth of coated automobile panels are discussed. A comparison of the installed capacity with projections for this market indicate that a severe over-supply situation has arisen. Many coatings are now available for the automotive industry, each with their own strengths and weaknesses, but none as yet wholly satisfactory. Coating development has mainly been cost driven. This favours hot dipped coatings, providing surface quality and pressing problems can be overcome. The high cost per unit thickness of electrodeposited coatings has also seen pure zinc coatings being replaced by thinner, more corrosion resistant alloy coatings such as zinc-nickel and zinc-iron. Recently resin overlays have been introduced to improve the performance of electrodeposited coatings. Developments in coatings for the more traditional markets will be described. The fastest growing market in the last decade has been prepainted product for the building industry. This has led to the installation of extra painting capacity and again it appears an excess capacity situation has occurred. Over the same period the traditional zinc coatings have continued to lose market share to the zinc/aluminium alloy coatings, Galvalume and Galfan. These have been joined recently by '1'aiyo Crack-Free which has been taken up by some metal coaters. Galvalume is now widely accepted as being the best available coating for unpainted applications. It is also suggested that 'spin-off' coatings from automotive developments might find a niche in the consumer durable market. The end users of coated products, particularly the automotive industry, have demanded improvements in quality, such as surface smoothness, formability, etc. At the same time the new coating lines have to process wider strip and run at faster speeds. To reconcile these somewhat incompatible needs has required numerous process improvements, many of which need in-line instrumentation and computer control. The more important of these changes are discussed briefly. Finally the paper will describe the recent developments which have occurred in continuous galvanising in Australia and put them into context with the rest of the world.

Jan 1, 1993

Mine planning typically involves designing an operation to uncover coal with the minimum initial costs with reclamation planning and earthworks being done as an "add on" task. The landform is too steep to remain stable, has no drainage and frequently has areas of excessive acidity or alkalinity. Extensive earthworks are required to reduce grades to an acceptable level and create a drainage system. The flexibility available to the mining engineer to alter the post mining landscape clearly depends on the mining methods. Straight dragline stripping provides virtually no flexibility. However most mining operations over the term of current ten year plans have a substantial pre-strip component. It is this pre-strip material which has the potential to reduce the final reshaping earthworks. The reshaping operation itself is subject to some flexibility with various options being available to re-grade and provide drainage. The full utilisation of this flexibility to minimise earthworks cost should be the aim of reclamation design. ACIRL's current thrust in reclamation is aimed at the integration of mine planning and reclamation earthworks. This involves gathering all environment and agricultural criteria and designing the earth works necessary to produce an acceptable final landform. A key component of our work is the use of computer aided design (CADD) for the design of spoil piles, pre-strip dumps and spoil re-shaping. This approach has been applied to a number of mine sites with earthworks operations covering hundreds of hectares and hundreds of millions of cubic metres volume. We are continuing to provide that consultancy service and at the same time are involved in the development of more sophisticated software tools to apply to reclamation design.

Jan 1, 1991

By J. A. Norden

MUCH has been written concerning the hoisting equipment of various mines -throughout the country, but most of the literature on the subject, if not all, describes equipment of extraordinary capacity and the small and medium-sized outfits have been neglected. The hoisting equipment here described is capable 'of handling about 1200 tons per day. It has not been worked, to capacity, but 600 to 700 tons, together with men and materials, have been handled in two shifts without any great effort. Only one shaft extends from the surface to the lowest levels of the mine; see Fig. 1. It is composed of three compartments, two of which are used for hoisting and the third for water, air, and electrical lines, and for sinking purposes. In 1909, this shaft was raised from the 1000-ft. (304-m.) level to the 700-ft. There a station was cut and an air hoist installed. At this time all mining operations were confined to the upper levels of the mine; that is; above the 700-ft. The. ore was-dropped to this level through chutes from the 300-, 400-, 500-, and 600-ft. levels and then lowered in cars on cages to the 1000-ft., which is the main haulage adit, the mill and railroad bins being about 3000 ft. from the shaft. Orebodies were, in due time, developed on the 1000-ft. level and below. Therefore, in 1913, the shaft was sunk to the 1150-ft. level and thereafter sinking was continued at regular intervals until the 1500-ft. level was reached. But, hoisting from the 1300-ft. level was a difficult, and slow process with the antiquated air hoist, so, in 1916, it was derided to raise the shaft to the surface and install a modern, electrically operated hoist. This was completed early in 1917 and the hoist was in operation in March of that year.

Jan 8, 1920

The Barmac autogenous crushing mill is one of the most successful new comminution technologies to become available to the mining and industrial minerals industries in this decade.The Barmac autogenous crushing mill is an innovative Vertical Shaft Impactor which operates in essence like a high intensity dry ore centrifugal pump with the reduction occurring primarily as a result of high velocity rock to rock impact in a fully rock lined crushing chamber. With applications in a wide range of mining and industrial minerals operations the Barmac autogenous crushing mill presents an opportunity to enhance reduction and liberation whilst providing many cost savings and production increases in new and existing plants.This paper briefly describes the operation of the Barmac autogenous crushing mill and reviews its benefits.

Jan 1, 1990

By Shinroku Matsuzaki

Data the measurement sensor installed with spatial distribution on the blast furnace were successively accumulated online from the process computer to the database system over a long period. This is a new system that accurately considers the relation with the installation position of each sensor, and picture computerization of the measurement data was developed. The overall operation state of a blast furnace, which skilled operators can see in their mind?s eye, was objectively visualized as pictorial information.

Jan 1, 2006