Search Documents

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems. It is equally important to realize that most coal mines will require one or more conventional loader setups in the plan of total mechanization. Seam variations, adverse physical conditions, and special designs of main headings for haulage and ventilation, to name only three reasons, may render 100 pct use of continuous miners uneconomical. Of course, this situation may change. In one mine, prior to 1954, machines that ripped coal from the face achieved only average results, as compared to the impressive performance of boring-type units in another coal mine. A boring-type unit was therefore selected for the first mine in the belief that the chance of success would be greater if it were used in a combined cutting and wedging operation, cutting a full face in its forward movement. The miner was located in a part of the mine where a special projection could be readily developed, a solid area scheduled for mining according to the overall progress plan. All openings surrounding the particular area were carefully investigated for the presence of sulfur balls. Fig. 1 (opposite) shows the representative seam section, containing the several pyritic bands 1/4 to 1/2 in. thick; a characteristic Pittsburgh seam parting averaging 5 to 6 in. of slate, coal, and slate; and the occasional py-rite lenses 2 to 3 in. thick. Under normal conventional mining methods, the top 10 or 12 in. and the bottom 4 in. are left in place to offer roof protection

Jan 1, 1958

Controlled Source Audio Magnetotelluric (CSAMT) surveys were carried out by Glass Earth (New Zealand) Limited (Glass Earth) in 2006 - 2007 to investigate epithermal gold targets in the central North Island of New Zealand. The surveys were conducted using a Zonge GDP 32 8-channels receiver and a Zonge XMT 32 transmitter powered by a 16 KW generator. The electric field dipole was maintained at 20 m length (five dipoles per 100 m spread) and the frequency ranged from 4 KHz to 4 Hz. Only scalar (TM mode) signals were recorded, using one magnetic coil per spread. The transmitter bipoles were 1 - 4 km in length and located about 5 to 10 km from each survey area.   Sixteen individual target areas were surveyed by June 2007. The CSAMT survey lines (100 - 400 m spacing) were determined mainly on results from previous ultra-detailed airborne magnetic and gravity surveys conducted by Glass Earth in 2005. The data from each CSAMT line was carefully examined to remove any spurious signals and processed using Zonge SCS2D software, which can produce smooth 2D resistivity inversions of the field data. The results were presented as resistivity sections and maps to help the identification of exploratory drilling targets, mainly from the existence of subsurface high resistivity zones (resistors) that can be interpreted as caused by silicification associated with epithermal mineralization.   An example of processing and interpretation of the CSAMT data is presented in this paper on results from Glass EarthÆs Tahunaatara target, where CSAMT surveys have identified zones of epithermal mineralization confirmed by exploratory drilling.

Jan 1, 2007

By David B. Campbell

INTRODUCTION This submission was made to the Royal Commission of Inquiry into uranium mining in British Columbia. It discusses the stability of waste rock piles that might be developed in conjunction with uranium mining and the control of leachates that might be generated within these waste rock piles over the short and the long term. Short term refers to the interval during which a waste rock pile undergoes either continuous, or alternatively intermittent development, and in general can be considered to extend over the operating life of the mine. Long term refers to the postmining period, i.e. after the ore-body has been exhausted, and mining operations have ceased. Two major classes of waste material are generated in the course of mining and milling operations. Tails, which are the solid waste materials produced by the milling operations commonly exit the mill in slurry form and are stored in tailing retention ponds. Management and control of these slurried wastes are the subject of other papers to the Commission and this conference. In the course of the mining operations, it may be necessary to remove rock materials that are below cut-off grade. That is, ore concentrations within some of the mined rock may be lower than the concentrations which on the basis of economic considerations justifies milling the material. Rock which is removed in the course of the mining operations, but which is below cut-off grade is referred to as waste rock. This waste rock is commonly consigned to a specific area for disposal where it is placed in a mound or pile, i.e. a waste rock pile. Ore concentrations within the waste rock may vary from zero to just below cut-off grade. Since an increase in the market value of uranium could at some time in future result in reduction of the cut-off grade, it follows that waste rock containing ore concentrations slightly below today's cut-off grade could become ore grade rock at some time in future. For this reason, the mine operators may deem it advisable to separate waste rock according to grade, and to consign the waste rock to two or more individual waste rock piles. For purposes of clarity and simplicity, this submission treats the stability of waste rock piles and leachate control in a manner which assumes that these potential problems are isolated and separate from other aspects of the mining and milling operations. For many site specific cases, the problem of potential leachate control might be integrated with the tailings management aspect of the project, thereby realizing economic benefits while at the same time reducing the potential for adverse environmental impact.

Jan 1, 1980

By J. W. Hickman, E. A. Gulbransen

In a previous paper' the authors have investigated the structure of the oxide films formed on most of the metals that make up the alloys of this study. The metals were studied in order to provide basic information on the structures, both physical and chemical, of the oxide films and to determine how these structures are effected by the temperature, time of oxidation, and surface preparation. It was felt that an understanding of the physical and chemical structure as well as the stability of the oxide film might furnish clues as to the nature of the reaction process and the protective quality of the film. The oxidation of the metals was studied over the temperature range 300' to 7o0°C. except for copper, wherc the range selected was 100' to 500°C. The results of these studies were presented in graphical form as existence diagrams of the oxides on a time-temperature scale. For some of the metals the existence diagrams were simple and showed few chemical transitions, but there were numerous cases where the physical state of the oxide surface was a function of time and temperature. In general the physical state of the oxide surface changed with increasing temperature so as to increase the sharpness of the diffraction patterns and to cause orientation effects to be more pronounced. Deviatiois in lattice Darameters from X-ray values were noted. In general these deviations were of positive nature and may be due to solid solution of the metal in the oxide lattice. This effect might be expected in thin oxide films. In a study of the oxidation of alloys containing two or more metals, there may arise the complicating factor of identification of the oxides formed. A thorough understanding of the oxides formed on the pure metals, therefore, was, essential before investigation of the oxidation of alloys. In this paper it is our purpose to present a study of the following problems: 1. The existence diagrams of various alloys. 2. The effect of the structure of the alloying metal on the existence diagram of iron. 3. The effect of the percentage of chromium on the oxides formed on Fe-Cr alloys. 4. The relationships, if any, between the oxides formed and the protective quality of the oxides. The following alloys are included in this study: alloys of iron with body-centered cubic, face-centered cubic and other metals, 13 Cr-Fe, 18-8 stainless steel, K4²B, Nichrome V, Hipernik, Inconel, Stellite "²I," Refractaloy, Kovar, mild steel, a series of Cr-Fe alloys and a series of Co-Fe alloys. Since many of the commercial alloys in this list contain more than two metals, various complicating factors in the identification of the oxides formed may arise.

Jan 1, 1947

By Charles D. Borror, George K. Foster

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By M. F. Hawkes, R. F. Mehl

The rate of isothermal transformation of austenite to pearlite depends upon the rate of nucleation, N, and the rate of growth, G, of pearlite in austenite. Values of N are given in terms of the number of nuclei forming in unit time per unit grain boundary area of unreacted austenite; values of C are given in terms of the linear rate of radial growth. Variations in the isothermal rate with temperature result from variation of N and G with temperature. Depth of hardening of a steel depends fundamentally upon values of N and G; changes in carbon and alloy content effect changes in N and G and thus affect depth of hardening. Quantitative studies are available on N and G for the formation of pearlite in plain carbon eutectoid steels.3 Systematic studies in this field are necessary if the phenomena are to be well enough known to furnish a proper basis for full rationalization and for theory. Accordingly, the studies are continuing, both with respect to the effect of alloying elements upon the values of N and G in the formation of pearlite and to the values of N and G for the formation of ferrite in hypoeutectoid steels. The present paper is the first relating to the effect of alloying elements upon the values of N and G for pearlite. It offers special interest since cobalt is known to have an anomalous effect upon the rate of formation of pearlite, accelerating it, whereas all other elements retard it.4 It will be shown that cobalt increases both N and G for pearlite and that this effect is inherent in the Fe-Co-C system and not dependent upon factors relating to austenite heterogeneity nor upon any recognizable adventitious factor. Inasmuch as the rate of diffusion of carbon in austenite and the interlamellar spacing of pearlite are variables related to G and possibly to N (in a manner not yet certain), measurements of the effect of cobalt upon them are also reported here. In the course of the work, measurements were made on the effect of cobalt upon the marten-site temperature and these are given. COBALT AS AN ALLOYING ELEMENT IN STEEL Properties of Cobalt Cobalt resembles iron more closely than does any other chemical element. Its atomic number is 27, hence it is the element immediately following iron in the periodic system. The two differ in atomic structure only in the fact that cobalt contains seven electrons instead of six in the third, or transition, level of .the third shell. The next shell, which is the

Jan 1, 1948

By T. S. West

Completion and production data presented for three wells in the Oakville area of Live Oak County, Texas, which were completed near the gas-oil or water-oil contact, indicate that coning may not be as prevalent a cause of failure in such cases as is commonly assumed. Failure in the cases discussed is indicated to be due instead to: (I) erosion of the formation, (2) flowing out of mud filter cake, or (3) failure of the cement. An open-hole gravel-pack type of completion procedure is proposed for preventing failures of this kind by preventing movement of all solid material in the space in which completion is made. Various combinations of layers of gravel, sand, and cement are utilized for this purpose. Experimental results and theoretical discussion as to the applicability of gravel pack completion are included. Introduction This paper is primarily a study of the reasons for failure of oil-well completions near the gas-oil or oil-water contact, and suggests a procedure for increasing the efficiency of this type of completion. The value of improvement in completion effectiveness near the gas or water zone is not confined, however, to wells of relatively thin oil columns. Thick oil columns become thin as depletion progresses. It would seem to follow that the minimum distance from the gas or water zone at which completion can be made in a new well indicates the limit to which depletion may be carried in a well having an oil column of any initial magnitude. Only four ways can be postulated in which high gas-oil or water-oil ratio can initially occur if the zone exposed for production is within the oil column: 1. Failure of the cementing material. 2. Vertical coning. 3. Failure along the boundary between the cement and the wall of the well. 4. Failure of the formation comprising the wall of the well. Cementing materials such as portland cement and plastics have reached a high stage of development. Failures of this type are probably due almost always to extraneous causes such as mud contamination rather than to faulty cementing material. Vertical coning can and obviously does occur. However, the usual occurrence of thin impermeable streaks in sand sections and the success with which open-hole drill-stem tests can be made near the gas-oil contact suggest that over-all effective vertical permeability, and in turn vertical coning, is less prevalent than frequently is assumed. Much has been written on failure by flowing out of the mud filter cake between cementing material and the formation. A filter cake is always present if, prior to cementing, mud has come in contact with a permeable formation at pressures exceeding the pressure head of the fluid it contains. Mechanical methods are in use for removing filter cake during the cementing operation? which undoubtedly are of

Jan 1, 1947

By George K. Foster, Charles D. Borror

The Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest open-pit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. The Ore Body The ore body is a serpentinized peri-dotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur per- pendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber

Jan 1, 1948

By R. H. Hiltz, R. W. Douglass

Large-grain specimens of iodide titanium prepared metal-lographically were stain etched using the technique of New York University as modified by Watertown Arsenal Laboratories. Orientations of grains showing an abnormal response to stain etching were determined by back-reflection X-ray techniques. X-ray results showed that a-titanium grains, oriented such that their basal planes were parallel to the polished surface, have a slower reactivity to stain etching than any other orientation. Grains oriented such that their basal planes made small angles with the polished surface exhibited reaction rates between that of the true basal orientation and the normal rate. As the angle with the surface increases the reactivity increases up to a maximum angle of 14 deg. Basal planes making an angle with the surface of greater than 14 deg show normal reactivity to stain etching. These data, plus work on polycrystalline specimens, indicate that the oxidation rate of titanium might be reduced by correct alignment of crystal planes. ThE earliest observed phenomenon in the micrography of titanium was the occurrence of a grains which exhibited no birefringency. Even though a titanium possesses a hexagonal-close-packed structure and should be optically anisotropic, it can appear optically isotropic, when the crystal is so oriented that its intersection with the polished surface is perpendicular to the axis of symmetry. During the develoment of color staining techniques for titanium: it was noted that the a phase did not stain uniformly. Staining of specimens of commercially pure titanium resulted in a micro-structure of blue-colored grains, among which were randomly oriented a few grains exhibiting colors between the initial yellow and the final blue color. Under polarized light, these off-colored grains appeared to be optically isotropic. More intense study with polarized light, however, showed only the yellow grains to be isotropic. The intermediate colored grains exhibited weak birefringency, which at first glance is not detectable due to the strong birefringency of the surrounding structure. Aminoff2 and Straumanis3 have previously shown that in zinc the basal orientation is less reactive than other orientations. Leidheiser4 showed the same thing to be true for the hexagonal-close -packed configuration of cobalt. Thus, it would appear that the basal-plane orientation is responsible for the abnormality in stained titanium. Later work by Leidheiser5 on cobalt has shown that other planes besides the basal plane exhibited reaction rates slower than the normal rate. Reported planes were the (100), the (1011) and several planes making small angles with the basal plane. The last observance appears not to be due to the reactivity of the reported plane but due to the reactivity of the basal plane which is very close to being parallel to the surface. There are, then, two possible explanations for the range of colors observed in stain-etched a titanium. Since extensive research on the effect of orientation on surface reaction has failed to provide any definite trend, these two explanations are not adequate in themselves. Planes showing the retarded reactivity differ not only for different crystal structures but for metals of the same crystal structure and even for different reactions of the same metal. Tragert,6 Leidheiser,7 Tammann,6 and wagner9 have shown copper to exhibit retarded reactivity on the (111) plane. However, Leidheiser10 has shown that under other conditions the retarded reactivity of copper is associated with the (100)

Jan 1, 1960

The Highlands Region of Papua New Guinea has 3 major national highways. The locations of these national highways are shown in Figure 1. The Highlands Highway begins at Lae City on the coast and passes through the Highlands towns of Goroka, Kundiawa and Mt Hagen. It terminates at Togoba approximately 10km out of Mt Hagen town. The Enga Highway begins at Togoba and passes through the towns of Wapenamanda, Wabag and Laiagam. It terminates at the giant Porgera Gold Mine. The Southern Highlands Highway also begins at Togoba and passes through the major towns of Mendi, and Tari. It terminates at Koroba station, near the Hides Gas Field. Two separate Feeder roads intersecting the main highway service both the Kutubu Oil Project and the Hides Gas Field. These national Highways play a very important role in the development of Papua New Guinea. Goods and services are delivered to the bulk of the population of the Highlands Region using these highways. Heavy machinery and equipment for the mining and petroleum projects of Porgera, Hides and Kutubu are transported using these roads.

Jan 1, 1997

By A. E. Bellis

ROBERT J. ANDERSON, Cleveland, Ohio (communication to the Secretary *).-The paper by Messrs. Bellis and Hardy was interesting to me and has led me to make a few remarks concerning some of the points brought out. The question of employing correct hardening temperatures is one that is sadly neglected, particularly in many large plants that forge and treat their machine tools for private use. As is most aptly remarked in this paper, "The custom of using one, high-speed temperature for all tools is very poor practice;" still, such practice is more common than otherwise. An instance came to my attention some time ago, in connection with some work with the standardization of high-speed steels for machine tools, where there were no less than six different brands of alloy steels being used for machine tools such as lathe, shaper, planer, boring mill and cutters of like nature. All of these different steels received identical heat and forging treatment-or at least that was the aim of the tool hardener. That the results were highly unsatisfactory goes without saying. That the hardening department of many plants is conducted on a rule-of-thumb fashion is the reason for a great deal of the trouble and disappointment which seems to be the lot of many tool-steel users. Exceedingly crude execution is the rule rather than the exception, and it is no small wonder that the results are as good as they sometimes happen to be. It would seem that at the present price of alloy steels the subject should receive a closer scrutiny by purchasers than it does. One not familiar with the workings of souse plants that disdain to lend an ear to scientific heat treatment would scarcely give credence to some of the methods employed, not only in the treatment of the steel but also in its selection and purchase. Heating for hardening should be conducted under close pyrometric control only after the correct hardening temperature has been determined.

Jan 3, 1917

By J. W. Halley, G. L. Plimpton

BECAUSE of the two distinct stages in the solidification of rimmed steel, segregation in the rimmed ingot is more complex than that in the killed or semikilled ingot. In the earlier stage, chemical reactions, resulting in evolution of gas and vigorous stirring of the metal, effect a degree of negative segregation unique to rimmed steel. The composition of this zone constitutes the principal quality advantage of this type of steel. In the later stage of solidification, after the evolution of gas has ceased, the segregation follows the general pattern of a more completely deoxidized steel. However, the composition of the liquid remaining after the first solidification stage varies markedly from that of the original melt, some constituents having been partially removed as reaction products while the concentration of others has been intensified by rejection from the metal solidifying in the first zone. The aim, from the standpoint of segregation, in rimmed steel of high quality is to effect a maximum negative segregation in the rim zone without excessive concentration of undesirable elements at the center of the ingot. To achieve this aim, the composition of the melt may be varied and the furnace and pouring practice may be adjusted within certain limits. It is the purpose of this study to discuss segregation in rimmed steel from the standpoint of the mechanisms that produce it and to survey the phases of open-hearth practice that influence those mechanisms. MECHANISMS PRODUCING SEGREGATION The mechanisms that determine the degree of segregation in the rimmed ingot are closely interrelated, making it difficult to select the primary factors and to determine a satisfactory order for presenting them. For instance, the question of sulphur segregation is relatively simple, since sulphur is not directly involved in chemical reactions in the ingot; but its concentration in the rim zone is dependent not only on its original analysis in the melt, its segregation coefficient, and the freezing rate, but also on the rate of its removal from the impure film on the solidifying surface. This washing action involves all the factors (such as freezing rate, the carbon-oxygen product, pressure, etc.) that determine the rate of gas evolution and hence the efficiency of film removal. Sulphur distribution between the rim and core is affected by the volumetric ratio between the two zones, and its segregation in the core is a function not only of the freezing rate of the core but also of all the foregoing factors that determine its concentration in the metal when solidification of the core starts. To simplify the presentation, it is proposed to treat the mechanisms affecting segregation independently in this section, reserving a discussion of their over-all effects for the section in which actual segregation data are given. The factors affecting segregation will be treated in the following order: (I) differential solidification, (2) removal of constituents as

Jan 1, 1944

By M. S. Burton, G. V. Smith, A. Rosen

The kinetics of re crystallization and the effect of recovery on recrystallization of pure iron were investigated within the temperature range of 517" to 632 OC. Grain growth and activation energies were also studied. Two stages can be distinguished during recrystallization; the first is gvowth-controlled and the second is nucleation-controlled. The extent to which the first stage succeeds before the second stage begins depends on both temperature of recrystallization and temperature of recovery. The softening of cold-worked metals and alloys due to transformation of the deformed crystals to strain-free equiaxed grains during annealing is well-known, and early inestiators established that recrystallization kinetics is strongly influenced by minute quantities of impurities. Generally, it is believed that impurities decrease the rate of recrystallization and the rate of grain growth. To understand the basic phenomena of recrystallization, investigations should be on pure materials. Most of the research on high-purity materials has been on metals having the fee Bcc materials, and especially high-purity iron, have been studied only in recent years. It is known that recovery may influence recrystalliation;" however, no general description of the influence, applicable to all materials, has been presented. This paper presents results of a study of the recrystallization kinetics of high-purity iron, after 60 pct cold deformation by drawing, with particular reference to the influence of recovery on the rates of recrystallization and grain growth. From observations of these rates, conclusions are drawn concerning nucleation. MATERIAL AND EXPERIMENTAL PROCEDURE Preparation of Material. High-purity iron, prepared by zone refining of vacuum-melted electroiytic iron at Battelle Memorial Institute under sponsorship of the American Iron and Steel Institute, was used in this study. Table I gives the reported chemical analysis of the material, taken at a point near the last molten zone and thereby rep- resenting the maximum impurity level for the entire bar. Prismatic specimens, approximately 10 x 10 X 50 mm, were sawed from the 50-mm-diam bar, perpendicular to the zone-refining direction, and turned to cylindrical shape. These specimens were sealed in quartz capsules under vacuum, approximately 10"e mm Hg, austenitized at 930° C for 15 min, slowly cooled, removed from the capsules, and cold-worked in air by swaging to approximately 20-pct reduction of area. The encapsulating, austenitizing, and swaging operations were repeated two additional times, after which the samples were encapsulated, austenitized, and cold-drawn to 60-pct reduction of area. A further vacuum anneal at 630°C for 120 min and cold drawing to 60-pct reduction of area produced wire 2.8 mm in diameter. The drawn wire was electropolished to remove deformed material on the surface, after which it was sawed into 4-mm-long specimens for the recrystallization study. Microscopical examination before the final cold reduction revealed equiaxed grain structure with very fine grains in a thin layer near the surfaces of the specimen and nearly uniform ASTM 3-4 grain size in the center. Recrystallization Heat Treatment. a) Direct Recrystallization of Cold-Worked The 60 pct cold drawn iron specimens were recrystallized at five temperatures, 517, 556, 590°, 612, and 632C, in a lead bath covered with graphite (the temperature was controlled to 1°C). Specimens were treated for twelve different times at each temperature, and all were water-quenched after heat &eatment. b) Recrystallization Following Preliminary Recovery Heat Treatment. After cold working, specimens were sealed into quartz capsules under vacuum, 105 mm Hg, and recovery-annealed at 362", 400", and 440°C for 20 hr prior to recrystallization. No evidence of recrystallization was found

Jan 1, 1964

By B Mennie, R Poedjono, G Coad

PT Freeport Indonesia operates a large copper and gold mining operation near Tembagapura, Papua (formerly, Irian Jaya), Indonesia. This is a remote location with its own set of unique operational characteristics. The mining and concentrating operations typically produce a concentrate containing 2500 tpd of copper and 6000 oz of gold per day from the combined mining of a 45 000 tpd (ore) block cave operation (DOZ Mine) and a 190 000 tpd (ore) open pit mining operation (Grasberg Open Pit). The Grasberg Open Pit mine will be exhausted in 2015 at which time FreeportÆs operations will entirely underground mining methods. The Common Infrastructure Project (CIP) incorporates the elements required for the shift to underground mining at a production rate approaching 200 000 tpd. The AB Adit portion of the CIP will provide deep level access to the Grasberg Block Cave (below the Open Pit), Kucing Liar, Big Gossan, and the Mill Level Zone orebodies. Commencement of the project was September 2003. The Grasberg Block Cave is planned to start production in 2014. This paper provides details on the project scope, innovative contractual framework, advancement of mining methods throughout the life of the operation, equipment selection, manpower selection, training, geological, and socio-political conditions related to the project.

Jan 1, 2005

By Navid Bahrani

Overview ? Case history of footwall slab failure ? Procedure used to build a finite element model ?? Pre- and post- mining topography ?? Slab geometry ?? Excavation stages ?? Input parameters ? Finite element modelling results ?? Unloading-induced displacements (magnitudes & directions) ?? Calibration of overall model using measured prism displacements ?? Shear stresses and displacements along the base of slab ?? Factors of safety at different stages ?? Effectiveness of rock bolts ?? Staged or unstaged model? ? Conclusion

May 1, 2008

By A. D. Mah

To assist Bureau of Mines research in extractive metallurgy and to add to the thermodynamic data base useful to others, energy calculations were made for 63 reactions relating to investigations on the production of anhydrous aluminum chloride from chlorination of clay.

Jan 1, 1982

The Devonian Mount Morgan gold-copper deposit was situated on the western margin of the Calliope Volcanic Are assemblage, in the northern New England Orogen. Recorded production from commencement of mining in 1882 to mine closure in 1989 stand

Jan 1, 1994

By Neil B. Young

Carbonate minerals constitute a major fraction of the oil shale in Colorado's Green River Formation. Quantification of carbonate minerals is important for the characterization of oil shale, particularly because of their thermal activity in production of oil from shale. The carbonate minerals found in this oil shale are nahcolite (NaHCO3), dawsonite [NaA1(OH)2CO3], dolomite [(Mg1-xFx)Ca(CO3)2], calcite (CaCO3), and ferroan [(Mg1-xFex)CO3]. Although carbonate minerals can be removed by acid extraction from the balance of the oil shale, direct determination of carbonate minerals is complicated by the occurrence of the same cations in more than one mineral. A method for assigning the acid-soluble cations to the individual carbonate minerals was developed from two assumptions based on oil shale geochemistry: (1) Calcite and ferroan do not occur together, and (2) the ratio of iron and magnesium is the same in dolomite and ferroan. These assumptions were tested by the Bureau of Mines by applying the technique for assigning cations to 219 samples from the saline section of the formation. The reported carbonate mineral amounts were compared statistically with X-ray diffraction peak heights, verifying the cation assignment method.

Jan 1, 1975

By Walker E. R

IN the early age of steel it was made hy what is known as the cementation proeess, in which wrought iron was embedded in charcoal and heated in a mufflc furnace to a tcmperature of approximately 1100° C. for varying lengths of time, the length of time depending upon the amount of carbon (or better known in thosedays as the degree of hardness) required in the finished product.By this process the resultant product obtained was not of uniform quality, and because of this uncertainty of quality Huntsman was induced, in the year 1740, to introduee what is known as the crucible process.This process consisted of cutting into small pieces the product of the cementation process, placing these pieces in a crucible, and melting them down with the aid of a eoke-fired furnace, after which the molten metal was cast into suitahly shaped ingots, from which could be hammered any desired shape.A section of crucible furnace is shown in Fig. 1. By this means a product, very uniform in character, was produced.The process is still in use, but, owing to its high operating cost, it is mostly eonfined to the production of very high-grade carhon and alloy steels. Its position to-day as a producer of these high-grade steels is, however, being very seriously challenged by the electric process.It was owing to the excessive cost of crucible steels and the need of producing a steel in commercial quantities and at a reasonable cost, that led Sir Henry Bessemer to introduce what is known as the Bessemer process.

Jan 1, 1930

By M. von Heimendahl, G. Thomas

The microstructure of TD-Ni has been examined by transmission electron microscopy in the extruded, annealed. and deformed states. The tensile properties hove been correlated with the observed microstructures and the results ore com-pared with those obtained from pure nickel. The important conclusions are that the thorin particles in TD-Ni act as strong burriers to dislocntion motion during both deformation (slip) and annealing (climb). During deformation. the dislocations tangle around the particles and a cell structure is devleloped after 10 pct or more strain. The cell size appears to be determined by the spacing of the largest particles and is about five times smaller than that in pure nickel for the same strain. The higher work-hardening rate in TD-Ni compared to nickel is probably due to the more rapid rate of dislocation multiplication in the alloy as a result of dislocation-particle interactions. The Th0,particles inhibit recrystallization and twin growh so that some strengthening may arise from the high density of small annealing twins. THE strengthening of materials due to the presence of a dispersed second phase has been the subject of considerable experimental and theoretical investigation in recent years. One of the newest dispersion-strengthened alloys to be developed is TD-Ni,1 a system of approximately 2 vol pct thoria (ThO2) dispersed in a matrix of commercially pure nickel. This material is fabricated by powder-metallurgical techniques and offers high-temperature stability and useful mechanical properties virtually to the melting point of the base metal. While the mechanical properties of this system have been investigated,2,3 there have been no reports in the literature concerning the microstruc-ture of TD-Ni and its correlation to mechanical properties. This paper describes a transmission electron microscopy investigation of the micro-structure of TD-Ni together with its mechanical properties. The results are compared with the structure and properties of pure nickel.

Jan 1, 1964