Search Documents

By Harold Markus, Gerhard Derge

THE first paper1 of this series described a technique of careful surface preparation by means of which reproducible results may be obtained from potential measurements of the behavior of tin in carbonate solutions with a pH range from 8.4 to 11.2. It then went on to establish the behavior of pure tin electrodes under these conditions and showed that the metal remains active at all times, though the steady potential attained after several hours decreases from I.I2[t] volts at a pH of 12.6 to 0.6 volts at a pH of 8.4. This behavior may serve as a norm with which all other data can be compared. In the second paper,2 small amounts of other anions were added to the carbonate solutions and the conclusion was reached that the common impurities encountered in alkaline materials packaged in tin do not increase corrosion. In fact, in some cases these anions may actually promote the formation of protective films. The present paper rounds out this survey by presenting data on the influence of cations added to the carbonate solutions, as well as the effect of alloy additions to the tin. In many cases the potential data are supplemented with weight-loss measurements. Information is also presented on the effects of some additional anions, the influence of gases above the electrolyte, the behavior of high-purity tin, and the effect of atmospheric oxidation on the corrosion resistance of the above-named alloys. Analysis of the entire body of data discloses some general rules applicable to corrosion in carbonate solutions. The experimental methods used are the same as those previously described. EXPERIMENTAL DATA Cations.-The carbonates of the cations K+, Li+, NH4+, which are soluble, were studied in the same way as the anions, by adding 0.01 mol of the metal carbonate to one liter of 0.2 M sodium carbonate solution, pH 11.2, or to 0.1 M sodium bicarbonate, pH 8.4. The other metallic carbonates are only slightly soluble, of the order of 0 7-3 mols per liter or less, and the sodium carbonate solutions were saturated by adding excess reagent several days before the experiment, shaking frequently, and filtering just before use. The chemicals were c.p. grade in each case except the indium salt. This salt was prepared by solution of the metal in hydrochloric acid and precipitation by addition of Na2CO3. These cations may be divided into two classes, according to their effect on the potential behavior of the tin: (I) normal, (2) passive. To offer a basis of comparison, curves I of Figs. I and 2 are given to illustrate the behavior of tin in carbonate solutions saturated with CaCO3. These curves are the

Jan 1, 1941

In order to satisfy environmental and mine operational requirements it is becoming increasingly important to minimise ground blast vibrations at certain locations. These locations are often in soil or on large resonant structures such as grain silos, highway bridges or even the walls of an open pit. A soil monitoring exercise was carried out to evaluate the common practice of coupling vibration detectors to the ground using spikes. At a series of locations in an operating quarry the spiked array response to single blastholes was compared with that of an accelerometer array attached to a calibrated embedded mount. The results clearly showed that the spiked arrays over-estimated the true ground vibration by 46.5 per cent on average, with a maximum observed error of 99.2 per cent. These errors are considered too large for compliance monitoring where accurate vibration levels are required for comparison with prescribed limits. Although spike coupling is convenient, its use for compliance monitoring should be viewed with caution. Unfortunately, however, many manufacturers supply their detectors as spiked arrays. A structural monitoring exercise was also carried out to evaluate the vibration response of a grain silo, highway bridge and a pit wall to the initiation of single blastholes. In this case accelerometers and standard geophones were firmly attached to the bridge which resonated at low frequencies. The results clearly show that, due to their limited low-frequency response, the geophones typically measured only half the true vibration level as measured by the accelerometers.

Jan 1, 1995

By Edgar Stansfield

ONE of the most striking features of the coal series passing from peat through brown coal, lignite, etc., up to anthracite is the gradual reduction of moisture content with the increased coalification of the original plant material. Thus drained peat from a bog may contain 90 per cent water, brown coal contain 50 per cent, lignite 30 per cent, while a bituminous coal may contain only 1 per cent moisture. Moisture, therefore, is one of the important factors to be considered in coal classification, especially with the lower rank coals. With bituminous and higher rank coals the moisture content is less satisfactory for classification; it may even pass a minimum value and then increase with increasing rank to anthracite and superanthracite. Coal in an undisturbed seam contains moisture which is an integral part of the coal, but it may also be wet with free, underground water percolating through the seam. Only the former must be considered in evaluating the moisture content of the coal for classification purposes; this will be called the "true moisture" of the coal. When the seam is mined and sampled the sample taken may show the true moisture; on the contrary, it may contain in addition free mine water or, especially in dry, well ventilated mines, it may contain less than the true moisture. Coal contains unstable organic compounds which may decompose, with the production of moisture, when the coal is exposed to air at ordinary temperatures, or is heated with or without exposure to air. The potential moisture of a coal therefore is higher than its actual moisture. The lower the rank of the coal, the greater its instability, as a rule, and the greater the care necessary to avoid oxidation or decomposition in any investigation of moisture content. The majority of coal workers have preferred, on account of the difficulty in evaluating the true moisture of a coal, and for other reasons, to classify coals by analyses calculated to the dry-coal basis. A number of workers familiar with lower rank coals have recently insisted that the classification of such coals can be satisfactory only if analyses on the moist-coal basis are employed. The moisture-holding capacity of coal is therefore intimately connected with coal classification, and in this paper a procedure is outlined for determining the true moisture of a coal.

Jan 1, 1932

By H. W. Kilau

The U.S. Bureau of Mines examined the wettability of bituminous and subbituminous coals before and after exposure to ambient air atmosphere, as part of an ongoing project investigating the coal-wetting abilities of surfactant solutions intended for the suppression of dust during coal mining operations. Exposure periods were generally 7 days or less, and the changes in wetting response were measured with a capillary penetration apparatus. Wetting solutions tested included a nonionic surfactant, two anionic surfactants, and pure distilled water. After exposure, higher ranked bituminous coals treated with nonionic surfactant solution and pure water showed increased wettability, but lower ranked subbituminous coals showed decreased wettability. With the anionic surfactants, the coals demonstrated opposite responses. The wettability changes appeared to be related to the coal moisture content. These changes may be amplified by specific, but incompletely understood, interactions between surfactant polar groups, absorbed water, and the coal surface.

Jan 1, 1989

By H. J. Gluiskoter

The chlorine content of the coals in the Illinois Basin ranges from 0.00% to more than 0.60%. The chlorine content of the Herrin (No. 6) Coal has been mapped on a regional scale and, in general, increases with the depth of the coal. The depth-chlorine correlation exists because the coal is in apparent equilibrium with the composition of the ground water associated with it, and the salinity of the ground water generally increases with depth. At least part of the chlorine can be easily removed from the coal in the laboratory. In a natural weathering experiment, chlorine values decreased markedly during an 8-week period. Results to date indicate that none of the coals studied has a sufficiently high chlorine content to make it unusable in high-temperature steam boilers, although special steps may be necessary in the preparation or utilization of some of the highest chlorine coals. Investigations into the occurrence and distribution of chlorine in Illinois coals have been in progress at the Illinois State Geological Survey for over 35 years. Since 1948, chlorine analyses of face channel samples and of drill core samples of coal have been made routinely. The increased interest in chlorine and alkalies in coal in the U.S. followed that in Europe, where power plants during World War II were called upon to produce at higher levels than previously and with less down time for maintenance. Higher steam temperatures were reached, resulting in increases in the amount of fouling of external heating surfaces and in corrosion of boiler tubes when high chlorine coals were used. Early studies of the problem showed that coals with high chlorine content were more likely than those low in chlorine to cause difficulties in installations fired with powdered fuel. Crossleyl reported that the first rule of thumb developed for British coals was that coals considered to be high in chlorine (more than 0.30%) caused the most trouble, those intermediate in chlorine content (0.15% to 0.30%) were less likely to cause difficulties and those low in chlorine (less than 0.15%) generally were not associated with alkali bonded deposits and corrosion. However, this relatively simple picture was not adequate to characterize the difficulties that could be expected during the utilization of a large number of coals and Crossley1 developed another scheme for assessing the chances of superheater corrosion. This scheme took into consideration the observation that coals high in sulfur as well as chlorine are more likely to cause corrosion and fouling than coals low in sulfur and high in chlorine. Crossley also considered the ash content. When two coals had the same chlorine and sulfur contents, the one with the greater amount of ash would be the less likely to cause difficulties. Knowing only the amount of chlorine in a coal obviously will not give all the answers. Indeed, the significance of the chlorine content has been much discussed and it has been suggested that perhaps the total alkalies are a better indicator of possible troubles. The observation that the deposits that form

Jan 1, 1968

By Ian Wark

IT has been shown1 that in the absence of heavy metal salts, the nature of the alkali used to promote differential flotation-whether caustic soda, lime or sodium carbonate-is unimportant. The hydroxyl ion is the active depressant upon which differentiation depends, and the pH value determines whether a film of collector forms on any given mineral surface. Even when sodium cyanide is used in conjunction with alkalies, it is the pH value and not the nature of the alkali or its concentration that is important, for upon the pH value alone depends the fraction of the added sodium cyanide that is present as cyanide ion, which is the true depressant. When heavy metal salts become dissolved from partly oxidized ores, or are added intentionally as activators, conditions are different, and metallurgists have found that lime and sodium carbonate do not give identical results, even when added in amounts sufficient to produce the same pH value. In the few instances in which we had attempted to confirm this view, we had failed to do so, for, with nothing to guide us, we had inadvertently chosen solutions that gave contact curves of a "stand-ard type," which correspond to conditions of ready floatability. Now, however, we find that, in the presence of copper salts, and within a restricted range of reagent concentrations, the nature of the anions present is important, and that sodium carbonate does influence the results, apart from the usual effect due to its influence on pH value. With the recognition of this anion effect, and with the control of temperature already introduced,' it appears that the factors of major importance in connection with this set of reagents have been taken into consideration, and that the results obtained and the conclusions drawn from contact tests will be of more immediate value to the operator.

Jan 1, 1939

By Scott Scovira, Ruilin Yang

This paper presents a non-waveform blast vibration model for the near-fi eld. The model uses the concept of a dominant charge augmented by other contributing charges estimated using a scaled time window. The model accounts for the effect of broken ground created by earlier fi ring holes, amplitude attenuation, effects of signal broadening with travel distance from frequency attenuation, as well as asynchronous propagation of different wave types due to the wave velocity difference, the delay time effect, and non-linear superposition of near-fi eld vibration. The model uses an effective distance defi ned from the broken ground screening, and determines a dominant charge contributing to the PPV at a monitoring station. Then the model uses a time window for each individual charge to determine if it contributes to the PPV. The time window has a variable width to model the effects of the signal broadening with travel distance. For modeling the signal broadening, a generalized rock quality factor Qd is proposed. The time window includes a weighting function that diminishes the contribution for charges fi ring further from the dominant charge and this accounts for contribution arising from the timing difference between a contributing charge and the dominant charge. The model uses a non-linear charge weight superposition technique that scales the charge weights within the time window to the same distance of the dominant charge and superimposes the scaled charge weight. The case study demonstrates that the model provides useful predictions for near-fi eld blast vibrations.

Jan 1, 2008

By Finlayson E, Hilyard D

1:100 000 geological mapping of Bougainville Island has resulted in refinement of stratigraphic subdivisions and relationships. We subdivide the sequence into basement Atamo Volcanics (Late Eocene-Early Oligocene), consisting of spilitised pillow basalts, which are overlain unconformably by Late Oligocene-Early Miocene Keriaka Limestone. The latter is unconformably overlain by fine-medium grained volcaniclastics and minor lavas of the Middle-Late Miocene Toniva Formation which coarsens upward and passes gradationally and conformably into the coarsely volcanolithic latest Miocene-Pliocene Arawa Conglomerate. The Kupei Complex, host to the Panguna.porphyry Cu-Au deposit, consists of medium - K20 microdiorites, granodiorites, and andesites intruding Arawa Conglomerate and Toniva Formation. K/Ar isotopic dates on the Kupei Complex range from 4.8-1.3 Ma, and hence overlap the age of the Arawa Conglomerate. We believe that the Arawa Conglomerate consists of mass flow deposits on a volcani- clastic apron surrounding a volcanic edifice above the intruding Kupei Complex.

Jan 1, 1990

Pillar mining methods at the Pasminco Mining Broken Hill Operations are not new. Since mining commenced on Pasminco's leases at the turn of the century virtually every pillar extraction method tried throughout the world has been used. Much of the remaining mineral resource in the Pasminco Broken Hill leases is contained in pillars.However, due to the on-going need for mechanisation with bulk mining methods, and the very peculiar physical circumstances surrounding the formation of these pillars, their exploitation requires the development of a virtually new method based on excavation technology not previously used in the Australian mining industry. Trials of the method are to take place at the southern operations during 1991.

Jan 1, 1992

By Andrew Bamber

The mining and beneficiation of minerals is the second largest end-use of electrical power on the planet, and comminution is by far the largest single contributor to this. Several jurisdictions, including British Columbia, have, in response to concerns about greenhouse gas emissions and climate change, adopted energy conservation legislation, including carbon taxes, carbon trading and conservation incentive schemes. Key to achieving conservation objectives is firstly an understanding of usage metrics across the various unit operations in the sector, and secondly an understanding of the conservation potential represented by available technologies and approaches in reducing end-use. This paper presents the results of a recent utility-funded study on energy use metrics and conservation potential at large open pit mines which are typical of the sector in BC.

Aug 1, 2013

By Kjell Lidin, Christer Nordström

INTRODUCTION LKAB produces iron ore in several mines in northern Sweden, and has been doing so for nearly 100 years. Total production to date is 600 million tonnes of finished products of various kinds (pellets, lump ore, fines). Close to 400 million tonnes have been produced by sublevel caving. This method has been the company's standard method for more than 20 years. A review of the development of equipment over the past 15 years and an outlook up to about 1990 leads to the following general re- flections concerning probable trends. Trends for all equipment are increasing precision and stricter environmental requirements will necessitate cabs, remote control etc to an increasing extent. Conventional sublevel caving can be broken down into the following unit operations: 1. Planning incl prospecting drilling. 2. Horizontal drilling. 3. Fan drilling. 4. Charging and blasting. 5. Loading and haulage at sublevels. 6. Ore drawing in chutes. 7. Rock reinforcement. 8. Production service. This lecture will deal in brief with each of these unit operations and the trends we are experiencing for them. A number of slides illustrating equipment

Jan 1, 1981

Having provided basic data in the main paper I would now like to move on to discuss these areas in broader terms and to examine the various coalfields in terms of their tectonic setting and depositional environment and ultimately to make some brief comments on the factors which may have controlled deposition.

Jan 1, 1975

The objective in design of an excavation in a jointed rock mass is to achieve a prescribed degree of control of rock mass displacement around the excavation. Any excavation in jointed rock usually involves slip and separation along discontinuities as well as translation and ro- tation of constituent rock blocks. Thus, any acceptable model of behavior around an excava- tion must be capable of simulating the force displacement paths followed by the constituent elements, including rigid body translation and rotation. The distinct element method models such behavior by simulating the rock mass as an assemblage of rock blocks which interact through corner and edge contacts. Discontinuities are regarded as boundary interactions between blocks with joint behavior prescribed for these inter- actions. Introduction of structural element logic allows a variety of installed support sys- tems to be modeled. The response of the support to axial, transverse, and flexural loads is based on explicit algorithms similar to those used in the distinct element formulation. This allows large displacements and rotations and general non-linear constitutive behavior for both the support elements and the interface with the rock. This paper describes both the distinct element and structural element formulations and demonstrates several applications involving sup- port interaction with jointed rock.

Jan 1, 1987

By Quinn P, Huuskes W

Continued extraction of the No. 3 Seam at Elouera Colliery required the driveage of a sequence of roadways within an area of significantly elevated horizontal stress. Initial roof conditions varied from excellent to very severe as the panel entered the high stress area. The variation was attributed to the extraction sequence, with different roadways "leading" the panel into the high horizontal stressfield.This paper summarises field and analytical work designed to evaluate the use of stress control methods as an effective planning tool. The "leading" roadway of the panel would be required to remain stable whilst experiencing moderate to severe deformation whilst the neighbouring roadways (stress relieved) could be driven at more acceptable advance rates using less reinforcement.The planning implications of developing the panel with stress control methods are discussed.

Jan 1, 1998

By Gheorghe Oncioiu

The phenomena developed on the influence of thick coal seam no.3 mining, by horizontal slices and rocks caving roof control, in the Jiu Valley coal basin, are very complex. By analyzing the influence volume of underground faces and defining the stress and strain zones, around the faces, it is possible to evaluate the suitable powered support performances. Also, Jiu Valley thick coal seams involve about 50% of reserve balance in the main safety pillars of social, industrial and natural objectives, situated on the mining surface perimeters. For a correct design and drawing of main safety pillars complex research was done with the aim of establishing the subsidence parameters. Upper face rocks medium could be assimilated as a granular medium, which is in a permanent movement. For describing the rocks movement, respectively the ground surface displacement, was taken into account the stochastic mechanics principles. The theoretical solutions are in accordance within situ measurements.

Jan 1, 1999

By R. H. Hawkins

AN investigation of the applicability of geophysical methods to north-ern Ontario lignite deposits was undertaken early in 1930 by the Ontario Research Foundation at the request of the Ontario Department of Mines TABLE 1.-Formations Associated with Moose River Basin Maximum System Formation Lithology Observed Correlation Thickness, Ft. Pleistocene Marine clays 150 Glacial till (Minimum Interglacial 30) clay and peat Glacial till Lower Cretaceous or Mattagami Fireclay, sand 138 Kootenay (?) Upper Jurassic. and lignite Devonian (Upper) Long Rapids Petroliferous, 50 Portage and black and gray Genesee shale Williams Limestone and 87 Tully (?) Island calcareous shale Devonian (Middle).... Abitibi River Gray fossiliferous 65 Onondaga limestone Devonian (Lower) ?... Moose Rive- Limestone and 50 gypsum Devonian (Loner) Sextant Arkose, clay, etc. 50 Pre-Cambrian Syenite, granite gneiss, etc. Igneous intrusives. . Lamprophyre dikes cut the Abitibi River and lower formations. (Permission of Ontario Dept. of Mines) and was financed in part from a research grant made by the latter organ-ization. The work to date has included gravitational, magnetic and electrical resistivity studies. The gravitational and magnetic measure-

Jan 1, 1933

By E. V. Potter, E. T. Hayes, H. C. Lukens

LARGE volumes of hydrogen are liberated at the cathode during electrolytic precipitation of manganese. Most of the gas escapes from the electrolyte, but a considerable amount may be entrapped in the manganese plate. Gas has been observed to escape from manganese melts in puffs that ignite at the surface. It has been reported that castings made with electrolytic manganese tend to rise in the molds; for this reason the manganese is often treated to remove hydrogen before the melt is made or it is premelted and used as cast manganese in making the alloys. The effect of hydrogen on the properties of manganese and its alloys is not known, but its effect on iron and iron alloys has been studied extensively.1.2 The close relationship between iron and man¬ganese suggests that hydrogen may have a similar effect on the properties of manganese and its alloys. The purpose of this investigation was to determine the amount of hydrogen or other gases in typical commercial electrolytic manganese sheet and to investigate ways of removing it most conveniently. APPARATUS The apparatus used is shown schematically in Fig. I. It consists of a chamber A in which the metal sample is placed, a vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The specimen chamber was made of two concentric quartz tubes. The outer one, a, connects with the closed gas system and is surrounded by the furnace G. A second tube, b, fits closely inside a and has a small end that projects into the space for the specimen and holds the thermocouple for measuring the temperature of the sample. The inner tube is joined to the outer tube outside the furnace, with rubber tape and sealing wax, to prevent gas leakage into or out of the closed system. This type of specimen container is loaded very easily and can be used several times if molten metal does not come in contact with the quartz. An ordinary mercury manometer B is used to measure the pressure in the system. The volume gauge C is essentially another mercury manometer, but the volume of the column is much larger than normal and the height of the mercury can be varied by raising or lowering the well H. In this apparatus the tube had a volume of I00 c.c. for a 60-cm. length. For larger changes in gas volumes; auxiliary containers F were used to increase the volume of the system by known amounts. Valves were arranged so that these auxiliary containers could be filled from the system and evacuated by the pump as often as necessary to accommodate the increases in the volume of gas in the system. The furnace G, used to heat the samples, was equipped with an automatic temperature controller, which maintained the desired temperatures within ± 5°C.

Jan 1, 1945

By James Douglas

The Copper Queen mine was opened in 1880 by Messrs. Martin, Ballard & Reilly, and the first copper-furnace was blown-in on August 20th of that year. Prior to that summer nothing but prospect-work had been done on the copper Queen and on a number of adjacent claims. In fact, it was a small deposit, not of copper-ore, but of cerussite, which still remains undeveloped, on the western slope of the Queen hill, which

Jan 1, 1900

By C. F. Nagel

THIS paper is written primarily for those who are familiar with the processes mentioned but who desire a further insight into some of the fundamental principles. It does not give a complete description of the various practices employed in the working of aluminum and its alloys, but presents a few illustrations of the essential respects in which aluminum differs from other common metals, and emphasizes the controlling factors of the processes under consideration. HEAT TREATING Certain aluminum alloys are capable of having their mechanical properties greatly altered by a heat-treatment process. The degree of this improvement may be illustrated by some typical properties of duralumin (Table 1). It is essential that the material be in the wrought condition in order to obtain maximum heat-treatment effects. [ ] In the case of duralumin, the process consists of heating the metal to a prescribed temperature and then quenching it. Immediately after quenching, the material is relatively soft though not as soft as in the annealed state. If allowed to stand at room temperature, the material changes, increasing in hardness and strength without loss of elongation, but at the expense of the plasticity. This action is very rapid at first, gradually diminishing in intensity and to all practical purposes being completed in about four days. This process of hardening is termed

Jan 1, 1928

By C. K. Chabedi

"This paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield. The resources occur at a depth greater than 250 m and the thickness of the coal is roughly 110 m, but the top 50 m comprises coal intercalated with shale and the bottom 60 m contains five seams with sandstone and shale partings. Various factors affecting multiple seam mining at these great depths are discussed with reference to lessons learned from local and international experience on multi-seam mining. Field geological and geotechnical data was utilized to assess the stability of the roof of the seams. There is no specific rock mass rating for the Waterberg area, therefore approximate coal mine roof rating (CMRR) values were used to propose appropriate support strategies. Analysis of Multiple Seam Stability (AMSS) was used to analyse the strength of the parting or interburden between the various seams, the mining sequence, and the interaction between the various seams.The research indicated that it is possible to mine seams with a low CMRR at high mining rates using longwall mining, although support for gateroads is expected to be expensive, time-consuming and onerous to install, and will impact gateroad development rates. It will not be possible to simultaneously mine zones in close proximity and failure of the interburden is predicted, thus dangerous mining conditions are anticipated. However, it will be possible to mine just two of the eleven zones using longwall mining. IntroductionThis paper discusses the difficulties associated with the potential exploitation of the deep multi-seam resources east of the Daarby fault in the Waterberg coalfield using bord and pillar and longwall mining. Figure 1 illustrates the location of the Waterberg coalfield relative to other coalfields in South Africa, while Figure 2 shows the areas containing deep and shallow resources. The Waterberg resources are expected to contribute to South Africa’s future energy requirements, and are currently exploited at the Grootegeluk open pit mine. Grootegeluk produces coal mainly for a power station, with the higher quality product supplied as metallurgical coal. The deposit is technically unique and challenging, being a multi-seam coal deposit with a total of 12 seams over a thickness of 110 m as shown in Figure 3, including Zone 5. There is currently limited knowledge on the multi-seam mining of the deep Waterberg resources. Multi-seam mining utilizing the bord and pillar method has been practised in South Africa before, but at a depth of less than 100 m in the Witbank coalfields. Multi-seam mining in thin seams has also been performed in the Natal coalfields at a depth of less than 160 m, but mostly using bord and pillar mining and secondary mining (partial pillar extraction)."

Jan 1, 2016