Search Documents

By D. J. Reed

Concord coal mine near Bessemer, Ala., built, owned, and operated by Tennessee Coal & Iron Div., U. S. Steel Corp., produces only a metallurgical grade for use as coke in blast furnaces of the division at the Fairfield and Ensley works. Capacity of the operation is approximately 800 tph, half of which is delivered to the coke and coal chemical plant at Fairfield after beneficiation to metallurgical grade coal. The remaining portion of the mine run is rock and refuse removed during preparation. Concord mine coal is hoisted to the surface coal preparation plant by an underground slope conveyor. The slope conveyor is 2449 ft long and has a lift of 729 ft. At time of installation the Concord mine slope conveyor was the largest single conveyor unit ever made with respect to belt horsepower and total lift. After several years it became necessary to determine the cause of slope conveyor cover wear.

Nov 1, 1956

By J. J. Taute, G. Chisakuta, P. Bwando, G. Mitshabu

"BASF Mining Solutions have developed a new generation of copper solvent-extraction reagents that offer significant benefits over the existing reagents available to the industry today. Initial laboratory studies and pilot-plant trials have shown that these new reagents offer the benefits of a dramatic increase in resistance to degradation and are nitration-proof. This paper details a recent pilot-plant campaign at a commercial solvent-extraction plant. The main focus was to evaluate the copper/iron selectivity, copper recovery and net transfer of the new reagent compared with the conventional oxime reagents. The new reagent displays similar copper recovery and net transfer capabilities from typical agitation leach solutions. The pilot-plant results show a step change improvement in copper/iron selectivity in comparison with the existing modified and non-modified hydroxyoxime reagents used on the commercial plant. INTRODUCTION Copper solvent extraction (SX) from an acidic aqueous solution is typically accomplished using a hydroxyoxime extractant (Jergensen, 1999; Kordosky, 2000; Szymanowski, 1993). There are three hydroxyoximes from which all standard formulations are derived: 5-nonyl salicylaldoxime (NSAO), 5-dodecyl salicylaldoxime (DSAO) and 2-hydroxy-5-nonyl acetophenone oxime (HNAO). In the case of NSAO, it is necessary to use equilibrium modifiers in order to increase the copper stripped from the extractant (Kordosky & Virnig, 2003). Blends of DSAO, NSAO and HNAO are used to cover a wide spectrum of conditions (Kordosky, 2008). Use of modified aldoximes and reagent blends over the last 30 years has influenced the way copper producers and equipment manufacturers have approached the operation of copper plants. Existing solvent-extraction reagents cater for typical pregnant leach solutions (PLS) of copper mining systems which do not have significant effects on the reagent. Table I illustrates the range of copper concentration, pH values, temperature and iron concentrations for different leaching operations. As conditions become increasingly aggressive (i.e., higher PLS temperatures in primary sulfide leach or high iron content), current reagents become less capable of functioning according to expectations. One example is the effect of high iron (Fe3+) concentration in PLS and operating SX to achieve high copper recoveries. The ferric is partially chemically extracted and is transferred to elctrowinning (EW) during the stripping stage. To avoid a build-up of iron in electrolyte, which negatively affects current efficiency, a bleed of electrolyte is required. This bleed leads to excessive consumption of reagents, such as cobalt added to the EW process, and thus increases operational cost."

Jan 1, 2015

By Matthews SM, Gooding JE

N Longhole Open Stope at The Zinc Corporation Mine was developed in an area with large and continuous tension cracks. These cracks resulted fran widespread block subsidence into previously mined areas. The practical problems encountered and their solutions are discussed together with an outline of a new method of stope wall support using large diameter dowels installed sub-parallel to the stope wall.

Jan 1, 1985

By Sato S, Kawaguchi T

The granulation and bed-permeability of sinter raw materials depend on interactions between the properties of various iron ores and water. The properties of individual iron ores are controlled by their particle size distribu- tion and surface characteristics, which can be described by representative particle size and wettability, respectively. Added water may be absorbed, affect granulation or lower bed permeability. These effects were experimentally studied as a function of properties of the iron ores. A mathematical model was developed in order to calculate the granulated particle size and permeability using the known blend of sinter raw materials. The calculated results were in good agreement with the observed values.

Jan 1, 1980

By Coulter L. J

THE method of stope surveying as practised at the Mount Lyell Company's mines has been evolved out of the exigencies created by special conditions. It presents some novel features, and has proved effective for all requirements. All stope measurement work is brought under one complete system, to which office methods are standardized. Before proceeding to deal with the subject a brief description of the physical characteristics of the ore-bodies of each mine and the method of stoping will serve to show, cause ,for departure from ordinary survey practice.NORTH LYELL MINEThe ore-bodies of this mine occur on or near the conglomerate schist contact, and, being probably the result of replacements of both rocks, they rarely present any definite walls. It is usual for the payable material to merge into the respective countryrocks, and the limit of the occurrence is defined rather by assay value than by any distinct natural boundaries. The general configuration of these ore-bodies, therefore, is highly erratic both in horizontal and vertical section, so that, in order to obtain an accurate record of any occurrence, the measurement of the actual contour at short vertical intervals is essential.Stoping is carried out on a modification of the "rill." system, perhaps more properly described as "arched back" or "dome" stoping. Mullock rises are placed in as convenient positions as the erratic configuration of each ore-body will allow, and aroundthese rises the back is kept well arched, both longitudinally and transversely. The larger stopes are divided into arbitrary sections in which ore-breaking and mullocking are carried out in rotation, so that the whole of the excavation is seldom open for measuring at anyone particular time. Stacking or square-setting on the...

Jan 1, 1915

By Irnack C. Do Amaral, Mark C. Malamphy, Desio S. Oddone

Most igneous rocks, and particularly those of the basic type, contain relatively high percentages of magnetite and other iron oxides, which give them moderately high magnetic susceptibilities and make them responsible for an important percentage of the magnetic anomalies observed during the course of geophysical surveys by the magnetic method. The irregular form and high susceptibility of the igneous rocks make them readily polarizable and the position and strength of the magnetic poles formed are not always explicable by theoretical calculations of anomalies due to certain assumed forms in the normal magnetic field of the area under study. During the last four years our field work has permitted us to make detailed observations of anomalies due to igneous rocks in all the states of south Brazil. The form and position of the igneous rock at some places were fairly accurately known, which made it possible to calculate theoretical anomalies and compare them with the observed data. Some of the data we obtained have been published and additional cases are now awaiting publication. In this paper, we will present a few specific cases where the geology is moderately well known and which we believe to be of considerable value as representing typical magnetic anomalies in the south magnetic hemisphere, where the inclination of the magnetic field is very low. Although the vertical intensity is negative in the Southern Hemisphere, we have adopted the convention of plotting increase in intensity (negative) as a positive anomaly; i.e., above the x axis. This convention facilitates comparison with anomalies in the north.

Jan 1, 1940

One of the most important parameters in rock/resin/bolt load transfer mechanism is the surface property of the bolt. Although there are various bolt surface configurations available in the market, very little work is reported on the bolt/resin interface failure mechanism. This paper examines the behaviour of bolt surface roughness under constant normal stiffness conditions which is considered as being a realistic way of evaluating bolt surface roughness. A series of shear tests have been conducted on the flattened bolt surface to study the shear behaviour of bolt/resin interface. Based on the experimental results, a mathematical model has been developed to predict the shear resistance of the bolt/resin interface at various normal stress levels for the bolt types used in the study.

Jan 1, 1999

By Norman Miskelly

Substantial progress has been made over the last ten years in the development of uniform national and international standards covering the definition, estimation and public reporting of mineral resources and mineral reserves. Agreement between the major participating countries has been reached, which include the requirement that a Competent Person prepares and approves publication of mineral resources and reserves. Most national regulatory organizations have accepted the new standards and have included them in the rules that must be followed by mining companies operating under their jurisdiction. These developments are the result of a concerted effort on the part of professional societies, national regulatory agencies, international organizations, and many dedicated individuals. The historical development of these standards is summarized in this paper. Accepted definitions of mineral resources and mineral reserves are discussed, as well as the definition and role of the Competent Person. Additional effort is needed before the international standards are fully understood, accepted and followed by mining companies, regulatory agencies, the investment community and the general public. Steps being taken toward development of a Mineral Reserves International Reporting Code Template (International Template) that will be available for all countries to use in deriving their specific country reporting codes, are outlined

Jan 1, 2003

The non-renewable energy resources of Queensland comprise coal, petroleum (oil and gas), oil shale and uranium. Coal is widely distributed., and has been developed extensively both for export and for use within the State. Proven reserves total 5 390 million tonnes recoverable of coking coal and 5 580 million tonnes recoverable of non-coking; very large resources particularly of non-coking coal are still to be quantified by further drilling. Annual production is of the order of 20 million tonnes of coking coal, principally for export, and 6 million tonnes of non-coking, mainly for power generation within the State. Petroleum resources are meagre in com- parison with those of coal. Initial recover- able reserves of liquids (mainly in the now substantially depleted Moonie Oil Field) totalled only 4.2 million m3. Initial recover- able reserves of gas (mainly in the western Surat and Bowen Basins) totalled 7 800 million m3. Annual production is of the order of 64 thousand m3 of liquids for refining in Bris- bane, and 268 million m3 of gas mainly for production of fertiliser and for industrial and domestic heating, in Brisbane. Prospects are fair for the discovery of additional reserves. Two deposits of oil shale are potentially of economic significance. The Rundle deposit at The Narrows in central Queensland has the

Jan 1, 1979

By Hinrichsen H. D, Rathburn D. R, Stieger W

The present situation in the field of iron ore pelletizing is briefly described with particular view of the Lurgi/Dravo travelling grate process. To meet todays pellet quality requirements with regard to physical and metal- lurgical properties it is often necessary to add basic fluxing materials. It has been de- monstrated that for certain ores, basic addi- tives provide a considerable improvement in fired pellet quality. The production of self- fluxing pellets is becoming increasingly attractive. One Lurgi/Dravo plant is now in operation and another is under construction which were designed for the production of self- fluxing pellets. Self-fluxing pellets may be considered as the primary or exclusive blast furnace burden and the installation of a sinter plant is not necessary if the pellet plant-can handle all in-plant fines. Reference is made to the first pellet plant utilizing iron ore concentrate, in-plant fines and basic flux. The use of solid fuel for pellet indura- tion is discussed because of the increasing prices and possible shortages of heavy oil and natural gas. Since there is a strong tendency to increasing plant capacities, the design fea- tures of travelling grate pelletizing plants for productions up to 6 million tonnes are Discussed.

Jan 1, 1974

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to assist the mining industry in implementing continual improvement in management of major unwanted events so maximising health and safety performance. A comprehensive body of knowledge has been compiled from diverse mining industry experts for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This paper presents an overview of the RISKGATE body of knowledge captured specifically for the management of unwanted events that stem from the handling and use of explosives (drill and blast) within surface coal mining operations. The knowledge presented is divided into a series of initiating events (listed below) within which there are further degrees of classification based on design, operation, and management concerns. Initiating events: ? Loss of control of explosives and associated chemicals in storage on site ? Loss of control of explosives and associated chemicals during transport ? Loss of control of explosives and associated chemicals during manufacture ? Loss of control of explosives and associated chemicals during handling and blast operations ? Loss of control of explosives and associated chemicals during disposal The system guides the user in generating substantive and leading-edge controls to assist in the design, management and reporting of drill and blast operations to meet stringent internal and external requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.

Aug 1, 2013

By Hermann J. A

Over the last few years enormous dapooits of high-grade bauxite have been discovered in Australia, ;_ d an alum .nium smelting industry based on them is rapidly being developed,, This industry requires large amounts of carbon, as about 60 pounds of carbon anodes are consumed for every 100 pounds of aiumin.'.'-n produced. Tie anodes are usually made by mixing finely ground petroleum coke with coal tar or petroleum pitch, forming the mix into shapes under pressure, and baking them at around ?.200¦C0 Petroleum coke is ussd uecause its high density gives good strength and conductav_ty to the finished electrode, and its purity ensures that contamination. of the alumin- ium by extraneous i,iorganic material from tho carbon is low,

Jan 1, 1969

By Ben Benally, Joseph M. Hans

INTRODUCTION The decontamination of the former Shiprock uranium millsite and the interim stabilization of its tailings piles began in March 1974, and ended in June 1978. Personnel monitoring for whole body gamma ray exposure was conducted for selected individuals working at the mill site throughout most of this period. The millsite and exposure conditions are briefly described to develop a basis for interpretation of the exposure data. Millsite The Shiprock uranium millsite is located in the community of Shiprock, New Mexico on a bench overlooking the San Juan River (Figure 1). Both Shiprock and the millsite are located on the Navajo Indian Reservation. About 1.5 million tons of tailings were produced on the millsite during its operation from 1954 to 1963. The tailings were pulped with waste process fluids and water, and discharged to form two tailings piles. The piles (ponds, dams) were formed with earth starter dikes and the dikes were then raised using the separated sand fraction of the tailings. The slime fraction of the tailings were discharged into the diked impoundment. The mill was shut down and partially dismantled before the lease expired in 1973, and the remainder of the mill and tailings reverted back to the Navajo Tribe which was the lessor. Portions of the millsite were then occupied by the Navajo Engineering and Construction Authority (NECA), a tribal enterprise. In addition to its regular activities, NECA established an on-site training school for heavy equipment operators. The trainees principally used the south tailings pile as a practice area and spread the tailings into a 10 hectare row of raffinate ponds located along the southwest side of the millsite. Overall, the training activities inceased the effective area of the tailings piles from 20 to 35 hectares. Another 56 hectares were contaminated with wind and water eroded tailings. Exposure Conditions Persons decontaminating a millsite may be subject to radiation exposures from several sources. Only whole body gamma exposures are discussed in this report. These exposures are arbitrarily divided into three levels: high, intermediate, and low. The levels are related to areas in which the decontamination work was being done and have no connotation concerning imminent hazards. High exposures would result when persons were working with raw tailings, and intermediate exposures would occur when persons were working in the ore storage and mill yards. Low exposures would result from working in areas where surface contamination exists from wind and water erosion. [ ] The millsite and its contaminated environs were divided into major areas to facilitate the decontamination work (Figure 2). Areas A, B, and C are defined as perimeter areas containing surface contamination. Work in these areas was expected to result in low exposures. Areas D, E, and F are the

Jan 1, 1981

By Finlayson E, Hilyard D, Francis G

Papua New Guinea's mainland is dominated by a foreland thrust belt, which can be divided into two zones. The "body" zone is floored by Palaeozoic granites and metamorphics of the Fly Platform (Tasman Orogen). Underlying the "tail" zone is Papuan Plateau, rifted from the Tasman Orogen during Coral Sea spreading, and believed to underlie the Papuan Peninsula and Papuan Islands region (D'Entrecasteaux, Woodlark, Misima, Sudest, and Rossel Islands). Thrusting began in the Miocene and continues today in the crust below the "body" zone. The youngest known thrusted rocks in the "tail" zone are Pliocene in age. Recognition of foreland thrusting has major implications for petroleum prospectivity of the Papuan and North New Guinea Basins, mineral exploration prospectivity, and geological terrane identification in PNG.

Jan 1, 1987

By R. Scheffel, R. Washnock, G. Zarate

"The second survey of global copper leaching operations has been completed, the data published in 1998 has been updated. A survey questionnaire was sent to 40 identified copper leach operations around the world including those leach properties still in operation that responded to the 1998 survey. This paper lists the results of 26 operations that responded to the survey. Selected information from the survey is represented in graphical form. INTRODUCTION Copper leaching was first performed by truck dumping huge monolithic stockpiles of ore and flooding the surface with leach solution or lixiviant with little understanding to the parameters that support optimum recovery of the metal. Heap leaching has evolved into a controlled process whereby a complex low grade ore is stacked in shallow lifts (under 10 m in most cases). The ore is usually crushed and agglomerated, conveyor stacked on an engineered containment system (leach pad) and irrigated in a controlled manner. The lixiviant chemistry is designed to extract the optimum amount of metal from the ore. At first glance, heap leaching appears to be simple in nature. In fact, it is a very complex process. A plethora of technologies such as material handling, environmental control, analytical techniques, solution chemistry, hydrology and many others contribute to the design and operation of a heap leach. Heap leaching requires an inter-disciplinary approach between geologists, mining engineers and metallurgists. Many operational factors affect heap leaching. The process must address climatic factors, flexible operation, quality control before and after leaching, physical characteristics of the ore, geology, mineralogy, reagent consumption, solution application rate and methods (wobblers or emitters), particle size, and favorable conditions for bacterial growth and survival. Predicting, troubleshooting, and optimization of leach recovery is a significant challenge when considering the number of variables involved and their interactions The survey updates many of these key operating parameters to the current state of the art. It should provide the reader an excellent benchmarking summary of these factors on a site-by-site basis."

Jan 1, 2016

By Fiedler VA, Threadingham GM, Leckenby DF, Clarkson CJ

The Utah Development Company Research and Development Laboratory has embarked upon a programme of optimisation of the company's coal preparation plants. This goal is being accomplished in a three-fold manner - use of pilot plant equipment for optimisation and modelling of the various unit operations, evaluation or development of on-stream ash analysis for process control, and evaluation or development of alternative processes. In each of these areas, digital data acquisition- and at a later stage, process control feedback, is being extensively utilised, based largely upon the use of the HP85 and HP9915 desktop computers. A variety of input/output configurations such as HPIB, BCD, GPIO are used, and at times supplemented by microprocessors such as the Intel 80/05 to assist in data transfer. This paper will discuss a number of specific projects, especially in relation to the manner in which the variables are monitored, and the data later retrieved and analysed.

Jan 1, 1983

By Beim Jorge, Piscsalko George

"Verifying the quality of cast-in-place foundation applications, particularly those cast under slurry, is of course important, due to its great dependency on the methodology employed and on the practices of the site personnel. Due to the techniques used to install these elements, it is usually not possible to inspect the hole prior to grout or concrete placement, but there are several Non Destructive Test (NDT) methods available to assess the integrity of the completed foundation elements. This paper will compare several NDT methods with the Thermal Integrity Profiling (TIP) method for verifying the integrity in Continuous Flight Auger (CFA) piles and Bored Piles. The Thermal Integrity Profiling method will be described and some examples will be presented where TIP testing was used to confirm the structural integrity of CFA piles and Bored Piles.IntroductionThere are several Non Destructive Test (NDT) methods available for integrity testing of foundation elements. Each of those methods has advantages and disadvantages (White et al, 2008). Some methods test the integrity based on the reflections of a stress-wave generated by low or high-strain impact, while others require tubes to be installed prior to concrete pouring, and test the integrity between those tubes, or within a small proximity of them. The former methods (especially the low-strain) are faster and more cost-effective, but are not able to detect the quadrant where the damage is located. The latter methods are able to determine the quadrant, but do not test the region outside of the reinforcing cage, that is, they are not able to determine the concrete cover. The Thermal Integrity Profiling (TIP) NDT method overcomes the limitations of these other NDT methods.Overview of Shaft Integrity MethodsUntil now, the most widely used methods to test the integrity of Bored and CFA piles were the low-strain pile integrity testing and the cross-hole ultra-sonic testing. The low-strain method for integrity testing (PIT) involves attaching an accelerometer usually to the pile top (using a putty or wax) and striking the pile surface with a handheld hammer, which causes a compressive wave to enter the pile. This wave is totally reflected when it reaches the end of the pile or a major defect, and is partially reflected when it encounters any change in crosssection, or a change in the resistance or density of the pile material. These reflections arrive at the top at a time determined by the distance and wave speed, and causes a noticeable change in the signal detected by the accelerometer. The acceleration signal is normally converted to velocity by simple integration, and sometimes the force applied by the hammer is also measured. The velocity (and force) signals can be processed by the pulse-echo method (in the time domain) or by the transient response method (in the frequency domain)."

Jan 1, 2015

By M. W. Bartley, Hugh M. Roberts

SUBSTANTIAL deposits of Bessemer hematite have been found recently by drilling beneath Steep Rock Lake, Ontario, which is situated in the northern part of the Lake Superior Region. It will be practicable to divert the waters flowing into this lake and develop open pits on the upper part of two large ore bodies by damming off and pumping out the water in the part of the lake in which they occur. Ultimately, the bulk of the ore will be mined by underground methods. Owing to the generally massive nature of the rocks in the area, no underground flows of major consequence are anticipated after diversion of the lake. The Steep Rock deposits are attributed in origin to hydrothermal replacement. They were formed, for the most part, along an unconformable, brecciated contact between the Steep Rock limestone and an overlying younger volcanic series. The replacing solutions came in as igneous after-effects, following upon the intrusion of basic igneous rocks that invaded the hanging-wall volcanics. It is believed that this took place in a geological period roughly equivalent to late Middle Huronian, which was the period when the most extensive iron-bearing rocks of the Lake Superior Region were formed. Comparison is made with other deep-seated iron-ore bodies in the Lake Superior Region, the origins of which are ascribed in the discussion to hydrothermal replacement.

Jan 1, 1943

By Rohan Stevens, Katsuhiro Kameyama, Osamu Iwata, Jinming Liao

In densely populated cities such as Hong Kong, where unoccupied space is becoming more valuable as the population grows, city planners are more often looking to underground space to meet the increasing need for transportation and services. Given the dense population of people, amenities and high-rise buildings above or near such underground space, it is essential to minimise any disturbance and potential damage during construction. Hence, the excavation of hard rock to develop such underground space can be highly restricted, expensive and time consuming. This is the case for many of the tunnels currently being excavated by drill and blast directly underneath Hong Kong’s busiest business districts and most popular residential areas.

Jan 1, 2013

The microstructures exhibited by ilmenite in its association with other oxide minerals have been the subject of a number of papers, the most comprehensive of which is that by Ramdohr. The following observations in some degree extend his conclusions. They are based upon a study of about sixty specimens of "massive" ilmenite and titaniferous ores from a number of wIdely 'scattered Australian localities. Specimens of this character proved much rarer than was expected. The collection was gathered together through the generous aid of the University Geological Departments, Geological Surveys, and Natural History Museums of the several States of the Commonwealth, all of which contributed such specimens of local origin, as they possessed. Special thanks are due to Dr. E. S. Simpson, of Western Australia, who made available several highly interesting specimens, together with his...

Jan 1, 1938