Search Documents

By Kjell Lidin, Christer Nordström

INTRODUCTION LKAB produces iron ore in several mines in northern Sweden, and has been doing so for nearly 100 years. Total production to date is 600 million tonnes of finished products of various kinds (pellets, lump ore, fines). Close to 400 million tonnes have been produced by sublevel caving. This method has been the company's standard method for more than 20 years. A review of the development of equipment over the past 15 years and an outlook up to about 1990 leads to the following general re- flections concerning probable trends. Trends for all equipment are increasing precision and stricter environmental requirements will necessitate cabs, remote control etc to an increasing extent. Conventional sublevel caving can be broken down into the following unit operations: 1. Planning incl prospecting drilling. 2. Horizontal drilling. 3. Fan drilling. 4. Charging and blasting. 5. Loading and haulage at sublevels. 6. Ore drawing in chutes. 7. Rock reinforcement. 8. Production service. This lecture will deal in brief with each of these unit operations and the trends we are experiencing for them. A number of slides illustrating equipment

Jan 1, 1981

By Holmes R. J, Miles J. G

An on-stream shale detector has been developed that is suitable for use on conveyor belts carrying iron ore of up to 200 mm particle size. The shale is distinguished from high-grade iron ore by means of the substantially greater total natural gamma-ray activity (400-3000 keV) of the shale, which is due to the presence of uranium (214Bi), thorium (208TI) and potassium (40K). Other gangue materials, sueh as highly siliceous cherts and jaspilites, escape detection because of their low activity. A dynamic trial of the shale detector at Mt Whaleback, using a large-volume (100 × 100 400 mm long) "Polyscin" Nal(TI) gamma-ray detector, demonstrated that as little as 20 tonne of ore on a conveyor belt (equivalent to partial truckloads of ore) can readily be monitored for shale content.

Jan 1, 1981

By Irvin G. Burough

Andros Analyzers Incorporated has designed and built two prototype continuous methane monitors capable of being mounted on a mining machine'. These instruments were designed for in-mine safety use. The monitors incorporated an NDIR optical/electronic analyzer design in which the response to the sample gas (methane in air) was achieved by synchronous detection and measurement of the amplitude oscillations of the trasmitted energy from an infrared source caused by the pressure modulation of the sample gas within the optical cell. Zero and span stability were to be achieved by the amplitude modulating of the infra-red source and using detected signal to correct for optical/electronic system variation. This design effort was to simplify and reduce the cost of the major components while eliminating the need for daily calibration. This report is the final report on this effort.

Jan 1, 1981

By Pinczewski WV, Nowak LP, Tanzil WBU, Jenkins DR, McCarthy MJ

An experimental and theoretical study has been made of the drainage behaviour of two-dimensional packed beds drained from an outlet in the sidewall of the bed in order to identify the fundamental me- chanisms involved. Under these conditions a grad- ient develops in the air-liquid interface in the direction of flow with the interface tilting towards the outlet. This results in a significant volume of liquid being retained in the packing on completion of draining when the interface first reaches the bed outlet. Residual liquid volume and the shape of the air-liquid interface as a function of time were det- ermined experimentally in a two-dimensional packed bed where the packing consisted of glass spheres ranging in size from 0.6 to 10 mm dia. and the bed was drained at superficial liquid velocities rang- ing from 0.007 to 0.32cm/s. The test liquids used were water, glycerine/water solutions and kerosene resulting in a viscosity range of 1 to 10 mPa.s and a surface tension range of 0.0243 to 0.072 N/m. Assuming laminar flow within the bed, a compu- tational model was developed to predict both the liquid residual ratio and the temporal evolution of the drainage profile within the bed. The computed results were in good agreement with the experimental data over the entire range of conditions invest- igated. the computational model was used to estimate the relative importance of the effects of changes in hearth conditions on residual slag volume for typ- ical blast furnace operating conditions. On the basis of the computed results it is concluded that coke quality is a major parameter affecting hearth drainage performance.

Jan 1, 1981

By Graham A. Karklin

"The Echo Bay Mines silver property is located 875 air miles north of Edmonton, Alberta. The mine is on the east shore of Great Bear Lake at Port Radium which is twenty six miles south of the artic circle, in the North West Territories.HISTORYThe area was first surveyed by J. Mackintosh Bell of the Geological Survey of Canada in the early nineteen hundreds. In May 1930, Gilbert LaBine staked claims at Port Radium called ""Cobalt"" and ""Cobalt I"". What he had discovered was an extremely rich vein of pitch-blend. These claims were the birth of mining in this area. The first ore shipment of pitch-blend was hand-picked and flown out of Port Radium in 1931. LaBine's discovery of pitch-blend became of world-wide importance with the outbreak of World War II. In 1939 the splitting of the uranium atom brought this area into world focus. It is generally believed that it was ore from this area that was used in the production of the devastating bombs which were dropped on Japan.It was at Port Radium that the leaching process for uranium extraction was pioneered. The resultant methods have been modified and adopted for use around the world. The mine was originally owned by Eldorado Gold Mines Limited. Echo Bay Mines leased the property in 1964, subsequently purchased it, and have been producing silver and copper every since."

Jan 1, 1981

By Harry Wolf

The chemistry of the element uranium enables industry to employ either an acid or alkaline carbonate leach solution for most uranium ores. Either method my be used for conventional, in-situ, or heap leaching. Uranium recovery in the leaching process depends both on the solubility of the uranium minerals and, on the access of the leach reagent to them. The uranium leaching rate is proportional to the liberated mineral surface area and the chemical reactions involved in the dissolution step. The dissolution of U(VI) and the oxidation of u(IV) to U(VI) are the basic chemical reactions in the leaching process. The active surface area is a function of the effective porosity and the particle size of the ore (1). Ore pieces, with a high porosity and high permeability, may provide a large active surface area even in coarser fractions. This type of ore might be suitable for heap or in-situ leaching techniques. Nonporous and impervious ores are usually more amenable to conventional milling where the active mineral surface is exposed by grinding the ore down to the liberation size of the mineral.

Jan 1, 1981

By A. Block-Bolten

Copper concentrates from northern Peru contain large amounts of arsenic and antimony in the form of sulfosalts like enargite, tennantite and tetrahedrite. These impurities affect up to 30% of Peruvian copper production. Under the sponsorship of the Instituto Geologico Minero y Metalurgico in Lima a project to separate copper from arsenic without pollution of the environment is being carried out at the National University of Trujillo in Peru. The U.N.T. process is unique in the respect of using .low melting salts as solvents, and sulfides of metals with high cation potential as destructors of the complex sulfosalt molecules. Laboratory scale experiments have given encouraging results but interesting and difficult problems developed on scale-up. The process is pyro-hydrometal-lurgical and under certain circumstances its economics are promising.

Jan 1, 1981

By W. L. Cooley

Electrical accidents occurring in coal mines from 1975 through 1979 were categorized and analyzed. The data was searched for common electrical hazards, common activities on the part of those injured, and common negligent or careless behavior. The most common electrical hazard was abnormal arcs or sparks, the most common injured activity was handling energized trailing cables, and the most common careless behavior was failure to de-energize circuits before working on them. The accident data was combined with mine production statistics to form a normalized electrical accident rate. It was found that some mines have consistently more lost workdays per man-hour worked than do other mines. Bureau of Mines electrical safety research contract expenditures were reviewed to judge whether the research effort was directed to those areas which are related to the most accidents. In some cases it was not. A method was devised and utilized to estimate the relative cost to the mining industry to implement certain safety measures developed through Bureau research, and also to estimate the potential safety benefits. Some safety changes are recommended, others are not. MSHA regulations were reviewed for effectiveness in preventing electrical accidents, and suggestions were made for discontinuing, clarifying, or otherwise modifying the regulations.

Jan 1, 1981

By Jerry Bennett

This report describes the results of a survey of current blast area guarding procedures at surface and underground metal/nonmetal mines. It features five case histories (two surface and three underground mines) of blast guarding methods considered to represent the best systems in use in the U.S. Mining Industry. Elements of an effective blast guarding system are presented along with recommendations for improvements in current blast guarding practices. Industrial and military surveillance and detection technology was reviewed to determine if parallel technology exists for immediate application to blasting site security. While it is concluded that immediate transfer of industrial security technology will be limited, a number of recommendations are advanced for new research to adapt some of that technology for application to the mining environment. Two research areas considered to offer the most potential for improved blast guarding are presented. They are, computerized personnel tracking and blast area intrusion detection using infrared, microwave or E-field type detection systems.

Jan 1, 1981

By Redman P. G, McMahon B. K

A simple technique for evaluating the field stress ratio is presented, based on the results of extensometer or convergence tape measure- ments taken in an advancing tunnel. This tech- nique also yields a value for the rock mass modulus, provided Poisson's Ratio is assumed. The results of two case studies are presented illustrating the effectiveness of the method.

Jan 1, 1981

By Isobe K, Muchi I, Hsieh YS

Theoretical and experimental studies have been made-to clarify the physical and chemical behavior of the tuyere combustion zone of blast furnace. Gas streamlines around this zone were visualized by the use of the two-dimensional equip- ment. Close agreement between the observed stream- lines and the calculated ones is found. The three- dimensional experimental studies have revealed that there exists a so-called dry zone in the neighbor- hood of the raceway and the trickling liquid be- haves approximately like a continuum. A kinetic model is develdped to describe the behavior of coke combustion in the tuyere zone. The model is based on the reaction kinetics, the differential balances of heat and mass, and the mechanics of gas flows. Regarding-the-axial distribution of gas composition in the tuyere zone, good agreement is obtained be- tween the model prediction and the data observed in a working furnace by the other investigators. Cal- culated results-show that the maximum consumption of coke occurs at the intermediate region of the raceway. For the blowing of oxygen-enriched or high -humidity blast, the position at which the maximum consumption of coke occurs is shifted toward the tuyere nose. Similar effect is found when the par- ticle diameter of coke in the tuyere zone is de- creased. The solid flow pattern around the tuyere combustion zone was visualized by the use of the two-dimensional equipment in which the sublimation of dry ice particles in front of the tuyere was

Jan 1, 1981

By Elmer E. Buban

A lightweight compressed oxygen rescue breathing apparatus (RBA) for rescue and recovery missions has been developed by Mine Safety Appliances Company under contract to the Bureau of Mines. The apparatus is a positive pressure, closed circuit system of 4 hours duration. The weight of the complete apparatus, including an optional cooler, is slightly over 30 pounds. Weight reduction over currently available RBAs is achieved through the use of lithium hydroxide for scrubbing C02 in place of conventional chemicals and the use of a composite glass fiber/ aluminum shell cylinder for oxygen storage in place of steel cylinders. Positive pressure is maintained in the breathing circuit at all times by applying a constant spring force to the breathing bag. The harness has been designed to reduce the work of the wearer by redistributing the weight of the apparatus to the wearer's hips.

Jan 1, 1981

By W. J. Guay

Carbonaceous gold ores containing gold dispersed in sulfides are refractory to cyanidation because: (1 ) the carbonaceous materials adsorb gold during cyanidation; (2) a portion of the gold s so finely dispersed in the sulfide mineral lattice as to preclude contact with cyanide solution; and (3) a portion of the gold is chemically combined with carbonaceous material. Techniques which have been used to treat these ores are: (1) roasting or chemical oxidation to decompose sulfide and carbonaceous materials; (2) flotation to reject carbon; (3) the use of kerosene or other reagents to passivate the adsorptive carbon compounds; (4) carbon or resin in pulp; (5) flotation of a bulk concentrate which is treated by one of the above methods; and (6) the use of chelating agents which have a stronger affinity for gold than the activated carbon in the ore.

Jan 1, 1981

By Noel N. Moebs

Bureau of Mines studies of mine roof fall problem in the Pocahontas No. 3 Coalbed of southern West Virgania and southwestern Virginia have established that type and sequence of rock are significant factors in roof competence. The poorest conditions occur where the immediate roof consists of slump structures and slickensided rock. The best conditions occur where the roof consists of a sequence that coarsens upward from shale to massive sandy shale. A small manual of color photographs of rock types was devised to aid in identifying drill cores. Proper identifications should enhance the prediction of areas of potential roof problems in advance of mining.

Jan 1, 1981

By William Laird

The predominent method of coal mining in the United States for years has been room-and-pillar mining. The reason for this has been the advantages of room-and- pillar method which is a relatively flexible system and its capital investment. The room-and-pillar method permits some selectivity in mining, especially where gas wells, faults and possible coal quality may be a factor. The mobility of continuous and conventional mining equipment used to develop entries may also be used for retreat mining of rooms and pillars. Longwall mining of coal takes place along a long straight face, or wall, blocked out between two butt or panel entries. The long faces or walls are normally projected in lengths of 61 to 183 m (200 to 600 ft) in this country. The longwall method of mining had its beginning in the United States during the 1800's. During that period, pack wall and wood posts were used for roof support. The longwall face was mined by miners using picks to undercut the coal. To keep the coal face from turning over, short wood posts called sprags were set in a slant position as the coal face was undercut to the depth of two to three feet. When the under-cutting cycle was completed, the sprags were removed to permit the coal to fall from the roof pressure. The longwall mining of coal did not take a firm hold during the 18009s, and room-and-pillar prevailed. In the early 19009s, steel jacks were introduced, and along with it, the modified caving theory. In March of 1950, a retreat longwall mining system, utilizing a plow, manually operated props, wood cribs and chock releases, was installed in one of Eastern Associated Coal Corp.'s mines.

Jan 1, 1981

By L. C. Stone, J. C. Parr, T. N. Anderson, D. Metcalf

An increase in the importance of low-grade materials as sources of gold and silver has led to the need for improved analytical methods on leach solutions, ores and various effluents, residues, and in-process streams. These are required by plant operators as guides to process control and for accounting pldrposes. Atomic absorption spectrophotometry (AAS) and AAS preceded by pre- concentration have been applied successfully to resolve many such problems. However, AAS is no panacea and imprecision or loss of accuracy can result if adequate precautions are not taken to prevent losses and eliminate interferences. The recent methods are discussed together with methods for overcoming difficulties. Comparisons with more classical analytical techniques are also given.

Jan 1, 1981

By B. Gillenwater

This report describes the results of investigations into four specific areas related to trolley wire power distribution systems in coal mines. These are: 1. Partially insulated (shielded) trolley wire 2. High-speed insulator fault detectors 3. Dual-wire trolley systems 4. Insulator failure indicators. Prototype devices or designs were developed in each area. In addition, a brief survey was made in an attempt to assess the Future of mine trolley systems, and data was collected and reviewed in an attempt to analyze the nature of trolley wire related accidents. Other options for decreasing the risks associated with trolley systems that arose .during the study are briefly described in appendices. These include insulating equipment and miners from return and/or energized conductors and use of a segmented trolley wire with local control of current delivering capability.

Jan 1, 1981

By G. H. K. Pearse

Long range transport of pollutants, particularly of sulphur dioxide and the associated acidic precipitation, has received much attention in the press and in international discussion during the last few years. Studies revealing increasing acidity of lakes and the dying out of fish populations over broad regions of the eastern half of North America have created alarm. In this paper, I will not attempt a description of the acid rain phenomenon. For this r recommend the balanced treatment of the subject by Gene Likens et al (1979) in Scientific Americana For my purposes I accept that the problem is serious and direct my attention to exploring a solution. Ultimately, the key lies in the answer to the question; "What do we do with the enormous tonnages of pollution abatement byproducts, chiefly sulphur compounds, that would arise from pollution control?"' Little thought has been given to this most limiting factor to environmental clean-up. This is symptomatic of a basic flaw in the [philosphy] that under-ins environmental policy. Although this paper is to propose a solution to the abatement byproduct problem, the basic flaw - the firmly entrenched, universally adopted, 'polluter pays [philosphy] as it is currently [understood] - needs some comment.

Jan 1, 1981

By Dyson N. F

Mixed cobalt-nickel sulphides precipitated from ammoniacal process liquors derived from nickel sulphide concentrates, mattes, and reduced nickeliferous laterites have been characterized.The mixed sulphides are prone to oxidation on standing and are rapidly leached under relatively mild conditions. The kinetics of the leaching reactions are controlled principally by temperature and oxygen partial pressure. Although the samples have different CO:Ni ratios and have undergone varying degrees of oxidation, there is little difference in their leaching behaviour. The results suggest that a single plant would be able to process mixed sulphides of varying composition. Any copper and zinc present in the mixed sulphides as impurities also go into solution and must be removed prior to recovery of the cobalt and nickel in metallic form.

Jan 1, 1981

By Ralph B. S

Bacterial leaching of low grade quartz felspar porphyry copper ore was studied in large-scale laboratory percolation leaching columns.Limitations in the release of soluble copper showed up before fifty per cent recovery, due to occluding precipitates of iron oxides and hydroxides. Precipitates were removed by increasing the acidity of irrigation feed four-fold with respect to sulphuric acid. However, irrigation at low pH (pH 1.5) inhibited copper leaching. Resumption of bacterial leaching at pH2 was achieved by introducing a period of non-irrigation. The results suggest a 'direct' attack by bacteria on the chalcopyrite substrate rather than an 'indirect' ferric-leach mechanism.

Jan 1, 1981