Search Documents

By Pinter R

Several major routes connecting Northern and Southern Europe or Asia run through Austria. These highways have to surmount the alpine range which traverses Austria from west to east. In order to ensure safe driving conditions even in winter, tunnels, at times quite long ones, are necessary. Austria now has tunnels totalling 160 km in length. These tunnels are either already in use or just about completed. The Plabutsch tunnel near Graz will be one of the longest tunnels in the world: approximately 10 kilometers in length. It will be put into operation in the summer of 1987. Before construction could begin, soil and rock conditions had to be investigated by means of a test tunnel. Afterwards, excavation was begun to the full 100 m' cross section. The new Austrian tunnelling method with conventional blasting was used for the major part of the tunnel. It was necessary to have such a large tunnel cross section because a fully transverse ventilation system is installed for environmental reasons. In order to avoid air pollution from the tunnel, exhaust fumes are not allowed to escape from the tunnel portals but from two shafts, each with a diameter of 8.5 m. In this way, exhaust fumes must rise 90 meters or 240 meters before they reach the open air and will thus not affect the city. The ventilation system influences the size of the excavation, and especially the size of the ventilation caverns and the air shafts. All these factors directly influence construction and maintenance costs, and an economical optimisation leads to the appropriate dimensions for the excavation.

Jan 1, 1987

By Thomas M. Barczak

The intent of this paper is to make mine operators and engineers aware of parameters which affect the loading behavior of passive roof support systems. The strength of a passive roof support element alone is not a meaningful measure of support performance. Passive roof support elements and the surrounding strata act as a system, responding to changes in the physical mine environment due to the extraction of coal and associated redistribution of stresses. The load- ing of a passive roof support element is a function of the stiffness of the roof support structure; a stiffer structure will react a higher load to a converging mine roof than will a more flexible structure. If the stiffness if the support structure is not properly designed, excessive loading will result due to the displacement of the mine roof, causing premature failure of the support. Ideally, the yield strength of a passive support needs to be no greater than that required to support the dead weight of the immediate mine roof, providing the post yield characteristics of the support are compatible with the irresistible convergence of the overburden strata and the support system continues to provide this resistance after reaching its yield load. Idealized design considerations for passive roof support systems in terms load-displacement characteristics discussed. The stiffness and yield characteristics of wood concrete cribbing, as determined controlled tests in the Bureau's Roof Simulator, are compared preliminary recommendations passive roof support utilization also provided.

Jan 1, 1987

By Christie GB, Mainwaring DE, Leong YK

High solids brown coal slurries have been prepared with concentrations approaching those achieved with bituminous black coals. The high inherent water content and macroporosity of Victorian brown coals have been reduced in a controlled manner by chemical and mechanical means. The hydrophobicity of the coal surface has been increased sufficiently to reduce the tendency for swelling and water uptake. This together with densification has allowed the solids content to be progressively improved from 25% solids with raw coal to 65% solids with modified coals. Both raw brown coal and modified brown coal suspensions show shear thinning behaviour resulting in lower viscosities at higher flow rates. All coal suspensions displayed a yield stress once sufficient solids concentration was achieved. This yield stress can be used in the prevention of solids settling. Under simple shear mixing the network structure that provides the yield stress quickly breaks down to a low viscosity fluid with reduced yield stress and a pumpable consistency. The time necessary for structural recovery is in the order of days permitting shut-down and start-up of fuel delivery systems.

Jan 1, 1987

By John H. Perry

Strata III is a full-spectrum roof control system which provides the mine operator the ability to upgrade his roof control in place. The procedure is easily adaptable with current roof bolting techniques. To use the system, the operator starts by installing a special hollow core mechanically anchored roof belt during the roof bolting cycle. This bolt can be upgraded to a fully grouted tensioned rebar bolt by injecting StrataGee G-300, a special polyurethane grout, around the bolt through an injection port in the roof plate. This same bolt can then be used to inject RokLok binders for roof consolidation by pumping the binders through the core of the bolt. This concept in roof control was developed to provide the mine operator a flexible way to maintain roof control in areas which deteriorate over time, or must be kept open for long periods of time. Possible locations of use would be: longwall set-up rooms, recovery rooms, headgates, intersections, and belt entries.

Jan 1, 1987

This paper describes a proposal to reopen the Sylvia gold mine for underground exploration and development for an initial production of 10 000 tpa. A combination of trackless mining equipment and railtrack would be utilised for development with ore extraction being carried out by undercut and fill methods. The use of the smallest LHD units for mucking, and rail track for the main haulage together with airleg drilling will form the basis for development and stoping. The proposal has been subjected to an environmental impact assessment report to evaluate the impacts of the proposal on the natural and social environment in the area.

Jan 1, 1987

By Mallett CW, Hammond RL

Geological maps of the Pacific Rim recently published by the Circum-Pacific Council for Energy and Mineral Resources have provided a useful perspective from which to view modern plate interaction and the evolution of modern fold belts. An important lesson from any study of modern plate interaction is that of the normality of change. The chaotic is more usual than the simple. Present day convergent margins with mixed characteristics are measures of this chaos. Indeed, the character of less than one third of the present length of the Pacific Rim can be ascribed to conventional models of plate interaction. Another lesson is that of the great mobility of oceanic crust. Enormous areas of the Pacific may not be represented in future fold belts developed at convergent boundaries unless normal consumption processes are disrupted, and even then only by linear zones a few kilometres wide. The axes of divergent boundaries creating Pacific Ocean crust have been equally mobile, with new spreading sites taking over from older sites through time. Divergent boundaries, whether active or inactive, consist of oceanic crust, and may be wholly consumed at collision sites with convergent boundaries. Their only potential contributions to fold belt evolution are transforms and magmatic activity. It is this transform component that can provide us with a mechanism to explain the apparent contradiction of both compressional and extensional features occurring together in a developing fold belt. Reconstructions for the SW Pacific are used to demonstrate that the fold belts under construction during the last 4% (Jurassic- Recent) of geologic time have involved interaction between convergent, divergent, and transform boundaries. In the last 15% of earth history (Late Proterozoic-Recent), many enigmatic features of the geologic landscape in Eastern

Jan 1, 1987

Gold was first discovered in the Shotover by Thomas Arthur in 1862. He left his job as a shearer and soon there were up to 3000 miners working over the length of the river. Some parts were extremely rich and a few early miners recovered as much as 300 ounces in a day. From these early days of hand working the operations progressed through to hydraulic elevating once water races and pipes were installed after the Skippers road was completed about 1890. The riverbed was worked in paddocks with .the gravel being sluiced to a central suction which elevated the material over a sluice box. Use of this system continued intermittently through until 1977 when Joe Schieb retired û the last of the hydraulic miners. Many bucket ladder dredges worked on the lower Shotover near Big Beach where the Sew Hoy family recovered a lot of gold. Just after 1900, at least three worked further upstream, one on the beach where Shotover Jet now operates and one further up below the Moonlight. All the sections for this were transported in over the Moonlight Track and the boiler, steam engine and bucket ladder are still sitting at the edge of the river. up near Maori Point a dredge operated from Dredge Slip upstream. Records are poor on these dredges but they all suffered from the frequent floods and large boulders which damaged the bucket line. The last dredging attempt was about 1930 when a suction dredge was constructed on Maori Beach. This failed as seems to be normal for most suction dredging ventures. The river can drop to very low levels in the middle of a dry summer, and in winter when the water is tied up in the mountains as ice and snow. During 1863 when heavy rain melted snow in the high country, the river rose 35 feet overnight and drowned many miners camped on the banks. The ever present risk of flooding dominates the method of working and plant design.

Jan 1, 1987

By J. E. Gebhardt, D. W. Fuerstenau

The use of small quantities of polyacrylic acid (PAA) was found to significantly improve the flotation of fine-sized hematite particles at pH 4.1 and 0.001 M NaCl with sodium dodecykulfonate (SDS). Low polymer dosages before collector addition aid flotation by forming flocs of primary particles, but excess polymer results in low flotation yields due to surface saturation by the hydrophilic polymer. Contact angles, measured on a hematite disk, substantiate the hydrophilic nature of an adsorbed polymer film. Pre-adsorbed PAA reduces the amount of SDS adsorbed on the hematite particles, but the flotation of hematite flocs occurs, even at reduced amounts of adsorbed SDS, and is not depressed until PAA dosages in excess of the saturation value are used. Separation of a hematite-quartz mixture can be achieved by SDS flotation of PAA,-flocculated hematite. Maximum selectivity results with the addition of small quantities of PAA, while excess polymer is detrimental to the recovery of hematite. Consecutive flotation states on a single feed yield a higher grade hematite product at some expense to the overall recovery.

Jan 1, 1987

By Ronald F. Balazik

The introduction of "high-tech" materials such as new polymer composites presents significant competitive challenges and opportunities in conventional mineral markets. Moreover, rapid advances in materials science are critical to the resolution of important economic and strategic issues, including national competitiveness and import dependence. This Bureau of Mines study examines the displacement of conventional nonfuel mineral materials by certain new materials, specifically advanced plastics and ceramics. Analyses of substitution by plastics are conducted for five major U.S. industrial sectors: motor vehicle manufacturing, aerospace applications, building and construction, packaging, and heavy machinery production. Based on interviews with more than 60 scientists, executives, and other professionals engaged in materials development and sales, forecasts of substitution by plastics during the 1990's are made for aluminum, steel, and glass. In addition to these forecasts, study findings identify key factors that will influence the emergence of advanced materials in the next decade.

Jan 1, 1987

By experience we know about the natural event of ocean-tides. In geophysics we say that the earth-tides phenomenon is the elastico-viscous response of the earth's body to the attraction potential of moon and sun. By the fact that the tides on the planet take place in a regular periodic frequency, due to the earth rotation of 24 houres for one cycle, the rotation of the moon in about 28 days around the earth and finally to the rotation of the earth-moon combination around the sun in 365 days this phenomenon is a very important one in geophysics. The exact calculation of the acting forces is possible and the comparison of the earth's body response to these forces as well.

Jan 1, 1987

By J. Mitchell Linne

In 1986 at the request of Bureau of Land Management, the U.S. Bureau of Mines studied 23,225 acres of the 27,980-acre Jordan Craters Wilderness Study Area (OR-003-128) in order to evaluate its identified mineral resources. The study area is located in Malheur County, OR, about 20 miles northwest from Jordan Valley. No mining activity has been recorded within the study area, and no metallic or industrial mineral resources were identified. Small isolated occurrences of decorative quality stone were identified. However, none of these occurrences constitute a resource. Although the study area is underlain by relatively young volcanic rocks, the area has no known geothermal energy resource.

Jan 1, 1987

By Moeller T

The Bottle Creek mine, when opened next month, will consist of three open cuts, Emu, VB and Boags, feeding ore to a central mill. The open cuts cover a strike length of 4.5 kilometres which forms part of a linear structure, which can be traced geochemically for 26.0 kilometres. With the exception of a few small gossanous outcrops at Emu, the deposits are completely covered with insitu laterite and alluvial overburden. Since its discovery in 1984, the deposit has been subjected to three major reverse circulation (RC) drilling programmes which have successively closed up the drill spacing on the main mineralized zone to 25m horizontally and less than 25m vertically. All resource calculations have been based primarily on samples of RC drill cuttings from these programmes. Ore reserve calculations have been completed after each drilling phase. They began with a simple polygonal technique, progressed through two sectional half-distance calculations and are now being completed with a 3-D geostatistical technique. Because of the style of mineralization, Norgold personnel paid particular attention to assessing the variability of the mineralization by using repeat samples, repeat analysis and diamond drill vs RC comparisons. In addition, close attention has been paid to obtaining an accurate estimate of the global SG of the ore bodies. Particular care has been taken to obtain complete drill intersections of the orebody and to maximize wet sample recoveries. Extensive re-sampling and re-analysis of samples has confirmed that Bottle Creek is unusual for an oxidized gold deposit in that all the gold appears to be very fine grained, and evenly distributed within the mineralized zone.

Jan 1, 1987

By David C. Lager

While not a new construction technique "top/down" construction is seeing increased use in high rise building construction. Using diaphragm wall, drilled shaft and mining construction techniques, top/down construction enables construction of both the below grade basements and high rise structure simultaneously. To date the top/down method has been used on at least four major building projects in the United States. This paper will review the economic, engineering, construction and schedule issues associated with top/down technology on two projects -Olympia Centre, Chicago, and One Westwood, Los Angeles. Top/Down construction is currently under consideration on several additional projects in the United States.

Jan 1, 1987

By Hoffmann CF

Thermal conditions at depths of several k.i'-.r.,etres in hydrothermal systems are a major (actor controlling gold transport into the epithermal environment. Understanding of the coupling of thermal, metal and ligand (HZZ S) sources in the root zones of hydrothermal systems therefore becomes important for the application of tectonic and igneous petrochem- ical studies to regional scale precious metal exploration. The evaluation of favourable conditions in this source zone and application to explor- ation rests on a detailed knowledge of the gases, H2S, CO2 hydrocarbons and other trace components preserved in fluid inclusions. Recent developments in analytical techniques now permit examination of these components and the recognition of complex hydrocarbons in rluid inclusions from epithermal and other lydrothermal systems appears promising for ieoosit-source correlation.

Jan 1, 1987

By K. Nagata, T. Kawashima, S. Tejima

The expanding volume of maritime coal transportation is intensifying the problems concerning large vessel service, port construction, trans-shipment, and environmental control. The major problem is the shipment of coal. Customary methods for bulk transfer must be improved and new systems developed. Slurry unloading has a key role in the new systems. This report reviews progress in slurry transportation research that has been done in Japan since the 1960s, when large-scale experiments for domestic transportation were done. Experiments on the effects of vibration on the slurry cargo and on reslurrying are focused on.

Jan 1, 1987

By J. E. Geier

This Bureau of Mines report reviews hypotheses for the mechanism by which water jets reduce the specific energy of cutting for drag bits. Several of these hypotheses are shown to be inconsistent with published evidence and new observations. The notion of a limiting cutting speed, above which water jets would be incapable of rendering assistance, is shown to be improbable. The hypothesis that seems most plausible is that specific energy reductions are mainly due to the erosion of crushed materials from in front of the bit. This hypothesis leads to a prediction that, for a given rock type and jet-bit configuration at a constant depth of cut, the reduction in bit forces should be a function of dM/dx, the jet energy spent per unit length of cut. This dependence upon dW/dx is shown to be consistent with other workers? results.

Jan 1, 1987

By Wightman D, Hoyle M. W H, Peters W. S

The Radio Hill nickel-copper deposit is located 30 km south of Karratha. It is a new discovery in an area where similar mineralization had been previously discovered at Mt. Scholl and Ruth Well. Radio Hill is the first massive Ni-Cu sulphide deposit of economic significance to have been located in the Western Pilbara.Preliminary studies indicate that the sulphide mineralization occurs within gabbros, pyroxenites and peridotites of a basic igneous cumulate layered sequence. Primary sulphides have been subsequently remobilized and concentrated as stringer and massive mineralization. This is tentatively attributed to the intrusion of a further gabbroic body.The deposit appears to be of the gabbroic association type with a Ni:Cu ratio varying from 1:4 in the outer parts of the mineralized envelope to 1:0.9 towards the central zones. In drill core observations, chalcopyrite surrounding pyrrhotite was noted in many instances. Drilling has so far delineated a body developed over a strike length of 600 m and a horizontal width of up to 25 m. The mineralization plunges 20° to the southwest with a southerly dip varying from 75° in the west to about 20° - 30° in the east.The deposit is a leaf-shaped ore zone, plunging southwest from a vertical depth of 17 m in the north to 300 m in the south. The massive sulphides occur as lensoid masses within this zone. A geological resource of up to 2.5 million tonnes at 1.5 per cent Ni and l.4 per cent Cu is indicated.The predominant sulphides are pyrrhotite, chalcopyrite and pentlandite, with significant cobalt, platinum group metals and gold. Tellurides of Pd, Bi and Pb were detected by scanning electron microprobe within the pyrrhotite and other trace metals include Zn and native tin. Massive magnetite is sometimes associated with the massive pyrrhotite intersections.A test on one composite massive sulphide sample showed that pyrrhotite is present mainly as the non-magnetic hexagonal variety and only 10 per cent is present as magnetic monoclinic pyrrhotite.The deposit has no surface expression and its identification was based mainly Oil drilling targets generated by geophysical methods. No secondary minerals have been observed in association with the primary sulphides, even though the deposit is only 17 m below surface in the northern part.

Jan 1, 1987

By G. K. Jorgenson, S. H. Chung

"IntroductionThe SABREX Blast Modelling Program was developed jointly by the companies of the ICI Explosives Group, of which C-I-L Inc. is a member. SABREX (Scientific Approach to Breaking Rock with Explosives) is a modular computer program which incorporates new technology with a number of tested programs that have been in use world wide.SABREX predicts the performance of blasts in terms of (I) fragment size and distribution; (2) muckpile profile and face velocity; (3) grade fracture; (4) collar breakage; (5) a rupture envelope which depicts crack penetration behind and beneath blastholes; and (6) a complete cost analysis including explosives, drilling and accessory costs. The predicted blast results are displayed as dynamic colour graphics and in tabular form.SABREX uses data on the detailed geometry of the drilled and loaded pattern, detonation characteristics of the explosives and the dynamic properties of the rock to generate blast predictions. SABREX blasting calculations take into account the effects that shock and quasi-static pressures exert on the rock around the blastholes. While physical effects occur very rapidly in rock blasting, it is possible to view and model the sequence of events as discrete sections.The program can be run on a microcomputer and is currently operated by C-I-L technical service staff in Canada for the use of drilling and blasting operators.Figure I is a diagram representing the modules of the program and associated technology that is used to complement the program.Any, or all, of the modules may be used in a particular study or blast optimization. Because the BOBCAT module of the SABREX program has been described in previous papers(7.8.9), this discussion will concentrate on the newer modules: CRACK, HEAVE, RUPTURE ENVELOPE and to a limited extent, KUZ-RAM, which present a more detailed picture of the blasting process.Each of these modules is discussed in terms of the information they offer the operator in analyzing the blast. Specific examples of recent usage in Canadian mining situations are included to illustrate the ability of the model to produce practical results that can assist in optimizing actual blasting operations or solving problems that do exist."

Jan 1, 1987

Attempts to rationalise the geological environment of nickel sulphide deposits associated with Archaean ultrabasic rocks has produced much speculation as to the origin of the sulphides and the relative importance of geochemical, mineralogical, textural and structural characteristics of the host rocks. From an economic viewpoint the object of such work is to establish geological criteria which can be used as an exploration guide. Exploration procedure for nickel sulphide mineralisation of the 'Kambalda type' (Hudson, 1972), which occurs at or near the basal contact of Archaean ultramafic flow units and lenses consisted of geological mapping, surface prospecting with soil sampling and rock geochemistry.

Jan 1, 1987

To George Orwell the year of 1984 was the inspiration for a book. To most New Zealanders it was the year that the fourth Labour Government was elected to power. It was also the year that the review of mining legislation commenced. While Orwell's book and the election of Labour are clearly events of some historic note, one could be excused for classifying the review of minerals legislation somewhat differently in terms of its present achievements! Since the review began it has led a tortuous path through a rapidly evolving policy environment to a point three years hence where no major policies have been determined.

Jan 1, 1987