Search Documents

By Julian M. Avery

In its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all ecorlomy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss call be successfully attacked by increasing the over-all pressure; i.e., the "top prcssure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity. In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

By Maurice L. Pinel, Thomas Wright, Thomas T. Read

The erroneous, but until recently widely prevalent, belief that iron castings were first made in Europe in the fourteenth century has been adequately refuted in a number of earlier papers;1, ll, l² but except for an unpublished metallographic study by the late William Campbell, and a phosphorus analysis by T. A. Wright of the metal of the Han dynasty cast-iron stove described by Laufer,2 nothing was known of either the chemical composition or the metallographic structure of the metal of any ancient iron casting, although data on castings of recent manufacture are abundantly available. The metal of the stove, which had been buried in a grave for at least 15 centuries, was so corroded that it seemed inadvisable to publish the results on it until morc and better specimens from other ancient castings could be obtained. During a journey through China, extending from Peking in the north to Canton in the south and Cheng-tu, Ssu-chuan, in the west, in the late summer and autumn of 1936, one of us (T. T. Read) was fortunate enough to obtain, and bring home for study, nine castings, all more than 1000 years old, of which the date of manufacture is precisely known because of inscriptions cast in them, another that lacks a dated inscription, but of which the date, as explained below, can be otherwise established, and a specimen from the largest iron casting ever made," which is also dated. The period covered by this suite of specimens extends from 502 to 1093 A.D. In addition, a sample was obtained from a casting of date unknown, but which was certainly cast before 1000 A.D. and possibly as early as the third century A.D. A detailed description of these specimens is as follows: I. 502 A.D. A pair [right and left) of recumbent lions (Fig. 1). Base 7¼ by 113/8 in., height over-all 5½in, weight 26 Ib. each. The tranblation of the inscription on the base is: "Made on the twenty-fourth day of the seventh month of the third pear of Ching Ming of Great Wei" (Sept. 11, 502 A.D.).

Jan 1, 1938

By B. S. Norris, Charles R. Austin

The stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals' has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.* It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. $ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, wlletller deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of deformation. With this information, a study of the rates of work-

Jan 1, 1938

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

Jan 1, 1938

By Harry A. Roe

The power drag scrapers and the slackline cableway excavator have been called "long-range excavators." Broadly, their field of usefulness is restricted to work in which their long range of action permits them to operate economically, and which other, possibly more conventional, excavating units cannot do. Both of these machines dig or lift material and transport it to a remote dumping point. They combine these two functions in a single machine, nearly always in a single straight-line motion. The purpose of this paper is to examine the important features that distinguish the machines in this group from each other, as well as from other groups. The Machines The "power drag scraper" is a long-range excavating machine that employs a bottomless drag scraper operated back and forth between digging and dumping points by two haulage cables. The typical arrangement is that of Fig. 1. This is the "slusher" of the underground mine, as well as the "dragline scraper" of the sand and gravel industry, and other open-pit mining operations.

Jan 1, 1938

By Joseph C. Buchen

In principle, productiorl of salt from sea water is a simple operation. The sun and wind cause evaporation of sea water trapped in ponds, and what is left is principally salt. Commercial production, however, requires consideration of many factors. First is a high consistent annual rate of evaporation, as well as large areas of suitable low-lying ground close to economical shipping facilities. The south end of San Francisco Bay has these requisites. Large ponds are built, by using clamshell dredges to build up levees to a height of approximately 3 ft. on ground usually lower than sea level, so that the water may be taken in through tide gates without pumping. Ponds are divided into extremely large concentrating ponds and smeller crystallizing ponds. Approximately ten times more area is required for concentrating than for crystallizing. The concentrating ponds are irregular in shape and size but the crystallizing ponds are rectangular and fairly regular in size, to aid in harvesting. The ocean water is taken into the first of a series of concentrating ponds and gradually moved forward from pond to pond as it increase:: in density, reaehing the crystallizing area as a saturated brine. This brine is pumped into the crystallizer at the beginning of the net evaporating season, usually in May, and further evaporation causes its sodium chloride content to deposit on the bottoms of the ponds. The brine must be drawn off and a fresh supply added from time to time to prevent other undesirable salts from depositing with the sodium chloride. Harvesting usually begins near the end of August and now is accomplished almost entirely by mechanical means. After harvesting, the salt is stored in large sbockpiles until required for shipping or refining. The greatest amount is used for industrial purposes and is shipped without any processing other than screening, but all salt for domestic use produced by the Leslie Salt Co. is refined by the racuum process, giving a produet consistently testing over 09.9 per cent sodium chloride.

Jan 1, 1938

By Henry Mulryan

The largest and purest known deposit of diatomite is being actively mined and processed 3 1/2 miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Nlanville Products Corporation. The workings cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoe, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1938

By Richard W. Smith

Kyanite, long known to occur in Georgia, did not excite coimmercial interest until about 1930. Investigation1 revealed two main types of deposits: (1) separate kyanite crystals embedded in mica schist; and (2) crystal aggregates of kyanite associated with quartz in small and very irregular veins. The second kind at first sight appeared to be the best source of supply. Large boulders or dornicks of kyanite with more or less quartz were found on the surface at many places throughout the Piedmont and Highland sections of the state, but prospecting failed to disclose a sizable vein. These dornicks seem to be a surface accumulation from small veins or lens-shaped masses not more than one or two feet thick, and with a horizontal extent of not more than a few feet. 'rile larger surface accumulation of kyanite dornicks, where not too badly stained by iron oxide, may prove to be marketable, but it is extremely doubtful whether a vein large enough to mine will ever be found. In 1932 deposits of the kyanite-mica schist were known to occur in two places northwest of Clarkesville, in Habersharn County. In 1934, at the request of and in cooperation with the Georgia Geological Survey, the United States Geological Survey made a thorough investigation2 of the deposits and found that the two known areas of kyanite-mica schist in Habershain County were but a part of an unsymmetrical, U-shaped belt (Fig. 1) with a western limb extending into Rabun County and somewhat longer than the eastern limb. The total length of the belt is about 30 miles. The width of outcrop ranges from 100 ft. to 1/4 mile or more. Deposits of kyanite-mica schist of very doubtful commercial importance were found in several other counties. Only the deposits of this kyanitc-mica schist belt in Habersham and Rabun counties will bc discussed in this paper. Geology The kyanite-mica schist of Habersham and Rabun counties occurs near the northern cdge of the Piedmont Upland in metamorphic rocks of pre-Cambrian age3. These rocks probably were deposited as sedimentary

Jan 1, 1938

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

By Philip Bucky

THE term "longwall mining" is best known to coal men, although modifications of the method are continually being used in other fields. Longwall mining is of interest today because it makes for greater mecha-nization and better supervision at the working face, and therefore lower production costs and increased safety. It is an approach to the factory system of production, the high efficiency of which as compared to that in mines is well known. There is available an accumulation of experience regarding this work but coordination of experience is lacking and this series of experiments was undertaken to help serve this purpose. Model experiments were used for reasons of safety, cost and time, and because it has been previously shown1,2,3 that a scalar model built of the same material as the prototype will behave in a manner similar to that of the prototype, with time effects the same, if the effective weight of the model is increased in the same proportion as its linear dimensions are decreased. This is accomplished by substituting a centrifugal for the gravitational field; i.e., placing the model in a centrifuge and controlling the strength of the centrifugal field by varying the rate of rotation. Many factors affect the behavior of the geologic material overlying a bed, therefore results and conclusions contained in this paper apply only to the conditions presented herein.

Jan 1, 1938

[ ]

Jan 1, 1938

By Herbert Johnson

DURING the past 10 or 12 years very little information has been made generally available concerning the commercial possibilities of separating materials by means of static electricity; and yet during that same period important improvements have been made in various branches of the science of electricity, which, when taken together, and applied to electro-static separation, have resulted in important improvements in that art as well. For example, much improvement has been made in high-voltage electrical equipment such as full-wave vacuum-tube rectification and improved mechanical rectification. Great strides have likewise been made in the development of insulators for high-voltage work, not only in the materials used but also in the design of the insulators themselves. Again, in another field, the development of air-conditioning equipment has improved the technique of controlling the surface condition, through drying or humidifying, of the various materials that are passed through the electrostatic separator. In many authoritative publications and textbooks, the electrostatic separation process is declared to require a balance far too sensitive for general commercial application. For example, one publication1 in the past has referred to an unfavorable effect on the process caused by varying atmospheric conditions such as humidity. Some2 have even gone so far as to state that sunlight and shadows may seriously affect the separating efficiency of the process. Such statements may have been true in the early development of the art, when the source of static elec-tricity was derived from a friction disk machine, such as the Wimshurst. The Blake Mosher equipment and the work of Huff in applying motor-generator sets, transformers and mechanical rectification overcame much of this kind of objection to the commercial application of the elec-trostatic separating process.

Jan 1, 1938

By C. B. Foraker

THE Magma mine, of the Magma Copper Co., at Superior, Pinal County, Arizona, is 68 miles east of Phoenix and 21 miles west of Miami, Arizona, on highway U. S. 180. TEMPERATURES AND UNDERGROUND WATERS Surface Temperatures.-The average surface dry-bulb temperature at Superior is 72.4°; wet-bulb, 57.4°; with an indicated relative humidity of 38 per cent. The average yearly rainfall from 1921 to 1936, inclusive, was 18.74 in. The maximum condition of the atmosphere is in June, July and August, and the minimum is in January and February. The surface temperatures, of course, influence the temperatures of the down-cast shafts; however, the variation between winter and summer causes a difference of only 2° to 3° in the stopes and working places that are not close to the intake shafts. Average atmospheric conditions are shown in Fig. 1. Rock Temperatures.-Rock temperatures on the deeper levels of tile mine are as follows: LEVEL DEGREES LEVEL DEGREES 2000 109 3200 127 2250 112.5 3400 130 2550 116 3600 134 2800 120 3800 137 3000 124 4000 140 There appears to be no difference in rock temperature for any particu-lar horizon of the various formations or in the vein. Water encountered is always the same temperature as the rock from which it flows, and for this reason it is thought that the water is heated by the rock; not the rock by the water. The country rock apparently has been heated by the various intrusions, perhaps the vein itself, and has not yet had time to cool off. The geothermal gradient (Fig. 2) as indicated by the rock tem-peratures given above is 1 1/2 ° per 100 feet.

Jan 1, 1938

By L. C. IlsLey

The increasing use of Diesel engines for operating equipment on trunk-line railroads and for power-plant units has stimulated interest in the use of Diesel engines for other lines of work, among which is the possibility of substituting Diesel locomotives for trolley locomotives for mines. The possibility of developing Diesel locomotives for duty in American mines is not as remote as it might seem, particularly in view of the fact that locomotives of this type are already used in considerable numbers in European mines. A study of Diesel locomotives in Europe is contained in Report of Investigations 3320, Diesel Mine Locomotives - Development and Use in European Coal Mines, by George S. Rice and F. E. Harris.

Jan 1, 1938

[ ]

Jan 1, 1938

By S. H. Lorain

This paper is a preliminary report on recent lode gold mining activity, operating conditions, and mining and milling methods at properties in production in September 1936 in the gold belt of northeastern Oregon. A few inactive properties are described also. Districts, inactive in 1936, that have been important producers at some time in the past are mentioned briefly. This is one of a series of similar papers describing western mining districts. The past production record of the gold mines of northeastern Oregon entitles the region to be ranked as one of the important gold-mining regions of the United States. Although comparatively inactive for many years, lode mining in the region has recently undergone a marked revival.

Jan 1, 1938

By Henry Mulryan

The largest and purest known deposit of diatomite is being actively mined and processed 3 1/2 miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Nlanville Products Corporation. The workings cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoe, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1938

Power Plant. The power for the metallurgical operations is supplied by the company's own power plant, which is centrally situated. Power is also supplied to Metal Manufactures Ltd. and Australian Fertilizers Ltd., both being adjacently situated to this company'sworks.The power supplied is direct current, 250 volts, and is obtained from direct-current generators coupled to turbines and to Belliss & Morcom triple expansion engines.The steam supply is obtained from Babcock & Wilcox water tubular boilers, the fuel used being drawn from the South Coast coal mines.Transport. - The works are connected by standard broad gauge railway to both the jetties and the Government railway. Two steam and three electric locomotives are employed in this service.In addition to its own requirements, transport is provided to Metal Manufactures Ltd. and Australian Fertilizers Ltd.The various operating departments are connected by a 2-ft. gauge railway operated by Jeffrey electric locomotives.Ore Storage and Sample Mill - These departments are connected by broad gauge line to the Government railway and jetties. All material which is railed or shipped to the works from the various centres is weighed, sampled and placed in the ore store, or outside gantries, before being treated.Since the whole of the material received is either purchased or treated on a toll charge, great care is necessary in the weighing and sampling of all the receipts.Assay Oflice--The assay office is divided into several laboratories, where analyses of the various purchased materials and works samples are carried out.

Jan 1, 1938

By G. S. Scott

[The Duretiu of Kinen, as :) pr<r"Yof its :;encr:rL propan clealini: with the causes, behavior, n.ncl tor-trol of o1:t1?;.?cite-mine fires, hns investic:&apos;lte3 I varionr. Te:.nr, for Je tec tin:: iccj.r)ic:~ t he;, tint; :,:.zqdergro-.:rid and of <~e termining the trend of the hen tir..: once -I i&apos;i re j 7 knnm tr, he nrcsc~t.]

Jan 1, 1938