Search Documents

By Kenneth M. Smith

"The kaolin deposits of Aiken County, South Carolina (fig. 1), have been worked continuously since 1852. It has been long known that the deposits contain a high percentage of alumina and that large reserves exist. These facts led to the early selection of this area for examination in the search by the Bureau of Mines for high-alumina clays. An exploratory program was started by the Bureau, and drilling was carried on from June 27, 1942, to October 31, 1942.The kaolin-bearing district occupies an area approximately 25 miles long and 11 miles wide, running northeast, with its center at Aiken, S. C. (fig. 1). Within this district, a triangular area bounded by Horse Creek, Silver Bluff Road, and Hamburg Road was roughly prospected by boring 43 machine and 12 hand holes. As a result of the data obtained, a final smaller area was chosen for more systematic prospecting. This area is bounded by Pine Log, Tewkesbury, Silver Bluff, and Craig Sawmill Roads and covers about 4,000 acres.Mineral exploration agreements covering 11,272 acres were signed by 35 property owners, and 11,956 feet was drilled in 200 holes on these properties.The Bureau of Mines exploration work in the district has indicated 19,514,000 short tons of kaolin, of which approximately 10,000,000 tons would average over 35 percent alumina.The tonnages and grades of kaolin developed by this exploration are tabulated below.All grades of this kaolin average approximately 2 percent Fe203 and 1.5 percent Ti02.This project was under the general supervision of J. R. Thoenen, supervising engineer, Non-Metals Mining Section of the Mining Division, Bureau of Mines, until July 1942. The -project was then under the general supervision of E. J. Lintner and later Rowe McCrae, consecutively district engineers for Georgia, South Carolina, and Florida. The final report was prepared, under the general supervision of V..J. Lynch, chief, Raleigh Branch, Mining Division, by William A. Beck from the original report by the author.Acknowledgment is made for the wholehearted cooperation and assistance given to the Bureau of Mines by the various operating companies in the district. Particular thanks are due Theodore Henderson, general manager; North American Clay Co., Wilbur Driver, general manager, and Howard Driver, assistant general manager, The Huber Clay Co.; H. W. Smith, president, The South Carolina Clay Co.; and J. Richard Parker, president, J. R. Parker Clay Co., all of Bath S. C.; J. B. Howard, Jr., superintendent/ the Immaculate Kaolin Co., Langley, S. C.; Richard Jones, president, National Kaolin Co., and William Winans, president, The Southern Clay Co., both of Aiken, S. C.; and W. S. Burkalter, Warrensville, S. C.Acknowledgment is also due the Metallurgical Division for analytical determinations and to James J. Page of the Federal Geological Survey for his aid in mapping and logging the holes.The first known use of kaolin from this district was by the Bath Pottery Co., which began mining an outcrop in Horse Creek Valley, near Bath, in 1852.. In 1867, R. McNamee, of New York City, acquired this pit and continued mining. This first mine is still known as the McNamee, and from its operation grew the present kaolin industry of South Carolina."

Dec 1, 1949

By William A. Beck

"In 1912 bauxite was discovered in the Andersonville district, which lies in the 28th and 29th land districts of Georgia and comprises parts of Sumter, Macon, and Schley Counties. Mining was begun in May 1914 by the Republic Mining & Manufacturing Co. Considerable ore has been produced in this region since that time by individual interests and by the American Cyanamid & Chemical Corp., which acquired the property formerly owned by the Republic Co.The area was examined in the fall of 1941 by representatives of the Bureau of Mines and the Geological Survey, after which a prospecting program was begun by the Bureau. Drilling was started on December 26, 1941, and continued until November 18, 1943. A total of 1,192 holes was drilled in the district, and 3,679 samples were taken and analyzed.Mineral exploration agreements were signed by 146 property owners covering 42,128 acres. Holes were drilled on 121 of these properties, which have a total area of 38,778 acres.Drilling under this project disclosed several new deposits, of which four have been completely delimited. Previous prospecting in this area by mining companies did not find bauxite, as it lies under heavy overburden. Work by the Bureau indicates 14,412,000 long tons of ore containing 30 percent or more alumina. The total tonnage is divided as follows:Georgia State Highway Routes 26 and 4-9 traverse the district. The Central of Georgia Railroad passes through the center of the entire district (see fig. 1).The project was initiated by J. R. Thoenen, supervising engineer, Non-metals Mining Section, Mining Division, Bureau of Mines. It was under his general supervision until July 1942, after which it was under the general supervision of E. J. Lintner and Rowe McCrae, district engineers for Georgia, South Carolina, and Flordia, respectively.John C. Feeley, Jr., was project engineer from December 1941 to April 1942. Other engineers who assisted in the work on the project are R. E. Babcock, T. M. Romslo, Don M. Coulter, and Walter T. Lewiecki.Acknowledgment is due the metallurgical staffs at College Park, Md., and Tuscaloosa, Ala., for analyses of samples and beneficiation tests.Acknowledgment is also expressed to Alfred D. Zapp, M. W. Harris, Elmer Kneedler,and Parke D. Snavely, of the United States Geological Survey, for their aid, data, and maps.Bauxite was discovered in the Andersonville district in 1912 on lot 187 of the 28th land district, in Sumter County. This lot is situated about 1.5 miles west of the Flint River, on the south slope of the valley of Sweetwater Creek. Mining was started in May 1914 by the Republic Mining & Manufacturing Co. This and adjacent properties were acquired in 1930 by the American Cyanamid & Chemical Corp., which has been operating there since."

Dec 1, 1949

By John H. Soule

"Although known since 1902, the Capitan iron deposits have not been mined, mainly because of the low grade of the ore. Only a small amount of exploratory work has been done since the discovery. C. H. Johnson, district engineer of the Bureau of Mines in New Mexico in 1942-45, visited the property; as a result, preliminary sampling of the property was done in 1943.3/ Owing to the results of this preliminary work, an extensive development program by wagon drilling was planned and executed early in 1944.4/ Equipment available at that time was limited in the depths that could be reached; and, as geologic studies indicated the possibility that other limestone beds below the surface might have been replaced by iron minerals, a supplementary development program by churn drilling to reach greater depths was prosecuted in late 1947 and early 1948, with the author as project engineer.The following sections note the location and accessibility of the deposits and mention the physical features, climate, labor and living conditions. Property and ownership are outlined, the history and production of the property stated briefly, and the ore deposits are described. The work done by the Bureau of Mines is explained and supported with maps, sections, and assay logs.From March 1, 1944, to June 1, 1944, 179 wagon-drill holes totaling 3,490 feet and 4 test pits totaling 75 feet were completed, and from November 1947 to February 1948 seven churn-drill holes totaling 2,488 feet were drilled and sampled. Metallurgical tests are summarized and referenced.With respect to this report, special acknowledgment is due to J. H. Hedges, chief, Tuscon, Ariz., Branch, Mining Division, and to W. R. Storms, engineer in-charge of the Silver City, N. Mex., field office. Acknowledgment also is due to J. Bruce Clemmer, chief, Tuscon Branch, Metallurgical Division, for analyses done in the last phase of this project, and to Dr. Vincent Kelley of the Federal Geological Survey for his cooperation during this work.The Capitan iron deposits are in secs. 10, 11, 13, 14, and 15, T. 8 S., R. 14 E., central Lincoln County, N. Mex., as shown on figures 1 and 2. The only known large deposit upon which the Bureau did development work lies around the common corner of secs. 10, 11, 14, and 15, as shown in figures 2 and 3, and just southwest of and in the foothills of the Capitan Mountains. This range of mountains trends east and west. The elevation of the highest peak is 10,205 feet.The deposits are reached by traveling on State Highway 48 from Capitan north for 4 miles, to a point just inside the Lincoln National Forest fence and thence due east over a poor dirt road for 1.2 miles. Just over a small wooden bridge, the left-fork is taken, and the poor road is followed to the deposits, a further distance of 1.1 miles (see fig. 1). This road follows the fence to and through the Davis ranch. All the roads from Capitan to the deposits are dirt roads but are impassable only for short periods during and after heavy rain or snow."

Aug 1, 1949

By Frank E. Cash

"INTRODUCTION The producing iron-ore ranges in the Lake Superior district are the Marquette and Menominee in Michigan, the Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. The accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year owing to stockpiling underground ore during the winter, or nonshipping, season but closely approximate each other over a period of years. This information circular supplements, combines, and continues the data contained in Information Circulars 7321 3/ and 7410 4/, including statistics for 1946 and 1947.Whereas the title ""Accident Experience"" is used for uniformity and logical indexing throughout this report, ""injury"" will be used as a general term to apply to disabilities of all degrees.During the 8-year period 1940 to 1947, inclusive, 619,054,023 long tons of iron ore was shipped from the Lake Superior district. 5/ Michigan and Wisconsin shipped 117,828,939 tons, or 19.03 percent of the total, and employed approximately 9,260 men. Minnesota shipped 501,225,084 tons, or 80.97 percent of the total, and employed an approximate annual average of 12,260 men. The tons produced and shipped per man employed in Minnesota is much greater than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jun 1, 1949

By Allen D. Look, Alan A. Sharp

"INTRODUCTION The bottoming of the United Verde sulfide pipe has shortened the expected life of the United Verde mine to a matter of a few years. First located in 1876, this Arizona mine has had a long period of activity, having reached a peak production in 1929 of over 71,000 trans of copper. Through these many years of successful operation, a safety program has evolved in keeping with the proficiency developed in mining the ore body. It is the purpose of this paper to record the safety practices in effect at this mine so that others may have the benefit of lessons ,learned through experience 'and years of work toward an improved accident record.ACKNOWLEDGEMENTSAcknowledgment 'is 'made to ,the Phelps Dodge Corp. for its cooperation in making available data contained in this paper, and to C. E. Mills, general superintendent; W. W. Little, mine superintendent; John Riordan, employment agent; and G. S. Leisk, safety engineer, for their helpful suggestions and information furnished.GENERAL INFORMATIONThe United Verde copper mine is situated just west of Jerome, Ariz., at an altitude of approximately 5,500 feet. Purchased by the Phelps Dodge Corp. in 1935, the mine employs approximately 500 men - 385 underground and 115 on the surface."

May 1, 1949

By Reed. Donald F.

"Deposits of gray hematite occur in two districts in Talladega County, Ala., the Emauhee-Tallasochatchee and Weewoka, both in the vicinity of Winterboro, 50 miles east of Birmingham.The deposits were investigated by the Bureau of Mines in 1943 and 1944. Approximately 13,000 feet of diamond drilling was done and 6,000 linear feet of trenches excavated and sampled.A total of 13,000,000 tons of ore averaging 36 percent iron was indicated in all areas.A detailed discussion of each property investigated, drill logs, and sampling results are given in this report.In the work done in the Talladega County iron investigation, special acknowledgement is due to Paul M. Tyler, formerly regional engineer, Eastern Region, and Richard W. Smith, formerly district engineer, for aid and direction of the project; also to J. B. Clemmor, metallurgist, for diligent research work in the Southern Experiment station laboratory. All were members of the Bureau of Mines Staff.The project was conducted in cooperation with the Federal Geological Survey, whose field work was in charge of T.G. Andrews assisted by Brewster Baldwin. The able and valuable assistance of Andrews and Baldwin aided greatly in accomplishing the project.The areas investigated by the Bureau of Mines were in two districts: The Emauhee-Tallaseehatchee district, between Sylacauga and Sycamoer (marked B on fig. 1) and the Weeworka district, between Winterboro and Sycamore (marked A on fig. 1)."

Mar 1, 1949

By D. R. Torgoson, Th. G. Sahama

"This paper contains some new thermodynamic data for silicates in the series Mg2SiO4-Fe2siO4 and MgSiO3-FeSiO3 and gives the results of a thermodynamic attack on the problems of stability end parageneses.. Although some data are lacking satisfactory agreement with mineralogical and petrological observations is indicated.The use of thermodynamic methods in mineralogy and petrology has been rather limited, because accurate thermal data, especially for the more complicated and more important rock-forming minerals, have been too scanty to permit any systematic application to problems in those fields. It is, nevertheless, a fascinating task to investigate to what extent the mode of occurrence and the stability relations of the minerals and mineral parageneses, as revealed by petrological and mineralogical observations, agree with predictions of thermodynamics. At the present stage of development calorimetric data are needed for most of the abundant silicate minerals.Measurement of the heats of solution in hydrofluoric acid of minerals in the series Mg2SiO4-Fe2SiO4 and MgSiO3-FeSiO3 affords a ready means of obtaining their heats of formation from the oxides. Combination of such data with entropy and heat-capacity values gives a means of obtaining free energies of formation from the oxides, which, in turn, are connected di¬rectly with stability and paragenoses.The two silicates of magnesium, Mg2SiO4 and MgSi03, occur as rock-forming constituents as forsterite and clinoenstatite or enstatite. The orthosilicate (forsterite) forms a series of isomorphic mixtures with ferrous-orthosilicate (fayalite). The continuity of this series, suggested by petrological observations, has boon proved experimentally by Bowon and Shairer.4/ The present work shows that those minerals constitute a series of perfect solid solutions - that is, a series of solid solutions for which heats of formation from the individual pure silicates, Mg2Si04 and Fe2SiO4, aro negligibly small.The metasilicates of magnesium and iron also form an isomorphic series. However, this series differs from the forstorito-fayalite series in the fact that the most iron-rich mixtures, between about En10Fs90 and pure Fs, appear to be unstable with respect to the paragenesis iron-rich olivine plus quartz. The supposed instability of pure FeSiO3 as a crystalline compound, at least at high and at moderate temperatures, is remarkable, as no crystal struc¬tural reason for such instability is apparent. The present work indicates, also, that these minerals form a perfect series of solid solutions and throws additional light on the instability question.In the following, the samples used in this investigation will be described. For each of the natural olivines and orthopyroxenes, with the exception of sample L, a chemical analysis was made of the purified and actually used fraction. All the analytical work was carried cut by Oleg v. Knorring, and the specific gravity determinations, by moans of a pycnomctcr, by Oiva Joensuu, both of the University of Helsinki, Finland. The determinations of the optical properties were made by Mrs. Toini Mikkola, of the Geological Survey of Finland."

Feb 1, 1949

By Gerald A. Muson, Fremont F. Clarke

"INTRODUCTION The use of scrap mica as an industrial raw material has grown rapidly during the past two decades. Demands by various industries for ground mica for use in the roofing, paint, rubber, plastics, and wallpaper trades as well as for less extensive uses in insulation, oil-well drilling, welding, pipeline enamel, decorative material, and for other purposes exceed present (1947) supplies.A small proportion of the raw material used comes from the Black Hills of South Dakota, where casual recovery has been practiced in the exploitation of pegnatite deposits for more valuable minerals. The annual production of scrap mica in the Black Hills for the years 1939 to 1946 is shown in figure 19. 4/Although small, this production of scrap mica materially augments the incomes of numerous operators.Volume production of mica would offer attractive opportunities for obtaining steady and more economical supplies of the rare minerals as byproducts. Appreciable supplies of beryl, lithia minerals, sheet mica, tantalite-columbite, and cassiterite could accrue. Furthermore, a stable scrap-mica production would complement the production of quality feldspar, for which the Black Hills pegmatites are noted, and would help balance the economy of pegmatite mineral production.Mechanical methods of separation are requisite to production of enough scrap mica to be generally profitable. Various phases of the characteristics end treatment of mica have been investigated by the Bureau of Mines. A bibliography of these reports is appended.In 1945 the Bureau of Mines conducted pilot-plant tests to recover scrap mica by selective screening of crushed pegmatite. More recently the problem has boon studied in the Pegmatite Research Laboratory to aid in developing technological methods by which scrap mica may be separated from crushed pegmatite."

Feb 1, 1949

By Donald F. Reed

Deposits of gray hematite occur in two districts in Talladega County, Ala., the Emauhee-Tallasechatch and Weewoka, both in the; vicinity of Wintorboro, 50 miles east of Birmingham. The deposits were investigated by the Bureau of Mines in 1945 and 1944. Approximately 15,000 feet of diamond drilling was done and 6,000 linear feet of trenches excavated and sampled.

Jan 1, 1949

By W. E. Stiles

A method is presented for predicting the performance of water flooding operations in depleted, or nearly depleted, petroleum reservoirs. The method makes use of permeability variations and the vertical distribution of productive capacity. From these two parameters can be calculated the produced water cut versus the oil recovery. Derivations of the mathematical analogy is shown and sample calculations and curves of prediction are presented. Comparison is made of the predicted and actual performance of a typical 5-spot in an Illinois water flood. INTRODUCTION The use of water as a flooding medium in both depleted and "flush" oil reservoirs is gaining greater recognition and acceptance. Many of the shallower fields, depleted by primary production, have been and are being subjected to water injection in order to obtain some part of the large volume of oil remaining after primary production. Some of the earlier water flood installation proved highly discouraging and the value of water flooding was often questioned. Many of these earlier floods were haphazardly selected and developed as little was known of the physical characteristics and contents of the producing formations. The prior evaluation of the flood performance was impossible. During the past decade the development of the required reservoir engineering tools-—core analysis, reservoir fluid analysis, electric logs, fluid flow formulae, etc.—has allowed the engineer to construct and apply the methods which are presently being used to evaluate the economic and mechanical susceptibility of a reservoir to flooding. This discussion will present a method for taking into account the effect of permeability variations in predicting the performance of water floods in depleted reservoirs. PERMEABILITY AND CAPACITY DISTRIBUTION It is generally agreed by most investigators that in a single phase system fluid will flow in a porous and permeable medium in proportion to the permeability of the medium. Producing formations are usually highly irregular in permeability, both vertically and horizontally. However, zones of higher or lower permeability are often found to exhibit lateral continuity. Thus, while structurally comparable stringers in adjacent wells may differ several fold in permeability values, they usually bear resemblance as being part of a general continuous higher or lower permeability section. It is generally agreed that where such stratification of permeability exists, injected water sweeps first the zones of higher permeability, and it is in these zones that "break-through" first occurs in the producing well. It is a basic assurnption of the presently described method that penetration of a water front follows the individual permeability variations as if such variations were continuous from input to producing well. This is admittedly not rigorously true, but can be justified as making possible a simplifying mathematical approach to an otherwise extremely complicated three dimensional flow problem. As a basis for study of the lateral flow of fluids in formations of irregular permeability, the irregularities may be conveniently represented by a permeability distribution curve and a capacity distribution curve. In obtaining these curves, the permeability values, regardless of their structural position in the formation, are rearranged in order of decreasing permeability. If these permeability values so arranged are plotted against the cumulative thickness, a permeability distribu- tion curve is obtained. This curve may then be likened to a "smoothed" permeability profile of the formation. In making comparison between different distribution curves it is convenient to state the permeabilities in terms of the ratio of the actual permeability values to the average permeability of the formation. These ratios termed "dimensionless permeabilities", are used in this paper rather than the permeabilities in terms of millidarcys. The capacity distribution curve is a lot of the cumulative capacity (starting with the highest permeabilities) versus the cumulative thickness. The capacity and thickness are given as fractions of the total capacity and thickness. Mathematically, the capacity distribution is the intergration of the permeability distribution curve. In practice it is convenient to first obtain the capacity distribution curve and derive from it a smoothed dimen-sionaless permeability curve. The method of obtaining the capacity distribution curve is illustrated in the successive column of Table 1, in which capacity and thickness are derived as fractions of their respective totals. If only a small number of permeability values are available, it is generally desirable to smooth the resultant curve. This has been done to give the capacity distribution curve shown in Figure 1. The differentiation of the capacity distribution curve to obtain the permeability distribution curve is shown in Table 2. Here, the capacity values are read from the smoothed curve at intervals of cumulative thickness, and the increments of capacity are divided by the increments of thickness to obtain the dimensionless permeability, K. Due to this stepwise procedure of calculation these premeability values must be plotted at the midpoints of the successive increments of thickness. The curve so obtained from these data is shown in Figure 1. The total area under the K' curve is equal to unity.

Jan 1, 1949

By H. G. Doll

A new logging method, called induction logging, is described; it measures the conductivity, or resistivity, of the strata traversed by a bore hole. The apparatus, which is briefly described, comprises a coil system coupled with the ground by induction, so that there is no need for direct contact with the mud, or with the formations. For that reason, the method is particularly useful in oil base mud, and it was first applied to that case. A discussion concerning the respective contribution of each region of ground in the vicinity of the coil system is given. Through the concept of a geometrical factor, it is demonstrated that the total signal, which measures the apparent conductivity, is the summation of the partial products — geometrical factor by conductivity — for the different regions of the ground under consideration. It is thus possible to establish, for each type of coil arangement, investigation characteristic as well as departure curves and correction charts for beds of various thicknesses. This should greatly facilitate the quantative interpretation of the field logs, even in cases where such interpretation would have been difficult on electric logs taken with electrodes. It is also shown that focussing combinations of coils can be used, which give, directly on the recorded log, a value close to the true conductivity, even for fairly thin beds, thus eliminating in most cases the need for corrections. These focussing systems also give a sharper definition of the boundaries between successive strain.

Jan 1, 1949

By R. Ingerson

Bore surfaces of used guns commonly show a pattern of cracks in various degrees of development. It has been suggested that these cracks may aid erosion by providing channelways for the gases, eventually leading to the tearing out of blocks of metal. Under the general studies of gun erosion conducted at the Geophysical Laboratory it appeared desirable to consider this factor, and to determine the resistance to surface cracking offered by gun steel and by various other materials that might be used in the bores of guns. Method and Apparatus In order to make such a determination it is necessary to have (I) an arrangement in which the surface to be studied can be subjected to conditions similar to those in a gun with respect to temperature, pressure (developed by explosion gases), composition of the gases and length of time the surface is exposed to the gases; and (2) a specimen that can be examined readily after any number of shots, and then fired again, if necessary. The first of these conditions can be met by using an explosion vessel designed by H. S. Roberts of the Geophysical Laboratory. Fig I shows a cross-section of the apparatus. The "gun" G from which the charge is fired is made from the receiver of a caliber 0.30 army rifle, M1903, and the charges are prepared in caliber 0.30 cartridge cases. The test specimen S is held in place by a cone-shaped plug P and by a steel bridge B which is bolted to the outside of the explosion vessel on either side of the section shown. The plug, in turn, is held in place by a screw collar C. Maximum pressure is controlled by a brass rupture disk R. Part of the explosion gases flow past the two flat areas on S. Temperature and composition of gases, and the time before the rupture disk breaks, can be controlled by amount and kind of powder used, and pressure can be controlled by using rupture disks of different thickness. While the explosion vessel used was not designed so that temperature and pressure could be measured, in other vessels of closely similar size and shape containing proportionate charges of the same kind of powder as that used for standard testing procedure, values of 2700°K and 50,000 psi were obtained. Since the orifices past the flat areas on the plug are small compared to the rupture disk hole (I:I6), most of the gas goes out through the rupture disk when it breaks. The amount that goes by the plug depends on (I) the pressure attained before the rupture disk breaks and (2) the time it takes for this pressure to be built UP. The second condition (examination at will after any firing) is met by using for specimens short rods that have flat areas ground on opposite sides. These flat

Jan 1, 1949

By C. M. Loeb, T. E. Norman

The use of ball, rod and tube mills for grinding ore, cement and other materials has grown so rapidly during the past forty years that the world's annual consumption of ferrous grinding media for these mills is now estimated to be between one half million and one million tons per year. Ferrous grinding balls constitute the major portion of this tonnage. Obviously they represent suficient value to justify thorough studies of the factors governing their performance. The selection of grinding balls is governed principally by: I. Quality (wear resistance, impact resistance, soundness, and the like). 2. Sources of supply and delivered cost. 3. Grinding characteristics or efficiency in the ball mill. This paper deals principally with the quality of ferrous grinding balls. In the study of these factors certain data relative to the fundamental nature of ball wear in ball mills have been obtained. These data are also presented and discussed briefly. The Development of a Suitable Wear Test A study of the fundamental factors governing the quality of grinding balls has been hampered seriously by the fact that a competent test has, in the past, involvetd the purchase of several hundred tons of halls of a specific type which were then run in one or more ball mills for a period ranging from several months' to several years' duration. Often, during the period of test, it became necessary to change operating conditions or the character of the ore fed to the test mill with the result that the rate of ball consumption changed and the test figures became of little value. Under such circumstances, progress in the development of better grinding balls, has been necessarily slow. Economic factors and variations in the quality of balls produced by different sources of supply generally make it necessary for each mill operator to determine for himself the most suitable type of balls for his mills. In our own ball mill grinding operations at Climax, Colo., we were faced with this problem. After we had run a few large scale wear tests at considerable expense we decided to investigate the possibilities of a small scale wear test which would be capable of testing numerous types of balls within a relatively short time. The most important requirement of any test is, of course, that it give results which can be used to predict accurately the wear in full scale operations. It was known that Ellis and his associates1'2 had developed a method of testing grinding balls by small scale tests run at the Ontario Research Foundation. Ellis' method of testing was used as a starting point in our investigations. In the course of our tests a number of modifications of the original method were found to be desirable so that, by an evolutionary procedure, a method of small scale

Jan 1, 1949

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By G.A. Moore, C. E. Sims

In previous publications of the writers4-7 it has been shown that vacuum extraction of steel can be carried as close to quantitative completion as desired provided the steel is in the austenitic state and sufficiellt time is allowed. For precise work, the method claims preference because the equipmelit for holding and heating the sample can be made simple, and because crucibles, boats, and other unnecessary materials can be eliminated and the blanks thus made very small. It is well known that the evolution rate of hydrogen is smaller just above the trans. formation than immediately below, as would be expected from the increase in solubility when passing into the gamma state. Many attempts have been made to obtain analyses by extraction just below the transition, using times of approxi. mately 2 hr. while it is true that the rate of evolution drops nearly to zero under these conditions, it has repeatedly been shown that the process is incomplete since on raising the temperature into the austenitic range, evolution will be resumed, usually after a, considerable induction period. The low-temperature evolution process appears to be useful in some cases for comparative tests where the residual crror may be more or less constant between samples, For general use, however, there is no guarantee that the error caused by incomplete extraction is constant; hence, the more laborious but more reliable high-temPe'atu'e Process must be used. At high temperature, an original flash evolution, similar to that at lower temperature, is first observed. After not more than an hour, the flash subsides and cvolution settles down to a regular first-order reaction rate for which the half-life* is usually of the order of a few hours for the 5/8-in. diam cylinder at 1050°C. The regular evolution may be followed for whatever period appears justified, after which the residual gas may be estimated as equal to that which was evolved in the last observed half-life period. Tests have shown that the composition of the evolved gas does not vary greatly during the progress of evolution; therefore the residual gas may safely be taken to have the same composition as the portion col-

Jan 1, 1949

By M. W. Bartley, Hugh M. Roberts

Substantial deposits of Bessemer hematite have been found recently by drilling beneath Steep Rock Lake, Ontario, which is situated in the northern part of the Lake Superior Region. It will be practicable to divert the waters flowing into this lake and develop open pits on the upper pert of two large ore bodies by damming off and pumping out the water in the part of the lake in which they occur. Ultimately, the bulk of the ore will be mined by underground methods. Owing to the generally massive nature of the rocks in the area, no underground flows of major consequence are anticipated after diversion of the lake. The Steep Rock deposits are attributed in origin to hydrothermal replacement. They were formed, for the most part, along an unconform-able, brecciated contact between the Steep Rock limestone and an overlying younger volcanic series, The replacing solutions came in as igneous after-effects, following upon the intrusion of basic igneous rocks that invaded the hanging-wall volcanics. It is believed that this took place in a geological period roughly equivalent to late Middle Huronian, which was the period when the most extensive iron-bearing rocks of the Lake Superior Region were formed. Comparison is made with other deep-seated iron-ore bodies in the Lake Superior Region, the origins of which are ascribed in the discussion to hydrothermal replacement. Introduction Under the waters of Steep Rock Lake, Ontario, situated on the Canadian National Railway, 142 miles west of Port Arthur, the presence of three ore zones containing red and brown Bessemer hematite has been established. These were discovered and have been partly explored by means of diamond and churn drilling, The positions of the ore zones, designated as A, B and C, are shown on the accompanying maps and cross sections. This exploratory work, begun in 1938 by Joseph Errington* and Julian G. Cross, has been carried on by Steep Rock Iron Mines Ltd., and was continued during the winter of 1941-1942. For more than 60 years explorers have known that large quantities of hard hema. tite float of good grade existed along the south shore of Steep Rock Lake, and the presence of ore beneath the lake was inferred by many early geologists and explorers. Despite numerous previous attempts to find ore in place, actual discovery awaited the recent period of intensive exploratory effort in Canada. The results obtained in the drill holes put down since 1938 by steep Rock Iron Mines Ltd. are not only of interest, in themselves, to those concerned with the development of ore deposits, but, taken in connection with the surface exposures of adjoining formations, they form the assemblage of facts from which the geological reasoning in this paper proceeds; accordingly, they are set out here as briefly and exactly as may be.

Jan 1, 1949

By Edwin B. Eckel

This paper, based on brief field examination and on data supplied by the operators, records the condition of the Italian mercury industry as of March 1945, not long after Italy's collapse. Except for the once-Italian but now Yugoslavian Idria mine near Trieste, virtually all the known mercury deposits are in the Monte Amiata district in Siena and Grosseto Provinces, 75 miles north of Rome. This district contains the Abbadia San Salvatore. the Siele. the Argus, and the Cerreto Piano mines besides numerous prospects and unproductive mines. Under pressure from Germany the principal mines were highly productive during the early part of the war, but production fell off long before its end. All of the mines were damaged in some way at the German withdrawal but by September 1944 the Abbadia had resumed production and several others were only lacking power by the early spring of 1945. The Monte Amiata district is characterized geologically by a thick series of sedimentary rocks that range from Triassic to Eocene in age . and are surmounted on Monte Amiata itself by a thick cap of extrusive trachyte. Bodies of travertine and of landslide detritus, younger than the trachyte, are rather widespread. The structure is complex and little known but most of the ore deposits seem to lie along or near a major, north-trending fault or on associated cross-fractures. Cinnabar is the only important ore mineral and clay minerals are by far the most abundant products of hydrothermal alteration. A southward increase in the amount of stibnite, relative to cinnabar, suggests horizontal zoning. The grade of ore ranges from 0.60 to 3.0 Pet and the reserves, as compared with those in American mines, are enormous. Even in the face of war-time scarcities, the mines are remarkably self-sufficient and labor is plentiful, but the costs of production are estimated to be not greatly below those of the better American mines. Notes on the principal mines, on the mining and metallurgical methods, and on the manufacture of synthetic cinnabar are included in the paper. Introduction With but few brief interludes, Spain and Italy, including the Idria mine near Trieste, which has passed from Austrian to Italian to Yugoslavian hands in the Past 3 decades, have led the world in the production of mercury, or quicksilver, for many centuries. Despite their enviable position with respect to the supplies of a metal so essential in both war and peace, there is a notable lack of up-to-date information in America on the mercury industry of either country. Duschak and Schuette' and Schuettez,3 give by far the best summaries in English known to the writer, but the latest firsthand report cited by them on the Italian mines was published in 1915.' Having been deeply interested in the geology and economics of mercury for several years, the writer naturally felt most fortunate in being the to obtain enough firsthand information on the Italian industry to fill at least a few of the gaps in our knowledge. The opportunity came during the war, soon after this industry, together with the rest of Italy, had capitulated to the Allies. Many of the facts presented here are thus definitely "dated," but others are of less transitory nature, and even the dated facts should be of interest in showing the strength and

Jan 1, 1949

By Paul T. Allsman, E. W. Newman

Trenching, sampling, and core drilling in Stillwater and Sweetgrass Counties, Mont., by the Bureau of Mines have delimited over 5,000,000 tons of chromite ore containing more than 20 per cent chromic oxide. The Benbow and Mouat-Sampson mines have been developed and are fully equipped for mining and milling 500 tons and 2000 tons a day, respectively. Introduction The Montana chromite deposits were the first to be explored under the Strategic Minerals Act of 1939. In June of that year, the Bureau of Mines started exploration by trenching, test pitting, sampling and diamond drilling, and completed the project in March 1943. The U. S. Geological Survey cooperated by mapping the geology and logging the cores. The project was to determine the extent and grade of the chromite ore and to indicate sufficient reserves to justify development and exploitation of the deposits for the national emergency. Exploration has indicated that the district contains the largest and most important reserve of chromite ore in the United States. The Benbow and Mouat-Sampson mines have been developed and a 500-ton concentrating mill has been constructed on the Benhow property and a 2000-ton mill on the Mouat-Sampson property. Concentrates were produced from the Benbow mill three months after the attack on Pearl Harbor, when the nation's major chromite supplies from foreign sources were cut off. History It has been known for 50 to 60 years that some chromite deposits existed in an east-west belt along the north escarpment of the Beartooth Mountains about 25 miles north of Yellowstone Park, but nothing was known of their size and extent until the war demand of 1917 and 1918 stimulated the search. In those years two properties in the Stillwater region were actively developed, but no shipments were made. The Benbow property was located in 1918 by a local group. The property comprised seven claims along the strike at the east end of the belt. An adit was driven several hundred feet on the Eclipse claim. The seven claims were sold to the Chromium Products Corporation of Livingston, Mont., and were subsequently patented. In 1929, an eastern group obtained an option, installed some equipment, and erected several log cabins. The "crash" in the market in 1929 caused the operators to drop their lease, and the property remained inactive until 1939, when the Bureau of Mines began its exploration. Fourteen claims were located on the Boulder River in 1918 and subsequently patented by the U. S. Chrome Corporation.

Jan 1, 1949

By Link. Theo A.

Introduction Since the discovery of a major oil pool at Leduc, Alberta, on February 13th, 1947, the long spell of 'oil drought' in Western Canada is now being turned into an oil and gas flood which requires immediate action to obtain the optimum economic benefits. The Woodbend, Section 9, and Okalta extensions of the Leduc field itself have been established; the Redwater pool, lying thirty-seven miles northeast of Edmonton, has been discovered and is being drilled up, and the Imperial Schoepp No. 1 or Golden Spike discovery holds promise of something phenomenal in view of the 500 feet of oil-saturated coral-reef porosity whose areal extent is not known. Imperial Stanolind Barrhead No. 1, northwest of Edmonton, revealed the presence of oil in the Madison, and just recently Gulf N.J. Ellis No. 1, some sixty miles southeast of Leduc, found commercial production in the Leduc D-2 discovery zone. In addition to these Paloeozoic discoveries, gas and oil reserves have also been established in the Upper and Lower Cretaceous, which must be penetrated by all tests on the way through the geological column to the Devonian. If ever there appeared to be an index of 'things to come' in the oil industry, this is it. However, without these recent discoveries the picture in Western Canada does and always did, look very promising indeed. A brief survey of the geological setting in Western Canada is the object of this contribution.

Jan 1, 1949

By Edwin B. Eckel

This paper, based on brief field examination and on data supplied by the operators, records the condition of the Italian mercury industry as of March 1945, not long after Italy's collapse. Except for the once-Italian but now Yugoslavian Idria mine near Trieste, virtually all the known mercury deposits are in the Monte Amiata district in Siena and Grosseto Provinces, 75 miles north of Rome. This district contains the Abbadia San Salvatore. the Siele. the Argus, and the Cerreto Piano mines besides numerous prospects and unproductive mines. Under pressure from Germany the principal mines were highly productive during the early part of the war, but production fell off long before its end. All of the mines were damaged in some way at the German withdrawal but by September 1944 the Abbadia had resumed production and several others were only lacking power by the early spring of 1945. The Monte Amiata district is characterized geologically by a thick series of sedimentary rocks that range from Triassic to Eocene in age . and are surmounted on Monte Amiata itself by a thick cap of extrusive trachyte. Bodies of travertine and of landslide detritus, younger than the trachyte, are rather widespread. The structure is complex and little known but most of the ore deposits seem to lie along or near a major, north-trending fault or on associated cross-fractures. Cinnabar is the only important ore mineral and clay minerals are by far the most abundant products of hydrothermal alteration. A southward increase in the amount of stibnite, relative to cinnabar, suggests horizontal zoning. The grade of ore ranges from 0.60 to 3.0 Pet and the reserves, as compared with those in American mines, are enormous. Even in the face of war-time scarcities, the mines are remarkably self-sufficient and labor is plentiful, but the costs of production are estimated to be not greatly below those of the better American mines. Notes on the principal mines, on the mining and metallurgical methods, and on the manufacture of synthetic cinnabar are included in the paper. Introduction With but few brief interludes, Spain and Italy, including the Idria mine near Trieste, which has passed from Austrian to Italian to Yugoslavian hands in the Past 3 decades, have led the world in the production of mercury, or quicksilver, for many centuries. Despite their enviable position with respect to the supplies of a metal so essential in both war and peace, there is a notable lack of up-to-date information in America on the mercury industry of either country. Duschak and Schuette' and Schuettez,3 give by far the best summaries in English known to the writer, but the latest firsthand report cited by them on the Italian mines was published in 1915.' Having been deeply interested in the geology and economics of mercury for several years, the writer naturally felt most fortunate in being the to obtain enough firsthand information on the Italian industry to fill at least a few of the gaps in our knowledge. The opportunity came during the war, soon after this industry, together with the rest of Italy, had capitulated to the Allies. Many of the facts presented here are thus definitely "dated," but others are of less transitory nature, and even the dated facts should be of interest in showing the strength and

Jan 1, 1949