Search Documents

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.'s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC'S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963

By Robert E. Johnson

1962 was the second year of recovery from the mild 1960-61 recession. The year-to-year gain in constant dollar gross national product, our most comprehensive measure of the country's economic performance, was 6.0 percent (from $447.7 billion in 1961 to $474.8 billion in 1962). The unemployment rate declined from 6.7 percent to 5.6 percent. Although it was a good year, there were still unused resources of labor and capital which implied that the economy was operating below its potential. The year-to-year change in the Federal Reserve Board (FRB) index of industrial production of 7.6 percent masked the fact that more than one-third of the growth took place within 196L The monthly index rose only 4.8 percent during 1962, from 114.3 in January to 117.8 in September. The fact that the economy as shown by the industrial index, rose rapidly in the first half of the year only to remain on a plateau of 119-120 during the second half, led some people to fear an imminent downward turn. This did not occur. Neither production nor consumption of mineral fuels advanced as fast as the total economy. But consumption showed more gain than production, 5 percent compared with somewhat less than 4 percent. Production of both crude oil and natural gas reached new highs while bituminous coal production was the highest in 5 years.

Jan 1, 1963

By D. L. King, C. D. Rubert, R. W. Christy, B. A. Schepman

R. W. Christy (Manager of Sales, Sanitary Engineering Equipment, Link-Belt Co.) and C.D. Rubert (Barrett, Haentjens & Co.) — Messrs. King and Schepman have presented an excellent paper which outlines the general practice in the design of thickener mechanisms. Lifting devices, controls, special applications and underflow pumping arrangements have been reviewed in detail. Pumping arrangements were illustrated which eliminate the need for an expensive tunnel beneath the thickener floor. Most of those illustrated have the common feature of a relatively long underflow suction line extending from the hopper floor to the pump located on the bridge at the periphery of the tank. The authors limit these arrangements to comparatively dilute or thin slurrys. It is implied that dense and coarse concentrates, which are difficult to pump, cannot be handled unless a tunnel is constructed. Fig. 1 shows an underflow pump arrangement which negates the need for a tunnel but which permits the operator to convey a heavy dense slurry. The pump is mounted directly on the fixed hoist platform and the impeller is located at the base of the steel center column. Priming water is not needed. The column

Jan 1, 1963

Several factors contributing to the loss of fibre during treatment are a function of the paragenesis of the veins. The occurrence, of magnetite from the cap rock within the veins prevents complete fiberization. There is a marked similarity between these veins and those in the Koegas-Westerberg area of South Africa.INTRODUCTIONAn investigation of the mineralogy of the Wittenoom Gorge crocidolite veins was undertaken in the latter part of 1962 at the request of the Colonial Sugar Refining Co. Ltd. It was anticipated that such a study might reveal the cause or causes of the lack of recovery of some asbestos during beneficiation. Some interesting features of the mineralogy and paragenesis of the crocidolite veins become apparent, but it is emphasized that the investigation is far from complete, as the study did not extend to the field occurrence.The samples examined were selected from the mill and from the untreated ore.GEOLOGICAL SETTINGWittenoom Gorge is situated on the Fortescue River in the Hammersley Ranges of Western Australia and is one of several gorges in these ranges, on the sides of which 'crocidoIite asbestos is known to occur. The Hammersley, Ranges consist essentially of a series of quartzites, shales, ferruginous quartzites and dolomites. These' rocks are part of the Nullagine Formation (Proterozoic) and are usually either horizontal or gently folded. In some 'areas small beds of riebeckite as well as crocidolite are known to occur interbedded in the sequence.Riebeckite is a monoclinic amphibole, the formula of which may be stated as Na2Fe2"Fe2" (OH) 2Si8O22, and crocidolite is a fibrous variety of this mineral. This formula...

Jan 1, 1963

A pilot plant was constructed for the low temperature carbonization of Wallarah (N.S.W.) coal at the rate of 300 lb/hr. The design was based on an entrained state carbonizer developed by Parry and D.S. Bureau of Mines co-workers. Prior to delivery to the client, the plant was successfully operated over periods of several days duration.INTRODUCTIONIn September 1961, the Australian Mineral Development Laboratories (A.M.D.L.) was engaged by the Broken Hill Pty. Co. Ltd. (B.H.P.) to design, construct and test an entrained state coal carbonizer with a capacity of 300 lb/hr of Wallarah (N.S.W.) coal. Char product was required within the specification 15·5 -I- 1 per cent volatile matter. The design was to be based on a pilot plant developed by Parry and others in the D.S. Bureau of Mines Coal Research Laboratory at Denver, D.S.A. The method involved the carbonization of fine coal by entrainment with air in an externally heated reactor. The heat required for the carbonization of the coal was to be supplied to the bed both through the reactor walls, and also by internal combustion of products in the bed. Several D.S. Bureau of Mines Reports of Investigations weFe used as the main guide to the physical layout and proportions of the plant. However, the individual units required detailed designing, before engineering drawings could be prepared and fabrication begun.A 10 ton sample of crushed Wallarah coal was used for preliminary testing of the plant. The first test run on the pilot plant was carried out in February, 1962. After some modification a second test of longer duration was conducted in August, 1962. These operations aimed at running in the plant and also at determining the operating temperature to produce specification char and the maximum capacity of the...

Jan 1, 1963

By McKenzie P

The techniques of geological control developed by the Coal Geology Sections of the Broken Hill Proprietary Company Limited and Australian Iron and Steel Proprietary Limited in providing geological service in the coilieries operated by these associated companies cover the provision of geological control for both planning and production in each of which the significance of geology has in the past been only poorly appreciated by the coal mining industry.While the adoption of similar techniques is well within the capacity of major companies there is considerable scope for the development of government geological services providing specialized assistance of this nature for smaller scale producers.INTRODUCTIONThe coal mining industry in Australia can instance many notable mistakes caused by failure to obtain sufficient geological information or by incorrect interpretation of available geological evidence both before the commencement of mining and during the progress of operations. Substantial development undertaken in, areas with insufficient or inferior coal reserves, difficult mining conditions caused by failure to adjust operations to geological circumstances, and the irregular development of mine workings caused by unexpected geological features, all bear witness to the lack of geological foresight by the industry.Along with the more widespread general use of applied geology, an increasing acceptance has developed during the past ten years of the valuable contribution which can be made by this science to the exploitation of coalfields. In spite of the advances which have been made, there is still a wide scope for further detailed application of geology throughout the coal mining industry in Australia.

Jan 1, 1963

Prominent among the ore minerals at Mt. Ellison, in the Brock's Creek district, Northern Territory, are a number of copper-bismuth sulphides wittichenite, aikinite, emplectite, in association with nativebismuth, chalcopyrite, bornite, chalcocite, sphalerite and linnaeite.Linnaeite and aikinite formed first and were followed by native bismuth. Wittichenite was later and substantially replaces earlier minerals. Replacement of aikinite by wittichenite has produced secondaryor reaction bismuth.INTRODUCTIONThe Brock's Creek district of the Northern Territory lies to the south east of Darwin and has been the locale of intermittent mining of small but rich deposits of diverse ore type. Gold, tin, and copper ores were recovered especially between 1890 and 1910 with minor exploitation up to the present time. Copper ores were of prior importance, the main production coming from supergene enriched deposits of chalcocite.The mines are situated in strongly folded Precambrian strata comprising slates, sandstones, volcanics and amphibolites with replaced haematitic rocks (Sullivan, 1953). The strata in the Brock's Creek area immediately north of the Darwin-Birdum railway line are domed around a roughly circular granitic mass some 5 miles in diameter. The Mount Ellison mine is located near the N.E. margin of the granite in metamorphosed basic country rock.Study of a series of polished sections from Mt. Ellison revealed the presence of linnaeite, chalcopyrite, bornite, aikinite, wittichenite, emplectite, bismuth, sphalerite, and chalcocite. With the exception of sphalerite and emplectite each of these minerals is prominently developed and intimately intergrown with the other constituents.

Jan 1, 1963

Most mines in the Bundamba, North Ipswich, and Rosewood districts of the West Moreton coalfield of south eastern Queensland have installed washing plants during the last five years. Many problems were encountered in their installation, including the small size of washing plant required in many cases, the economical minimum ash content under present and future market requirements, production from a one-product washbox of large and small coal of quality to satisfy both markets, measures to avoid adding unnecessary moisture to the washed slack coals, and excessive middlings in some coals or soft clay in others.INTRODUCTIONIt was fortunate for Brisbane, which was to become the capital of a new State, Queensland, in 1859, and grow into a city of over half a million people by the time of its centenary, that coal was found in abundance almost on its doorstep near Ipswich, the first mine being opened at Redbank in 1843. This was followed by the opening of many more mines in that district and, some 40 years later, in the nearby Rosewood district where high-volatile gas coal was produced (Fig. 1). These discoveries ensured a supply of reasonably priced coal (currently about 85/- per ton delivered) in Brisbane, but the quality is inferior to that of other coals mined in Queensland beyond economic range of Brisbane.Various factors led to an increase in the average ash content of the West Moreton coals during and after the war. Between 1940 and 1952 the gasworks coals rose in average ash from 13 8 per cent to 23·9 per cent and the powerhouse coals from 17·1 per cent to 27·1 per cent. This drift was arrested by the installation of 28 screening and picking plants from 1952 onward, but it became obvious that mechanical cleaning of the coals was essential due to the competitive market for coal and the worsening quality of reserves.

Jan 1, 1963

By C. L. Coldren

Recently there has been much discussion of the use of pipelines for the long-distance transportation of solids. Many have come to recognize the economies inherent in pipeline transportation. The widespread movement of oil and gas at astonishingly low costs - a gallon of oil moves from Montana to New York for less than that for the delivery of a postcard - has spurred others to sturdy this mode of transportation. Most interested people are aware of the inherent advantages of pipelines - continuity and reliability of operations - low manpower requirements per ton mile - moderate capital costs per ton mile - low maintenance costs per ton mile - low operating costs per ton mile.

Jan 1, 1963

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330 lb/sq. in. tension to 3,750 lb/sq. in. compression. Photoelastic examination of loaded plastic and actual rock model mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a borehole extensometer and a series of anchors at various horizons to 30 feet in a vertical roof borehole showed that when a standing face was advanced the roof movement was practically confined to the lower two feet. The majority of this movement occurred during the 36 hours after mining at this face commenced.The use of a radioactive isotope and a scintillation counter in a pair of parallel boreholes is a sensitive and accurate method of roof bedding plane crack detection.INTRODUCTIONA knowledge of strata stresses is required to understand the deformation of an underground opening and, in particular, the roof behaviour. It is the aim of investigations currently being conducted by Australian Coal Association (Research) Ltd. to determine the stress existing around mine openings and the location and magnitude of roof movement.STRATA PRESSURE MEASUREMENTMost measurements of strata stress are performed at the surface of underground openings and the majority measure the change of strain resulting from stress relief. The accuracy of the measured value of stress depends upon knowledge of the rock modulus of elasticity. The flat jack method has the advantage that strain relief is restored by a measured stress applied directly by the jack. The rock modulus of elasticity can also be determined.

Jan 1, 1963

Drilling at Ipswich during the last twelve years by the Queensland Department of Mines has proved large quantities of reserves which have assured the security of the field for many years to come. This is perhaps the greatest contribution to the development of the field since its discovery in 1827.The drilling campaign commenced in 1950 and by the end of 1961 comprised 242 holes totalling 180,220 ft.Intersections of formations and seams, accompanied by detailed surface mapping, led to more precise knowledge of the geology of the field than was previously possible, and clarified many problems of correlation. Productive formations are part of the Middle Triassic Ipswich Coal Measures, a 4,300 ft sequence of fresh-water sediments with some interbedded volcanics. They are overlain by the Upper Triassic Bundamba Group and the Lower Tertiary Booval Group.Reserves disclosed by drilling amount to 171,487,000 tons, comprising 109,407,000 tons "measured" and 62,080,000 tons "indicated". The security of these reserves encouraged many collieries to instal modern efficient mining machinery and washing plants.The climax of recent development of the resources of the field will be the commissioning in 1966 of a £33 million 360 MW power station in the Swanbank district which will consume 14 million tons of coal during its 30 year life and will have a peak demand of some 20,000 tons per week.Drilling is continuing and is expected to prove additional reserves which will justify further development of the field.INTRODUCTIONUntil 1949 there had been no concerted effort to test systematically the resources of the whole Ipswich field. Fifty two known holes totalling 30,500 ft had been drilled, eight of them by the Department of Mines, but because of poor core recovery and inadequate records most of them were of little use in a comprehensive assessment.Development of the field was being retarded by uncertainty regarding reserves and by the general state of the coal mining industry. Numbers of comparatively small independent companies and owner groups were operating coal...

Jan 1, 1963

By R. S. Craig, W. E. Wallace, G. S. Kamath

The destruction of long-range order in Mg-Cd, has previously been thought to occur as a second order process. In the present work a variety of X-ray diffraction techniques are employed to show that in this case and in Mg-Cd alloys containing frorn 20 to 33 1/3 at. pct Mg the process more nearly resembles an ordinary first order phase transformation. It is found that the ordered alloy, which occurs as a single phase at lgw temperatures, transforms with increasing temperature into a Cd-enriched disordered (P) phase and an Mg-enriched ordered (a) phase. The interval over which these two phases coexist under apparently equilibrium conditiovs extends from 25" to 87°C content. At 33 1/3 at. pct Mg the two-phase region has disappeared. Measurement of the long range order parameter, s, for the ordered phase in MgCd, (from superlattice line intensities) shows that it disorders only very slightly before it is transformed into the p form. Kinetic experiments reveal that when the a phase is formed frorn the p phase by suitably quenching so as to suppress phase segregation, the transformation is essentially complete and the a phase has acquired its equilibrium value of S in less than 1 min. In an earlier investigation carried out in this Laboratory1 the rate of disordering of the MgCd3 superlattice was determined over an extensive range of temperature. The process was found to be first order and the rate constant, k, was established. At the lowest temperatures studied k was found to increase exponentially with temperature. At higher temperatures, however, it passed through a maximum and for the 100 deg interval below the point at which the superlattice was destroyed k was observed to decrease with increasing temperature. The various theoretical treatments1-3 of order-disorder phenomena lead to a negative temperature coefficient for k near the superlattice critical temperature but this region for MgCdB seemed unusually wide. Detailed analysis of the point indicated' that either the long-range order parameter, S, for MgCda varied with temperature in an anomalous way or the disordering in this instance is more complex than in the cases which have been treated theoretically. The original objective in the present work was simply to determine S vs temperature for MgCda to ascertain whether the disordering was in conformity with theoretical expectations.2° In an early stage of the work it was noted, however, that under equilibrium conditions ordered (a) and disordered (0) phases coexist in MgCd, over a considerable range of temperature. Since on thermo- dynamic grounds the coexisting phases must differ in composition, the investigation was enlarged to permit the compositions of the two phases in MgCd3 to be determined and to establish the extent of the two phase regions for alloys containing from 20 to 33 1/3 at. pct Cd.

Jan 1, 1963

Jan 1, 1963

Copper, zinc, lead, and silver in the discordant magmatic-hydrothermal orebody of the Conrad Mine, N.S.W., all have a relatively high mean abundance. Any single concordant sulphide orebody containing the same metals has a similar order of mean abundance of only one or two of these, particularly copper, copper and zinc, or zinc and lead.The relative abundances of the metals in the Conrad orebody vary more widely than in concordant orebodies, and the lead-zinc-silver and copper-zinc-lead relationships are significantly different.INTRODUCTIONIn previous investigations of metal abundances in sulphide ores, the basis of selection of the orebodies was their form, and to some extent their geological setting, rather than hypotheses concerning their origin. In all cases they were generally concordant with the bedding of the sedimentary or meta-sedimentary rocks enclosing them, and most occurred in volcanic-sedimentary sequences. Their mineralogies were simple, and they were copper, copper-zinc, zinc or lead-zinc rich in composition. Most were of the type ascribed by several authors to exhalative-sedimentary processes.In one of these investigations (Stanton, 1958), it was pointed out that since the metals in ores of this type showed similar abundance patterns and behaviour, it would clearly be of interest to examine, and to compare with them, orthomagmatic and vein types, unquestionably derived from their igneous rock associates.The present investigation is concerned with a single orebody, of clearly discordant type, and of indisputable hydrothermal origin. The abundance and behaviour of copper, zinc, lead, and silver have been determined and compared to similar data fOl!' the concordant type. Such a comparison tests the possibility that metal abundance patterns of base metal ores may be indicative of the mode of ore deposition.

Jan 1, 1963

By W R. Honeywell

Two series of laboratory flotation tests were carried out to study the treatment of Faraday ore by two-stage flotation. First the acid-consumers and then the uranium minerals were floated. On ore ground in the Faraday mill grinding circuit, and using Faraday mill water in the flotation step, a recovery in the flotation concentrate of from 91 to 93 percent of the uranium was obtained in 45 to 50 per cent of the weight at a grade of 0.24 per cent U30s. The saving of acid in leaching the uranium-bearing flotation concentrate, as compared to leaching the whole ore, ranged from 30 to 46 per cent. The average over-all extraction resulting from flotation and leaching of the flotation concentrate was 88.1 per cent. The best collector for the acid-consumers was sodium oleate. Acintol F A-1 emulsion was the best collector for the uranium minerals, and, in the uranium flotation step, an acid pH in the slurry was found to be necessary. The reagent costs were estimated to be 22 to 26 cents per ton of ore.

Jan 1, 1963

By F. D. Stevenson

Thermodynamic properties of metal halides and, in particular, vapor pressures have become of great importance in recent years owing to increased application of chemical processing to extraction of metals from their ores. Vapor pressure data serve not only as a valuable source of latent heat of vaporization and fusion values but also differences in metal-halide vapor pressures often provide the basis for their separation by conventional mass transfer operations. This literature search was made to provide a ready reference to experimental vapor-pressure data of metal halides and oxyhalides. Results are reported in two main sections: (1) A tabulation of vapor- pressure references for each of the metal halides (listed by metal) for which actual experimental data are reported (table 1), and (2) a bibliography of the citations. Metal halides and oxyhalides are listed by chemical formula and chemical name, based on the stock4 system. To facilitate location of the references, a listing of the journal titles and their abbreviations follows the bibliography.

Jan 1, 1963

By OÆBrien R. T

A small static bed was used to study the thermal cycles required for the heat hardening of pellets based on synthetic magnetite concentrates and a naturally fine hematite. This apparatus can be employed to yield broad process data for the design of a recuperative strand system operating on the magnetite concentrates.Various alternatives are given for a process to heat harden the hematite ore but a preference is given to the production of a self fluxing pellet. Bond types and general mineralogical structures are interpreted against the optimum firing cycle necessary to produce a defined quality of pellet.INTRODUCTIONThe work reported in this paper extends that on the "Heat Hardening of Artificial Magnetite Pellets", which was described at the International Symposium on Agglomeration, sponsored by the American Institute of Mining, Metallurgical and Petroleum Engineers at Philadelphia, U.S.A. in April 1961. Whereas that work was of a more basic nature, serving to illustrate the suitability of artificial magnetites with various admixtures, to the application of heat hardened pellets, on this occasion the aim is to illustrate the procedures which were used to establish the dimensions of commercial recuperative strands for Australian raw materials.The nature of the pellet feed, Le. relatively uniform spheres of + i in.-Yi6 in. diameter, makes it possible to use small scale static pots for test work. By the use of a closed system and the measurement of suctions, gas flows...

Jan 1, 1963

By Haigh J. E

An accurate measure of the earth's magnetic field can be made in a few seconds with the portable proton precession magnetometer. Such an instrument increases the applicability of the long successful method of magnetic prospecting for minerals. As an example of the usefulness of the proton magnetometer, a survey over volcanic rocks near Apsley (Tas.) was made.INTRODUCTIONA completely portable magnetometer whose operation is based on the free precession of polarized protons in the earth's magnetic field, is now available on the market at a price competitive with magnetometers based on the classical physical principles. The ease, accuracy, rapidity, and reliability with which measurements of the earth's total magnetic field can be made with the proton precession magnetometer, led to the try-out of the instrument in an actual field problem so as to evaluate fully the capabilities of the instrument. Such evaluation is important, because the history of magnetic prospecting has shown that whenever significantly improved instrumentation has been introduced, prospecting costs have been substantially cut and many areas in which the prospecting costs were formerly considered excessive in relation to probable returns, have become economic mineral prospects. The proton precession magnetometer offers the possibility of opening up new areas for successful magnetic prospecting.AN OUTLINE OF THE HISTORY OF MAGNETIC PROSPECTINGWhile an outline of the history of magnetic prospecting is not directly connected with the evaluation of a proton pre...

Jan 1, 1963

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world output for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By C. H. Riggs

This report describes the development, oil recovery, and potentialities of productive formations in the Hall-Gurney field, Russell County, Kans. It is presented as part of a general program to aid and promote increased recovery from petroleum reservoirs. The report is based on studies of well logs, drill cuttings, and oil-and water-production histories of individual wells and leases. The geological interpretations follow closely those in published literature with only slight local modifications. Oil and water analyses, made at a Bureau of Mines research center, were supplemented by many analyses obtained from oil-producing and service companies. The Hall-Gurney field, in south central Russell County, Kans., (fig. 1) was discovered in 1931 but was not developed extensively until 1941. By 1960 the rate of oil production from the field had declined to the extent that many wells were abandoned. In some areas natural productive forces have effected good recovery. However, in other areas inefficient waterflooding, both natural and accidental, has adversely affected recovery potentialities.

Jan 1, 1963