Search Documents

The Cowarra gold mine is at latitude 36°O'S. and longitude 149°19'E. which is roughly 20 miles north-north-east of Cooma.The deposit was· originally worked towards the end of the last century, but the presence of sulphides associated with the gold in the primary zone caused cessation of work when that zone was reached.GEOLOGY AND MINERALIZATIONThe principal country rocks are sandstones and shales of Silurian and Ordovician age, both very strongly folded with structural pitches ranging from a few degrees to almost vertical. The mine proper is within Silurian rocks and the main orebody (there are several minor parallel bodies) is developed within a shear striking approximately north, dipping approximately 70° east, and ranging in width from 2 ft to 15 ft but averaging about 4 ft.This shear is impregnated with quartz and sulphides with which the gold is associated. The predominant sulphide is pyrite though pyrrhotite is commonly present in quantity.Arsenopyrite and bornite are present in smaller amounts.Stillwell (1936, 1937a, 1937b, 1938, 1941) has published five mineragraphic reports on the ore.The various levels have been mapped in detail (Figs. 1-3) and the No. 2 level plan (Fig. 1) shows the general relationship of shearing, as now indicated by mineralization, and faulting. There is no apparent connection between the fold structures and mineralization.Fig. 3 is a longitudinal projection showing the distribution of gold expressed as inch-ounces. The estimation of...

Jan 1, 1965

By S. A. Mersol, C. T. Lynch, F. W. Vahldiek

The room-temperature Knoop hardness of single -crystal titanium diboride has been determined. Variations in microhardness have been correlated with orientation and structural imperfections in the crystals. Maximum differences in hardness values of 750 kg per sq mm with respect to orientation and 450 kg per sq mm with respect to substructure were found. The effects of etchants, load on indenter, and degvee of cracking of indentation were studied. The average hardness was determined as 2800 kg per sq mm on the as-grown crystals. Annealing increased the average hardness to 3375 kg per sq mm. ThE microhardness of polycrystalline titanium diboride approximating the stoichiometric composition TiB, has been studied by several investigators. The values for the Knoop hardness number range from 2710 kg per sq mm (Khn = 2710 kg per sq mm) to 3400 kg per sq mm.'-4 Samsonov et al.' reported a Vickers hardness number of 3400 kg per sq mm (Vhn = 3400 kg per sq mm) at 120-g loads for a 98 pct Ti + B material of 96 pct theoretical density. Recently Dunegan measured the Vickers hardness and obtained 2060 kg per sq mm with a 10-g load (Vhnlo = 2060 kg per sq mm), 1425 kg per sq mm for Vhnloo, and 1320 kg per sq mm for Vhnlooo. We have obtained a Khnloo = 3000 * 350 kg per sq mm for hot-pressed polycrystalline TiB2 that was 99.1 pct Ti + B and 96.6 pct of theoretical density. The present investigation has been made on single-crystal titanium diboride boules, and is believed to be the first such study on TiB, crystals of known orientation. EXPERIMENTAL The single crystals were prepared by a Verneuil-type process using an electric arc by the Linde Division of Union Carbide Corp. The largest specimens were 6 mm in diameter by 12 mm long. The crystals were of theoretical density (4.50 g per cm3) with a Ti + B content of 99.8 pct. The major impurities present were: 0.03 pct (by weight) 0, 0.06 pct C, 0.01 pct Si, 0.05 pct Fe, 0.01 pct Cr, and 0.01 pct Ni. The crystals were boron-rich, the average boron content being 31.S7 wt pct (stoichiometric value is 31.12 wt pct), and titanium-poor, the average titanium content being 68.2 wt pct (stoichiometric value is 68.88 wt pct). Titanium was determined gravimetrically by cupferron precipitation and boron by titration of H3B03 from a NaOH-fused specimen after removal of titanium with BaC03. The outer edge of the boule accounted for some of the excess boron. An electron-microprobe analysis showed that the titanium content increased from 60.0 wt pct at the edge to 68.5 wt pct at D, ~ 1000 p, where D, = distance from outer edge (see Fig. 5). X-ray measurements indicate that the boules are single crystals with considerable substructure. Upon etching this structure is seen in the form of a Widmanstatten-type rhombohedral line pattern in the basal (c) plane and a parallel "lines" pattern in the prism (a) planes. A typical WidmanstHtten-type pattern is seen in in Fig. 1. Electron microscopy reveals that the lines are less than 1 p across, which does not allow direct electron probe or microfocus X-ray determination of their composition. The identity of the second phase has not been established. It might be a higher boride or a nonstoichiometric TiB2. On annealing above 2200°C the precipitate is dispersed and dissolves in the matrix. The best etchants found were HF/HNO/HO, KF(CN)$NOH/HO (Murakami's Etch), and A large number of other etchants were previously Studied. The acidic etchant produced an acicular or "needles" pattern in the (a) planes which is an etchant effect on the "lines" pattern.

Jan 1, 1965

By Joseph Grumer

The range of composition of gases synthesized from solid fuels which are exchangeable with natural gas on current gas appliances was evaluated by theoretical principles. These principles consider primarily the flashback, blowoff, and yellow-tipping characteristics of air-entraining burner flames. It was found that complete identity between the synthetic and natural product is not necessary. Gases such as may be obtained by hydrogasification of coal and other solid fuels without the removal of unreacted hydrogen offer advantages in flame characteristics. Between 25 to 37 percent hydrogen can be tolerated in the sendout gas.

Jan 1, 1965

Recently discovered Carboniferous bentonites are variable in charadeI and thickness, but being altered aeolian, ash-fall tuffs, they are probably extensive. Most are the Ca-montmorillonite type without the natural swelling characteristics of the Wyoming deposits, but their situation, thickness, and response to beneficiation through cation exchange may give them some potential as sources of future economic deposits.INTRODUCTIONLoughnan and See (1959) gave an account of bentonites and fuller's earth deposits of New South Wales. The most likely potential industrial sources were those occurring in the uppermost formations of the Newcastle and Singleton Coal Measures (Permian) in the Hunter Valley and deposited during epochs not marked by strong contemporary vulcanicity.One feature of the record of known occurrences at that time was the absence of bentonites from the thick volcanic sequences of the Carboniferous, but since this paper appeared, many bentonite beds have been discovered by the writer in the Carboniferous facies formerly known as the "Kuttung Series".The purpose of this contribution is to report briefly on the occurrence, genesis, mineralogy, and economic potential of these deposits which augment possible sources of bentonite near major industrial centres on the eastern seaboard.The potential world demand for bentonite would increase markedly with the trend to pelletization in the steel industry, if its use in this field became more general. More detailed mineralogical studies will be presented in later publications.STRATIGRAPHIC DISTRIBUTIONBentonite occurs at irregular intervals throughout a thick sequence of dominantly continental, plant bearing strata...

Jan 1, 1965

Hatches Creek has been inactive since 1961, but with better metal prices, interest in the field is reviving.The mixed gravity concentrates which were unsalable in 1951 have been experimentally separated into salable wolfram, scheelite, and bismuth-gold concentrates, and a flow sheet incorporating magneticseparation and flotation has been developed.

Jan 1, 1965

The Red Lake greenstone belt is an irregular mass of lavas sedimentary rocks and intrusives which is approxiately 35 miles long 18 miles wide and 7 miles deep. Basaltic volcamcs are the oldest rocks w1thm the belt. They are believed to have been laid down on an ancient crust which is at least 3 billion (3 x 109) years old and was composed partly of sediments. The basaltic rocks are overlain by acid volcanics and sedimentary rocks which have been complexly folded and are preserved as a down-folded remnant of younger rocks within the older crust. The volcanics and sedimentary rocks of the greenstone belt have been cut by intrusives with a wide range of composition. The emplacement of the intrusives and the accompanying regional metamorph-ism which terminated the orogenic activity in this area are believed to have occurred approximately 2.4 billion years ago. The basalts and many of the basic and ultrabasic intrusives undoubtedly had their source in the sub-crust or mantle. At least some of the granitic intrusives are believed to have had

Jan 1, 1965

By V. Koump, T. F. Perzak, R. G. Olsson

Jan 1, 1965

By Hsun Hu, R. S. Cline

The effect of rate of deformation on texture formatiotz has been studied with cube-oriented single crystals of 3 pct Si-Fe, compressed 80 pct at two widely different rates. Compression at a low rate (crosshead speed, 0.1 ipm) produces large orienta-tional changes and coarse deformation bands, whereas little change in orientation is observed, particularly at the surface of the crystal, when compressed at a high rate (impact velocity, -500 ips). Thin plates of mechanical twins are produced at the high rate, but their contribution to the deformation texture is practically negligible. The crystal deformed at a high rate has a lower hardness and a more uniform dislocation structure and is morc resistant to recrystallization. There is also a dilference in the recrystallization texture between the slowly and rapidly compressed crystals. These results indicate that plastic flow is less "turbulent" at high strain rates than at low strain ratcs. THE behavior of metals under high-speed deformation has been the subject of wide study in the past decade. Most of these works were concerned with mechanical properties during testing at high rates of loading, the resulting structures, and the theoretical aspects of the observed phenomena. The present status of knowledge and research activities in this field has been documented in recent publications.17' There is, however, very little information available in the literature concerning the effect of high-speed deformation on the texture formation in metals. The possibility of an effect of rate of deformation on texture is suggested by the microstructural differences observed between normally and very rapidly deformed samples. Aside from the strong tendency for twinning (and phase transformation in certain metals) in high-speed deformation, the slip-line patterns and the dislocation configurations show marked differences as a result of large differences in the strain rates. For instance, in mild steel in static and dynamic compression, Campbell and co-worker3,4 observed that coarse slip occurred on several systems in specimens deformed at normal strain rates, whereas specimens deformed rapidly showed only fine slip on fewer systems, the slip-line pattern being very similar to that in specimens deformed at low temperatures and at normal strain rates. The absence of multiple slip was also noticed by Dieter5 in shock-loaded nickel. The dislocation configuration in an iron shock loaded at 70 kbar pressure was shown by Leslie et al.6 to be similar to that produced by light rolling at low temperature—the dislocation lines were mostly straight and uniformly distributed. These observations suggest that the mode of deformation at high strain rates is notably different from that at low strain rates. Consequently, the nature and the extent of lattice reori-entation during deformation should also be different. This investigation was undertaken to test this idea. MATERIAL AND METHOD The remaining part of a single-crystal ingot of a 3 pct Si-Fe alloy,* prepared for an earlier investi- gation,1 was used in the present studies. Specimens 9/16 in. square and 0.365 in. thick were cut from this ingot with (001) planes parallel to the square surfaces, and the [loo] and 1010] directions parallel to the edges of the specimen, within ±1 deg. These machined crystals were etched to remove distorted metal, and annealed at 1300°C for 24 hr in a purified helium atmosphere. The annealed crystals had a hardness of 161 Dph. The crystal orientation was rechecked with X-ray back-reflection techniques. In high-strain rate experiments the crystal was compressed in a Dynapak machine to approximately 80 pct reduction in thickness (from 0.360 to 0.070 in. with an impact velocity of -500 ips). Thus, the duration of loading was approximately 6x 10-4 sec, and the average strain rate was about 103 sec-1. As a result of this rapid, severe deformation, the specimen became a roughly circular thin disc. The original shape of the crystal, however, could still be recognized by a diffusely outlined square area in the center of the disc. For compression at a low speed, the crystal was deformed in a universal testing machine at a rate of crosshead movement of 0.1 ipm. Compared with

Jan 1, 1965

By Belcher C. B

A procedure was required for the rapid determination of silicon in low-alloy irons and a suitable method used the formation and reduction of silicomolybdic acid at 50°C. The procedure gives results for elemental silicon and this enables the correct computation of oxidation requirements in basic oxygen steelmaking. The method could be useful in iron foundries which have not installed direct reading spectrometers.INTRODUCTIONOxygen steelmaking experiments required rapid determinations of 0,5-1,6 per cent silicon in iron (3-4 per cent C) within 10 min of sampling; a reproducibility better than ±0.03 per cent Si was desired. Only elemental silicon (Si°) is of interest as a fuel in basic oxygen steelmaking technology, and the proposed procedure determines exclusively this form of silicon. The method is described as it may prove useful to other workers although the interference study would be incomplete for some applications.The analysis of silicon in iron is frequently obtained using direct reading spectrometers, but for the proposed experiments the spectrometers could not be used because of the prohibitive distance from the furnace. It should be noted that spectrometers determine both the elemental silicon and that present as silicon dioxide in occluded slag and inclusions.The silicon content of iron and steel is determined in this laboratory by spectrophotometric measurement of a "molybdenum blue" colour. The reactions involved have been extensively investigated; Strickland (1952) showed that a...

Jan 1, 1965

By Edwin M. Thomasson

HELIUM SHIPMENTS in 1964 exceeded the volume shipped during the previous year for the 15th successive time. Shipments from Bureau of Mines helium plants were 667.4 million cubic feet,2 about 6 percent more than in 1963. Production at Bureau of Mines plants totaled 784.5 million cubic feet. An additional 3,193.1 million cubic feet, which was produced by private companies participating in the helium conservation program, was purchased by the Bureau and stored underground for future use. The Bureau of Mines continued to sell helium at $35 a thousand cubic feet, the price established in 1961. Substantial railway freight rate reductions for tank car shipments of helium went into effect during the year, resulting in a lower delivered price for helium. As the Nation moved ahead in the space age, it became increasingly apparent that helium would continue to play an essential role in research, in technology, in defense, and in industry.

Jan 1, 1965

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1962, to June 30, 1963, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1963; in general, the research reported in these publications antedates the report period.

Jan 1, 1965

By R. Schuhmann

Jan 1, 1965

The 8 ft by 91/2 ft drive which joined No. 7 Shaft with Browne Shaft on the 1,480 ft level was extended from both ends and met at a point approximately 12,000 ft from No. 7 (2,000 ft from Browne).The surveying required for this 2 1/2 mile haulage drive called for greater accuracy than was obtainable from South Mine standard methods. Procedures and devices from published information were tried and modified as required to suit local conditions. Several new methods were applied and improved as the drive advanced. The control of angular, linear and level measurements was perhaps considerably in excess of the requirements, but this was offset by abnormally large discrepancies resulting from shaft plumbing. The accuracy of the final breakthrough, although not to the standard desired, was sufficient to complete the connection without inconvenience and added cost.INTRODUCTIONThe acquisition of the Browne Shaft leases in January 1962 presented the management of Broken Hill South Limited with the problem of transporting ore from these leases to its mill. It was eventually decided that diesel locomotivehaulage through a 2t mile drive on the 1,480 ft level between the two mines was the best solution. The drive was advanced from both ends after Browne Shaft was deepened by 80 ft to reach the 1,480 ft level horizon. Each end advancedabout 15 ft/day with the miners working three 7 hr shifts. Blasting was restricted to the end of the shift.The survey work involved five shaft plumbings and 78 theodolite stations in a traverse, underground and surface,of more than 5 miles. Because of the exceptional length of the drive, an unusually high degree of reliability was required.The aim was for a maximum error at breakthrough of 1 ft 1 in 30,000, and to secure this, precise methods of linear measurement were necessary. Shaft plumbing in particular posed special difficulties.

Jan 1, 1965

By R. J. Reynik, F. R. Meeks

IN the classical paper1 of Mehl and Rhines entitled "The Rates of Diffusion in the Alpha Solid Solutions of Copper", the authors state: "It has been mathematically demonstrated that the treatment of the data as though the diffusion were taking place between two flat plates instead of radially in a cylinder has no appreciable effect upon the results. Were the bars of a much smaller diameter, a modification of the analytical treatment would have been required." Unfortunately, the errors in the reported concentrations are much too large to neglect, as shown in the results below. A planar treatment of diffusion data assumes that the reference planes separated by a nominal distance (AX) have identical areas. An adjustment must be made on the concentration data should the successive diffusion planes differ in area. The Mehl-Rhines' diffusion samples were cylindrical with copper electroplated onto copper-based alloys. Successive surface areas through which diffusion occurs are in the ratio ri/r1, where ri is the radial distance between the center of the sample and the center of the i th shell to which the host (alloy) atoms diffuse, and r1 is the radial distance between the center of the sample and the center of the innermost (i = 1) experimentally reported shell from which the alloy atoms diffuse. Hence, ri/r1 (i = 1, ..., n layers) is a dimensionless correction factor to be multiplied by the reported concentration data before planar-data analysis is attempted. In the forty-seven samples reported, the original interface between the copper alloys and the electroplated copper was located at a mean distance of 8.255 mm from the center of the samples. The successive layers, machined off the samples, were approximately 0.0762 mm thick. The distance (xi) at which concentration (ci) was reported was always a distance measured with respect to the original interface, that is, with respect to the fixed distance of 8.255 mm. Hence, the as yet undiscovered Kirkendall Effect was precompensated. The values of ri and r1 are therefore given by ri = 8.255 + xi and Y, = 8.255 + x,. The illustrative table below lists the position xi (mm), ri (mm), the value of ri/r1, the reported concentration (ci) in weight percent (only valid for radial analysis of data), and the corrected concentration [c'i = (ri/r1)ci] in weight percent (only valid for planar analysis of data). Similar tables can be constructed for the remaining forty-six samples. The corrected data can be used to re-evaluate the diffusion coefficients for the reported systems.

Jan 1, 1965

By J. E. McDonald, J. G. Eberhart

A model is discussed from which the work of adhcslon .tor liquid transition metals on aluminum oxide surfaces can he calculated, A close-packed (00011 oxygen surface on A12O3 is assumed with two different types of surface sites: one type involving metal-oxygen bonds and the other man der Waals into actions. The work of adhesion is thus expressed as the sum of these two bonsding free energies. Calculated works of adhesion for nickel, titanium, chromium, and zirconium on sapphire agree well with the experimentally determined quantities. The model is extentled to the calculation of the work of adhesion and shear stress required to remove a thin metal film from a sapphire substrate and is in good agreement with experimental values. The obsewed dependence of the work of adhesion on the free energy of oxide formation of the metal is shown to also provide an interpretation of the tittle dependence of thin-film adhesion. THIS paper presents a model for the type of bonding which occurs across a metal-A12O3 interface. The model is used to explain the results of two types of experiments in which such an interface exists: 1) the adhesion of thin metal films on Al2O3 substrates and 2) the wetting of A12O3 by liquid metal drops. The adhesion of thin films to various substrates has been the subject of a variety of investigations.'-' Benjamin and weaver3 and Bowie,6 using the scratch test developed by Heavens,10 studied the adhesion of metallic films to glass substrates. Their observations for noble-metal film adhesion agree well with an adhesion model involving a van der Waals type of bonding between the film and the substrate. For films of metals whose free energy of oxide formation. ?F°f, has a negative value. Benjamin and weaver3 and Bowie6 found a time-dependent adhesion with an initial value that can be interpreted in terms of van der Waals interactions but a larger terminal value which was related to ?F°f, Karnow-sky and Estill7 deposited films on sapphire at elevated temperatures and noticed no time dependence of film adhesion but a similar correlation with ?F°f. Because of the kinetic problems associated with thin-film adhesion it is desirable to examine adhesion in an equilibrium system. The wetting behavior of liquid-metal drops on Al2O3 provides such a system. Systems of this metal-ceramic type have been studied extensively.11 Humenik and Kingeryl2 have measured the wetting of A12O3 (and other substrates) by several metals and have pointed out that the wetting ability of these metals increases with increasing values of -?F°f. It is thus seen that thin-film adhesion and metal wetting on A12O3 are both related to the tendency of the metal to react with the surface oxide ions of the Al2O3 substrate and, because of this, both phenomena should be explainable by an appropriate model for the metal-Al2O3 interfacial bonding. In the sections that follow, wetting and adhesion data on A2O3 are reviewed and a model is presented by which these phenomena can be interpreted. ANALYSIS OF WETTING EXPERIMENTS In an equilibrium system involving a liquid-metal drop on a solid Al2O3 substrate, the work of adhesion, WAD, is defined by the Dupre, equation as WAD = ?s + ?L -?sL [1] where ?s and ?L are the surface free energies of the solid substrate and the liquid drop, respectively, and ?sL is the interfacial free energy. The work of adhesion is the work required to separate a unit area of the solid-liquid interface into two surfaces. The work of adhesion is usually determined from a sessile-drop experiment in which yL and the contact angle, ?, are measured. The Young-Dupr6 equation is then used to calculate WAD Wad = ?L (1+ cos ?) [2] The literature of this subject has been examined and Table I shows work of adhesion data for various liquid metals as measured on A12O3 substrates. The standard free energy of oxide formation of the metal at the temperature of the wetting experiment, ?F°f . is also tabulated in kcal per g-atom of oxygen. The data is grouped according to the gaseous atmos-

Jan 1, 1965

By K. N. Weaver

In the early 1950's the cement industry began putting a new emphasis on geology. This article points up some of the industry's raw materials problems that geologists are uniquely qualified to handle. Portland cement can be made from relatively abundant industrial minerals and rocks, and this may explain why cement producers placed little emphasis on geology during the early days of the industry. After World War 11, however, the industry began to recognize the need for geological exploration and some of the larger companies began to build a permanent geological staff. This development has its roots in: 1) The rapid expansion of the industry. After World War II and continuing into the early 1950's the demand for cement far exceeded the production capacity. This placed a great deal of pressure on the producers to enlarge capacity at their plants and to develop new sites. 2) The closing of many cement plants due to inadequate raw materials. Producers feared lack of raw materials due to inadequate exploration and evaluation. 3) An ever increasing pressure for upgrading of the quality of portland cement, necessitated upgrading the quality of raw materials. 4) The increasingly large capital investment needed to build new cement plants required a higher degree of accuracy in reserve calculation. These reasons are more or less self explanatory and will not be elaborated on. They are outlined to illustrate the probable evolution of thought among cement management to justify the development of a geological staff. In the author's personal experience the geologist must continually readjust to changing conditions within the industry. For example, cement production capacity grew so rapidly that today production is only about 70% to 75% of rated capacity (73.8% in 1963). Therefore, whereas the geologist's function during the active expansion of capacity was primarily one of exploration, one of his major functions today is the development of existing reserves. This assumes of course that reserves at existing plants have been proven to be adequate in terms of the company's reserve policy. Through the proper development of raw materials, the geologist can markedly influence quality control, production and long range planning. Examples of several of the operations of Medusa Portland Cement Co. will illustrate how proper attention to geologic detail pays off in the above areas. Because limestone is the major raw material of port-land cement, the examples will be concerned with it. DEVELOPMENT OF GEOLOGIC DETAIL One of the prime objectives of an exploration or development project should be the establishment of the stratigraphy and structure of the deposit. The basic tool for exploration and development is still the core drill, and the geologist must gain a maximum amount of information from a minimum amount of drilling. In order to obtain this objective the following is essential: 1) Adequate detailed geologic logging of cores. The core is first logged and separated into lithologically distinct units. In order to make the lithologic breaks as meaningful as possible, representative pieces of core (not all) are etched in dilute HCI. This removes the "drill polish", brings out the structure of the rock and indicates the proportion of dolomite and argillaceous material because dolomite and argillaceous material etch in relief. In this way the lithologic breaks become clearer and one gains a general idea of the chemical makeup before analysis. This method of logging lessens the probability of including two types of stone, e.g. limestone and dolomite into the same sample for chemical analysis. 2) Representative sampling for chemical analysis. After logging, the lithologic units are sampled for chemical analysis. A representative analysis can be obtained by extracting a 1-in. sample for every foot of core. For example, a lithologic interval of 10 ft to 20 ft would yield ten 1-in. samples taken at 11 ft, 12 ft, 13 ft... and 20 ft. These samples are then crushed, pulverized and split into a sample for chemical analysis. This sampling method represents a significant saving of time over splitting the entire core. 3) Preparing the core as a record. Because of the expense of storage and the difficulty of handling large amounts of core, only representative samples of each lithologic unit are saved for reference. An

Jan 1, 1965

By J. E. Harris

By elimination of other possible nucleation processes, it has been demonstrated, for commercially pure magnesium and a Mg-Al alloy, that at stresses less than that necessary for triple-point cracking creep cavities are most probably nucleated heterogeneously at second-phase particles. Evidence for the existence of such particles is presented and the role of grain boundary sliding in the nucleation process is examined quantitatively. DURING creep deformation of polycrystalline magnesium and its dilute alloys in the temperature range 0.45 to 0.7 Tm (Tm = absolute melting temperature) cavities form mainly along grain boundaries oriented normal to the stress axis and failure eventually occurs by their growth and impingement.' The possibility of low-ductility creep failure of magnesium-alloy reactor cans during service has prompted a number of studies of cavity formation in these materials.2-5 In this paper divergent theories of cavity nucleation6-10 are examined critically and conclusions drawn regarding the most probable mechanism of formation of cavities in magnesium. The paper is divided into two parts. The first section consists of the review and quantitative assessment of the possible role of grain boundary sliding in the nucleation process. In the second part an experimental program is described where an electron-microscope technique has been used to determine if second-phase particles exist in as-received commercially pure magnesium and in a magnesium alloy 1) THEORETICAL REVIEW Possible nucleation sites for creep cavities are: a) high-angle grain boundary triple points,11-14 b) subboundary/grain boundary intersections,15-18 c) ledges in the grain boundary, 19-25 d) second-phase particles. 9,26-30 Each of these possibilities is now considered with special reference to deformation of magnesium. 1.1) Triple-Point Cracking. The stroh31 condition to nucleate fracture is: " > vr [1] where ss = applied shear stress, ? = surface energy, C = shear modulus, L = length of sliding interface. This relationship is independent of the nature of the interface and it is possible to calculate the stress concentration at the end of a sliding high-angle grain boundary and thus deduce, approximately,* the minimum applied stress necessary to nucleate triple-point cracking. Such theoretical predictions for Nimonic alloys have been made by McLean13 and found to agree quite closely with the minimum stress determined by experiment. Stresses capable of nucleating triple-point cracking should also be sufficient to nucleate fracture at a grain boundary due to intragranular slip, for the lengths of sliding interface in the two cases are approximately equal. Thus the minimum stress for triple-point cracking should represent a demarcation between failure due to general "cracking" and that due to cavitation. Hauser, Landon, and Dorn32 have demonstrated that for polycrystalline magnesium in the temperature range 78° to 298°K the fracture stress is inversely proportional to the square root of the mean grain diameter. As pointed out by stroh31 this result indicates that Eq. [I] describes the fracture characteristics of magnesium at low temperatures. Heal3 has reported that for rapid deformation (112 pct hr-1) of polycrystalline magnesium the transition from cracking to cavitation occurs in the temperature range 175" to 275°C. He also presented the fracture-stress values for the same material tested under similar conditions. From Eq. [I] taking G = 1.3 x 10" dynes , ? = 600 ergs . cm-2,33 and L = 0.017 cm, a Stroh-McLean13,31 tensile stress of -266 kg. cm-2 is calculated, corresponding to a transition temperature of -190°C; this is in

Jan 1, 1965

By J. H. Brophy, A. L. Prill, H. W. Hayden

An error lzas been found in the conventional way of determining the time exponent of linear shrinkage for the solution-precipitation stage of liquid-phase sintering. Large amounts of shrinkage due to initial rearrangenzent result in erroneously low exponents and tni si dentification of the rate-controlling process. Two alternative, mathematically correct, methods of calculation are applied to existing data on Fe-Cu, WC-Co, and Tic-Ni-Mo. This results in reidentifi-cation of the rate-controlling process and somewhat better agreement with related data. In each case the solution-precipitation process is solution-controlled and not diffusion-controlled. THE liquid-phase sintering process has been the object of a considerable amount of research for many years. Linear shrinkage vs time data at various sintering temperatures have been used recently in an attempt to identify the prevailing mass-transport processes in a number of metallic and nonmetallic systems. There is an analytical error inherent in the methods previously used for handling data during the "solution-precipitation" stage of shrinkage which must be recognized before the correct rate-controlling processes can be determined. It is the purpose of this paper to show how the error has affected previous conclusions and to suggest corrections. A number of mechanisms have been proposed to explain experimental observations during sintering in the presence of a liquid phase. The earliest of these is due to Price, Smithells, and williamsl who attributed the observed growth of the solid phase to the simultaneous solution of smaller particles and growth of larger particles. From the work of Lenel et al.2,3 and Gurland and Norton4 has come the suggestion that the liquid-phase sintering process may be divided for analysis into three steps: 1) rearrangement upon formation of the liquid phase; 2) solution and reprecipitation of the solid phase in the liquid; and 3) "coalescence" or a final stage of sintering, characteristically slower than the solution-precipitation process. The sequence of steps is shown schematically in Fig. 1. Kingery5 presented a thermodynamic and kinetic analysis of the first two "stages" of the liquid-phase sintering process in which the functional dependence of lineal shrink- age on time at temperature was used to identify the rate-controlling mass-transport process. Table I summarizes the time dependences and processes considered by Kingery.5 This method of data presentation has been employed by Kingery and coworkers for Fe-CU,6 WC-Co, and a number of nonmetallic systems," and bv Whalen and Humenik for Tic-Ni-Mo and Fe-cu.8 In each of these studies, the rate-controlling step during the "solution-precipitation" stage was identified from the slope of the curve in that stage on a logarithmic plot such as Fig. 1. However, in all of the previous studies, at a certain composition, relatively large amounts of shrinkage due to rearrangement preceded the solution-precipitation stage. Under these conditions, the larger the amount of rearrangement shrinkage the

Jan 1, 1965

By Arnold M. Lansche

DOMESTIC OUTPUT of white arsenic, As2O3, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. Arsenic metal was not produced. Consumption, and Uses.-Most of the white arsenic produced in 1964 was consumed in manufacturing lead and calcium arsenate insecticides. In the 12 year period since 1951 the production of lead arsenate insecticide has varied between 7,800 tons and 4,900 tons, indicating that lead arsenate has maintained its position in competition with organic insecticides.

Jan 1, 1965

By H. H. Podgurski, Hsun Hu

Large cryslals of high-purily iron (99.996+ pcl) cannot be obtained by the usual strain-ameal technique. Repealed phase transformation by thermal cycling prior to crilical deformation improves the capabilily of cryslal growith but fails to yield satisfactory crystals. Imperfect columnar crystals can be produced by the phase-transition method. The addition of a small amounl (0.005 wl pet) of nilrogen IT was reported'-4 that for metals of very high purity the usual procedures of the strain-anneal technique fail to produce large crystals. This was eliminates practically all the difficulties in crystal growth by the normal strain-anneal procedures. An actual example is presented, showing that most parts of a strip have been converted into a large crystal by this method. The addition of nitrogen, which can be removed from iron with less difficulty, is believed to be more desirable than carbon additions for the same purpose. thought to be due to the strong tendency for recovery in the high-purity metals: hence the critically strained matrix undergoes polygonization instead of recrystallization upon annealing for crystal growth. Talbot1,2 succeeded in overcoming this difficulty by adding 0.03 to 0.04 pct C to high-purity iron before critical deformation. followed by annealing in hydro-

Jan 1, 1965