Search Documents

By Thomas J. Crocker, Galen G. Waddell, Eugene H. Skinner

This paper describes a method of measuring initial and long-term deformations which occur in the medium surrounding mine accessways, and discusses the importance of this type of measurement in assessing support-problem areas. Delineated are (1) description of the rock-deformation monitoring equipment, (2) results of two field tests which monitored rock deformation around 4-foot-diameter raise bores, and (3) a numerical-analysis (finite-element) technique to correlate theoretical with experimental results. Instrumentation developed provided the sensitivity and resolution needed to measure rock deformation around a full-scale raise bore during excavation. Results of the tests conducted at the Lucky Friday mine, Mullan, Idaho, show the relationships between (a) de- formation vs. time, and (b) deformation vs. bit progress. Based on theoretical evaluation of the initial deformation, the medium appeared to behave elastically. Using an estimated field stress of 5,500 psi and Poisson's ratio of 0.20, the gross modulus of elasticity of the rock was calculated to range from 3.15 to 6.0 x 106 psi (with one outlier which was determined to be >12 x l06 psi).

Jan 1, 1971

By Warren B. Davis

Introduction If a subject this broad were to be covered in even moderate detail, it would require a set of books about the size of an encyclopedia. Since an acceptable length for this paper is a small fraction of one book, it will have to consist of a few samples of the subjects that I think are the most pertinent to World Fossil Fuel Economics. I plan to discuss the trends in world energy demand, particularly in the U. S. and Europe; the consumption patterns and cost patterns of oil, gas and coal; the prospects of synthetics; and some of the effects of government regulation of fuel economics. World Energy Demands Fig. 1 shows Free World energy consumption by principal areas for the period from 1950 to 1970 and a forecast for the period from 1970 to 1985. These figures include only the measurable forms of energy. An example of energy consumption that is not measured is the wood a peasant might cut in the forest and bum in a fireplace to heat his home. This omission probably is a very small part of the total. This forecast is not identical with that of Wayne E. Glenn (see Page 22), but the differences in total energy consumption are not significant. The U. S. consumption, which was 55 percent of the world total in 1950, had declined to 45 percent by 1970, and is expected to decline further to 38 percent by 1985. Western Europe has consumed 28 percent of the total from 1950 to 1970 and is expected to lose share slightly between 1970 and 1985. The most spectacular gainer is Japan, which increased consumption from 2.5 percent in 1950 to 7.5 percent in 1970, and is expected to reach nearly 17 percent by 1985. The over-all Free World total has grown from 62 quadrillion Btu (equivalent to 29 million B/D of crude oil) in 1950 to 151 quadrillion by 1970, an average growth rate of 4.5 percent/year. This total is expected to grow at a rate of 5 percent/year between now and 1985, reaching 315 quadrillion Btu (equivalent to nearly 150 million B/D). Fig. 2 shows which fuels supplied this energy between 1950 and 1970, and gives an estimate of how it will be supplied between 1970 and 1985.

Jan 1, 1971

By Ian McC. Stewart

"Seam gas flow in coal mines takes place through a medium which has both capacity and resistance and can therefore be expressed in terms of the basic diffusion equation, provided that the characteristics of the system can be adequately described. It may be possible to lump the variations from point to point in a seam together as an effective diffusivity. The paper discusses the characteristic flow-time patterns for various types of openings and the particular features of coal and seam which influence the diffusivity.Two field experiments are described in which gas make to a heading and to a borehole were measured in a mine for which considerable data on coal sorption properties were available. Incremental gas flow measured from the borehole experiment predicted the actual flow from the heading measurements remarkably well. The effective permeability adjacent to the face was much higher than expected from the properties of the coal. The incremental flow measurements to a horizontal (in-seam) borehole showed a striking picture of advancing 'relaxation' behind the face which is not discernible by other experimental means."

Jan 1, 1971

By L. B. Pankratz

Low-temperature heat capacities, high-temperature enthalpy increments, and the enthalpy of formation at 298° K were determined calorimetrically for vanadium subnitride (VN0.465). The low-temperature investigation gave S°298.15 = 6.379 ±0.005 cal/deg mole, and a combustion calorimeter investiga¬tion provided ?Hf°298.15 = -31.80 ±0.60 kcal/mole. The two quantities were combined with the high-temperature data to give standard values of enthalpies of formation and free energies of formation above 298° K. These and related thermodynamic functions were tabulated to 1,800° K. Similar data are included in the range of 298° to 1,600° K for the mononitride, VN.

Jan 1, 1971

By C. L. Sainsbury

For 10 years, the author has been engaged in a program of geologic mapping of the Seward Peninsula, Alaska, for the U.S. Geological Survey. Initially, two 1:63,360-scale quadrangles were napped by traditional methods of traverses by foot and by tracked vehicle, supplemented by reconnaissance from a light aircraft owned and piloted by the author. Five summers were required to map those two quadrangles, which lie north of the tree lice in typical Arctic climate. In 1967, the project was reoriented toward the reconnaissance capping of four 1:250,000-scale quadrangles, with helicopter support to be used for cart of each of four summers amounting to about 45 hours time per support year. The light aircraft was use-,' to support the field operations. Over the year,, the aircraft was used in progressively more geologic tasks, culminating in 1970 with a successful field test of rudimentary devices made to collect soil, rock, and sediment samples while the aircraft remained airborne. Additionally, an attempt was made j- 1970 to prepare reconnaissance geologic maps entirely by the use of the light aircraft combined with foot traverses [fr??], the landed aircraft. Several such maps, prepared at the rate of about one 1:63,360-scale quadrangle per day, were checked from a helicopter by an impartial observer end were found to be sufficiently accurate for reconnaissance mapping when reduced to 1:250.000 scale.

Jan 1, 1971

By Robert M. Funk, James E. Lawver

The development of a laboratory and pilot-scale high-tension electrostatic flowsheet for the production of iron-ore super concentrates having silica contents in the range of 0.1% is presented, A variety of hematite and magnetite ores were tested with this flowsheet, and the pertinent metallurgical data are given. The applications and limitations of this process are brought out in terms of both practical and theoretical considerations. There have been many new developments in the past few years that have required mineral beneficiation engineers to consider new techniques for iron-ore concentration. Developments in iron powder metallurgy, and particularly the making of sheet metal directly from high-purity iron-ore concentrates, and the concept of using metallized pellets as a substitute for scrap in electric-furnace steelmaking have created demands for what is commonly referred to as iron-ore superconcen-trates. In most cases, specifications for superconcentrates are that they contain less than 0.1% total gangue, with some applications requiring less than 0.05% gangue. To produce these concentrates, new and modified processes are being developed, and the three methods receiving attention as the primary concentrating methods are: 1) Magnetic separation in which dry rotor-type equipment is used for magnetite and the high-intensity magnets are used for hematite. 2) Amine flotation. 3) "High-tension" electrostatic separation (or, elec-trodynamic concentration). This paper examines the high-tension electrostatic process in terms of its limitations and abilities for the production of iron-ore superconcentrates. A technically effective and simple flowsheet was developed through laboratory and 5 and 100-ton pilot-plant studies for the production of concentrates containing from 0.02 to 0.20% SiO, with iron recoveries between 85 and 90%. The process is also shown to be economically feasible. Laboratory Test Program Separation Characteristics: The suitability of the electrostatic high-tension method for iron-ore supercon-centration stems from the fundamental mechanism governing the process, i.e., particles are separated on the basis of differences in electrical conductivities. This conductivity is a characteristic property of minerals, and if the difference between the conductivities of two min- erals is great enough, then their separation can be performed by a high-tension machine. As shown in Figs. 1 and 2, the critical factor is the time necessary for the particle charge density, which is established by a corona discharge field, to decay to a level such that the centrifugal force acting on the particle exceeds its electrostatic, or image, force. At this point, the particle can leave the rotor at some trajectory and fall into an appropriate product receptacle. This decay time is directly proportional to electrical conductivity, and the process variables, such as feed rate, rotor speed, electrode configuration, and rotor composition, are selected to optimize the ability of the separator to resolve different conductivities. Table 1 lists the measured conductivities for some of the iron and gangue minerals used in developing the flowsheet. These results were obtained by using the conductivity cell described by Lawver and Wright.' The discharge curve of most minerals that lend themselves to super concentration by high-tension is so fast that the

Jan 1, 1971

By Nathaniel Arbiter

There is a history in all men's lives, Figuring the nature of the times deceas'd, The which observ'd, a man may prophesy, With a near aim, of the main chance of things. W. Shakespeare, Henry IV; Part 2 Introduction This nation's first century embraced two stages of the Industrial Revolution. During one, what had been a colonial agricultural economy began to industrialize; water power, then steam after 1794, were the energy sources; coal and iron were the essential ingredients. The second stage started after 1850; aided by rich and diverse mineral resources, the country began its transition from the Iron Age to the Age of Metals. Early civilizations had been built on stone, and fairly high levels were sustained on iron. But the spectacular advances in the past century in communication, in construction, in transportation by sea, rail, land and air, and in much that characterizes modern civilization have depended increasingly on the use of the complete metallic and nonmetallic resources of the earth's crust. Thus it was appropriate to define the Industrial Revolution as “the period during which man's relationship to natural resources became utterly changed”, 1 with minerals playing a major and indispensable role. But we are now becoming aware that the relationship of man to natural resources must change again. On every hand the dangers inherent in the contamination of land, sea and air by the wastes of civilization are becoming apparent. And from the growing realization that mineral wealth is finite must eventually come other far reaching changes in mineral use and distribution. For on the scale of centuries we cannot continue to exploit mineral resources even at present rates, let alone at expanded rates, without eventual depletion of the more abundant resources, and early exhaustion of the less abundant. In the past our problems were relatively easily met by the development of new and improved machinery and processes. But the future will

Jan 1, 1971

A predicted increase in aluminium production and the possibility of a diminishing supply of petroleum coke for anode electrodes in alumina reduction cells makes it desirable to find alternative electrode materials. Browncoal char, with a lower ash content and with an elemental purity similar to petroleum coke, was produced by leaching in hydrochloric acid, washing with water, and charring at 1,150°C. The cost of processing is estimated tobe competitive with petroleum coke.Without further processing the bulk density and real density were undesirably low, but by briquetting the coal before charring and crushing, the bulk density was improved to 92 per cent of the petroleum coke value andthe particle density was improved to 92 per cent of the density of petroleum coke by water displacement or 75 per cent by mercury displacement.Pre-baked electrodes were prepared from the char alone, mixtures of petroleum coke and char, and from petroleum coke alone, all bonded with coal tar pitch.The electrodes were tested for the usual physical properties and were evaluated for performance in a laboratory size alumina reduction cell.Electrodes based on brown coal char alone were found to be inferior in physical properties and performance, but mixtures of the char and petroleum coke, despite poorer density, electrical resistivity, and carbon consumptionon a theoretical basis, in performance tests gave up to 17 per cent better carbon consumption per weight of aluminium produced and 21 per cent better electrical current efficiency than the electrodes based on petroleum,coke alone.It is suggested that larger scale tests are warranted.

Jan 1, 1971

Esso-BHP have installed a production supervisory control system that is presently controlling the offshore oil and gas facilities on the Barracouta and Marlin platforms from an onshore master station. This control is achieved with a computerized master station onshore which uses a UHF radio system for telemetry and control.The system is designed to control, monitor, and gather data from a large number of oil and gas production platforms and has flexibility to handle future variations in operating conditions.The system will be extended to the Halibut platform late in 1970 and to the Kirlgfish platforms during 1971.

Jan 1, 1971

By Verne E. Hooker

Near-surface temperature measurements in two granite quarries show that diurnal temperature variations are significant to a depth of 1 or 2 feet, and annual temperature variations are significant to a depth of at least 25 feet. As a result, ground stress anomalies due to temperature exist near the surface, and their magnitude depends upon the time of day and the time of year. Rock stress and corresponding temperature measurements were made in one granite quarry over a rock temperature range of 33° to 81° F. Measured rock temperatures show good agreement with values predicted from one-dimensional heat flow theory. Calculated and measured stress-temperature coefficients for the two granites in this study are given. Thermally induced stress variations in near-surface rocks tested were as large as 1,690 psi from combined daily and seasonal temperature changes.

Jan 1, 1971

By J. R. Ross

Recovery of uranium from slightly alkaline mine water, available in the Ambrosia Lake district of New Mexico, was studied using countercurrent ion exchange columns developed by the Bureau of Mines. Approximately 5 million gallons of mine water containing 9 to 12 ppm U308 was treated by ion exchange using a 14-inch-diameter absorption column composed of five or six compartments each 4 feet deep. Uranium recoveries averaged in excess of 98 percent at solution flows ranging from 15 to 25 gallons per square foot per minute and resin loadings up to 3.6 pounds of U.08 per cubic foot. In subsequent tests, loaded resin was continuously eluted in a countercurrent elution column with a diameter of 4 inches and containing a bed of resin 9 feet deep. The resin was eluted to a residual loading of less than 0.06 pound of U305 per cubic foot, at a resin-retention time of 224 minutes, using only 1.9 volumes of 1.1 M NaCl-0.05 M NaHCO3 solution per volume of resin. Compared with existing ion exchange practices for recovering uranium from mine waters in the Ambrosia Lake district of New Mexico, use of these improved ion exchange contactors would reduce ion exchange resin requirements at least 70 percent and allow further substantial reductions in capital and operating costs.

Jan 1, 1971

Experimental investigations were made into the decoppering of lead, tin, and bismuth using a technique which approximates on the small scale to industrial practice.Decoppering lead with sulphur alone in the absence of tin and silver did not proceed to low copper values. With a minimum of 0·02 per cent Ag or 0·10 per cent Sn, lead was decoppered to less than 0·01 per cent Cuby stirring with 0·2 per cent S over 10 min. Decoppering of tin or bismuth proceeded rapidly to very low levels in the absence of any "catalytic" impurities, at any rate in excess of those concentrations normally encountered in commercially pure tin or bismuth.

Jan 1, 1971

By Robert M. Doerr

The research objective was to determine the effect of aluminum alloy additions on the oxidation behavior of cobalt-nickel alloys. Thirty high-purity alloys were reacted with 02 at 0.5 atm at 1,351°, 1,389°, and 1,429° K in a volumetric apparatus for about 300 min. The alloy compositions consisted of Co-Ni master alloys (0, 22, 50, 70, 91, and 100 wt pct Ni) with aluminum additions of about 0, 1, 2, 4, and 8 wt pet. Large early deviations from, or changes in, the parabolic rate constant were encountered, but in most cases, the reaction rate declined approximately in accordance with the parabolic rate law. A sharp peak in the parabolic oxidation rate constant was observed for specimens containing a to 22 percent nickel and 1 to 2 percent aluminum at 1,351° K, and the rate constants for these compositions were lower at the higher temperatures. Specimens containing 8 percent aluminum reacted far more slowly than did any of the others.

Jan 1, 1971

By Henry F. Cooper, Scott E. Blouin

Large jacking test procedures that have been applied to obtain static in-situ rock properties (Ref. 1) have shown that the in-situ rock modulus and strength can be considerably less than what would be obtained from laboratory tests on intact samples. This trend is also expected to be true for dynamic properties, but few dynamic in- situ rock property tests have been conducted. During the past several years, high explosive test procedures have been developed to simulate the airblast and direct induced ground motions (Ref. 2) produced by nuclear explosions . These test procedures load large volumes (up to 10 7 f t3) of the earth with stress levels sufficiently high to produc5 feet of particle displacement over surface areas up to l0 5 ft2. This paper discusses some of the data obtained, and the implications of these results for our understanding of the dynamic response of in-situ rock. DESCRIPTION OF TEST PROCEDURES As shown in Fig. 1, the High Explosive Simulation Technique (HEST) consists of a cavity of uniform height bounded on the sides by a soil berm, above by an overburden of uniform thickness, and below by the test bed on the earth's surface. Horizontal racks of detonating cord are placed in the cavity and detonated at one end of the test bed. This detonation produces an explosive wave that propagates across the test bed, loading the earth with an overpressure pulse that decays with time because of the compression and lifting of the overburden. Since 1964, there have been approximately 40 such tests on test bed areas ranging from a few hundred to l0 5 sq ft., simulating peak overpressure conditions between about 100 and 6000 psi and specific impulses between a few and over 100 psi-sec.

Jan 1, 1971

The addition of cement to underground backfill at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited, Broken Hill commenced in 1967. A deterioration in metallurgical performance at each concentrator occurred as a result, with increased loss of lead and zinc to residues. Investigations to determine the reasons for this problem and methods to counteract it have been undertaken. This paper outlines the effects of cement on lead-zinc beneficiation at Broken Hill and presents an interim report on attempts to overcome the metallurgical deterioration.

Jan 1, 1971

By Vasily P. Muravjev, Gennady I. Razgildeev

The theory of reliability is a powerful mathematical tool for determining optimum selection of components and application of electrical power to coal mines. In order to make this tool useful, statistical material on equipment life must be gathered and all failures carefully recorded. Statistical data can be applied to new apparatus design and can be used to determine optimum configuration of network and maintenance to reduce costs. Reference is made to underground power systems in the USSR. Technical progress in the last few years has occurred in the design and application of highly productive coal mining and transporting machinery. One of the most important problems facing mining engineers is to increase the availability of the machine to obtain higher productivity. However, machine failures and breakdowns of electrical power supply components cause serious delays in the coal-winning processes. In spite of the fact that electrical equipment and the power supply contribute only a small percentage of direct mine costs, electrical failures as well as power supply delays can result in severe indirect losses. It is necessary, therefore, to consider reliability and safety in the application of electrical equipment underground. To obtain the best results, it is necessary to investigate and evaluate the reliability of the electrical mining components (starters, breakers, motors, cables, etc.) and optimal methods for minimizing maintenance, the desired result being equipment which is efficient and safe. Electrical equipment reliability directly influences economics: the lower the reliability the more frequently failures occur, causing serious working delays and possibly huge economic losses. By the same token, while increasing the number of preventive maintenance calls per unit time might result in fewer failures, thus reducing delays, the cost of making more frequent maintenance inspections will increase; this is one aspect to be discussed in detail. Obviously, failures of identical types of electrical equipment (starters with the same current and voltage, etc.) are influenced variably by different working conditions, environments, quality of the apparatus, maintenance procedures (personnel, frequency, quality), load, and other factors. Hence, the lifetime of identical types of equipment will vary depending upon usage in terms of the foregoing factors. Thus for a given type of electrical component, these factors must be considered quantitatively; the interaction of all these factors are evaluated quantitatively by a statistical method using probability theory. Equipment reliability must be quantitatively determined from a study of equipment life, since no one laboratory test can reproduce all working conditions and environmental effects. Nevertheless, reliability theory applied to electrical mining equipment is a very powerful mathematical tool for selecting as well as evaluating certain parameters. It is necessary to select several reliability parameters so that one can obtain an expression for the total overall economic situation in terms of cost, taking into consideration damage caused by electrical equipment failure and cost of maintenance. To accomplish this result, such characteristics as apparatus lifetime, breakdown idle time, and losses (damages) can be determined quantitatively on a statistical basis. For identical electrical equipment working under similar conditions, the previously mentioned reliability factors are random variables and therefore can be characterized readily by a probability density function. Investigations carried out by the authors in the Kuznetsk Basin (Kuzbas) in West Siberia, USSR, show that the reliability factors of electrical mining equipment are well described by the exponential, normal, or Erlang's distribution in most cases. Mining electrical equipment life is well-described by the exponential law. The distribution of lifetime density is

Jan 1, 1971

By L. A. Neumeier

The Bureau of Mines evaluated the properties and anisotropy in properties of rolled Zn-Ti and Zn-1.0 wt pct Cu-Ti alloys containing up to 0.36 wt pct Ti. Finish rolling was at varied temperatures to total reductions as high as 92 pct. Alloy properties are very sensitive to various combinations of composition, rolling temperature, and reduction. Properly rolled Zn-1.0 Cu-Ti alloys are superior in strength to Zn-Ti alloys. Conditions are described that lead to best tensile properties. Creep resistance for Zn-Ti alloys decreases with increased rolling temperature when finish rolled to 92-pct total reduction: but not when finish rolled to 33- or 67-pct reduction. Creep resistance for 7n-1.0 Cu-Ti alloys improves with increased rolling temperature to about 480° F. Heavily cold-rolled Zn-1.0 Cu-Ti alloys have fine grain sizes and poor hardness, tensile, and creep properties, but high ductility. Thermal expansivity is markedly affected by the copper addition. Data show the anisotropy of tensile, creep, and thermal expansivity properties. Large idiomorphic crystallites of TiZn15 appear in both Zn-Ti and Zn-Cu-Ti alloys when more than about 0.2 pct Ti is present. A new Zn-Cu-Ti intermediate phase was also identified. Empirical equations are presented relating creep rates with major process variables.

Jan 1, 1971

A single compartment 100 A electrolytic cell charged with AICla-KCl-NaCl at 750°C was studied during an experimental campaign of 4 months. About 10 1b of aluminium were produced in continuous runs which lasted up to 1 week. The highest cathode current efficiency determined was 80 per cent. Anode current efficiency. cathode potential, analyses of melt, sublimate, and product, and reactivity of cell materials were also recorded and interpreted in terms of the role of lower valent aluminium species in the electrolysis mechanism.

Jan 1, 1971

Jan 1, 1971

By C. D. Haynes, S. C. Gambrell

The practice of roof bolting in WORLD-WIDE mining activities is very well-known, having been used extensively for over 50 years. The theory of roof bolting, however, is extremely complicated, and only recently have investigators attempted to explain the theory. Various means of stress analysis have been utilized in rock mechanics, most of which reduce rock to an isotropic, homogeneous medium that can be easily analyzed. One of the indirect research methods is the photo-elastic technique, the theory of which is widely known and needs no elaboration. This technique has been used extensively to examine the state of stress around underground openings of various shapes in certain types of strata, and under various loading configurations.'-" In-Situ Mine Roof Trusses The photoelastic technique was employed here to evaluate the state of stress above a mine opening where support is provided by the in-situ mine roof truss. This support configuration, shown in Fig. 1, has gained popularity in recent years, particularly in mines with bad roof conditions." To the authors' knowledge, no scientific determination has been made of the advantages roof trusses may offer over conventional bolting configurations comparable to roof trusses. Ordinary mine roofs usually sag or bulge downward soon after mining. Normally, after some movement the roof begins to stabilize, but the face of this bulging mine rock is usually in tension and will almost always fail unless supported. Because rock fails easily in tension, it is desirable to "preload" the roof, that is, to impress a compressive force on the mine roof to prevent bulging and subsequent tensile failure. Ordinary rock bolting installations, particularly if the bolting is perpendicular to the mine roof plane, do not produce a preloading effect. Although bolting installations squeeze the strata together and produce a beam effect desirable for support, they do not have the advantage of actual uplift. They pull down at the anchorage point with a force equal to the bolt tension which sometimes causes a separation in the plane of the anchorage detrimental to roof strength. In-situ mine roof trusses require the installation of steel tension rods in the roof of the mine much the same as conventional roof bolts, except that the rods are arranged to produce a stress pattern above the upper surface of the opening similar to that of a prestressed beam. The roof rock acts to transmit the compression force. The simplest form of truss consists of two steel rods anchored to the back of holes drilled at an angle of approximately 45 over the mine pillars. These rods are collared near the middle of the room, and the lower ends of the rods are connected by tie rods and turn-buckles. Used in this manner, a small-diameter steel rod can provide essentially the same support as a wide-flange steel beam. By tightening the turnbuckles, an uplift on the roof can be produced. Objective of the Investigation The objective of this investigation was to determine qualitatively the state of stress that exists above a mine roof after the installation of the in-situ mine roof truss vs. that of two angle roof bolts, hereafter referred to as "roof bolts," drilled and placed in the same configuration, that is, 45" above each pillar and connected together in the middle of the room by a bearing member such as a steel beam. Each state of stress was to be identified, insofar as possible, as compression or tension above the mine opening. Model Construction A photoelastic model of a mine opening was coil-structed from -in. thick PLM-4B birefringent plastic and was machined to specification shown in Fig. 2. The dimensions of the opening were chosen to simulate a width-to-depth ratio of 3 to 1. Two % -in. holes were drilled at 45" angles, as shown, to provide for the loading devices. After construction, the model was annealed at 240°F to remove stresses produced during machining.

Jan 1, 1971