Search Documents

By Wesley G. Holtz

A project to demonstrate the feasibility of retorting oil shale by the Paraho vertical retort process was carried out at Anvil Points, Colorado during 1974 to 1976. As a part of the demonstration project, laboratory and field tests were performed to determine the physical and chemical properties of the retorted shale for use in the development of eventual full-scale disposal plans. The material which exits from the Paraho retort is classified as a non-plastic silty gravel by the Unified Soil Classification System. The particles have an apparent specific gravity averaging near 2.60 and a mass specific gravity averaging near 2.00. The material can be compacted by normal laboratory and field construction methods to about 90 to 100 pounds per cubic foot dry density depending upon the degree of compactive effort applied. The addition of moisture does not improve compactibility appreciably. When high compactive effort is applied the retorted shale is classed as impervious to water flow. The compacted retorted shale exhibits shear strengths in the same order as those observed for silty gravel soils. If the compacted material is cured (long tune simulation testing) prior to strength testing considerable strength gain can be obtained from cementing action. The amount of cementing developed is dependent upon heat treatment and other operating modes of the retort.

Jan 1, 1976

By Lars G. Olavson

A prototype roof bolt which can be remotely placed by pumping has been developed by the Bureau of Mines. It is known as the "Pumpable Bolt". With the objective of field testing the effectiveness of the pumpable Bolt roof support system a mining machine was developed capable of installing Pumpable Bolts in the normal production cycle of a typical underground coal mine. The machine was built and the pumpable Bolt concept tested and evaluated as a total system in shop and mine tests. The machine was operated in the mining cycle of two mines and pumpable Bolts were installed at both mine sites.

Jan 1, 1976

By Lon A. Williams

This appendix contains drawing lists and drawings of components and assemblies designed for the prototype portable and machine mounted lighting systems per Tasks II & IV of Contract No. H0220065.

Jan 1, 1976

By Bruce E. Stauffer

The report recommends criteria for the design of safe surface mine haulage roads. Information relevant to road design at surface mine sites delineates vertical and horizontal alignment; subbase and surface materials; drainage; cross-slope, superelevation; runaway vehicle protection; and road and vehicle maintenance criteria. An appendix Is included which details the study methods used in compiling the final report information. A bibliography following the main text lists literature referenced for the report data and which is available as a valuable tool for use by individuals involved in haul road design.

Jan 1, 1976

By Lloyd A. Morley

The performance of electrical grounding systems in open-pit metal mines is evaluated, using techniques which are described thoroughly. The normal electrical distribution and grounding practices used in metallic open-pit mines are reviewed and compared with coal mine usage. The results are used to generate the included recommendations for Federal Regulations concerning open-pit metal mine grounding systems.

Jan 1, 1976

By J. L. Buckley

A survey of previous underground mine fires revealed a number of reported fires may have been caused by malfunctioning stationary electrical equipment. Therefore, an evaluation of conventional fire protection systems was conducted to determine their usefulness in the protection of this equipment. To simplify the problem and facilitate the handling of data, the under-ground mine was divided into nine work areas. Representative combustibles and associated hazards characteristic of each area were identified. Conventionally available fire protection systems were then examined and evaluated to determine engineering and cost feasibility, effectiveness and reliability for the development of fire protection guidelines which could be used within the nine areas of interest.

Jan 1, 1976

By Eugene A. Dolecki

This final report describes the work accomplished under U.S. Bureau of Mines Contract #H0242011 - "Feasibility of Automated Rail Haulage Systems in Underground Coal Mines." The report outlines the base for the development and evaluation of automated rail haulage systems in terms of the service requirements for haulage systems in underground coal mines, and of the performance of existing haulage systems. A generalized automated rail haulage system concept is defined. A safety impact analysis of automating the mainline portion of the underground system indicates a 50% reduction in injuries and fatalities. A cost effectiveness (over the total life cycle) study for the system indicates a cost benefit can be obtained from implementing an automated rail system. The design specifications for the total automated rail haulage system - including subsystems and components -are developed, and the equipment types and general design approaches evaluated, with selections outlined. A detailed conceptual design for a prototype automated system is described. Conclusions and recommendations are presented, and a program plan devised for implementing a proto-type automated rail haulage system demonstration in an operating underground coal mine by 1980.

Jan 1, 1976

By Lulie H. Crump

Salient information on reserves, production, and consumption of fuels and energy by State is summarized in this Bureau of Mines publication. Reserve and production data are shown for each of the fossil fuels (coal, crude oil, natural gas liquids, and natural gas) and for uranium. The consumption data of each of the major consuming sectors (household-commercial, industrial, transportation, electric power, and miscellaneous) are broken down by energy source (coal, petroleum, natural gas, hydropower, and nuclear). In addition, total energy consumption in the Nation in 1973 is compared with consumption in 1972 and 1974 (preliminary data).

Jan 1, 1976

By Joe Maher

[ ]

Jan 1, 1976

The applicability of borehole assaying techniques, both conventional and advanced, to orebody evaluation in the mining industry is reviewed and assessed, and the research, development, and demonstration programs necessary to apply the various logging techniques to mining are outlined. At present, the principal method of orebody evaluation in the mining industry is coring. However, coring is costly and time-consuming, and potentially great savings can be realized if all or part of d coring program is replaced by a borehole logging suite specialized to the needs of the particular mining industry. Using a set of 12 minerals, most of which are essential to the U. S. economy, an algorithm is presented for calculating the priority of developing suitable borehole assaying technology to replace all or part of the coring in each mineral industry, The priority is expressed in terms of dollars currently spent for that portion of present orebody evaluation techniques which may eventually be replaceable by in-situ assay techniques. The orebody assay requirements (grades, accuracies, etc.) of the 12 selected mineral industries, as determined from mining industry interviews and published literature, are compiled and represent performance criteria for borehole assaying instruments for the particular industry. Current logging techniques, applied chiefly in the petroleum industry, and advanced assay techniques which are or may be packageable for borehole use are evaluated to determine their performance characteristics. The performance characteristics of the various conventional and advanced techniques are then compared with the performance criteria in each of the 12 mineral industries in order to determine the potential benefit derivable from each technique. Finally, the benefit available from each technique, averaged over the 12 mineral industries, is compared with the cost of development of the technique, to determine the overall priority for investment in research to develop the technique for use in mining. The technology assessment and cost-benefit analysis shows neutron activation analysis in its various forms to have the highest priority for research and development as a borehole logging technique. Other techniques found to be promising include x-ray fluorescence, x-ray diffraction, photoluminescence (optical fluorescence), and infrared spectroscopy. Of the 12 industries considered in the study, those where the need for advanced borehole logging technology is greatest are uranium, copper, gold, and iron.

Jan 1, 1976

By Lon A. Williams

This report, authorized under Contract Number H0220065, Amendment Number Six, documents the results of an investigation of lighting system modifications and designs for working place illumination in high and low coal entries of underground coal mines. The portable and machine mounted system designs, both modified and prototype, represent a continuation of work performed under Contract Number H0111403, Amendment Number One. See the Final Technical Report dated May 26, 1972 for detailed information concerning this prior Contract. All modified and prototype systems met the performance requirements of Bureau of Mines Specification 2G, as proved by test. In addition, the systems met the requirement for illumination, as specified in the Contract and in the proposed standards which were generated in response to Public Law 91-173.

Jan 1, 1976

A compilation of papers presented at the Third WVU Conference on Coal Mine Electrotechnology in Morgantown, West Virginia, on August 4-6, 1976. Papers cover areas of electric power, electronic communications, detection and location of trapped miners, and electronic sensors and monitoring systems.

Jan 1, 1976

By William J. Douglas

This document describes the development of a conventional mining equipment data base, and an approach for conducting industrial engineering studies of arbitrary mining systems employing network techniques. Data was acquired through underground time studies. Each member of a four-man field team was assigned to a specific machine during each shift for which observations were conducted. Using digital wrist watches and networks describing the man-machine interactions, all events occurring luring the course of each shift were recorded on cassette tapes. The tapes were transcribed, coded, keypunched, and validated using computerized editing techniques. The resulting data files were processed to provide statistics relating to activity durations and event frequencies. The results were used to evaluate operator, machine, and system performance for each section which was observed. Equipment, reliability, and maintainability analyses were conducted using the industrial engineering data files in conjunction with historical information collected at the mine site.

Jan 1, 1976

This report is in fulfillment of Contract H0230031 awarded to Bituminous Coal Research, Inc., on May 23, 1973. The scope of work to be performed under this contract was divided into four phases: Phase I - Design, Phase II - Construction, Phase III - Field Demonstration, and Phase IV - Analysis and Final Report. During Phase I, an agreement was finalized with the Rochester and Pittsburgh Coal Co. for conducting field tests of the proposed shearer spray systems on a longwall panel in the company's Jane Mine in Indiana County, Pa. A drum was then designed which could be used on the Eickhoff shearer, Model EW170-L, being used on this longwall and which would utilize the following spray systems: 1. One spray nozzle located in front of each cutter bit with the jet directed at the cutting surface. 2. One spray nozzle located in back of each cutter bit with the jet directed at the back of the bit. 3. Standard Eickhoff nozzles located in a header along the drum scrolls. 4. A fixed header mounted on the shearer directly behind the drum to simulate the spray system originally used on the Eickhoff shearer.

Jan 1, 1976

By Ronald W. Stingelin

This study undertook the development and implementation of a methodology for estimating the impact of coal seam interaction on the eastern bituminous underground reserve base as published in USBM Information Circular 8655. The effects of previous mining in multiple coal seam areas on currently mined and reserve seams are predicted as a percentage coal loss by an engineering assessment model called the Coal Loss Calculation Model. The model utilizes twelve input variables easily derivable from mine maps or other existing data sources and calculates the effects of subsidence and high-stress due to remnant pillars in the previously mined seam. Extensive literature review resulted in the identification, definition, and quantification of the critical variables of seam interaction. Export opinion surveys were made of mining experts, MESA mine inspectors, and coal mine operators. Statistical analysis was used to establish the redundancy of the critical variables and to develop a total coal loss prediction algorithm. A regional analysis resulted in the production of a series of thematic maps on coal characteristics and distribution. A derivative map showing the areas of commonality within the eastern bituminous coal region served as the basis for implementation of the coal loss calculation model. The model was developed and tested using data from four coal mines in western Pennsylvania and southern West Virginia.

Jan 1, 1976

By M. B. Balachandra

A three-dimensional finite element analysis was performed of an instrumented section of a double-entry coal mine in order to provide a comparison between field measurements and existing analytic techniques. The BMINES computer code was used to perform the analysis. The sequence of excavation of the entries was considered, as well as the installation of rock bolts and cribbing during the mining cycle. The materials In the region under investigation were idealized into four rock types and coal. The rocks were assumed to be isotropically elastic, perfectly plastic. Coal was represented by an elastically anisotropic (transverse isotropy) and plastically isotropic model. A fracture yield criterion of the Coulomb form was used for all materials. The strength and stiffness of all materials were substantially reduced from available laboratory data to account for in-situ properties. Qualitative trends and stress distributions obtained from the calculation were found to be reasonable. However, computed displacements and closures were greatly exaggerated and an excessive degree of inelastic deformation was indicated in the coal, especially adjacent to the excavated faces. It was established that both these effects were the result of an excessive reduction in the strength and stiffness of the materials. The analysis underscores the need for three-dimensional calculations by identifying a number of important structural response parameters that would be either outside the scope of, or misrepresented by, two-dimensional analyses. The analysis also emphasizes the need for comprehensive and accurate measurement of material properties in order fully to exploit the power of the analytical techniques to generate reliable predictions.

Jan 1, 1976

By D. B. Lovett

The work described in this report was directed toward identifying and devising methods to minimize the previously observed variability between working level hour exposures and the alpha particle track densities resulting on Track Etch films exposed to mine atmospheres containing radon and radon daughters. The disequilibrium between radon and its daughters was shown to directly affect this Track Etch film calibration factor. The wide range of disequilibrium states possible in mine situations amply explains the variability in the previous tests. A file of published mine atmosphere composition data was compiled and was used, along with atmospheric compositions derived from several theoretical models ref the atmospheric behavior, to evaluate the variability of several dosimeter configurations and concepts. A nonlinear, iterative regression analyse; was formulated that successfully predicted working levels to within 8 to 10% from only the alpha particle activities (Rn, RA, and RaC') data such as are obtainable from Track Etch films over a wide range of disequrlibrium conditions. A model expressing atmospheric concentrations as a function of radon source strength, plate out rate factor, ventilation rate and the fractional re-entry by recoil of previously platted-out daughters was derived and used in the regression program in addition to preparing a set of reference tables and graphs showing the disequilibrium behavior of the atmosphere. Other factors that can affect the Track Etch Film response writ considered and shown to he less crutial than the disequilibrium state. The results of a series of exposures of a dosimeter concept fixture in the Denver Mining Research Center radon chamber air presented and discussed.

Jan 1, 1976

By James J. Scott

Workshops were held in eight states during the period from December 12. 1975. through June 25, 1976, under U. S. Bureau of Mines Contract to the University of Missouri-Rolla. The workshops were designed to help define the Bureau's research and development priorities. At each workshop a summary of the current Bureau mine reclamation research was presented which was followed by identification of problems associated with mine land reclamation in the state where the meeting was being held. Discussions included the seriousness of problems locally and how the Bureau could best undertake research to assist the state in solving the problems identified. Participants included representatives of state agencies, educational institutions, and companies involved in surface mining. Attendance at these workshops totaled 201 persons who displayed a wide variety of opinions and ideas as to what should be done In government research and development efforts. A breakdown of these attendees is as follows: 91 state and Federal employees; 69 mine operators, equipment manufacturers and consultants; 33 educators and researchers; and 8 others representing such varied interests as environmental and conservation groups, news media and students .

Jan 1, 1976

The Bibliographic Data Base contained in the present volume is the result of a literature search conducted as one task of the Bureau of Mines project concerned with research in borehole assay technology. The data base includes articles, symposia, books, corporate and government reports, patents, and other literature concerned with some aspect of borehole logging, from January 1969 through December 1975. Occasional updating to keep the data base current is anticipated. The remainder of the intro¬duction will be devoted to the explanation of the organization of each entry, along with the translation of terms and abbreviations used in the text. Each entry contains six sections. These include an ID code, a title, an author section, a source section, an abstract, and a descriptor section. The first item listed in an entry is the ID code. This serves to identify an entry. It consists of the first six characters of the first author's (or editor if no authors are involved) last name, along with the last two digits of the year of publication. A letter sometimes follows the year of publication to assure a unique alphanumeric code. For example, if an author named Wilson writes more than one piece of literature in a given year (for example, 1972), the ID code for the entries identifying these pieces of literature would be identical. Therefore, to allow for unique ID codes, the first piece would he identified as "WILSON 72,', the second piece as "WILSON 72A", the third "WILSON 72B", and so on.

Jan 1, 1976

VOLUME III The objective of Volume III of this report is to provide a concise review of six major types of legal constraints, controls, and regulations on surface coal mining in the United States, as of January, 1976. At the same time, an attempt is made to format the details of federal and state exploration, mining, and reclamation regulations such that point-by-point comparisons can be made and updated as revisions occur. Thus, Volume III should provide both an executive overview and a user's manual of legal controls of surface coal mining.

Jan 1, 1976