Search Documents

By W. C. Goldberg, E. M. Frizzell

Monitoring slope displacement in open-pit mines can help predict collapses and prevent serious damage, injuries, and fatalities. Early detection of movement may indicate the need to modify slope geometry, initiate dewatering if the slope is wet, or consider artificial support measures such as cable bolting. Slope monitoring at the Berkeley pit was carried out with varying degrees of intensity and continuity for about 15 years. Some of the old mine records are still intact and accessible. Slope monitoring data can therefore be collected and published for the benefit of other mine operators. Because prediction of slope failures is empirical in nature, publication of several well documented case studies will be a valuable contribution to the industry. Background - Berkeley pit Open-pit mining of copper from the Berkeley pit, located on the east side of Butte, MT, began in 1955 and ceased in 1982. During that time, about 1 Gt (1.2 billion st) of material were removed to form a pit about 1.8 km wide by 2.1 km long (6000 ft by 7000 ft) at the rim, and 550 m (1800 ft) deep as measured from the high hill on the northwest side. From the south side, the pit only measures 365 m (1200 ft) deep. The Berkeley pit was first owned and operated by Anaconda Minerals Co., and subsequently by Arco. Following its closure in April 1982, the mine began to fill with water. Washington Construction purchased the property in 1986, and Montana Resources Inc. began mining to the east of the Berkeley pit in July 1986. Numerous instances of slope failure were recorded during the course of mining and several intensive geotechnical investigations were conducted in an effort to optimize the mine design. One of the last and most comprehensive studies was initiated in 1977. For purposes of geotechnical analysis, the mine was divided into nine design sectors on the basis of geologic conditions, geographic orientation, and economic importance (Fig. 1). Only two of these sectors - the concentrator and the southeast corner - are considered here. Material properties were obtained from several studies of samples collected from the mine and adjacent areas. The slope was monitored using standard surveying techniques to record the amount of movement in an area. The

Jan 1, 1989

By Phillip M. Dight

A number of impending and actual pit wall failures have been observed and documented which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

A number of impending and actual pit wall failures have been observed and documented, which have been interpreted to initiate on newly generated structural features. This infers failure through intact rock. Failure mechanisms have been postulated resulting from circumferential stress, extensional strain and brittle flexure. These will be discussed in the context of the failures and the associated monitoring. The implications of failure initiating on ?unknown? features has a significant impact for deep open pit mines where designs are based on the expected structural regime. Being able to anticipate such failures is important for design. Equally important is management of such changes as they arise. In this context, monitoring using high resolution microseismic techniques will be discussed as a means of providing early warning of such failures.

Jan 1, 2006

By D Barclay, S Mercer, S Wright

Mine water management is often an afterthought in mine planning processes and can introduce significant risks to projects when studied as a stand alone component at a later stage in the mine design. Incorporation of a mine dewatering and pore pressure dissipation strategy in the early stages of mine planning is imperative in order to minimise constraints on the production schedule, to match designed pit slopes and maximise project value for an open cut mine option such as Olympic Dam. A risk-based mine planning approach was adopted during the project selection phase study whereby water management was introduced into mine planning, scheduling and the development of an operational strategy. Hydrological and hydrogeological studies and outputs were successfully integrated into the various iterations of the mine planning cycle during early selection phase to manage the potential water management risks associated with pit slope depressurisation and access to dry working conditions during rapid advancement of mining phases.An extensive network of vibrating wire piezometer sets and long-term depressurisation testing characterised aquifer conditions and demonstrated that hydraulic connectivity exists within the geological profile due to the presence of structures and resource drill holes which enhance vertical connectivity. This connectivity, along with underdrainage from mining activities contributes up to 100 m of depressurisation in low permeability units.A pit dewatering strategy incorporates the mine planning schedules and accounts for operational constraints as to the location and development of the dewatering wells, storages and pipelines. Numerical modelling generated a range of likely pit inflows and dewatering requirements with the average initial dewatering discharge likely to be 150 L/s and reduce quickly to 50 L/s after five years, depending on the premine schedule.Coupled hydrogeological and geotechnical assessments were also carried out as part of the mine planning cycle and indicate that successful dewatering will go a long way to reduce the pore pressures within key geotechnical units during the rapid mining phase where around 300 m of cover sequence is stripped in five years. However, the residual storage in the primary aquifer and the residual pore pressure in underlying low permeability units will need to be dissipated (in-pit horizontal holes) as the pit floor advances. Pit slope design angles are sensitive to depressurisation and dewatering and up to 70 per cent depressurisation of key geotechnical rock units are required. Whilst an accelerated program of aquifer dewatering supported by lithostatic unloading should drive rapid depressurisation in the lower permeability units, intervention is anticipated in key geotechnical units such as the Tregolana Shale and volcaniclastics. The extent of induced drainage will ultimately depend in part upon the mining rate and geotechnical stability requirements. Practical operability testing addressed the potential for operational constraints to mine depressurisation activities such as congestion and mining schedule development within the pit and identified that depressurisation drilling can be achieved even with reduced access availability. Mine operations and planning groups established design criteria and considered the likely inoperable periods following rainfall events of seven to 14 days to manage the base surge and minimise impact on production. In-pit surface water management options to minimise operational disruptions during and after significant rainfall events were estimated used a stochastic approach.

Jan 1, 2009

By D Craw, J Pope, B Peake

Southland contains over 70 per cent of New ZealandÆs recoverable coal resources, and an investigation into the potential effects of coal mining on SouthlandÆs water resources is therefore of interest. This paper investigates pit-lake water quality in relation to current mining activities within the sub-bituminous coal and lignite deposits of Southland.   Water quality data was collected from pit-lakes in sub-bituminous and lignite deposits from October 2005 to March 2006. After periods of settled weather, turbidity increased with depth at the sub-bituminous pit-lake (10 - 21 NTUs from 5 - 30 m). In the stratified sub-bituminous pit-lake in March 2006, heavy rainfall caused higher turbidity in the epilimnion than the top of the hypolimnion (20 NTU vs 13 NTU) reflecting surface water runoff (up to 1993 NTUs) and epilimnion mixing. In contrast, turbidity at the lignite sites was variable due to the shallowness of the lakes, but noticeable increases following disturbance and adverse weather were recorded. High turbidity at the sub-bituminous deposits was attributed to the presence of clay minerals such as kaolinite whereas turbidity at the lignite sites was more likely short term and a result of heavier minerals such as quartz.   Trace element concentrations at both sites were low when compared to mine waters in other coal areas in New Zealand and no samples exceeded ANZECC water quality trigger values for 80 per cent species protection. Pit-lake water pH levels were lower and more variable in the lignite deposit (4.18 - 7.30 vs 7.24 - 8.98 in the sub-bituminous deposits). In the lignite pit-lakes, higher concentrations of trace elements (eg Dissolved As - 0.034 ppm and Dissolved Mn - 1.09 ppm) and lower pH (ÿ4) were observed at the bottom of active pits compared to inactive pits. It is possible that quartz pebble conglomerates containing sulphide minerals within the lignite seams are responsible for this.   Further investigation into the mine waters, waste rock and lake sediments will help get a better understanding of the results observed and long term processes that occur.

Jan 1, 2006

By Steven R. Lowe

Construction of a pump station, consisting of an inlet chamber, wet well and pump chamber, required excavation to a depth of 9.7 m (32 ft) below ground surface and more than 7.6 m (25 ft) below the ground water table in a rural, but rapidly developing part of southern New Jersey. Private houses are located [ ] within a few hundred feet of the pump station that use shallow wells for water supply. The pump station design anticipated support of the entire pump station on shallow foundations bearing directly on the underlying natural soils. However, during construction, uncontrolled ground water flow caused ground loss and damage to the bearing qualities of foundation soils. As a result, remedial repairs were required including support of the pump station on drilled pile foundations and releveling of the pump chamber that had settled. This case study is an example of where a poor understanding of the significance of upward flowing ground water had a major impact on the cost of construction. Anticipated subsurface conditions The pump station layout is shown in Fig. 1 with the locations of two borings made prior to construction superimposed. One of the borings was located within the footprint of the deep wet well excavation. Generally, this is not advisable where a deep excavation is required below the ground water table. This is because there is a history of projects where ground water seepage, or pressure, has broken out into an excavation through an ungrouted borehole and compromised the integrity of foundation soils. Logs of the borings did not indicate that the borings [ ] were grouted upon completion.

Jan 1, 2011

By C J. Kruger, E le Roux

Anglo American Platinum has adopted a strategy of Best Practice Principles (BPP) for sampling, mass measurement, analysis and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned.The design called for the high-grade material to be crushed to 95 per cent passing 2 mm and the design allowed for a single cutter primary Vezin sampler, increments taken from a gravity flowing stream at regular intervals, whilst filling a tanker for the pneumatic offload at our base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from our smelting complex and the input to our refineries. In addition, the design incorporated the functionality to collect increments in an ‘interleaved’ fashion from the Vezin sampler for internal precision checks.The metal accounting strategy for Anglo Platinum is the ongoing measurement of all inputs, outputs and stock levels for all our operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February every year, across the smelters and refineries (at least the base metal refinery). A trend was developing in the accounting period immediately following the introduction of the new crushing and sampling facility, whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter (sender) showed an increase in physical stock compared to the theoretical stock and the base metal refinery (receiver) showed that their theoretical stock increased against their physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question and it was confirmed through the physical stock measurement results, that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream.This paper showcases parts of the process that took place to explain the poor accountabilities for the respective sites. Previous results from the sampler ratification process (of the interleaved sampling design) were analysed again, a physical inspection was carried out on the sampling system again and the sampler performance was monitored (quality control parameters) for the period.From these investigations, it was found that airflows present inside the Vezin introduced the sampling bias and a change in sampling protocol was introduced as well as physical changes to the sampling equipment were made to eliminate the airflow and thus the bias conditions significantly. The accounting period which followed, after a phased upgrading process, showed that the accounting between our smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below five per cent relative to theoretical stock).CITATION:Kruger, C J and le Roux, E, 2017. Pitfalls in Vezin sampling for finely crushed materials, in Proceedings Eighth World Conference on Sampling and Blending , pp 151–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By C. Kruger

Anglo American Platinum has adopted a strategy of best practice principles (BPP) for sampling, mass measurement, analysis, and metal accounting for more than a decade now. When new plants are designed, the most suitable sampling equipment and sampling protocols are implemented and material flows and plant layouts are designed around sampling strategies. A few years ago, a crushing plant for a high-grade matte stream was commissioned. The design called for the high-grade material to be crushed to 95% passing 2 mm, and the design allowed for a single-cutter primary Vezin sampler taking increments from a gravity flowing stream at regular intervals while filling a tanker for pneumatic offload at the base metal refinery. This was a single point of sampling and analysis that would measure the wanted output from the smelting complex and the input to the refineries. In addition, the design incorporated the functionality to collect increments in an ?interleaved? fashion from the Vezin sampler for internal precision checks. The metal accounting strategy for Anglo Platinum involves the ongoing measurement of all inputs, outputs, and stock levels for all operations for platinum group metal (PGM) and base metal (BM) content. Included are yearly stocktakes, usually done on 1 February, across the smelters and refineries (at least the base metal refinery). In the accounting period immediately following the introduction of the new crushing and sampling facility, a trend was developing whereby the absolute difference between the physical stock and theoretical stock (PGMs predominantly) increased for the two respective sites on an ongoing basis. The smelter showed an increase in physical stock compared to the theoretical stock (sender) and the base metal refinery showed an increase in theoretical stock against physical stock. Because of this anomaly, an additional stocktake was held in September for the period in question, and it was confirmed through the physical stock measurement results that the PGM accounting problem was indeed pointing towards the evaluation of the high-grade matte stream. This paper showcases parts of the process that took place to explain the poor accountabilities for the two sites. Previous results from the sampler ratification process (of the interleaved sampling design) were reanalysed, a physical inspection was carried out on the sampling system again, and the sampler performance was monitored (quality control parameters) for the period. From these investigations, it was found that airflows inside the Vezin introduced the sampling bias. A change in sampling protocol was introduced, as well as certain physical changes to the sampling equipment, to eliminate the airflow and thus the bias conditions significantly. The accounting period that followed the phased upgrading process showed that the accounting between the smelter and base metal refinery had been restored to within statistical limits (difference between physical and theoretical stock below 5% relative to theoretical stock). Keywords sampling, metal accounting, Vezin sampler, sampler bias.

Jan 1, 2014

By J. Pohlig

It is with more than ordinary pleasure that I have complied with the request of the President of the Verein Deutscher Eisenh?tten leute, to read before this meeting and in this country a paper on a system of transport by wire ropeways which, during the past twenty years, has advanced with rapid strides in Europe, and more partic ularly in Germany. America, with its immense network of railways and water communications, should offer peculiarly favorable oppor tunities for the introduction of these ropeways as feeders, more par ticularly in the mining districts, where, as in Europe, a hilly or mountainous region frequently opposes serious obstacles to the em ployment of surface railroads. The importance of the aerial ropeway as a factor in the develop ment of mineral resources deserves the consideration of every mining engineer. As a case in point, the rich iron-ore of the sierra de Bedar in southern Spain, would probably remain untouched to this day but for an aerial ropeway, 15.6 km. (9 3/4 miles) long, which con nects the mines with the shore of the Mediterranean near the town of Garrucha, affording cheap carriage to the nearest shipping point. A railway would have cost about $480,000 (£100,000), but such a heavy outlay would have more than absorbed all prospective profits on the sale of ore. As the aërial ropeway could be built for a little more than one-fourth of that amount, or $124,800 (£26,000), its erection furnished the successful solution of a profitable mining enterprise. This line has been in satisfactory operation for over two yearn; its details will be referred to later. But beside their importance as feeders, ropeways are valuable as a means of conveyance between works and distant warehouses, and between separate buildings in the same works. Their rapidly spreading introduction for such purposes indicates how keenly the necessity of effecting economies is felt under the stress of an everaccentuating competitiop.

Jan 1, 1891

By A. Thielen

In experiments for the production of steel the principal problem has always been the introduction into, or removal from, the iron of a definite quantity of carbon. Although the solution of this problem had engaged a more or less blindly and empirically directed effort for a long time, it was only with the development of analytical chemistry that the rôle which carbon plays in the constitution of steel was disclosed in its full significance, and that many of the problems confronting the steel-maker were thereby more clearly defined than before. For a long time, and to a certain extent even to this day, the percentage of carbon in steel has been the controlling means of deter mining its quality and hardness. In many cases the percentage of carbon alone has been relied on for judging large consignments, such as the large deliveries of wire-billets and blooms to America during the past twenty years; and though to-day the influences of the other constituents are recognized and many other considerations are taken into account, and though, moreover, some special steels, such as the Hadfield manganese steel, apparently dispense to a certain extent with the assistance of the carbon, yet fix our Bessemer, Thomas, Siemens and crucible steel the carbon still remains one of the most important constituents, and I venture to say it is indispensable. In order to produce in the Bessemer converter a steel of a certain required percentage of carbon, two methods, as is well known, present themselves. By the one the decarburization process is stopped when the desired carbon limit in the bath has been reached ; by the other the bath is completely decarburizecl, and then a calculated amount of carbon added in the form of spiegel, ferro manganese, etc. In Germany the latter method only was adopted, and it was retained when the Thomas-Gilchrist process for the production of low-Phosphorus steel from high-phosphorus iron eame into use, since from the nature of the new process complete decarburization is neces-

Jan 1, 1891

By Joseph W. Roe

MaNY questions arising in the work of the mining engineer may be solved quickly and with suffcient accuracy by the methods of descriptive geometry; but, unfortunately, this subject is more often considered from a mathematical view-point than as an effective tool for solving practical problems. Some of the principles involved are merged into the ordinary operations of mechanical drawing, and are used unconsciously by the engineer in his every-day work. The rest are stowed away on the book-shelf with his forgotten or rarely-used college text-books. One reason for this condition of " innocuous desuctude " may lie in the uifortunate and often cumbersome notation which it has been found necessary to introduce. If some of these principles can be recalled to the engineer's attenti011 in terms of' every-day use they may prove of practical hearing. Recently, in talking with several mining engineers, I used some of the drawing-room methods of a machine-designer, to the evident surprise of those around me. These men were perfectly familiar with the methods, but their application to mining-work had not occurred to them. At their suggestion the present paper is offered, not in ally way as a treatise, but merely to suggest a certain point of view, in hope that it may lead others far more familiar with mining-problems to pursue the subject further. I. To Find the Strike. As the simplest and most fundamental problem, let it be required to find the strike of a vein when the location and elevation of three points on the outcrop are known. It mill be assumed for the present that the rein is a plane.

Jan 1, 1911

By Millard K. Shaler, Sydney H. Ball

During the past 50 years the attention of mining-men has been turned to Africa, and within the past decade prospecting-expeditions sent into Central Africa have resulted in the open-ing-up of several mines. Having recently spent two years in the Belgian Congo for the Societe Internationale Forestiere et Miniere du Congo, it is our purpose to outline briefly the mining-conditions in that part of Central Africa. Before it became, in 1908, a Belgian colony, this region was known as the Congo Free State. 11. Location and Area. The Belgian Congo lies in southwestern Central Africa, west of the continental divide, as illustrated in Fig. 1. It has a coastline of but 20 miles on the Atlantic, but widens rapidly eastward to points 5 north and 14 south of the equator. Its area is 908,000 sq. miles, which is almost one-quarter that of the United States and Alaska, or more than one and one-half times that of Alaska. Stated in other terms, its area is nearly one-third that of the United States, exclusive of Alaska and the insular possessions, or more than that of all the United States east of the Mississippi river. III. Topography and Drainage. From north to south, Africa is made up of three topographic elements: 1, the Atlas mountains, a highly-accentuated region

Jan 1, 1911

By Wilhelm Borchers

In all special branches of the chemical and metallurgical industries, in which large electric furnaces became necessary for carrying out new processes or for the improvement of old ones, the development of the electric furnaces took place on much the same lines. The endeavors to make a success of a new idea brought forth many ingenious designs, which, however, almost without exception, furnished the proof that the safest and shortest way to practical success is the utmost simplicity of construction of the necessary apparatus. Our knowledge of the qualities of materials for building electric furnaces and of the constituents of the furnace-charges, especially their electric conductivity and their chemical affinity towards one another at high temperatures, is still far from being complete, and from this fact we must conclude that the smaller the number of elements in the construction of a furnace, the fewer the number of unreliable factors both in the construction and in the operation of the electric furnace. This conclusion deserves special attention when an electric furnace for making steel has to be chosen from the constantly-growing number of inventions, inasmuch as the chief constituent of steel, the element iron, is a substance which in its liquid phase has so great an affinity for those elemen'ts which are to be removed from the charge, that it is very difficult to comply with the following conditions: 1, to heat the refining-slag to the highest point of its chemical activity ; 2, to prevent the iron from entering the slag, or, where this cannot be done, to make it enter so that it finally appears in the end-product

Jan 1, 1911

By A. Eilers

THE telluride of gold and silver, the " Tellurgold-silver" of Hausmann, and " Petzite" of other mineralogists, has been found in so few localities, that a late discovery of the mineral in a new locality may not be uninteresbing. So far this mineral has been found in Europe only in a few mines in Transylvania, and in Hungary; and in the United States in the Stanislaus Mine, in Calaveras County, California, in the Golden Rule Mine, Tuolumne County, California, and in a mine in Montana, the precise locality of which I have forgot, ten. The new locality referred to is at the Red Cloud Mine, Gold Hill District, Boulder County, Colorado.

By E. V. d’Invilliers

The position of these magnetic ore-mines, with reference to the county-seat, is shown in Fig. 1. They are situated on the south margin of the Great Valley, five miles south of Lebanon, and about midway between Reading on the Schuylkill River and Harrisburg on the Susquehanna River, in three prominent, contiguous hills, standing in front of the Mesozoic red shale arid sandstone hill country of northern Lancaster and southern Lebanon counties, and overlooking the great limestone plain to the north. The three hills, named respectively Big, Middle, and Grassy Hills, and separated from each other by two branches of Furnace Creek, range in a nearly east and west direction for a distance of about one mile. Their summits are respectively 870, 715, and 700 feet above tide. The railroad line opposite the base of Middle Hill is 575 feet above tide at Cornwall and 471 feet at Lebauon. These features are all distinctly illustrated in the contour-line map accompanying this paper, but are made still more clear in the relief. map, Fig. 2, comprising, as it does, about six square miles of territory contiguous to the ore-mines. This is a photographic plate of a model made by Mr. A. E. Lehman, from surveys of my own and Mr. W. F. Shunk. The model was built in layers of cardboard, each layer representing one 10-foot contour-carve line. The scale was the same as the original map, 400 feet= 1 inch, without any vertical exaggeration. The lowest contour-line is 530 feet above ocean level; the highest, 1075 feet. The center of the model was made the focusing-point of the view, which was taken—according to scale—51/2 miles north from and 24 miles above the focusing-point, looking southward. When first mined in the last century these hills exhibited smoothlyrounded surfaces, composed of soft weathered ore of great parity, beneath which lay the great mass of hard ore, constituting the whole

Jan 1, 1886

By Charles E. Wait

It is said by some that the occurrence of a deposit of sulphide of antimony in Southwestern Arkansas has been known for fifteen or twenty years. Whether or not such is the case I am not prepared to say, but I am not able to find any record of such a discovery, or any analysis of antimony ore obtained from that section, published at so early a period. The present discoveries, that seem to be attracting some attention, date back to the winter of 1873-74. At that time a vein of ore was found by Mr. Robert Wolf, in honor of whom the vein was named, and still is called, "the Wolf lode." At the time of the discovery the ore was unknown to the prospector, and its composition was not thoroughly understood in that locality until samples were sent to several analytical chemists, who pronounced it sulphide of antimony—stibnite. Since the discovery of this ore there have been three mines opened, and a number of interesting minerals of the antimonial series have been found. I have had an unusually good opportunity to collect specimens from these mines; and it is owing to the constant inquiry concerning the character of these ores that I have collected for publication the results of quite a number of analyses, sufficient I trust to clearly point out their composition. This is one of the few localities in the United States where antimony ore is found in workable quantities ; I say workable quantities, because two different shipments of ore have been made to English reduction works, and in both cases excellent returns were made. The discovery of these deposits will, it is hoped, give rise to a prosperous and remunerative industry at no distant day, and when fully developed they may yield ore in sufficient quantity to supply the regulus for the home demand, thus adding wealth not only to those interested, but also to the State of Arkansas. The three mines are situated in the northern part of Sevier County, and may be reached by the St. Louis, Iron Mountain and Southern Railway to Fulton, thence by wagon-road to Columbus, Nashville, Centre Point, and to the mines. During most seasons of the year the

Jan 1, 1880

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001

By Robert Labbe

The final tunnel lining for this project involved pumping vast quantities of concrete over large distances under the extremely busy streets of lower Manhattan. Approximately 68,000 cubic meters (89,000 cubic yards) were pumped from various locations over 152 meters (500 feet) below ground (Figure 1) to create nearly 14.5 kilometers (9 miles) of 3.05 meter (10 foot) diameter tunnel. Total distances pumped exceeded 1,645 meters (5,400 feet) horizontally after a vertical difference of over 152 meters (500 feet). The urban setting of the operation, coupled with the long distances over which concrete was pumped, created many problems which had to be dealt with along the way. A three-shift labor operation was implemented to allow sequential pouring of tunnel sections nearly every day. The fine tuning of the mix design was critical to make this operation successful.

By S. Rajendran

The area of the Exclusive Economic Zone (EEZ) of India is about 2.014 million km2 and the resource evaluation of placer deposits is one of the objectives of Government of India. Placers are detrital metallic minerals found on beaches and in the near shore areas. Quantitatively more important are placer deposits of light heavy minerals such as zircon, ilmenite and rutile. Rivers and other drainage channels are the main carriers of the placers which contain heavy minerals like magnetite, ilmenite, garnet, zircon, monazite, rutile etc. The present beach as well as part of the shelf was land during Pleistocene as a result of the world wide lowering of the sea levels. The coast line shifted a number of times. Hence, the heavy mineral placers on the beaches are expected to extend to offshore areas chiefly with Pleistocene lowered sea level strands. India has extensive deposits of heavy mineral placers along the beaches. Placer deposits of heavy minerals occur in discontinuous patches on the beaches along many parts of the east and west coasts. Along the central west coast of India (12??N - 19? N lat.) the placer containing 14 - 17% ilmenite form an estimated reserve of 4 million tons. On the Ratnagiri coast of Maharashtra, the proportion of heavy mineral varies between 54 and 70% in the bulk samples, consisting mainly of 14 - 39% magnetite and 16 - 30% ilmenite. The National Institute of Oceanography (NIO) surveys show that the sediments off the central west coast consist largely of silty sand, sand silt and clay. The core samples show that a reddish brown clay overlay olive gray clay which in turn overlay heavy mineral rich sands. The heavy mineral concentration ranges upto 90% and has mainly ilmenite and magnetite with minor quantities of apatite, rutile, zircon, kyanite etc. Siddiquie et al. reported 42 - 75% TiO2 in the ilmenite.

Jan 1, 1998

By D. E. Ranta, Stephen W. Thomas, Clancy J. Wendt

One of the most difficult tasks associated with placer mining is the sampling of the deposit. More placer projects have failed due to inaccurate assessment of the reserves than to any other reason. Within the realm of placers, those containing valuable minerals with a high unit value are more difficult to sample than those with larger bulk, lower unit value minerals. Some items to consider when sampling a placer deposit are as follows: A. A relatively large sample is needed for accurate valuation of the ground being tested. Placers are composed of many sizes of gravel which makes a representative sample difficult to obtain. B. When sampling placers for high unit value minerals such as gold, any error in mineral content of the sample will be magnified in the calculation of reserves. C. Values are usually erratically distributed within the gravel mass. Therefore, some placers with a more uniform value distribution may be adequately assessed with a minimum number of samples whereas a deposit with a highly erratic distribution of values may not be adequately sampled regardless of how many samples are taken. D. The investigation of a placer deposit should be made by, or be under the direction of, a person experienced in the art of placer sampling. F) During a sampling program, items that must be observed and noted in addition to the sample size and valuable mineral content should include boulder size and number, clay content, bedrock conditions, water, frozen ground, false bedrock, and any other physical characteristics that would affect mining of the deposit.

Jan 1, 1992