Search Documents

By H. B. Smith, B. Egeberg

Britannia metal is a white alloy consisting primarily of tin and antimony, the tin greatly predominating. The alloy usually contains a small amount of copper and occasionally very small amounts of one or two other metals, such as bismuth, zinc, and lead. It is capable of being cold-rolled, it takes a high polish, and it is fairly noncorrosive; properties which make it a popular metal for many household and traveling utensils. Britannia metal is similar in many respects to pewter and has largely replaced pewter in the arts, but it should not be confused with that alloy, because pewter is essentially a tin-lead alloy, while Britannia is a tin-antimony alloy. In view of the fact that so little has been published concerning Britannia metal, the authors feel justified in presenting the results of their investigation, particularly since the behavior of this alloy under cold rolling and heat treatment differs so greatly from that of other metals and alloys. The old craftsman, engaged in the making of ornaments or tableware, heated the cold-rolled sheet metal or his finished product to a straw color corresponding to about 375" I?., claiming to produce thereby a harder and more rigid article. The fact that possibly led him to this heating was that a reheated article or sheet made from Britannia metal has a distinct metallic ring when struck a sharp blow, whereas an unheated article or sheet has a leady, dead note. No doubt he has associated the metallic ring with a greater rigidity and strength, and justly so, as will be seen later. The approximate analysis of the metal we investigated was 91 Sn, 7 Sb, 2 Cu, and the molten metal was bottom-poured into an iron mold yielding an ingot 7 3/4 in. wide by 11 in. long and % in. thick, the casting temperature being 800" F. The ingot was cold-rolled to a sheet 0.032 in. thick, sufficiently large samples for experimental purposes being cut from the sheet at intermediate stages. The samples were all tested for hardness with scleroscope and Brine11 machine, then heated to 212" F. for 30 min., and again tested after cooling to room temperature. The same samples were heated successively at 300°, 400°, and 440" F., followed

Jan 1, 1929

By E. M. Wise

THe properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. General Requirements In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should he good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depi1atories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 Ib. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800" and 1200" C. Colored Golds The popular green and yellow golds are based on the gold-silver-copper alloys; in some cases modified by the introduction of zinc to improve the casting properties and to alter the color, and nickel to increase the strength. The properties of the Au-Ag-Cu system have been the subject of a very thorough investigation by Jänecke,l Sterner-Rainer12 and Carter."

Jan 1, 1929

By E. M. Wise

THe properties required of gold alloys for jewelry are not well standardized, due in part to problems peculiar to certain branches of the jewelry industry, in part to the individual preference of the fabricator and to his willingness to cope with certain difficulties in manufacture, which arise with the use of certain alloys. General Requirements In general, the properties desired may be classed as follows: 1. Color should conform to the dictates of good taste and smart style. 2. Corrosion resistance and tarnish resistance should he good. This is to a considerable extent determined by the carat. Resistance to such corrosive agents as mercuric chloride as well as certain depi1atories is unreasonable to expect and difficult to meet. 3. Strength and hardness must be adequate to maintain the delicate contours of finely modeled jewelry. 4. Wear resistance must be great enough to resist abnormal wear, such as is encountered by a wedding ring in a lifetime of wear. 5. Ductility must be sufficient to permit the fabrication of drawn shells, tubes and difficult shapes. Material having a yield point of not less than 60,000 lb. per sq. in., an ultimate strength of 100,000 Ib. per sq. in., and an elongation of 40 per cent. is desirable. 6. Melting point should be between 800" and 1200" C. Colored Golds The popular green and yellow golds are based on the gold-silver-copper alloys; in some cases modified by the introduction of zinc to improve the casting properties and to alter the color, and nickel to increase the strength. The properties of the Au-Ag-Cu system have been the subject of a very thorough investigation by Jänecke,l Sterner-Rainer12 and Carter."

Jan 1, 1929

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By David Sinclair, Philip B. Bucky

The dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests. § None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I The Photoelastic Method The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. General Explanation The stress at any point 0 in a structure (Fig. I), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.' To fully identify the stress, the values of P and Q and their directions or angle F must be known.

Jan 1, 1940

By David Sinclair, Philip B. Bucky

The dimensions and shapes of mine structures may at present be determined by (1) field experience, (2) structural calculations, and (3) barodynamic tests. § None of these, however, provide information as to the stresses, their direction and distribution in a mine structure. For the design of pillars, the placing of openings relative to working places such as gangways, haulage levels, etc., this information is desirable. Photoelastic methods provide this and, while relatively new, their application in all engineering fields is assuming increasing importance. This paper, therefore, will present the method with a few applications to mining, and with sufficient reference for further study by the reader. PART I The Photoelastic Method The photoelastic method of stress measurement determines the stress distribution in a two-dimensional model by optical means. It makes use of the fact that when a piece of isotropic transparent material, such as glass, celluloid, or Bakelite, is stressed and viewed in polarized** light a picture is seen which indicates by its color bands of light, or fringes, the magnitude of the stresses, their direction and their distribution. General Explanation The stress at any point 0 in a structure (Fig. I), may be resolved into two components, P and Q, each a pure tension or compression, at right angles to each other, called principal stresses.' To fully identify the stress, the values of P and Q and their directions or angle F must be known.

Jan 1, 1940

By Thomas Fraser, Alvaro Abreu

The work described in this paper was carried out under the sponsorship of the Foreign Economics Administration and in cooperation with the Departamento Nacional da Produggo Mineral, Rio de Janeiro. The project was undertaken to obtain complete data on the variations in washability of coal to be used for coke manufacture in the steel industry and to determine the economy of preliminary hand-sorting operations. The coal-producing industry of Brazil is in that pioneering stage in which operating practices and methods are just being developed. Increased wartime demand for fuel, coincident with a drastic curtailment of foreign supplies due to lack of shipping facilities, has put a tremendous pressure on the national industry to furnish more coal. Under this incentive, production facilities are being -expanded- and new methods of operation are being tested. Such changes are being developed both by improvement of existing methods that originated in the field and by adaptation and modification of methods introduced from the United States and Europe. These mining conditions and mining practices in Brazil are typical of what the American mining engineer will find in many instances when he goes pioneering into the developing coal fields of the Southern Hemisphere. The producing coal fields of Brazil are all in the southern states of that country. The coal measures are in a band roughly paralleling the coast and extending in a generally southwesterly direction from northern Sao Paulo through the states of Paraná, Santa Catarina and Rio Grande do Sul to near the Uruguayan border in the vicinity of Bajé. The accompanying map1 (Fig. I) shows the general location of these fields and also the principal routes of movement of both national and imported coal in a late pre-war year (1940). Statistical data on production by states up to that year are given in Table I. Rio Grande do Sul is still the largest producer among the coal states; but wartime

Jan 1, 1947

By Alvaro Abreu, Thomas Fraser

The work described in this paper was carried out under the sponsorship of the Foreign Economics Administration and in cooperation with the Departamento Nacional da Produggo Mineral, Rio de Janeiro. The project was undertaken to obtain complete data on the variations in washability of coal to be used for coke manufacture in the steel industry and to determine the economy of preliminary hand-sorting operations. The coal-producing industry of Brazil is in that pioneering stage in which operating practices and methods are just being developed. Increased wartime demand for fuel, coincident with a drastic curtailment of foreign supplies due to lack of shipping facilities, has put a tremendous pressure on the national industry to furnish more coal. Under this incentive, production facilities are being -expanded- and new methods of operation are being tested. Such changes are being developed both by improvement of existing methods that originated in the field and by adaptation and modification of methods introduced from the United States and Europe. These mining conditions and mining practices in Brazil are typical of what the American mining engineer will find in many instances when he goes pioneering into the developing coal fields of the Southern Hemisphere. The producing coal fields of Brazil are all in the southern states of that country. The coal measures are in a band roughly paralleling the coast and extending in a generally southwesterly direction from northern Sao Paulo through the states of Paraná, Santa Catarina and Rio Grande do Sul to near the Uruguayan border in the vicinity of Bajé. The accompanying map1 (Fig. I) shows the general location of these fields and also the principal routes of movement of both national and imported coal in a late pre-war year (1940). Statistical data on production by states up to that year are given in Table I. Rio Grande do Sul is still the largest producer among the coal states; but wartime

Jan 1, 1947

By C. C. Wright, R. J. Day

Although data on the exact tonnage of recoverable coal silt are not known, the quantity produced in 1943 was estimated to be over five million tons for the anthracite region of Pennsylvania alone. Since that time the recovery of the No. 5 buckwheat size previously included in silt estimates has increased greatly thus reducing the total silt tonnage. As a compensating factor, however, the methods of recovering silt previously escaping into the rivers and streams have been markedly improved so that the net figure may not have changed materially. Comparable estimates for bituminous coal are lacking, but undoubtedly the silt represents a significant tonnage. With the trend toward increased wet cleaning of the smaller sizes of bituminous coal, it is to be expected that even greater quantities of silt will be available in the future. The raw silt from anthracite collieries usually contains a high mineral matter content, but technological developments in fine coal cleaning have been making rapid advances and it appears probable that more extensive use of these methods will be employed in the near future. Bituminous coal silt in many instances contains a similar high mineral matter content. As with anthracite silt, however, the cleaning of this material, where necessary, appears both technologically and economically feasible. With a view to upgrading the size and value of silt, considerable laboratory and pilot plant work has been conducted by a number of organizations on what is commonly known as pelletization. Actually the process is one of extrusion in which the moist silt is extruded from a die in the form of rods, which usually break into relatively short lengths—a few inches long—as they fall from the die. Fig I is a photograph of some extruded 3/8-in. diam pellets and of the anthracite silt from which they were produced This technique of producing larger sized material from fines is by no means new, having been used extensively by the industrial carbon and clay industries for years.' The application of the process to coal silt appears, however, to be relatively new. The first major program of investigation dates back only to July 1945, when a group of engineers representing the Anthracite Institute, The Pennsylvania State College and the J. F. Pritchard and Co. conducted preliminary tests on the extrusion of anthracite silt at the Floridin Co. plant at Warren, Pa. Since that time these three organiza-tions—individually, together, and in cooperation with other interested groups— have actively pursued work on various phases of the problem. Much of the early history and details of the laboratory and pilot plant work by the Anthracite Institute, has been reported by Mulcey and Eckerd.2 It is the purpose of this paper to report additional information on the process, especially with respect to the factors influencing the quality and use properties of the product, and the current develop-

Jan 1, 1949

By Julian M. Avery

In its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all ecorlomy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss call be successfully attacked by increasing the over-all pressure; i.e., the "top prcssure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity. In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

By Julian M. Avery

In its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary purpose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by combustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all ecorlomy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the efficiency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss call be successfully attacked by increasing the over-all pressure; i.e., the "top prcssure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity. In a broad sense, the suggestion of pressure operation of the pig-iron blast furnace is not new, for operation under moderately increased over-all pressure was suggested as early as 1871, by no less an authority than

Jan 1, 1938

By Alwyn Birchmore Cox, Ian William Wark

In defending the chemical theory of flotation, Taggart, del Giudice and Ziehl have criticized1 the views of those who prefer to attribute the effects of certain flotation agents to adsorption. Perhaps with some justification, they describe the latter term as the "haven of refuge of writers lost in a morass of shaky experiment and muddy thinking." We prefer to regard it, however, as a haven of refuge for writers who seek a conventional term to describe the formation of films of flotation reagents on solid surfaces, because in many cases it is not yet possible to specify the forces that hold them there. Originally, as Taggart and his associates state, adsorption connoted a concentration difference and nothing more. In recent years, workers in the field of surface chemistry have tacitly added other meanings, and they now speak of orientated adsorption of unimolecular films on a solid sub-strate, of chemi-adsorption, and of exchange adsorption. Thus the term adsorption may connote simply the Gibbs layer of excess concentration at the surface of a solution, or a unimolecular film at the surface of a solid. Perhaps this has led to the misunderstanding of Taggart, del Giudice and Ziehl concerning the relationship between surface tension and adsorption at solid surfaces. The change in "surface tension" accompanying adsorption at a liquid surface can be used as a measure of the adsorption, and the Gibbs equation as quoted by these authors correlates these two conceptions. But, to correlate two conceptions docs not necessarily imply an attempt to explain either, although sometimes such an "explanation" is carelessly inferred. Use of "surface energy per unit area" instead of the numerically equal but more difficult and less definite conception of "surface tension per unit length " would lessen many of the present difficulties. (Compare with Adam.2) At interfaces involving a solid phase, neither '" surface tension " nor " interfacial tension "can have any meaning, but the conception "interfacial energy per unit area" call be understood by anyone who is familiar with the concept of free energy. While it is true that surface energy cannot be directly measured at a solid surface,

Jan 1, 1939

By Ian William Wark, Alwyn Birchmore Cox

In defending the chemical theory of flotation, Taggart, del Giudice and Ziehl have criticized1 the views of those who prefer to attribute the effects of certain flotation agents to adsorption. Perhaps with some justification, they describe the latter term as the "haven of refuge of writers lost in a morass of shaky experiment and muddy thinking." We prefer to regard it, however, as a haven of refuge for writers who seek a conventional term to describe the formation of films of flotation reagents on solid surfaces, because in many cases it is not yet possible to specify the forces that hold them there. Originally, as Taggart and his associates state, adsorption connoted a concentration difference and nothing more. In recent years, workers in the field of surface chemistry have tacitly added other meanings, and they now speak of orientated adsorption of unimolecular films on a solid sub-strate, of chemi-adsorption, and of exchange adsorption. Thus the term adsorption may connote simply the Gibbs layer of excess concentration at the surface of a solution, or a unimolecular film at the surface of a solid. Perhaps this has led to the misunderstanding of Taggart, del Giudice and Ziehl concerning the relationship between surface tension and adsorption at solid surfaces. The change in "surface tension" accompanying adsorption at a liquid surface can be used as a measure of the adsorption, and the Gibbs equation as quoted by these authors correlates these two conceptions. But, to correlate two conceptions docs not necessarily imply an attempt to explain either, although sometimes such an "explanation" is carelessly inferred. Use of "surface energy per unit area" instead of the numerically equal but more difficult and less definite conception of "surface tension per unit length " would lessen many of the present difficulties. (Compare with Adam.2) At interfaces involving a solid phase, neither '" surface tension " nor " interfacial tension "can have any meaning, but the conception "interfacial energy per unit area" call be understood by anyone who is familiar with the concept of free energy. While it is true that surface energy cannot be directly measured at a solid surface,

Jan 1, 1939

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By V. H. Whihelm

Since 1935 California has enjoyed a remarkable cycle of discovery, which has placed the state in a very satisfactory position in regard to oil reserves. Most ol the geophysical plays have been drilled and it is possible that new discoveries must be made by the application of careful geologic and stratigraphic studies. During 1940 only one new field was discovered, which, although not of major importance, may lead to additional discoveries. During the year, 113 wildcats were drilled. New discoveries, extensions and a reappraisal of discoveries made in 1939 will not approximate over 50,000,000 bbl., as against an estimated withdrawal during the year of 224,000,000 barrels. Demand in terms of crude for 1940 was 632,000 bbl. per day as against 626,000 bbl. per day for 1939. Demand for gasoline was the same as in 1939, but the demand lor fuel oil increased 3.8 per cent. Compared with 1939, Japanese shipments decreased from 75,786 bbl, per day to 61,000 bbl. per day, but the balance of Pacific foreign shipments increased from 59,409 bbl. per day to 61,304. Total with-drawals from storage during the year will approximate 7,000,000 bbl., almost all of which is fuel oil. Drilling activity was slightly greater than in 1939 and accounted for 890 new producing wells as against 851 for 1939 (Table 3). Production averaged 611,900 bbl. per day as compared with 614.,842 bbl. per day for 1939. The productive acreage figure of the state was increased by 4000 through discoveries and extensions. New Discoveries Los Angeles Basin District Del Vdle Field.—Northwest of Newhall, where the first oil well in California was drilled, R. E. Havenstrite completed his Lincoln No. I well, flowing 390 bbl. of 50" gravity oil together with 7000 M CU. ft. of gas. Later the well was recompleted, after cutting off the gas, for 950 bbl. of 34" gravity oil. The type of structure from which this production is coming is a plunging anticline, complicated by faulting. The Lincoln No. I well uncovered approximately 180 ft. of net sand. This field contains a gas cap and its indicated productive area approximates 500 acres. An intensive wildcat drilling campaign is expected during this coming year in the district in the vicinity of the Del Valle field. Extensions and Deeper Sand Developments Los Ange1es Basin District Athens Field.—On the northwest plunge of the Athens structure, the Thorley Oil Co. completed its No. 12-1 well, flowing 250 bbl. of 3 2" gravity oil from a depth of 8097 ft. The area in which the well is located is complicated by faulting and it is impossible at this date to determine the importance of this deep-zone discovery.

Jan 1, 1941

By V. H. Wilhelm

The trend initiated in January 1936, of stabilized gasoline prices, increased demand and extraordinary drilling activity, continued in California during the year 1937. Crude prices were maintained during the year at the highest level since September 1930. Wildcat activity with resultant new discoveries and development of proven acreage were greater than in any year since 1928. Many fields in California in former years have been produced at full capacity, with consequent loss of reservoir energy, but at the present time continued activity is maintained to develop adequate reserves, so that production in these fields can be taken at a rate to correspond with good operating practice. Naturally, this good operating practice will be influenced to some degree by gas outlets and, in certain instances perhaps, by oil outlets. In any event, these last two controlling features will result in favorable rather than detrimental operation. In fields producing from great depths, ultimate production will be practically limited to the flowing and compressor life of the well, since there is as yet no economical method for pumping wells below depths of approximately 7000 ft. Experience has shown, however, that such pumping difficulties will be overcome and that production secured by pumping will add some to reserves established on the flowing life of the wells. California continued to operate under voluntary curtailment, but with unlimited transfers of allowable between various fields. Even though there was at all times considerable production above the Umpire's established quota, a constantly increasing demand reduced storage during the year. This increasing demand was due mainly to the rapid rise in Pacific foreign shipments from May to September. It is questionable, however, whether this favorable condition will be maintained over a prolonged period. (See Fig. 1.) Field Discoveries The great drilling activity during the year resulted in the discovery of three new fields in the San Joaquin Valley, as well as many extensions

Jan 1, 1938

By Kenneth Cottingham

The number of wells completed in Ohio during I940 was about 20 per cent more than during the preceding year, the comparative totals being 1020 and 1228. Of the 1940 completions, 327 were oil wells, 491 gas wells, and 410 dry. The completions for the past five years, divided into oil wells, gas wells, and dry holes, are shown in Table 2. Wells drilled deeper and input wells in water-flood areas are not included in the tabulation. The annual production of oil has decreased steadily in Ohio from the maximum of 23,941,000 bbl. produced in 1896. Table 3 shows the quantities of oil produced in the last five years. In 1940, the total was 3,052,000 bbl., produced by about 25,500 wells. The number of wells and the approximate quantities by grades are shown in Table I. Table i ,—Tabulation by Grade Grade 1 2 Barrels __________________________________________________________________________________________ Pennsylvania ............. . 1,198,000 Lima.................... . 325,000 Corning................... 3,730 1,159,000 Lodi...................... T,040 350,000 Cleveland................. 30 1:1,000 Total................... 25,500 3,052,000 The prices paid for Ohio crude oil in 1940, together with dates of changes in posting, are shown in Table 4. The production of natural gas in 0hio has declined from a maximum of 79,510,032 M cu. ft. in I9I5 S to 36,469,000 M cu. ft. in 1939, the most recent year for which a figure is available. Consumption reached its peak in Ohio in the year 1916, when it was 169,480,01r M cu. ft., declining to 114,720,ooo M CU. ft. in 1939. The produc-tion and consumption of natural gas in Ohio for the past five years are shown in Table 5. TAble 2.—Completions in Ohio during Past Five Years Numbs of Wells Drilled during Year YearI, ] Oil Gas Dry Total 1936............. 263 570 324 1,157 1937............. 317 503 45I 1,271 1938............. 189 433 288 gro 1939............. I70 501 349 1,020 19391940............. 327 491 410 1,228 Total.......... 1,266 2,498 1,822 5,586 Table 6 shows the number of oil wells and the number of gas wells completed by sands during 1940, with the average initial production per well for each sand. Table 7 shows the total number of wells drilled—oil, gas and dry—by sands. Development during 1940 Szth-Trenton.—For several years, considerahle interest has been shown in a horizon lying some 500 to 700 ft. below the top of the Trenton, known to the driller in western Ohio as the "green sand," and in eastern Ohio as the St. Peter. In 1939, ten 'lgreen sand" tests were drilled, all in western Ohio and all dry- In 19401 eight wells were drilled to this horizon, one of which was a small oil well (one barrel) in Men county- Of the remaining seven—all of which were dry-—one in Franklin County, in central Ohio, was drilled to a depth of 2903 ft. .Another was in Medina

Jan 1, 1941

By Kenneth Cottingham

The number of wells completed in Ohio during I940 was about 20 per cent more than during the preceding year, the comparative totals being 1020 and 1228. Of the 1940 completions, 327 were oil wells, 491 gas wells, and 410 dry. The completions for the past five years, divided into oil wells, gas wells, and dry holes, are shown in Table 2. Wells drilled deeper and input wells in water-flood areas are not included in the tabulation. The annual production of oil has decreased steadily in Ohio from the maximum of 23,941,000 bbl. produced in 1896. Table 3 shows the quantities of oil produced in the last five years. In 1940, the total was 3,052,000 bbl., produced by about 25,500 wells. The number of wells and the approximate quantities by grades are shown in Table I. Table i ,—Tabulation by Grade Grade 1 2 Barrels __________________________________________________________________________________________ Pennsylvania ............. . 1,198,000 Lima.................... . 325,000 Corning................... 3,730 1,159,000 Lodi...................... T,040 350,000 Cleveland................. 30 1:1,000 Total................... 25,500 3,052,000 The prices paid for Ohio crude oil in 1940, together with dates of changes in posting, are shown in Table 4. The production of natural gas in 0hio has declined from a maximum of 79,510,032 M cu. ft. in I9I5 S to 36,469,000 M cu. ft. in 1939, the most recent year for which a figure is available. Consumption reached its peak in Ohio in the year 1916, when it was 169,480,01r M cu. ft., declining to 114,720,ooo M CU. ft. in 1939. The produc-tion and consumption of natural gas in Ohio for the past five years are shown in Table 5. TAble 2.—Completions in Ohio during Past Five Years Numbs of Wells Drilled during Year YearI, ] Oil Gas Dry Total 1936............. 263 570 324 1,157 1937............. 317 503 45I 1,271 1938............. 189 433 288 gro 1939............. I70 501 349 1,020 19391940............. 327 491 410 1,228 Total.......... 1,266 2,498 1,822 5,586 Table 6 shows the number of oil wells and the number of gas wells completed by sands during 1940, with the average initial production per well for each sand. Table 7 shows the total number of wells drilled—oil, gas and dry—by sands. Development during 1940 Szth-Trenton.—For several years, considerahle interest has been shown in a horizon lying some 500 to 700 ft. below the top of the Trenton, known to the driller in western Ohio as the "green sand," and in eastern Ohio as the St. Peter. In 1939, ten 'lgreen sand" tests were drilled, all in western Ohio and all dry- In 19401 eight wells were drilled to this horizon, one of which was a small oil well (one barrel) in Men county- Of the remaining seven—all of which were dry-—one in Franklin County, in central Ohio, was drilled to a depth of 2903 ft. .Another was in Medina

Jan 1, 1941

By W. A. Ver Wiebe

The year 1940 was singularly unmarked by sensational developments in Kansas. Routine operations were carried on in a systematic, orderly fashion and the efforts of oil producers were concentrated on extending known fields. In Kansas an arbitrary yardstick for wildcats has been set up. A well drilled mile or more from a known pool or well is now considered a wildcat. A "rank wildcat" is one that is drilled at least 2 miles from any known producer. During 1940, rank wildcats resulted in the completion of 116 test wells, among which 16 were successful in finding new oil pools and the remaining I00 were dry holes. The ratio of successful wells to dry holes, therefore, was approximately I:6. During the year, 1890 wells were completed in eastern and western Kansas. This figure is somewhat lower than that given in several trade journals, because it does not include wells that were deepened or wells that were recompleted in a different geological horizon. About three fourths of these (1423) were completed as commercial oil wells (I220 in western and 203 in eastern Kansas). The commercial gas wells completed number 58 of which 10 are in eastern Kansas and 48 in western Kansas. Of the remzining completions 147 are dry holes in eastern and 262 are dry holes in western Kansas. Based on daily potential capacity, the new discoveries of the year account for a cumulative initial production of 46,000 bbl. in eastern and 2,128,000 bbl. in western Kansas. The state of Kansas attained a new peak in production, with the total of 66,245,000 bbl. for the year 1940, the number of contributing wells being 20,779. Thus the increase over 1939, when about 58 million barrels was produced, is considerable. The previous peak occurred in 1937, when 70,761,000 bbl. was marketed. In another still earlier peak, in 1917, slightly more than 45,000,000 bbl. was produced and sold. The production of gas probably reached a new peak also during 1940, with its total of 85 1/2 billion cubic feet. Between the peak of the year 1908, when over 80 billion cubic feet was produced, and that of 1940, the production dropped to a low point of 16 billion cubic feet in the year 1921. The number of test wells drilled was larger than in 1939; that is, 1890 compared with 1458. The first peak was reached in 1904, when 2782 wells were drilled. The number dropped off rapidly, to 368 three years later, but rose to the second and highest peak in 1918, when 4671 test wells were completed. In the period between 1904 and 1912 more gas wells were completed than oil wells. Between the high peak of completions in 1918 and somewhat lower peak of 1937, the low point was reached during 1931, with the completion of only 470 test wells. In the number of new pools discovered, Kansas again ranks high among the states. The exact number depends somewhat upon the interpretation of a "new" area— whether it should be called a new pool or a long extension of an old pool. Unfortunately, the matter of securing the right kind of production allowable also enters into this question. Often the decision regarding a new pool cannot be made until other wells

Jan 1, 1941