Search Documents

By David A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. 80122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available. Personnel involved in the investigation include J.R. Wait (Principal Investigator), D.A. Hill (Co-Principal Investigator), K.P. Spies, A.Q. Howard, and Lana Slusher (Administrative Assistant).

Jan 1, 1974

Late in 1974 at a meeting with the Cedar Coal Company in Chelyan, West Virginia, a very definite requirement for an automatic heat sensing fire suppression system for the type coal augers used in their mine was revealed. Several fires had been experienced, and while equipment loss was a consideration, operator safety was also a concern. As of that date no one had developed an automatic system specifically for fire suppression on coal augers. II. EQUIPMENT DEVELOPMENT As a result of the above meeting, an unsolicited proposal was made to the Bureau on March 1, 1975, and a contract was issued to provide the following services: A. Determine and define fire hazard problem on Compton Coal Auger. B. Modify or otherwise mike a Lease "AFEX" system suitable for protecting the fire hazard area developed in paragraph "A". C. Make installation of "AFEX" system. D. Monitor installation for reliability for a period of 90 days after installation. C. ConJurt a simulated fire test to determine effectiveness on system.

Jan 1, 1975

By R. E. Gray

[The purpose of the study is to investigate cases of subsidence over abandoned mined-out areas of the Pittsburgh Coal identified from published and unpublished sources and to determine through a consideration of the geology, topography, climate, mining activity, and evidence at ground surface, what mechanisms control subsidence .and under what circumstances it takes place. The study wan performed it two phases, the first to identify all documented incidents of subsidence in mined-out areas of the Pittsburgh coal Region; and the second, to study a particular portion of the region in detail, collecting pertinent data relative to the sites within, characterizing roil the nature of the subsidence and its economic consequences, and determining the applicability of the findings to other areas whore similar problems with the collapse of abandoned miner have been encountered.]

Jan 1, 1977

By Kay E. Goldberg

The Bureau of Mines conducted a study to develop and evaluate a training workshop for mine safety training personnel. The workshop was based on the Instructional Development Institute (IDI) which has been used for nearly ten years to train educators and administrators in the application of a nine-step model for defining, developing, and evaluating instruction. The Mining Instructional Development Institute (MIDI) was developed by investigators at the University of Southern California as a two-phase project. Phase I involved the modification of the six-day IDI program (including audiovisual presentations, workbooks, games, and exercises) for use by mine safety trainers as a workshop lasting three and one-half days. Phase II involved the evaluation and validation of the prototype MIDI workshop by means of a two-stage jury of experts and a prototype field trial. On the basis of data collected in the validation process it was determined that the institute provided an effective and useful method of instruction in mine safety training and that the institute would be especially valuable for mine safety training administrators and supervisors.

Jan 1, 1980

By David Allen Jones

A depleted county gravel pit was rehabilitated by contracting an artist to convert it into sculpture, rather than using traditional reclamation methods. The sculptor's ideas were generally implemented as designed, but problems arose because of a faulty survey and severe weather. Public reaction was critical. A design symposium was presented by retaining six artists to prepare designs for varied sites. A public forum was offered and video-documented for broadcast. A new art-reclamation project grew out of this project.

Jan 1, 1981

By Elaine T. Bowers

The Sunnyside single-entry project pioneered the use of single entries for longwall development in this country. During the 10-year course of the project, an immense amount of information was gathered. Over three miles of entries were observed primarily through instrument groupings placed in strategically located areas or "rooms." Nearly 1,200 instruments were monitored to gain information on the behavior of coal entries during development stages and through the mining of two longwall panels. This was one of the most extensively documented projects undertaken by the Bureau, The data gathered has a great potential for scientific research especially in the area of longwall mining. This Bureau of Mines report presents the ground control data gathered, in the form of computerized plots. Roof-to-floor deformation and load on cribs and roof bolts make up the bulk of the data, which is presented as load or deformation versus time. The plots are organized, generally, by the three main entries involved and, specifically, by the individual areas or rooms in those entries. No major attempt will be made, in this paper, to analyze the data other than to identify its source arid its history.

Jan 1, 1983

By Larry L. Wischhoefer

The Automated Breathing Metabolic Simulator (ABMS) is a versatile machine capable of performing almost any physiologically appropriate respiratory simulation. The first ABMS was delivered to the Bureau of Mines by IBM in 1973. Since then efforts have been made to refine the systems and components which make up the ABMS including the Breathing Simulator Module (BSM), Gas Analysis Module (GAM), and Supervisory Controller (SC)-each of which are also capable of stand-alone operation. Since September 1980, Reimers Consultants has been testing and modifying the ABMS and its components in order to improve the equipment and to develop simulation criteria and parameters. Changes have been made to the Phase I Design Plan and Performance Specifications; future improvements based on current experience are recommended; and test results of full scale testing conducted by Reimers Consultants in November 1983 on several types of breathing apparatus are reported and illustrated.

Jan 1, 1984

By Meliton M. Garcia

The volume of gases produced in major and trace amounts following the detonation of two water gel and two emulsion explosives in a mine were determined. The volume .of the major gases (CO, CO2, NO, and NO2) was measured immediately following detonation, during the mucking operation, and following the removal of the muck. Tests to identify and quantify the gases produced in trace amounts were performed following the detonation only. The volume of each major gas per pound of explosive (ft /lb) ;ranged as follows: CO, 0.0424-0.3231; CO , 0.6819-1.5632; NO, 0.0129-0.1320; and NO2, 0.0019-0.1111.. An approximate average of 95% of the gases produced was found in the test chamber immediately following the detonation, while less that 2% was found in the chamber following removal of the muck. Benzene was the most significant compound found to occur in trace amounts. Scaling tests performed with a water gel and an emulsion explosive suggest that the volume of the gases per unit mass of explosive detonated diminishes as the amount of explosive per blast increases.

Jan 1, 1986

This study of underground mine water inflow was initiated by the U. S. Bureau of Mines in March 1980. The objective of this study is to evaluate the hydrologic variables associated with surface water and ground water systems that affect the inflow of ground water into an underground mine. Data collection techniques are reviewed for their applicability for quantifying these hydrologic variables. Innovative techniques are also investigated. Existing analytical and numerical procedures for predicting underground mine water inflow are reviewed and evaluated. Over 300 computer models were reviewed for their applicability to modeling underground mine water inflow. The model UNSAT2 is utilized for modeling inflow to a shaft and tunnel or drift. This model and the techniques developed in this study are applied to two existing mines.

Jan 1, 1982

Tailings embankments can develop a high phreatic surface if the original design for the embankment does not include drainage facilities or if existing drainage facilities become ineffective. Subsequent raises can develop a seepage surface due to a high phreatic surface that can lead to stability problems. The U. S. Bureau of Mines amended contract J0100013 to initiate this study of horizontal drains in tailings embankments. This study developed a technique for determining the length of and spacing between parallel drains through the use of the finite element model UNSAT2. The analysis is based on the combined output of a vertical planar mesh and a horizontal planar mesh. The slot opening in the drain pipe and the length of the perforated section are determined from an analogy to water well design. The pipe diameter and gradient can be determined from Manning's equation. To the authors' knowledge, this is the first attempt at horizontal drain design using a finite element model. Additional research is recommended in this area.

Jan 1, 1982

By John W. Mentz

Phase I study efforts addressed: 1) acid mine drainage formation theory; 2) effects of inundation in reducing acid mine drainage formation; 3) summary information on the types of acid abatement technology currently available and the problems inherent in each; 4) analysis of two potential means of partially inundating abandoned segments of active underground mines to reduce acid formation. This subsequent Phase II Draft Final Report addresses all of the above, but concentrates on and defines Item 4. Seal construction techniques were taken through five logical steps as follows: A) Location Analysis; B) Coal Barrier Pillar Analysis: C) Ground Water Analysis; D) Design Considerations: E) Economic Analysis. The design details of both low wall dams and section seals were discussed in a series of segments: a) Case Histories; b) Feasibility Analysis; and c) Design (including representative calculations). Study efforts showed that both concepts are feasible only in certain mines where the geologic-hydrologic physical makeup is suitable to contain a mine pool. Low wall dams in particular were found to have extremely limited applicability as a means of pollution reduction. Section seals, while clearly dependent upon site specific conditions, have a some what broader range of utility and are more effective in pollution reduction. The proven dramatic reduction in acid mine drainage attributable to inundation makes this a concept that must be considered.

Jan 1, 1981

By James D. Eklund

Towards the goal of improving safety, economy and efficiency of scaling in underground metal/nonmetal mines, Battelle developed a combination prying/hammering scaling tool. A prototype was subjected to limited testing 1) to verify its operational functions and 2) to assess its potential capability in future underground testing.

Jan 1, 1983

This report describes Phase I of the project --Development of a Mechanized Scaler --performed by Battelle, Pacific Northwest Laboratories for the U.S. Bureau of Mines. The objectives of Phase I were to 1) assess the needs of the industry as related to mechanized scaling; 2) conceive, evaluate and select mechanized scaler concepts; and 3) prepare preliminary designs of the selected machine concepts. To assess the scaling needs of the industry, we reviewed both U.S. and foreign literature, evaluated U.S. scaling accident statistics, reviewed existing mechanized scaling equipment, performed a series of mine visits and telephone interviews with mine operators, and assessed the applicability of a loose-rock detection system. The literature review identified over 25 scaler-related articles. However, little of the information could be used directly in the conceptualization and design portions of the project. Three articles did supply information on a number of machines used in Europe, along with statistics describing their effect on mine safety. For example, the French reported a 50% reduction in the total number of scaling-related accidents and a full 80% reduction in the number of lost-time injuries in the Lorraine mining district.

Jan 1, 1981

By Charles Fried

The Coal Mine Health and Safety Act passed by Congress in 1969, called for research to alleviate the occupational stresses and hazards of coal miners. Spurred by a series of recent mine disasters the Congress directed the Bureau of Mines to increase its attention to the welfare of miners and to develop better working conditions and personal equipment for use in the mines. As one of the early steps in carrying out the provisions of the Act, the Bureau of Mines commissioned the Behavioral Sciences Group at the National Bureau of Standards to conduct a survey of the state of the art in ergonomics (human factors) as it has been applied to mining.

Jan 1, 1972

A computer program for the static load analysis of linear elastic structures is presented. It is the product of a two-year project for the development of a efficient program for the analysis of mine-type structures. The report is divided into two parts. The first part explains the general method of analysis, the computer program organization and the most significant numerical techniques used. The second part is a user manual for the computer program. The FORTRAN IV computer program deck and example problems were transmitted separately to the sponsor. Request for a copy of the program should be directed to the Bureau of Mines, Denver Mining Research Center.

Jan 1, 1972

By R. L. Cosgriff

A commercial, battery-powered mine vehicle has been equipped for remote operation in coal mines. This vehicle is controlled by an operator from the remote station. Command signals originating at the remote station as well as video and data signals originating on board the vehicle are relayed between the remote station and vehicle using a single coaxial line. This coaxial line is normally 2,000 feet in length and is reeled in and out from a drum mounted aboard the vehicle The vehicle has a maximum speed of 6 ft/sec and a minimum speed of 4 ft/sec using 36-volt excitation of the traction motor. If this traction motor is excited by two of the three batteries, 24-volt excitation, the vehicle will travel at approximately 2 ft/sec. The speed can be reduced by the operator to 1 ft/sec. This vehicular system has been tested in coal mines. Presently, the major limitation of this system is associated with fatigue failure of the splices in the coaxial line and lack of mobility caused by its 3-wheel design.

Jan 1, 1974

By Wesley G. Holtz

A project to demonstrate the feasibility of retorting oil shale by the Paraho vertical retort process was carried out at Anvil Points, Colorado during 1974 to 1976. As a part of the demonstration project, laboratory and field tests were performed to determine the physical and chemical properties of the retorted shale for use in the development of eventual full-scale disposal plans. The material which exits from the Paraho retort is classified as a non-plastic silty gravel by the Unified Soil Classification System. The particles have an apparent specific gravity averaging near 2.60 and a mass specific gravity averaging near 2.00. The material can be compacted by normal laboratory and field construction methods to about 90 to 100 pounds per cubic foot dry density depending upon the degree of compactive effort applied. The addition of moisture does not improve compactibility appreciably. When high compactive effort is applied the retorted shale is classed as impervious to water flow. The compacted retorted shale exhibits shear strengths in the same order as those observed for silty gravel soils. If the compacted material is cured (long tune simulation testing) prior to strength testing considerable strength gain can be obtained from cementing action. The amount of cementing developed is dependent upon heat treatment and other operating modes of the retort.

Jan 1, 1976

By J. L. Buckley

A survey of previous underground mine fires revealed a number of reported fires may have been caused by malfunctioning stationary electrical equipment. Therefore, an evaluation of conventional fire protection systems was conducted to determine their usefulness in the protection of this equipment. To simplify the problem and facilitate the handling of data, the under-ground mine was divided into nine work areas. Representative combustibles and associated hazards characteristic of each area were identified. Conventionally available fire protection systems were then examined and evaluated to determine engineering and cost feasibility, effectiveness and reliability for the development of fire protection guidelines which could be used within the nine areas of interest.

Jan 1, 1976

By Robert L. Lagace

This report presents a mathematical model for the propagation of UHF radio waves in the large cross-section tunnels of a room and pillar limestone mine, and describes the analysis of a small amount of propagation data obtained in a limestone mine. The model and analysis is based on the waveguide mode theory developed earlier for the transmission of UHF waves in coal mine tunnels, with allowance for propagation losses due to refraction into the tunnel walls, to scattering by wall roughness, and to long range random tilt of the walls. Propagation around corners and through pillars is also examined based on a ray theory approach, together with the beneficial effects of placing reflectors at intersections to significantly reduce corner losses. The theory is found to be in fair agreement with the data; however, additional in-mine measurements are needed to provide a more conclusive test of the model.

Jan 1, 1979

By Mark Davis

As a follow-on to previous investigations, reduced treatment levels for the optimum fire retardant/preservative system were evaluated. An impregnation of 3.5 lbs/ft3 of Fyreprufe followed by 3.5 mils of Albi 107A plus an Albi 144 top coat provides adequate flammability and flame spread protection. However, there is a significant loss in compressive strength at this retention level, particularly parallel to the grain. A pilot-size pressure impregnation cell was installed for use in treating larger quantities of wood. Based on the optimum fire retardant/preservative treatment system - Fyreprufe/ACC impregnation followed by Albi 107A/144 intumescent paint - a model treatment pro¬cess was developed, capable of handling 3 million board feet per year. Associated annualized costs per thousand board feet (K bd. ft.) for treating 12" x 12" timber were calculated to be: Impregnation: $-63.00/K bd. ft. Coating: $112.00/K bd. ft. A literature search was conducted to identify materials and techniques suitable for a localized stench warning system for heated mine timbers. Based on this review, a number of stench warning concepts were developed. Those based on surface coating were given a preliminary laboratory evaluation.

Jan 1, 1982