Search Documents

This paper briefly describes the shaft, including sinking, steel sets and their installation, shaft equipment and winders.INTRODUCTIONThe New Broken Hill Consolidated Ltd. Service Shaft is a vertical concrete-lined circular shaft, 20 ft. in diameter with -steel sets spaced at 12-ft. centres. The diameter of 20 ft. was established as the minimum that would enable the shaft both to house the proposed hoisting and service equipment and to satisfy ventilation requirements as a downcast airway. The 12-ft. set spacing was based on South African practice in similar types of shafts.The shaft extends from the surface to 28 ft. below No. 22 Level, a total depth of 3,194 ft. Sinking was commenced in September 1946, and equipping completed in January 1955. Initially the shaft was sunk and concrete-lined to a depth of 52 ft., using a stiff-legged crane and clam-shell grab for mucking. Operations were suspended at this depth to allow the installation of the steel sinking head-frame, winders and ancillary equipment.Sinking and concreting were recommenced after four months and continued to a depth of 1,035 ft. 6 in., where the shaft connected with a pilot opening. The concrete lining was poured as sinking progressed and was piped from the surface to this depth, after which all concrete was lowered in buckets and discharged through a distributor suspended in the shaft. A cycle of stripping to the pilot opening and concreting was continued until the shaft reached No. 22 Level. From this level the remaining 28 ft. was sunk full size. All plats were cut and concreted as sinking progressed.

Jan 1, 1957

By Anton Gronningsater

AS we know, Sir Henry Bessemer introduced Bessemer converting in the steel industry about 1855. It was not until twenty years later that the principles were adopted by non-ferrous metallurgists. In 1880, Manés first produced blister copper from matte in a converter, a very important forward step in copper metallurgy. For thirty years, up to about 1910, bessemerizing of copper matte was carried out in the acid-lined converter. It is not necessary here to enumerate all the shortcomings of that operation, one of which was that it strictly limited the grade of matte that could be treated; a 35 per cent matte was low in those days. From the early days of copper converting, many and repeated attempts were made to use a basic converter lining, and the older metallurgists will remember the numerous reports and discussions in connection with such experiments. These make interesting reading. I quote from a book published in 1900: ?'The siliceous lining is as much a part of the process of copper converting as magnesia lining is in the basic bessemer treatment of phosphoric iron, and it is suicidal to attempt any other kind of lining, either water-jacketed or basic.' "Even if the silica could be introduced in this way (through the tuyeres), it would still produce another trouble in the converter. The small particles of silica, being cold, would combine very imperfectly with the iron oxide and produce granulated and pasty slags, which could not be skimmed or poured out of the vessel".

Jan 1, 1942

THE Phillips River gold and 'copper field is situated on the south coast of Western Australia, about 200 miles east of Albany, 180 miles west of Esperance, and: 250 miles south of Southern Cross, forming the southern extremity of what Mr. H. P. Woodward classes as the fourth belt of Pre-Cambrian rocks, and the first auriferous belt, whicf extends northward through Southern Cross, Mount Magnet, and Cue. The field may be considered the premier copper producer of the State. The first mineral discoveries were made about 1892; when gold, copper, and iron pyrites were found; but, owing to the isolation of the district and the scarcity of water, both in the locality and on the route thereto, little work was done for some years. In1899, however, payable gold reefs were opened up, and the district began to attract attention.The southern portion of the district is composed of limestone and sandstone rocks, forming the coastal series, and is for the most part flat, broken only by a few low hills and ridges, except to the west, where Cape Barren and Eyre's Range stand out...

Jan 1, 1917

By Pound J. R

THIS mine, which is the property of the S. and M. Syndicate, London, is located at Moina, in North-West Tasmania, 18 miles from Stavertorr railway station and 36 miles from Devonport. There are metalled roads from both of these places, and, althoughhilly, these are good for team or motor traffic. Mails and passengers are provided for by a tri-weekly coach service from Sheffield, a railway town, distant 23 miles. The Moina mining field is situated on a main spur between the Forth and Iris Rivers, andat an elevation ranging from about 500 ft. above sea-level at the Forth River to 2400 ft. at the All Nations mine. The elevation at the mine office of the S. and M. mine is 1900 ft. The average annual rainfall, as recorded for the past eight years, is. 68 in.This inclildes, however, a couple of years during which the rainfall was much above normal, and taken over a longer period 60 in. would be nearer the average.

Jan 1, 1919

The Takasima Coal Mines comprise four islands near the entrance to Nagasaki Harbour, and are owned and worked by the Mitsu Bishi Company.There are several unusual features in the occurrence and working of these coal seams, the steep angle of "dip," the numerous seams of good coal separated by hundreds of feet of sedimentary rocks, the extensive faulting of the strata, and the way in which the coal is won, when so little surface is available for works, and where there is the ever present danger of subsidence of the roof and consequent flooding of the workings by the ocean. The author trusts that short notes on these few points will be of interest to members.The Islands are named respectively Hasima (Extreme Island), Nakanosima (Middle Island), Takasima (High Island), and Yokosima, and are situated about one mile from the main land.

Jan 1, 1901

IT is intended in this paper to present in broad outline to the members of the Institute a short account of the conditions and operations that constitute what is, variously known as Subterranean Warfare, Military Mining, or Tunnelling. Realizing ,the magnitude of the operations, and the varied and minute details met with in them on,the Western Front, it is the writer's intention to confine these notes to operations carried out by the First Australian Tunnelling Company. In so doing there is no wish to detract from the very fine records of the Second and Third companies it is to be hoped that members of the Institute (or others) who were with these companies will write accounts of their doings-the former in the water-logged areas to the south of Armentieres, and later in the sand-dunes at Lombardzee, and the latter in the chalk area of the Lens coal...

Jan 1, 1920

In redesigning the cyanide plant at Mount Torrens, in conjunction with Mr. L. W. Grayson, the manager, several minor alterations were introduced in order to have the operations under thorough control, and these having proved serviceable may be of sufficient interest to merit a description here. The lixiviation vats, though only 8 feet in diameter, were retained, but the pipes leading away from the bottom were reduced from two inches to half-an-inch in diameter, and had a fall to the zinc boxes of about 4 feet. As these small pipes were completely filled by the solutions fiowing away from the vats, they exerted a suction equal to their fall and thus hastened the rate of flow, so that tailings containing a larger proportion of slimes could be treated than was possible where the larger pipes were used, as, there not being sufficient fiow of solution to keep the latter filled, no suction could be obtained with them. It was found that with'most of the tailings treated a sufficient flow could be obtained from the half-inch pipes when the taps on, them were only one-third to half open. The lower end of each of these pipes was connected by means on indiarubber tubing with the sille hole of 11 in aspirator bottle, and to the mouth of this bottle a few feet of similar tubing was connected, so that the solutions coming through could be directed into either of the fixed tubes leading respectively to the waste water tank the strong solution zinc boxes or the weak solution zinc boxes.In working the vats, the following method was found to give good results. While filling the vats with tailings the taps were left open, so that the water might drain off into the waste water tank the surface of the tailings was carefully levelled. When the strong solution was run in at the top, the air contained in the interstices of the tailings was forced through the half-inch pipe at the bottom as a strong blast, instead of, as I believe js usual, escaping by means of channels formed by it through the tailings, and thus tending, it would appeal, to render the disposition of the tailings less even and to make.

IN this paper an attempt is made to describe the sluicing operations on the tin fields of north-eastern Tasmania. No claim is made to completeness, for much of the ground has already been covered, and nothing is to be gained by needless repetition. On this account some portions of the subject have obviously received but attention in order that others may be rather more fully dealt with; for instance, referring to the accuracy of various methods of valuing alluvial deposits, particulars of efficiencies, and water duties on both overburden and drift; also, the system of recording water distribution, &c. The plans of the tin-streaming shed, sluice and feed race, and overburden tail-race represent types of the most modern design.GEOLOGY. The principal alluvial dcposits being worked at the present time are situated either in the ancient or modern bed of the Ringarooma River or its tributaries. This river flowed in a north-easterly direction, receiving numerous tributaries on either bank...

Jan 1, 1910

By Bradley Stoughton

(Cleveland Meeting, October, 1912.) [SECRETARY'S NOTE.-To avoid repetition of foot-notes, references to authorities are made in this paper by means of figures, referring to a numbered list in the appendix.-J. S.] INTRODUCTION. THIS paper gives the results : first, of a research into the somewhat extensive literature of titanium; and second, of a series of original tests upon the effect of titanium on iron castings. New investigations have also been made upon the effect of titanium on steel, but I hope to treat this subject in an independent paper at some later date, and, therefore, will not discuss the experiments in detail here. The combined results of this study, which extended over a period of more than two years, can be briefly summarized as follows: 1. Steel or cast-iron, in which the titanium is properly proportioned, and which has been properly treated, is improved in strength, toughness, and durability against wear, such as, for example, the wear of railroad-rails, of steel and chilled-iron .rolls, car-wheels, etc. 2. These improvements seem to be caused, not so much by the direct effect of titanium on the metal, as by its cleansing influence in removing harmful impurities, such as oxygen and oxides, nitrogen, occluded slags, and perhaps also sulphur. It appears also to reduce segregation, which would contribute to the same end. 3. In order that its effects may be fully realized, the treatment of steel or iron with titanium must be correctly performed. There are a few simple, but essential, details to be observed; if they are neglected, the best results cannot be expected. To illustrate by an example : A series of tests on cast iron

Nov 1, 1912

Soon after the Rosebery concentrator commenced operations in 1936, an investigation was begun in an attempt to discover a substitute for cyanide in lead flotation. Cyanide is an excellent depressant for zinc and iron, but it also powerfully depresses the copper, silver and gold bearing minerals present in Rosebery ore, thus allowing them to pass through to the zinc concentrate or final residue where they are of little or no value.The investigation was not entirely successful, but it did indicate that sodium bisulphite or sodium sulphite could be used as a depressant for zinc without depressing the copper, silver and gold bearing minerals. The sulphites were, however, much inferior to cyanide as apyrite depressant.At about this time, I. W. Wark, using the captive bubble technique, had shown that, at the concentrations normally used, sodium aerofloat is not a promoter for pyrite or galena in alkaline solutions (see his book "Principles of Flotation", p. 188). Some preliminary tests on the production of a copper concentrate from Rosebery ore were therefore carried out using sodium sulphite as depressant and sodium aerofloat as promoter.The results of this work were promising but, since Rosebery ore usually carries only about 0·5% copper, there did not seem to be much incentive to carry the work further. With the outbreak of war, however, Australia became desperately short of copper and the relatively small amount in the ore. became of sufficient importance to...

Jan 1, 1952

ADVANCES IN EXTRACTION METALLURGY AND REFINING A symposium organised by the Institution of Mining and Metallurgy will be held in London from 4th to 6th October, 1971. Particulars can be obtained from: The Secretary, Institution of Mining and Metallurgy, 44 Portland Place, London WIN 4BR, ENGLAND. ICAMC -71 - HUNGARY The Third International Conference on Automatic Control of Mines and Collieries will be held at Balantsfured, Hungary from 27th to 30th September, 1971. Further particulars can be obtained from: ICAMC - 71, Budapest 3, P.O. Box 115, HUNGARY. AUSTRALIAN INSTITUTE OF MINING AND METALLURGY Illawarra Branch A symposium on "Blast Furnace Injection" is to be held at Wollongong University College from 15th to 17th February, 1972. About 20 papers on various aspects of blast furnace injection will be presented, including two on nonferrous furnaces. Further particulars may be obtained from: N. Standish, Chairman, Symposium Committee, Wollongong University, Australia 2600.

10th COMMONWEALTH MINING AND METALLURGICAL CONGRESS-CANADA, 1974 The Commonwealth Council of Mining and Metallurgical Institutions has received and accepted an invitation from The Canadian Institute of Mining and Metallurgy for the 10th Commonwealth Mining and Metallurgical Congress to be convened in Canada in April, 1974, immediately following the Annual General Meeting of The Canadian Institute of Mining and Metallurgy. It is proposed that the Congress centre will be Montreal and that, after technical sessions, tours of operations will be arranged. Further information will be issued in due course by The Canadian Institute of Mining and Metallurgy and enquiries should be addressed to the Executive Director of the Institute, 906-1117 Ste. Catherine Street West, Montreal 110, P. Quebec. NOTICE TO ALL STUDENT MEMBERS OF THE SOUTH AFRICAN INSTITUTE OF MINING AND METALLURGY The Institute offers each year for competition among Student Members of the Institute a prize, or prizes, should entries so warrant it, of up to the value of R100 to be awarded to the Student Member or Members who submit the best paper or dissertation on a topic appropriate to the interests of the Institute. In the case of Student Members who are in full time study at a university the dissertation or thesis which they may have to write in part fulfilment of their university curriculum may be accepted provided it is presented in a manner and on a topic suitable for publication in the Journal. The closing date for the receipt of papers shall be 31st December each year.

A form of wet pelletization is described where the bridging of the individual particles is achieved by a second liquid phase that pref- erentially wets the suspended solid particles. The phenomenon can be used to obtain efficient separation of solids from carrier liquids, to form spheres from finely divided solid materials, and to separate selected constituents from a body of mixed solids. Typical examples of each of these applications are presented.

Jan 1, 1974

This paper summarizes the results from a project aimed at adapting scroll centrifuges for application to the dewatering of flotation concentrates. The main impetus for the project was to reduce the high cost and footprint size of the technology currently used to dewater fine coal. The technical challenge was to enhance solids capture by incorporating a laser-cut screen into the design of the basket. The project has shown that a pilot-scale scroll centrifuge can be used to dewater froth concentrate. A number of different basket designs were tested, the best results being achieved with a basket comprising a laser-cut screen of aperture 70 µm. The best result on a sample of untreated flotation concentrate, which was taken from the open trough flotation cells at a coal preparation plant (CPP) in NSW was a solids recovery of 82 wt% at a product moisture of 24.3wt%. By comparison the best product achieved with a conventional wedge wire basket was a similar moisture content but solids recovery was only 64 wt%. This could only be achieved after the feed had been artificially thickened. Conditioning of the centrifuge feed with polymer flocculants led to an increase in recovery up to 88 wt% with a moisture content of ca 25 wt%. It is thought that optimizing additive selection and conditioning parameters, as well as screen aperture and open area, could improve performance still further. The results were obtained using centrifuging conditions (centrifugal force, feed solids, feed rate) in the pilot-scale machine which should be possible to translate into conventional designs of commercial scale machines, without downgrading solids throughputs. However only with full-scale trials will it be possible to establish this assertion with certainty.

Jan 1, 2001

By J. Hines

Traditionally, fuel oil or diesel was the collector of choice in coal flotation, but in recent years these materials have come under increased scrutiny because of concerns about the toxicity of some components. In response to these concerns, Georgia-Pacific Chemicals LLC has commercialized a patent pending coal collector (Talon® 9400 reagent) that is 100% derived from the pulping of trees. This study presents a comparison of yields and recoveries for different coal collectors, including the one derived from the pulping of trees.

Jan 1, 2011

By M. Kerr, Petra Lampinen, Jinming Zhang, Petra Brodin, C. Hull, Nils-Johan Bolin, R. Asmatulu

"According to Darcy’s equation, the rate of dewatering varies as inverse square of the surface area of the particles to be dewatered and is proportional to the pressure drop across a filter cake. Thus, the difficulty in dewatering fine mineral concentrates can be overcome by using high-pressure filters. When treating ultrafine particles, however, it is often necessary to further dewater the filter cake using a thermal dryer. In the present work, novel dewatering aids that can reduce the pressure requirement have been developed. The reagents are designed to reduce surface tension, increase particle hydrophobicity and increase capillary radius, all at the same time. They were tested for dewatering mineral and coal concentrates in both laboratory and pilot-scale tests. The results show that the use of the novel dewatering aids can substantially reduce cake moistures and, at the same time, increase throughput. In this communication, the case history of using the reagents commercially at the Garpenberg concentrator is given. The use of the novel dewatering aids allowed the operators to use a vacuum filter to obtain desired cake moistures and obviate the need to use a thermal dryer.INTRODUCTIONDewatering is an integral part of mineral and coal processing operations, as it is necessary to remove water from concentrates (or clean coal) to minimize shipping costs, meet contract specifications, and recycle the process water. In general, the cost of dewatering increases with decreasing particle size, which can be attributed to the difficulty in removing the water trapped in the pores (or capillaries) formed between the particles constituting a filter cake.The various parameters affecting the process of dewatering, including the effect of particle size, can be understood in view of Darcy’s equation (Darcy, 1856):"

Jan 1, 2005

By Dale Ramsey

Emulsion explosives have become the product of choice for many blasting applications and are not limited to just extreme wet hole conditions or special application environments as in the past. Today’s novel emulsion technology has evolved over many decades, allowing a great diversity of formulations, Emulsion explosives can be effectively designed to produce very high energies, cap sensitive high explosive cartridges to bulk blasting agents, with varying viscosities, stable VOD’s, excellent water resistance, long shelf life and sleep time. They are also conducive to the mixture of emulsion, An/F0 blends in varying proportions and are amenable to any type of sensitizer. The key to a stable, reliable and consistent emulsion formulation is the careful mixing of the internal phase, which consists of a solution of oxidizer salts suspended as microscopically fine droplets, with the surrounding continuous fuel phase. There are few blasting applications today where some form of an emulsion explosive cannot fit the application. In massive, hard rock, dense, tightly jointed and fine grained rock types, the emulsion explosives are the best choices in creating new fracture networks for good fragmentation with a few alternatives. In such environments, emulsions with expanded drill patterns often result in better economics than the use of straight AnLFo. This paper will cover emulsion formulations, sensitizing options, product testing, material handling, and blast optimization, Emulsion explosives characteristics have also proven to reduce adverse environmental effects such as noxious fumes, ground vibration, and airblast while still remaining cost effective.

Jan 1, 2000

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

By P. A. Dimas

A new family of sulfide flotation collectors has been developed in our laboratory. These formulations are comprised of novel renewable materials combined with conventional reagents. The resulting diversity permits tunability of collector chemistry to meet a range of flotation problems. Several attributes of the new collectors are presented.

Jan 1, 2012

By F. J. Tavera, J. A. Finch

A probe suitable for on-line measurements of gas hold-up in industrial flotation systems has been developed. It is based on an open cell for measurement of slurry-gas conductivity and a novel syphon cell for measurement of slurry-only conductivity. The desired behaviour of the two cells was demonstrated and estimates of gas hold-up were shown to be in good agreement with independent measurements. The gas hold-up probe was used as a diagnostic tool to assess the operation of flotation columns. Differences in gas hold-up between baffled sections in two industrial columns were detected

Jun 18, 1905