Search Documents

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively.INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively. INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By Mohammad Noaparast, Babak Fotoohi

"Due to certain advantages in (semi-)Autogenous-Ball mill circuits in most of the high-throughput ore grinding units of mineral processing plants, much attention is paid to optimize the mill performance. Despite the maturity of the grinding mill mechanical design, there had been made less attention to the efficiency of the grinding media in the past. In this research, the possibility of establishing a relationship between liner/lifter wear rate and variations in the composition of the iron ore (from Chadormalu mine) is investigated.Measurements and determination of liner/lifter wear rates and patterns concluded in recognition of critical liner segments exposed to much abrasion during the ore grinding. After metallurgical analysis of liner materials and correlation of wear rate with the ore composition, the homogeneity in the metallurgical microstructure of the alloyed steel (such as the uniform distribution and amounts of the constituent phases) was determined as the most influential factor in the response of the liner/lifter to the variations in the ore composition. Magnetite with greater abrasion index than hematite, in finer particles, is responsible for additional abrasion of liners; hematite with greater work index exists in the mill with larger particle sizes, thus it could produce wear on liner parts with less tolerance to impact as is the situation for martensitic steels.INTRODUCTIONThe mineralization in Chadormalu plutonic iron ore deposit is consisted of mostly magnetite, hematite, martite, apatite, quartz and carbonates. The average composition of the ore is presented in Table 1. In the processing circuit, the gyratory crushed ore reduced to 30 cm would finally be the feed to three similar 32’ semi-autogenous mills in parallel processing lines. The pulp in the mill would have the characteristics mentioned in Table 2. The quality of the mill output has its direct effect on the downstream processes either physically or chemically (e.g. in cycloning or flotation respectively). In order to take advantage of optimum performance for these circuits, a close control of the ore grinding conditions is necessary; because any shortages in throughput, liner/lifter damage or changes in ore composition could bring the unexpected casualties. In this work, it has been attempted to find (possibly) a reasonable relationship between variations in ore characteristics together with liner quality and the amount of wear rate in different liner/lifter segments of a semi-autigenous mill. Liner/lifter segments are supplied by three different domestic steel making companies. The alloy structure of the liners/lifters is made up of pearlitic chromoly steel."

Jan 1, 2005

By Nikhil Dhawan, Shrey Agrawal, Veeranjaneyulu Rayapudi

India’s steel vision of 2030 requires a huge amount of quality iron ore. The utilization of low-grade iron ores such as banded iron ores will play an important role to achieve the same production. The absence of alumina impurities in the banded hematite jasper (BHJ) ore provides it an edge over other low-grade iron ores. The conventional beneficiation techniques such as magnetic separation and washing were found to be ineffective to produce suitable feed (Fe ~ 60%) for the blast furnace. It was found that microwave exposure provides significant enrichment to the low-grade iron ore and can be used as a pretreatment step in the beneficiation of similar low-grade iron ores. The above study reveals that hematite phase is susceptible to microwave exposure which enhances the separation of iron values from impurities. Under optimum conditions, an iron-enriched concentrate with 61% Fe, 85% Fe recovery at 50% yield can be achieved from BHJ feed ~ 38% Fe. The pretreatment process for BHJ beneficiation includes only microwave exposure without any chemical additive and may prove economical and industrially feasible.

By Cem Şensöğüt, Özer Ören, Yaşar Kasap

The mining sector, which has an important place in terms of raw material and energy supply, is referred as a sector with one of the highest fatal accidents in comparison with other sectors. In this century, where occupational health and safety awareness has increased, it is important to review the past accident statistics and to determine the current deficiencies by using the information in the inventory. In this study, the Malmquist total factor productivity index (MPI) has been utilized to investigate the changes in the work accidents occurring in the Western Lignite Corporation (Turkey), where underground and surface production methods are applied, and to determine the measures to be taken. According to the results obtained, both the decrease in production amount and the increase in the number of accidents caused inefficiencies during the period in concern due to the expected 10-year economic life of the mechanized system operating in the underground production panel that came to an end in 2007 and the flooding took place in early 2017. Compared with the underground operations, it has been determined that production can be carried out at the appropriate scale despite the heavy working conditions encountered due to the changing climatic conditions and the progress of production in the surface operations.

By J. Gustavsson, S. Holmin, Å. Afvander, E. Rosseland, E. Zimmerman

There are numerous advantages in replacing lead-based anodes with mixed metal oxide (MMO) coated anodes in copper electrowinning; for example, lower energy consumption, improved working conditions for operators and less environmental impact. Since 2012, Permascand AB in Ljungaverk, Sweden has evaluated Permascand coated titanium anodes in copper electrowinning pilot trials at Glencore Nikkelverk in Kristiansand, Norway. The investigation has proceeded in three different steps (Phase I, II and III). In Phase I, different Permascand coatings, electrode structures and coating methods were investigated. The results showed that improved current distribution, lower energy consumption and longer service life could be obtained with expanded mesh electrode structure in a box configuration compared to rod anodes in a single-mode construction. In addition, improved current distribution and less coating wear was found when electrostatic spray coating was used instead of brush (manual) coating. It was also found that the extrapolated service life from controlled lab experiments at 200 A/m2 was much shorter compared to what was experimentally obtained in copper electrowinning pilot trials at similar current densities. This was mainly attributed to different coating failure mechanisms in lab and industrial copper production. INTRODUCTION Traditionally lead-based anodes have been used in copper in electrowinning due to lower cost. But there are many advantages in replacing lead-based anodes with mixed metal oxide (MMO) coated titanium anodes in copper electrowinning, such as lower energy consumption, higher corrosion resistance, improved working conditions for operators and less environmental impact. Still, many facilities are using lead-based anodes, although the progression of using metal oxide coated anodes in copper electrowinning has slightly increased (Robinson et al., 2012).

Jan 1, 2019

By I. Çinar

Cappadocia is not only a region of Turkey with historical and touristic importance. During the cutting and processing of volcanic tuff, quarries in this region release large amounts of tuff into the environment that is viewed as waste. The release of this waste constitutes an economic loss and contributes to environmental pollution. However, through experimentation with deformation, weight per unit of volume, water absorption, uniaxial compression strength, modulus of elasticity, and point load strength index, volcanic tuff and marble dust composite materials can be produced for use in the building sector. In this study it was observed that, as the percentage of volcanic tuff dust in the mixture increased, the water absorption rate of the material increased, and uniaxial compression strength and point load strength decreased. The produced composite samples used in this study were kept for a predetermined number of times per day, and no deformation in the surface characteristics of the materials was observed. In a statistical parameter analysis, averages, variances, standard deviations, coefficients of variation, and skewness coefficients were calculated. Covariance changes between experimental parameters were also determined. In this study, two types of volcanic tuff dust, that is, yellow and red, were produced during the production of tuff-marble dust composite material. When the percentage of either type of volcanic tuff dust was increased, an increase in water absorption was observed. It was also observed that when the percentage of volcanic tuff dust was increased, uniaxial compressive strength and point load strength decreased. Furthermore, the physical and mechanical properties of the materials obtained by mixing different colored tuff powders and marble powders in different proportions were evaluated using statistical parameter analysis.

Mar 5, 2025

By Gabriel S. Esterhuizen, Anthony T. Iannacchione

The roof rock in underground limestone mines in Northern Appalachia can be subject to high horizontal stresses in spite of the shallow depth of the workings. The high stresses can cause roof stability problems. The National Institute for Occupational Safety and Health staff have observed a distinctive asymmetrical mode of failure at the pillar-roof contact in two underground stone mines, which is different from the typical failure mode observed in response to excessive levels of horizontal stress. A dip of greater than 5° was identified as a possible cause of this mode of failure. Numerical model experiments showed that an increase in the dip of the workings can cause an increase in the stress at the up-dip corner of the roof beam. A case study is presented in which failure at the pillar-roof contact was observed where the dip of the workings was 7° in a high horizontal stress field. Numerical modeling showed that the relatively small dip of the workings could have induced stresses changes in the immediate roof that would explain the failures. The model results also showed that this mode of failure is less likely to occur if the limestone pillars contain weak bedding planes that provide stress relief. In addition, the results showed that for the conditions at the case study site, the stress in the roof beam was not sensitive to the thickness of the roof beam or to the excavation span. The high horizontal stresses at this site are an important contributing factor to the observed failures.

Pressure drops were measured in a column packed with glass spheres and wax particles, both in random and preferential distributions. Variables investigated included wax content, gas flow rates, and temperatures.It is shown that for random distribution of wax, pressure drop is exponentially related to wax content above the melting point of wax and that below this it increases with increasing gas rate and temperature.For preferred distribution of wax the highest increase in pressure drop is obtained with horizontal distribution of wax and the least with vertical distribution.Comparison with operating blast furnace data and application of results to practice are also included.

Jan 1, 1970

By Ali Hasham

Reduction rates of FeO in CaO-SiO2-Al2O3 slags by Fe-C melts have been investigated experimentally at 1723 K. The rates were estimated using experimentally determined CO(g) evolution rates. Flash X-ray images were employed to visualize the behavior of the melt-slag interface during the reactions. The influence of melt interface was examined by conducting two types of experiments - (i) dropping one (or several) Fe-C droplet(s) weighing 2 g into the molten slag bath, and (ii) dropping a small amount (10-30 g) of slag onto a Fe-C melt weighing 400 g. The rates from both types of experiments were compared and analyzed to determine the rate limiting steps. It was established that neither the carbon transport in the Fe-C melt, nor the transport of gas species in the gas film adjacent to Fe-C melt was responsible in limiting the reaction rate. It is possible that the slag phase mass transport may be controlling the initial reduction rate in the droplet experiments. However, a, different mechanism was responsible in limiting the reduction reaction when the overall %C in the droplets fell to about 2-3.

Jan 1, 1992

By Olga Karabelchtchikova

Keywords: Multipass grinding, Residual stress, Retained austenite, X-ray diffraction The study investigated residual stresses behaviors and their superposition effect in D2 dies for thread-rolling applications. A nested factorial experiment was applied to test hypotheses that the residual stresses profiles change due to combination of heat treatment and multipass grinding operations, and that certain patterns can be derived due to the memory relationship between pre-existing and final residual stresses distributions. The amount of the retained austenite along with residual stresses in variation with depth was measured using x-ray diffraction technique. Statistical analyses indicate that the proposed hypotheses hold. Residual stresses distributions as well as tensile peak location were found to be significantly influenced by the treatment parameters used. Unique characteristic patterns in the residual stresses profiles were observed due to multipass grinding technique across all experimental conditions. This finding suggested a plausible memory relationship between the cutting passes, and the causes of the foregoing results are further proposed and discussed.

Jan 1, 2005

By Wolfgang Schott

The propagation velocity of in-seam seismic (ISS ) waves depends on frequency which is also known as dispersion. This dispersion is not only determined by the thickness of the coal seam and its dirt hand content (i.e. thickness and position), but also by the rock type and its condition (soft or compact) above and below the coal. A coal panel completely surrounded by roadways was investigated using the in-seam seismic transmission survey technique. Along the roadways the immediate roof was either sandstone and shale- The seam thickness varied between 1.20 m (sandstone in the roof) and 1.40 m (shale in the roof) and a fault system (normal faults) crossed the panel with a total throw of about the seam thickness. Below this coal seam another coal scam with a thickness of about 80 cm exists. Its interval shown by exploratory drilling changes from about 60 cm to more than 6 m (scam splitting). Tomographic inversion was applied to the dispersion of the measured ISS waves and velocity distributions were calculated at frequencies found to he most sensitive to changes in the seam thickness and the distance to the coal seam below. By correlating the velocity distributions with known values along the roadways approximate distributions of the coal seam thickness and the seam splitting within the panel were produced. The mining of the coal panel had already been finished and comparison was made between the survey results and the actual situation as far as it was documented. Prediction by the seismic survey was partly in good agreement with the actual held conditions or showed at least the same trends.

Jan 1, 2003

By S. Kevin McNeil, William Joa, Catherine Johnson, S. Omar Garcia

The geometry of an explosive is known to have a fundamental effect on the resulting shock wave propagation. Typically researchers use a spherical or hemispherical geometry in order to simplify the shock wave so that resultant overpressure and impulse are uniform in all directions. The goal of this research is to understand the overpressure characteristics from a sheet explosive, a geometry often utilized for breeching in the military. In training alone, soldiers can be exposed to several tests per day, which may be contributing to the prevalence of blast induced mild traumatic brain injuries. Using PCB pressure transducers and high speed video, it was found that as the angle departed from normal (perpendicular) to the face of the sheet explosive, the over pressure decreased significantly. When in line with the plane, a decrease of over pressure by as much as 20% was observed. Time of arrival was roughly 20% faster directly in front of the charge with a pressure amplification of 46% relative to a spherical baseline charge of the same mass. This testing may reveal a more complete relationship between the pressure and angle from the explosive that could have applications for military and law enforcement with respect to best practices on blaster location for reduced over pressure exposure.

Jan 1, 2019

By J. Um, B. Morin, P. H. S. W. Kulatilake

Development of a three-dimensional mine visualization model for a section of the mine is addressed first. Discontinuity orientation and location information was taken from this visualization model for use in slope stability analyses. Estimated shear strength properties of discontinuities and mechanical properties of intact rock from the rock mass samples obtained from the mine are discussed next. The paper is then focused on the calculated maximum safe slope angles based on the performed kinematic and block theory analyses using the mapped discontinuities at the mine. Finally, the effects of water that exist in the rock mass, tension cracks, slope face inclination, overall wedge height and double benching on factor of safety of wedge stability are illustrated through limit equilibrium slope stability analyses.

Jan 1, 2002

By Gavin J. Faulkner

This paper presents an investigation of some alternatives, and improvements to timber posts and cribs. The purpose is to find a cheaper, better, easy to install, and effective means to replace or improve them. Selection of supports needs to take account of several factors. These factors include the mechanical behavior of the support, technical feasibility, and cost. In this paper a variety of supports are compared on these bases. Particular advantages and disadvantages of those supports have been determined through published material and a testing program. A broad evaluation of a number of specific groups of supports is presented. Included in this evaluation are timber posts and cribs, steel friction props and several, newer developments such as the Micon Yield Capsule and the Super Post. Another support that will be briefly discussed is steel-fiber-reinforced concrete. Particular emphasis will be placed on the Micon Yield Capsule and the Super Posts on which preliminary testing has been carried out. The testing results are presented in detail. The shortcomings of the test procedure are pointed out and some new ideas to improve the testing in the future are proposed.

Jan 1, 1986

Because of complex geological environments, a number of coal reserves occur in inclined or dipping coal seams in certain parts of the world. Longwall top coal caving using split-level a singleentry panel system (SSPS) has been widely used for extracting such coal seams with large thicknesses (greater than 6 m) in China because SSPS can reduce or mitigate problems of coal outbursts, gate road deformations, overturning of shields, downhill sliding of shearer and armored face conveyor (AFC), and so forth, during mining of inclined coal seams. Depth of yield is the range of yield coal from the rib of the pillar to the boundaries where yield ends. It plays a significant role in maintaining the gate pillar stability. This paper presents a study on the stability of an unconventional water-obstruction gate pillar (UWGP) formed by SSPS to prevent water inrush in mining of an inclined thick coal seam in a coal mine in China. As the shape of this pillar is non-cuboidal, nonparallelepiped, a conventional empirical or analytical method is not applicable for studying its stability.

Jan 7, 2020

By N. Demirel, O. Gölbasi

Draglines are massive machines extensively utilized in opencast mines for overburden stripping. The demanding working environment induces fractures, wear and tear, and fatigue failures in dragline components and eventuates in extended maintenance, lengthy downtimes, and loss of production. The bucket is the main source of external loads on the machinery, since interactions with ground materials take place in this region. This study aims to develop a generic finite element model of the stress on an operating bucket. This entails (i) three-dimensional modelling of a dragline bucket, (ii) analytical estimation of resistive forces in the bucket movement, (iii) three-dimensional simulation of the moving bucket using finite element analysis (FEA), and (iv) sensitivity analysis to examine the effect of formation characteristics on stress variation. Simulation results imply that the drag hitch and digging teeth are the elements of the bucket that are most prone to failure. In addition, sensitivity analysis indicates that internal friction angle of the formation is the dominant parameter leading fluctuations in stress values. Changes in stress level are least influenced by formation density.

Jan 1, 2015

By J. Martinovic

The large proportion of gangue minerals present in platinum bearing ores in South Africa provides challenges to the flotation and downstream processes. In order to take effective measures to reduce their recovery in flotation, an understanding of the mechanisms and factors influencing their behaviour is needed. Typical gangue minerals are pyroxene, feldspar, quartz, chromite and talc. Of these, talc is a naturally hydrophobic mineral and although it is present in relatively small quantities, it has a disproportionate effect as it has a strong froth stabilizing effect, increasing the recovery of other gangue minerals by entrainment. Talc recovery is effectively reduced with the addition of polymeric depressants. Although the other gangue minerals are assumed to be hydrophilic and their recovery by entrainment is expected to follow the water recovery, there is some evidence that they may be activated by the typical reagent suites used. Reagents such as copper sulphate, added as an activator, and collectors are used to selectively induce hydrophobicity on the sulphides. It has been shown that some of these gangue minerals can be activated. This research work investigates whether inadvertent copper activation is mineral specific and evaluates the mechanisms and factors affecting the reversal of activation with the addition of the depressants using electrokinetic measurements, adsorption and microflotation tests. Results are presented that show that the selected minerals do respond differently and that the reversal of activation is dependent on mineral type, depressant type, dosage and ionic strength of the electrolyte.

Jan 1, 2005

The kinetic and practical aspects of the extraction of copper from copper-rich solutions by cementation on iron was investigated. Tests were made on the effect of stirring speed, cupric sulphate concentration, acid concentration, temperature, and ferric sulphate concentration on the reaction rate and excess iron consumption.Most kinetic investigations were conducted under a nitrogen atmosphere to prevent any oxidation of the iron or copper metals. The stirring mechanism for all tests incorporated the use of a rotating impeller above a static disc in the solution. The activation energy for cementation on the steel disc at high stirring speed was 8·6 kcal/mole, indicating a predominant chemical control.Increasing the pH first decreased, then above pH 3, increased the reaction rate. Additions of sodium sulphate also significantly increased the reaction rate.The use of high temperature and high pH under an inert atmosphere has been suggested for increasing the reaction rate and producing a high purity sponge copper product.

Jan 1, 1972

By J Steyn

Block Cave mining is one method used to extract ore from underground diamond mines as well as other massive orebodies such as copper. This necessitates the excavation of many kilometers of tunnel within the ore body. The integrity of these excavations needs to be maintained over a number of years. Most Kimberlites and weak orebodies are extremely susceptible to degradation when exposed to moisture and the atmosphere. It is therefore essential that some form of weathering protection is applied as soon as possible after exposure. Conventional methods of weathering protection such as shotcrete do not easily fit in with the production schedule, hence the need for a more efficient system that could be applied immediately after exposure and serve as a temporary support or even as a permanent support medium. The main advantages of thin sprayed liners (TSL) compared to shotcrete are the ease of application, speed of application, early strength, much reduced transportation of material, less labour intensive and cost effectiveness. Several Thin Sprayed Liners suitable for various mining environments and geotechnical conditions are available and could be well suited as additional support the undercut level development in a block cave where this may be required. TSL offer a cost effective support solution as an alternative to shotcrete in areas where the building of a support structure is not a requirement.

Jan 1, 2008