Search Documents

By N. Yamazaki

The supply of clean copper ores, which have high copper concentration and low impurities like arsenic, has declined year by year. Therefore, both mine and smelter sides have to consider how to remove impurities like arsenic. We focus herein on arsenic as an impurity because it is an extremely important issue from the environmental point of view. Approximately 150,000 t of arsenic is input into the copper industry every year. A small part of it is mainly treated in the smelting side. For instance, Ministro Hales Limited, which is a mining corporation in Chile, has performed the calcination process to remove arsenic from ore with high-arsenic content. In the process, flue gas is washed by water, and the final residue is treated by a hydrometallurgical process. Many processes for arsenic removal in various stages have been proposed, and several bottlenecks exist to achieve it. One of the difficulties encountered is getting an assessment of the process, which depends on the countries and/or areas of operation. The standardization of the assessment procedure will be desired in the near future to keep the same environment standards all over the world, and now is the time to start making discussions on this matter. This will be the first step in making an international assessment procedure for arsenic treatment in the copper industry. INTRODUCTION Using the term “sustainable development” without any scientific basis can give people a false sense of security. Engineers and scientists must analyze the total mass flow of energy and materials and estimate local drain on the environment as well as the global impact of a particular industrial activity to ensure sustainability on this planet. The operations of the mining and smelting industries have a strong effect on the environment even if they provide useful materials for human beings. The copper mining and smelting industries have brought about serious environmental problems in the past. For example, the Ashio mine pollution caused big damage to the agricultural sector near the Ashio area in Japan in the late 19th century. One of the most serious problems at that time was SO2 emission because copper ore is sulfide, and the smelting process basically results to sulfur oxidation. The resource balance from a copper smelter in a year, assuming a total production of 16 million tons, can be summarized as follows: discarded minerals, 30 billion tons; sulfur, 16 million tons; iron oxide, 8 million tons; additional smaller amounts of other metals, electricity, and fuel.

Jan 1, 2019

By Jeffery L. Dean

Founded in 1974, the ISEE has grown to more than 3600 members representing 72 countries. The Society and its 35 chapters in the US, Canada and Australia promote research and education, provide forums for the exchange of explosives technology, serve as a repository of explosives information, provide expert help to governments, conduct certificate/training programs, and promote the teaching of the safe and controlled use of explosives.

Jan 1, 1997

By E. Nickel

"Bi- and multilateral banks as well as export credit agencies in the OECD countries, but also numerous commercial banks, last year committed themselves to compliance with the World Bank’s standards. These environmental and social guidelines, also known as the Safeguard Policies, are the strictest international standards in the area of financing of major investment projects. The Safeguard Policies are procedural and quality guidelines by means of which socially and environmentally relevant impacts can be taken into account in the planning and implementation phase of a project. Objectives of the Bank Safeguard Policies are to ensure that environmental and social issues are evaluated in decision-making, to reduce and manage risk of projects and programs, and to provide a mechanism for consultation and disclosure of information. They are often referred to as the "10+1 Safeguard Policies," since ten of the guidelines address environmentally and socially relevant issues, while one guideline is exclusively concerned with public participation ("Public Disclosure"). In the presentation, the transparency of risk management measures and emergency response plans in pipeline projects will be discussed as an indicator of sustainability. The discussion is to be carried out on the basis of the results of an evaluation of several major pipeline projects, which have been financed at least in part by multilateral banks over the past few years. The controversies surrounding some of these projects due environmentally and socially relevant impairments connected with the investments have also been addressed by the Extractive Industry Report of the World Bank. Pipeline construction was the investment type chosen for the examination to be presented here, since pipelines frequently start in remote, unspoiled regions, and their routes often cross various natural zones and areas with various social structures. The question of safety during construction and operation of the line is always central to these projects; not only for the responsible authorities but also for other societal groups involved, such as environmental associations."

Jan 1, 2005

By Richard Hosley, James Daley

Every grey haired member of the explosive’s industry has said at least once, “We have to get some younger blood into our industry, I might want to retire someday.” And many a youngster who loves to see explosions has wondered how to get involved in such an exciting, yet intimidating, industry. While there are many answers to these questions, an internship program is a great answer to both

Jan 1, 2014

By Reichardt Y

Fine feed fractions in the size range from 1 to 40 ¦m of materials with different hardness as limestone and silicon carbide have been stressed in two different devices. A tungsten-carbide-blodc allows a single stressing with a pressure up to 2000 MPa and a 4-piston-block enables a multiple stressing procedure in which the material bed is stressed in alternating directions with a pressure up to 700 MPa. The experiments show energy absorption as the major factor for the interparticle breakage of hard material, like quartz, zircon silicate, silicon carbide and smelted oonindum, pressure, however, does not influence the results within the investigated range from 100 to 700 MPa and even up to 2000 MPa for corundum. But the breakage of the middle-hard limestone depends on the pressure so far as more fineness can be produced if the same energy is introduced at a lower pressure level. The creation of very fine and microfine fragments decreases strongly with increasing hardness of the feed materiaL The energy consumption for producing microfine material with a multiple stressing procedure on a particle bed is much lower than that one of a usual milling process. But this procedure needs a classification with a seperation cut at a couple of microns, which is not easy to accomplish.

Jan 1, 1993

By Y. Guglielmi, V. Merrien-Soukatchoff, I. Kadiri

ABSTRACT: Hydraulic experiments have been conducted since 1997 within a small fractured calcareous rock mass in southeastern France, at a site called Coaraze. On this reduced-scale site closing a floodgate located on a downstream spring produces repeated hydraulic loadings. Simultaneous measurements of normal deformations and pressure in several joints have provided a better understanding of the hydromechanical behaviour of such a fractured rock mass. The present paper first describes both the site and conceptual interpretation of the measurements performed. We showed that accurate measurement reproduction requires incorporating certain features: a variable normal joint stiffness, the joint vicinity (through introducing a Z coefficient), and the initial stress state. The paper then develops an original analytical interpretation of the coupled pressure-displacement measurements carried out, which reveal the high level of measurement suitability to the non-linear behaviours examined. 2D modelling, using the discontinuous code (UDEC) was used to proceed with the calibration step. KEY WORDS: In situ test, methodology, hydromechanics, modelling, non linear behaviour ZUSAMMENFASSUNG : Hydromechanische Experimente werden seit 1997 in einer kleinen Kalksteinmasse, das sich im Südosten von Frankreich befindet durchgeführt. In diesem kleinen Standort, werden wiederholte Wasserdruck Erhöhungen durch das Schliessen eines Hahnes produziert. Gleichzeitiger Druck und normale Verformung Meßungen in mehreren Fugen haben erlaubt, das hydromechanische Verhalten einer solche gebrochene Felsenmasse besser zu verstehen. Der Artikel beschreibt zuerst den Standort und stellt die begrifflichen Interpretationen der Meßungen vor. Um die Meßungen gut zu reproduzieren ist es wesentlich, bestimmte Faktoren wie die veränderliche normale Steifheit der Fugen, die Nachbarschaft der Fugen (über einen Z-Koeffizient) und der Spannungstand zu berücksichtigen. Der Artikel erklärt die originale Methode für die Druck- und Verformungs-Meßungen Interpretation und zeigt die gute Korrelation der Meßungen mit dem nicht-linearen angenommen Verhaltens der Fugen. Die numerische 2D-Modellierung mit dem UDEC Software ist für die Verkeilung der Faktoren gebraucht worden. SCHLÜSSELWÖRTER: In-situ-test, Methodologie, Hydromechanik, Numerische Modellierung, nicht-lineares Verhalten RESUME : Des expérimentations hydromécaniques sont conduites depuis 1997 dans un petit massif calcaire fracturé situé dans le sud de la France. Dans ce site de taille réduite des mises en charge répétées sont produites par la fermeture d'une vanne située à l'aval du site. Des mesures simultanées de déformation normale et de pression dans plusieurs joints ont permis de mieux appréhender le comportement d'un tel massif fracturé. L'article décrit dans un premier temps le site et présente les interprétations conceptuelles des mesures. Pour bien reproduire les mesures, Il est essentiel de prendre en compte certains facteurs tels que la raideur normale variable du joint, le voisinage du joint (par l'intermédiaire d'un coefficient Z), l'état de contrainte initial. L'article précise la méthode originale d'interprétation des mesures pression-déplacements qui montre la bonne adéquation aux lois de comportement non linéaire proposées. La modélisation 2D, à l'aide d'un code discontinu (UDEC) a été employée pour le calage des facteurs. MOTS-CLEFS : In-situ, méthodologie, hydromécanique, modélisation, comportement non linéaire

Jan 1, 2003

By Redman P. G, McMahon B. K

A simple technique for evaluating the field stress ratio is presented, based on the results of extensometer or convergence tape measure- ments taken in an advancing tunnel. This tech- nique also yields a value for the rock mass modulus, provided Poisson's Ratio is assumed. The results of two case studies are presented illustrating the effectiveness of the method.

Jan 1, 1981

By G S. Lane, G D. Richmond, J Dioses

This paper discusses the methods used in the design of flotation plants, including benchscale batch and locked cycle tests and pilot plant trials. Two case studies are presented, one for the Cadia Hill Gold Mine and the other for the Hellyer copper, zinc and lead plant. These case studies present different problems with widely different target grind sizes, liberation characteristics and HellyerÆs sequential flotation circuit versus CadiaÆs æsimpleÆ copper/gold flotation circuit. They have a common theme in that pyrite forms the principal floatable concentrate diluent. Hellyer ore contains finely disseminated chalcopyrite, sphalerite, galena, and tetrahedrite. The flotation plant design was based on extensive benchscale testwork (including locked cycle tests) on drill core and many months of operation of a 30 tonne per hour æpilot plantÆ, using the old Cleveland Tin Mine process plant suitably modified for the duty. The Cadia concentrator was designed on an extensive benchscale variability testwork program, approximately a dozen locked cycle tests conducted on drill core and two weeks of continuous pilot plant trials on three separate samples obtained from an adit into the orebody. The orebody is a monzonite porphyry with disseminated chalcopyrite/bornite/pyrite of very low grade (0.17 per cent Cu, 0.73 g/t Au). Methods used to establish the appropriate flotation circuits for the treatment of the Hellyer and Cadia ores, as well as the interpretation of the testwork data, are discussed in this paper. Plant performance is reviewed in the context of predicted versus operational performance.

Jan 1, 2002

By B. A. Comley

Over the past few decades a great deal of effort has gone into characterizing the effects of frother type and concentration in flotation using a variety of two-phase techniques. Whilst useful and informative, this research still does not assist in the selection of suitable frothers for three-phase industrial-scale froths. This paper investigates the effects of frother type and concentration in a three-phase industrial froth. The objective was to determine if progress could be made in terms of understanding the behavior of frothers in flotation and understanding how they affect the sub-processes occurring in the pulp and froth phases and, ultimately, the metallurgical performance of a flotation cell.

Jan 1, 2007

By Timothy C. Siegel

Accurate representation of the geotechnical resistance distribution is critical in evaluating the performance of piles and pile groups for design. A current practice is to infer the geotechnical resistance distribution based on measured changes in strain during conventional top load pile testing. Especially for drilled and bored piles, the residual load is typically assumed to be negligible both during testing and after the application of the structure load. A practical result is that the compressive structural load is anticipated to be opposed primarily by the shaft resistance with little or no mobilized toe resistance. The predicted top deflection is estimated as the combined elastic compression plus the movement necessary to mobilize shaft resistance. The development of residual load (and associated negative skin friction) results in a significantly different design condition. Negative skin friction tends to force the pile into the ground and develops residual load in the pile that contributes to the internal compressive load. Significant toe resistance can be mobilized in order to resist the combination of negative skin friction and the sustained compressive load. The pile movement becomes a function of the toe penetration required to mobilize sufficient resistance to reach a balance of forces. In an effort to study the development of residual load in augered cast-in place (ACIP) piles, the authors installed and monitored strain gages that were embedded in an 18-inch diameter ACIP pile at a site in southeast Georgia. The results of this study indicate that residual load develops over time and reaches a distribution that is consistent with the principles of the unified design of piles. It is concluded that residual load develops in ACIP piles (as well as all drilled and bored piles by the same mechanisms) and that the residual load should be considered in the interpretation of load tests and in the pile design, particularly in the estimation of the single pile and pile group settlement.

Jan 1, 2009

By Bruce Vandenberg

Two tests were set up as part of the course given by Blasting Analysis International. Both tests were performed using the prototype Velocity of Detonation Recorder (VODR). The prototype has several limitations, which have been rectified for the production units.

Jan 1, 1990

By John E. Wiegand

"We will attempt to explain the basic workings of a modern seismograph and how the recorded data can be interpreted, not only for determining compliance to the regulations, but also in determining whether or not a seismograph record is accurate and valid. We will discuss some parameters that should be included in all seismographic recordings. We will give examples and use overhead slidesto show examples of both accurate and valid recordings, and tampered and inaccurate seismograph recordings. Much of the information presented will be basic in nature, and will reflect the opinions and personal experiences of the author. We ho'pe the listener will gain valuable information concerning the use and interpretation of seismographic data, as well as find interest and sometimes humor in the examples shown."

Jan 1, 1992

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2006

By J. G. Wiese

Reagents are added to the flotation process of Merensky Reef ores to achieve specific functions that enable the separation of valuable minerals from gangue minerals on the basis of the difference in their surface properties. However, due to the complexity of the process, the various interactions that occur as well as the incomplete liberation of the ore and range of minerals present, it is difficult to quantify the behaviour of each of the reagents. More specifically, changes made to achieve a particular outcome may have secondary effects that can override the desired effect. If all the effects and interactions can be accounted for, it is possible to manipulate reagent suites and obtain better overall metallurgical performance. This paper discusses the effect of the addition of copper sulphate at different operating points of the recovery of the sulphide minerals. Batch flotation tests indicated that the recovery of chalcopyrite was not affected when operating conditions were varied, whereas pentlandite recovery was strongly affected by the point of reagent addition, and pyrrhotite recovery was enhanced by copper sulphate addition, irrespective of the point of addition, with the extent being dependent on the ore source. Floatable gangue was activated by copper sulphate in the presence of the dithiophosphate collector. Froth stability was also affected by copper sulphate addition.

Jan 1, 2007

Landscape interpretation, geology and mining history is being successfully used to explore options for sustainable community tourism product development. Recent work by the author in Europe and Australia has indicated the value of adding and producing interpretive information about mine and quarry locations - both active and inactive. This work has allowed for the branding and development of new sustainable community tourism products based on the landscape, folklore, mine and geological heritage.   Communities in rural areas are seeking new opportunities to sustain their local economies. Using a relatively new phenomenon called geotourism as a starting point; they have developed themed products connected to walking/cycling guides, interpretive panels and visitor centres. These themes can be linked to geology, archaeology, botany, local history and to industrial heritage sites such as old mines, to generate local employment. This new geotourism approach has successfully brought a new and greater audience to discover the value of geology and mining history.   Communities have established a unique place for themselves within the tourism marketplace using the geotourism brand. Other communities with an established tourism product are also now using geological and mine heritage via geotourism to rebrand and meet changing global trends. The pooling of resources under the banner of geotourism has led to cost effective marketing, targeting and promotion of products.   Geotourism has emerged strongly in Europe, North America and China in the last decade. The Australian minerals industry now has an opportunity to implement this new branding concept to assist and benefit the communities in which they run their activities. Communities can also take advantage of the potential to develop a sustainable geotourism business around a past or present mineral industry in their vicinity.

Jun 1, 2010

By Robert M. Valentine, Randall L. Lentell

Interpretive geotechnical investigations were performed for the construction of approximately 15,250 m (50,000 ft) of wastewater interceptor tunnels in Austin, Texas. Subsurface materials consist of claystone (or clay shale), siltstone, altered volcanic tuffs, chalk and limestone. Special conditions include multiple crossings of Onion Creek with cover ranging from about 1/2 to 3 m (2 to 10 ft.), and the potential for mixed-face conditions consisting of water-bearing gravels overlying clay shale or siltstone. The methods and results of the geotechnical investigations are discussed and the inferred construction conditions are compared to those encountered during tunneling. A suggested format is presented for interpretive geotechnical reports for underground construction projects.

Jan 1, 1985

By Lev Filippov, Vyacheslav Severov, Inna Filippova

"Reverse cationic flotation is a very efficient method of beneficiation of oxidized iron ores when you need to separate hematite and quartz. This method can be also applied to reduce silica content in the magnetite concentrates obtained by wet low-intensity magnetic separation. However, cationic flotation in this case is less effective due to the presence of Fe-Mg-Al-bearing silicates as amphiboles in magnetite ores. These silicates are concentrated in magnetic products and determine the difficulties of their separation from iron oxides when amines and starches are used as collectors and depressants, respectively. The recalculation of the results of the electron microprobe analysis of three calcic Fe-Mg-Al-bearing amphiboles used to characterize cation distributions in structural units and to obtain structural formulas in accord with stoichiometric limits was conducted. The Mössbauer spectroscopy was used to examine the validity of the empirical estimation of cation distributions in amphiboles. The studied samples are metamorphic pargasite and ferrotschermakite and volcanic magnesiohornblende. The crystallographic analyses of the amphibole samples exhibited their heterogeneous surfaces explaining worse floatability of amphiboles with dodecylamine at pH 10. The electrokinetic measurements showed that the position of the isoelectric point of amphiboles is related to a substitution of Al3+ for Si4+ in tetrahedral sites and to an amount of Mg2+ cations in octahedral sites. Thus, the dodecylamine adsorption onto amphiboles through electrostatic interactions is mainly affected by a distribution of these cations in tetrahedral and octahedral sites of amphiboles. In addition, the effect of starch on the depression of Fe-Mg-Al-bearing amphiboles during flotation can be attributed to the presence of metal ions on the amphibole surface, which are capable of forming strong chemical complexes with starch molecules."

Jan 1, 2014

By Ray Schmahl

The Glenwood Canyon is a 13 mile long river gorge formed by the Colorado River approximately 2 miles East of Glenwood Springs, Colorado and approximately 150 miles West of Denver Colorado, (See Drawing #1). The canyon walls rise some 800 feet from the river elevation on either side of the river. The South-side river bank is occupied by the Denver and Rio Grande Western Railroad. The Northside is currently occupied by completed sections of Interstate 70 and US Highway 6. The railroad was built in the late 1800's and a hydroelectric power generating station was built in about the center of the canyon in the early 1900's. The Highway 6 platform was completed in the 1930's. The design and alignment for Interstate 70 thru Glenwood Canyon began in the early 1970's. The Highway thru Glenwood Canyon was designated a scenic Highway by the United States Congress, thereby allowing certain deviations from standard Interstate requirements. Environmentalists objections to the construction of Interstate Highways thru Glenwood Canyon resulted in especially careful design to avoid adverse environmental impacts. As a result, in many areas the new Highways will have restored the canyon to its more native configuration than what was the case in the building of the US 6 Highway platform.

Jan 1, 1990

By S. Akhtar

Interstitial compounds of iron, cobalt, and nickel, and their binary and ternary mixtures with silver, gold, palladium, and platinum were prepared and tested as fuel cell catalysts. The first step in the preparation of the interstitial compounds consisted of preparing finely divided metals. This was done either by the Raney method or by reduction of precipitated hydroxides of the metals. The finely divided reduced metals were then treated with carbon-and/or nitrogen-containing gases to prepare their carbides, nitrides, and nitrocarbides. The materials were tested for cathodic activity towards O2 and for anodic activity towards H2, C3H8, NH3, CO, and N2H4 in acid and alkaline electrolytes at 25° to 90° C in half-cell assemblies. Samples of carbided and nitrocarbided INi-lAg-1Au were about one fifth as active as Pt-black in the reduction of O2 in 35 percent KOH solution, whereas the activities of several interstitial preparations exceeded the activity of Pt-black in the reduction of O2 in 12M KOH containing N2H4. Nitrocarbides of x-Fe2C, 3Ni-1Au, and 1Ni-3Au were effective catalysts for oxidizing N2H4 in liquid NH3 containing NH4SCN. Corrosion of the catalysts by electrolytes was severe in many cases.

Jan 1, 1970

By D. Tesh

The mining industry worldwide is facing a tremendous shortage of minerals engineers in all fields of specialization. For instance, in Australia the skills shortage in the mining industry has been identified as one of the top risks facing the mining industry. In Namibia most minerals engineers employed are expatriates, with some being Namibians who studied abroad. The minerals engineering programmes at the Polytechnic of Namibia are still in their infancy. These programmes were designed to meet the mining industry skills needs. Being young has its advantages in that lessons can be learnt from older minerals education institutions that went through similar challenges. However, this does not imply just copying and implementing their approaches, since the context differs and, to ensure sustainability of the minerals education programmes, curricula have to be customized to the local context. This paper reviews the interventions made by the Polytechnic of Namibia in order to ensure the sustainability of its minerals education programmes. The methodology consisted of an extensive literature review, a status quo analysis of the mining and process engineering department, identifying the gaps between the current state and desired state, and mapping the goals and strategic actions required to progress to the desired state. The following factors were identified as major threats to the sustainability of minerals education at the Polytechnic of Namibia: the quality of students, low student enrolment rates, low pass rates in science and mathematics, shortage of academic staff, dwindling government funding, and limited involvement of the mining industry. The major outcomes of this research comprise the detailed strategic actions employed by the Polytechnic of Namibia to address the threats to sustainability of its minerals education programmes.

Jan 1, 2014