Search Documents

By T. Bhambhani, D. R. Nagaraj

"Ultramafic Ni ores present significant challenges in processing in that both recoveries and grades are not satisfactory, due to the presence of Mg silicates in large amounts. Significant quantities of xanthates and CMCs are generally used for their recovery by flotation. Additionally, given that some of these ores are processed under acidic conditions, CS2 generation due to xanthate decomposition presents some safety hazards. Technology to replace xanthate has been developed for which the safety and health issues are absent. Collector S-10294 shows significant improvements in Ni and overall S recovery at a dosing rate of one half that of xanthate. New polymeric modifiers have also been developed that help reduce the Mg content of the concentrates at very low dosages. The reagents are custom designed for use in normal or hypersaline water, and acid or alkaline conditions.INTRODUCTION The use of xanthates in sulfide mineral flotation is reported to have started as early as 1925 (Nagaraj 2005). The reagent is now ubiquitous in the mining industry, accounting for 40-50% of total collector consumption. In recent years, the development of more selective reagents has rendered xanthates largely obsolete in Cu flotation. However, xanthates continue to be sold in large amounts in the Au, PGM and Ni flotation industry, where bulk sulfide flotation is required. The low cost and easy availability is the largest driver for the use of xanthates in the minerals industry. Of particular interest to this study is the use of xanthates in the flotation of Ni sulfide ores. About 60% of the world’s annual nickel output is obtained from sulfide Ni ores (Hoatson, 2006). A strategically important category of these ores is the ultramafic hosted sulfides, such as those of Western Australia and Canada. These ores are characterized by low Ni grades (<1%), with the Ni minerals being pentlandite, violarite, millerite and mackinawite, and gangue minerals comprising an array of altered Mg silicates, mostly serpentines. The challenges associated with treating these ores are well documented (Eltham et al. 1973; Claridge et al. 1975). One challenge is that Ni recoveries from these ores are lower. This has been attributed to the increased pulp viscosity, as discussed in detail by Vasudevan et al., 2010. Additionally, Mg silicates tend to report to the concentrate in large quantities, which is problematic for two reasons: a) concentrate dilution, and b) the high melting point of Mg silicates tends accelerate wear on the refractory lining of smelters. This has been attributed to network transport to the froth phase via bubble flux and entrainment (Patra et al, 2010)."

Jan 1, 2012

By Carl-John Grävare

This paper deals with some of the systems and equipment that are being developed and/or are in use in Scandinavia. The main subject is the development of loading tests on the piles using monitoring equipment. This paper also describes ground improvement using lime-cement columns, expander body piles and steel core piles.

Jan 1, 2000

By Robert B. Bittner

"AbstractLarge diameter tubular piles offer significant advantages in terms of design performance and economy for major marine structures. This is particularly true for foundations of major overwater bridges in regions of high seismicity such as the west coast of North America. The use of large diameter piles in the range of 2 to 3 m diameter means that fewer piles are required, and the size and mass of the pile caps can be significantly reduced, thereby greatly reducing lateral load demand during seismic events. Another advantage of using larger diameter piles is increased pile stiffness that allows the pile caps to be located at or near the waterline rather than being positioned at or below the mud line. This elevating of the pile cap offers significant cost savings by eliminating the need for deep cofferdams. However, relocation of the pile cap creates new problems and opportunities in regard to the means and methods used to construct the pile cap. With the pile cap at depth, conventional steel sheet pile cofferdams with thick tremie seals are typically used to isolated the cap location and allow dewatering for construction of the cap. However with pile caps positioned up off the bottom, conventional bottom founded cofferdams are no longer cost efficient. Float-in or lift-in cofferdams have been developed to address the need for a more cost efficient method for cap construction. This paper describes the key features of the concept and provides three case history examples of its successful implementation.Pier Construction Using Conventional Sheet-Pile CofferdamsCofferdams are temporary structures used in the construction of bridge piers and other marine structures. Their primary purpose is to hold out water and unstable soil from the construction area, and thereby, allow in-the-dry construction of the permanent structure below the water line and quite often below the mud line. Typically, cofferdams consist of long interlocking steel sheet piles driven through water into the bottom of the waterway. The sheet piles form temporary exterior walls which are typically braced internally with wales and struts. The bottom of the cofferdam is typically sealed with tremie concrete or an impervious clay layer if one exists. The depth at which this type of cofferdam can be used is typically limited by the length of steel sheet pile that can be transported and handled by conventional marine equipment."

Jan 1, 2014

By Darrell Gillis

Recent accidents in the United States underground Coal Mines and the on-going carnage in Underground Chinese Coal Mines has shown the danger associated with the lack of communication infrastructures in an underground environment. The US Mine Safety and Health Administration (MSHA) have introduced legislation that states all Underground Coal Mines must have two-way voice and personnel tracking capabilities by 2009. If Coal Mining companies are being forced to deal with this problem Tunneling Companies will not be far behind. This paper will examine current practices and best case technology to deal with these issues.

Jan 1, 2007

Innovative and Resource-Preserving Washing Processes for Primary and Secondary Raw Materials

Sep 13, 2010

By B. Leong, H. Joubert

Keywords: Pyrometallurgy, furnace, auxiliary equipment, copper slag launders Pyromet has designed copper launders for tapping slag. What makes Pyromet?s launder design innovative and safe is that it does not have any cooling water channels underneath the launder runner, whilst achieving effective cooling of the runner. If matte burn-throughs were to occur through the launder runner, the risk of damaging water channels and the risk of explosions are reduced. In addition, since the cooling water channels are not harmed, the launder is easily repairable and reusable. Pyromet makes use of Finite Element Analysis to optimize the launder geometry to ensure that sufficient energy is removed from the centre of the launder. Factors considered during the launder design include the suitability of the geometry to the client?s needs, experience from existing installations, and ease of fabrication. Pyromet goes so far as to develop procedures for fabricators to ensure that fabrication issues do not compromise the functionality of the launder. When launder orders are received by Pyromet, the entire fabrication process and the functioning of the launders during operations are monitored to ensure that the launder designs are continuously improving with every installation.

Jan 1, 2006

By Y. El-Mossallamy

The piled raft foundation was extensive applied in the last two decades in different soil conditions e.g. in soft to stiff clay as well as in medium to dense sand and even in highly weathered rock. The piled raft is now applied not only to control the foundation settlement but also to minimize the required raft thickness to reach the most economic foundation design. An innovative application of the piled raft is its special adjustment to cases of foundations with large load eccentricities or very different loaded parts of buildings to avoid the need of settlement joints, which are especially complex below ground water table. Recently, the piled raft is applied for foundations of highway and railway bridges with special serviceability requirements regarding the allowable total and differential settlement as well as tilting. Actually numerical analyses are the mostly used design methods for piled rafts. For all day design practice a simple and modest design method is highly needed -at least in the first design stage- to check the feasibility of the piled raft on the specific project conditions. In this paper, a general overview on the recent innovative applications of piled rafts in Germany will be presented in a short overview. The results of the simple design method will be discussed and compared with the results of more enhanced numerical methods.

Jan 1, 2006

By Askew JE

The large, massive low grade gold orebody at Mount Charlotte has demanded an innovative approach to mining engineering. In the last five years several advances occurred in the areas of rock mechanics, mass blasting, blasthole drilling and truck haulage.Successive crown pillar failures throughout the life of the mine had resulted in a continuous geotechnical program, mostly utilisingconsultants. The culmination of this workwas the development of a successful crown pillar support system. Several stopes have incorporated the technique and the most notable success has been the relatively large F3 crown pillar.In hole hammer drilling was introduced to the mine in 1979, but little work had been done to develop a blasting system to suit the 165mm diameter holes. A non-electric sequential blasting system was adapted for use at themine and up to 600,000 tonnes have been fired successfully in an individual blast. Problems with ground vibration were addressed although this work remains incomplete.

Jan 1, 1984

By G. Hames, A. Drake, B. Sampson

The Timbarra opencut gold mine is located about 30 km(19 miles) southeast of Tenterfield in northern NSW some 4 hours by car from Brisbane, the capital city of Queensland in Australia. It was a small operation designed to produce about 40000 ounces of gold per annum utilising contract mining and company owned crushing plant feeding heap leach pads. This is a standard setup except that the mine owner was in charge of all aspects of drill & blast design even though a contract drilling & blasting (shotfiring) service was being provided. The major problem was that the blasting operations were yielding massive amounts of oversize due to the jointed partially weathered nature of the granite. This was adversely affecting all downstream aspects of the operation as well reducing gold output as ore boulders were being dozed over the side of the mine as they were impinging on mining productivity. The oversize problem had to be solved as the mine was struggling to achieve design gold output. Significant design & trialing effort using minesite resources were utilised to reduce the oversize but this failed even when powder factors up to 1kg/bcm(1.68lb/yd) were used. Dyno Consult from Dyno Nobel were therefore called to investigate, review & trial options to reduce oversize from the top flitch.

Jan 1, 2003

By R. Bitmead, R Barker, A. Drake

The opencut coal mine is located about 50 km west of Brisbane, the capital city of Queensland in Australia and produces about 140 000 tonnes per annum of high grade steaming coal utilising a small team (ten) of personnel to mine remnants of the Aberdare and Bluff seams left by previous underground mining. This, in itself, is not remarkable except that one of the seams has commenced spontaneously cornbusting resulting in temperatures in excess of 55’C commonly being encountered with portions of the p’it being wreathed in steam. To extend mine life, the mine required a blasting system that would: . Safely blast in temperatures below 100°C . Significantly reduce overall unit costs . Not increase the current vibration impacts on nearby housing . Not increase flyrock.

Jan 1, 2002

By Robert Bittner

The following is a report on the development of two unique and separate cofferdam systems used in the construction of the marine foundations for the I-205 Columbia River Bridge at Portland, Oregon for the Oregon Department of Transportation. The first of these two systems utilized interlocking H-pile 100 ft long to form a cofferdam 145 ft by 58 ft in plan and 100 ft deep. The second system consisted of two immense bell shaped steel forms. The larger of the two forms was 83 ft by 66 ft in plan, 62 ft high and weighed 450 tons. This form was externally stiffened for a designed hydrostatic head of 54 ft. Both forms were designed, except for the top 14 ft, to be set and stripped in one solidly welded unit. The supporting geological formation for the bridge foundations is the Troutdale, a cemented sand and gravel. This formation is at the ground surface on the Washington Shore and slopes downward to a depth of 115 ft below normal high water at about mid-channel. In this area the Troutdale formation is covered with a layer of fine to medium sand 90 to 100 ft thick. It was the variable depth of the Troutdale which determined the two types of foundations and the corresponding to the two cofferdam systems.

Jan 1, 2013

By Kanchan K. Sen

The North Shore Connector (NSC) project will extend the Allegheny County Port Authority?s Light Rail Transit System from downtown Pittsburgh below the Allegheny River to the North Shore via twin bore tunnels. Jet grouting, diaphragm walls, and soil mixing were selected as cost-effective technically viable ground improvement and support of excavation techniques. Jet grouting was specified to provide break-out (egress) and break-in (ingress) block sections at the tunnel boring machine (TBM) launching and receiving pits. Jet grout treatment was also used adjacent to buildings with shallow foundations and below retaining walls along the tunnel alignment. A new method for measuring jet grout column diameter based on electrical resistivity was employed on the project. New equipment was introduced in the U.S for constructing soil mix temporary support of excavation using a soil-mix technique termed Cutter Soil Mixing (CSM) due to the use of two vertical cutting wheels that have evolved from diaphragm wall trench cutter technology. The system allows for continuous water tight soil mix panel construction including steel beams. This paper highlights some applications of jet grouting and various support of excavation systems (e.g. slurry walls, cement bentonite walls and CSM walls), including new innovative techniques (e.g. Cyljet and CSM) used under the constraints of an urban environment.

Jan 1, 2010

By Thomas Billups, Brendan FitzPatrick, Doug LeDo, David Carchedi

"Working in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. This paper describes the use of the modular Ductile Iron Pile system, a low-vibration driven micropile, on two urban projects on the Johnson & Wales University campus in Providence, Rhode Island. The paper describes the successful implementation of Ductile Iron Piles installed to develop capacity in end-bearing on one site and friction on the second site. Design, installation and quality control operations are all presented as well as the results of full-scale load testing performed on non-production test piles. This paper is of importance to the industry because it describes a versatile option for project teams as an alternative to traditional micropiles, helical piles or other deep foundation systems for urban sites.INTRODUCTIONWorking in urban environments presents unique logistical challenges beyond those typically associated with traditional geotechnical analysis and design. These challenges often include working on sites with limited access and laydown area, vibration concerns for adjacent structures and the need to work from variable elevations or within excavations. Two recent projects in downtown Providence, Rhode Island faced a combination of problematic soil conditions and urban construction challenges including vibration concerns. Both projects were a part of the Johnson and Wales University campus development. Figure 1 illustrates the urban locations of the sites."

Jan 1, 2016

By Jacques Moraille

The public is asking for more aesthetic designs if they can be proven cost-effective at providing an appealing element to new dams. Lake Lenexa was designed and built around the idea of providing for basic dam functions such as flood control, enhanced water quality, recreation but also to provide an inviting community focal point for the residents to visit and enjoy; truly interact with the dam. The architecturally unique dam and ?one of a kind? spillway were designed to symbolize the water cycle as water moves from nature into the urban environment and the back to nature. A pedestrian bridge that spans the spillway offers visitors a good view of cascading pools and a fountain. The original Lake Lenexa dam layout incorporated relatively high, cast-in-place concrete retaining walls to form the spillway structure. The Black & Veatch project team performed a Value Engineering (VE) study to determine cost-effective means for implementing architectural features within the spillway, which resulted in innovative uses of construction materials not typically used in dam and reservoir construction. The VE study concluded that mechanically stabilized earth (MSE) retaining walls that are normally used for transportation projects would be a cost-effective alternative to the originally planned cast-in-place wall systems for the main spillway and stilling basins. The Black & Veatch study added value by mixing cement-kiln dust (CKD) with on-site clay soils to produce a stabilized material for use under the spillway. The CKD stabilized material properties include low compressibility, high strength and low permeability, which reduced seepage and uplift pressures under the spillway slabs. The cost savings provided by the VE alternatives reduced total costs and enabled architectural elements. The award winning dam design also used drilled caissons, expanded polystyrene (EPS) block forms, customized steel forms and external concrete vibrators to build the pedestrian bridge and upper spillway structures.

Jan 1, 2009

By A. J. Hyett

Due to the ongoing revolution in electronics and communications more cost-effective geotechnical instruments can be manufactured using digital technology. This new generation of digital instruments have embedded microcontrollers that provide highly accurate and reliable measurement of geotechnical behaviour in real world units that can be immediately interpreted. Digital measurements can be transmitted across existing mine-wide wireless communication networks, interfaced directly with infra-red enabled PDA?s or PC?s, and parsed to memory by low-cost data-loggers.

Oct 1, 2004

By Aditya Rana, A. K. Mishra, M. M. Singh, N. K. Bhagat

Many cases of derailments, train accidents and traffic interruptions due to the slope failure and rockfall have been reported in the past on Konkan Railway trackline because of unstable rock slopes. The authorities installed stability enhancement measures such as wire netting, rock bolting and shotcreting which were found insufficient. The failed geotechnical measures prompted authorities to excavate the unstable slopes. Rock blasting is generally not preferred for the excavation of slopes along the transportation route. Stabilisation and widening of slopes by blasting need closure of the route for a considerable time. Discontinuing traffic on Konkan Railway route was undesirable as it connects two important port cities Mumbai and Mangalore. The paper presents an innovative directional controlled blasting (DCB) technique for excavating three unstable slopes (i.e. cuttings) in hilly terrain without disturbing the traffic. New empirical formulae for small geometry blasting to estimate burden and throw have been developed. A unique sequence of firing and excavation with powder factor varying between 0.04 and 0.39 kg/m3 irrespective of the actual free face was used for rock blasting. The process controlled the throw of blasted material over the track and resulted in a smooth and stable wall. The slope angle has been changed from 80 to 82° to 45–47° and probability of wedge, planar and toppling failures was eliminated. About 100 such accident-prone slopes (52 km cumulative length, 7% of total route) situated at discrete locations along Konkan Railway route were stabilised using the technique. No incident of rockfall and slope failures along these slopes has been observed after the stabilisation.

By Dillon. Patricia

Business Growth ?Coal ?Targeting 30 million tonnes by 2013 compared to 19 million tonnes produced in 2009 ?Expanding Energy Business unit (Oil Sands) ?Copper -Strong growth potential for existing operations and development projects ?New gold strategy recently launched ?New markets for zinc Need to retain existing and attract new employees to support growth Engaged Employee ?Has a positive attitude towards the organization and its values ?Is a person who is fully involved in, and enthusiastic about, his or her work Engaged employees are more likely to stay with the organization.

May 1, 2010

By François Charette

High stress conditions in weak rock masses lead to large deformation and breakdown of the rock material, while stress release events in hard rock mines can lead to sudden and usually violent rock failure. Typical support systems combine various reinforcement and support mechanisms to provide the required convergence control and retainment, but results are often mitigated by failure of surface liners, shotcrete and tendons. The paper reviews differing requirements of support and reinforcement for different failure types. In addition, the mechanical performance of a new reinforcing tendon is presented and analysed in view of the field requirements. Field tests results are presented.

May 1, 2011

By Ali Porbaha

In today&apos;s fast-track construction environment, owners are searching for non-conventional technologies to build their projects faster and safer while maintaining traffic flow during construction. To that end designers and contractors are providing solutions that incorporate many unique features to expedite construction processes. In addition to timely delivery of the finished highway products, there is an increasing interest in making the initial investment in applying innovative technologies and thereby minimizing costly maintenance of highway projects. Accordingly, the aim of this paper (along with the accompanying paper) is to examine innovative technologies, developed mostly in Europe, that accelerate construction of highway, runway and railway embankment foundations. For each technology, a basic concept, installation technique(s), and design considerations are discussed, along with the case history of a real-world project. The Geotextile Encased Columns (GEC), AuGeo, and Continuous Flight Auger (CFA) are presented in Part I. Deep Mixing (DM), Mass stabilization, Cut-Mix-Injection (FMI), and Combined soil Stabilization with Vertical columns (CSV) technologies are discussed in Part II.

Jan 1, 2002

By G. S. Takenaka

When Bridger Coal Company transformed their operations from surface mining to an underground longwall operation their plans included not only the addition of new mining equipment but also surface fans for a blowing (supply) air ventilation system. The original system concept included a propane gas fired air heater to preheat the intake air during cold weather and a dual parallel fan and duct system. One fan operated to ventilate the mine while the other fan was for stand-by emergency operation. Equipment proposals were submitted in March, 2005 based on the dual parallel fan system. Discussions conducted during the equipment selection process revealed that several alternative system design concepts were available. The alternative concepts included innovation features that not only saved space and cost but also reduced operating expense as well. Many of the features were incorporated into the final design of the system. A comparison of the original system concept and final installation design are presented in the paper in addition to details of the features and the derived benefits.

Jan 1, 2009