Search Documents

Since the introduction of water cooled test rings the operation of cupelling retort bullion has not alone been sImplified, but has also been the means of concentrating the bullion for the fining test in a much shorter time.The first water cooled test ring which I used was rectangular in shape, inside dimensions 5 ft. 3 in. x 2 ft. IQ in., and made of i in. mild steel plates, with a water space of 9i in. x 3t in. However, it was found that as soon as the filling commenced to wear and the litharge came in contact with the jacket, the plate was gradually affected on the lines of the wash, caused by the blast. After a while the inside steel plate went beyond the factor of safety, and was then substituted on the sides and the front of the test ring by a tin copper plate, which has stood now for the last five years without showing the least signs of wear or leakage.The test remains in use as long as the bottom is regarded as safe, and toward the end of the life of the test the litharge is allowed to work against the copper plate.

Jan 1, 1901

By K Niyomjinda, B Etschmann

Chatree Gold Mine is currently the only modern day gold mine operating in Thailand, and is situated approximately equidistant from Chiang Mai in the north and Bangkok in the south. Environmental guidelines set by the Thai authorities require Chatree Gold Mine to achieve a Total Cyanide level of 20 ppm or less in the process plant discharge slurry stream prior to release into the tailings storage facility. This paper describes both the initial difficulties faced in achieving compliance on this limit utilising the conventional INCO SO2/Air cyanide destruction system and the subsequent process improvements initiated to both the leaching process and the standard INCO process to achieve the current compliance levels of approximately 99/100 shifts. Improvements were focussed on the dual aspects of reducing the formation of WAD cyanide and ferrocyanide species in the leaching circuit coupled with process changes to improve removal of the ferrocyanide species from solution during the cyanide reduction stage.

Jan 1, 2004

By T Hughes

The Gekko InLine Pressure Jig (IPJ) was unleashed on the World gravity separation market in 1996 and has since sold over 150 units in applications including tin, diamonds, silver, coal, garnet and gold. During the past twelve years the knowledgebase of the best applications and capabilities of the IPJ has greatly increased. Improvements to the original IPJ design have included engineered ceramic ragging in specific gravities from 1.6 to 5.0, full automation and improved designs of feed presentation and tailings and concentrate handling systems. The IPJ has been found to be able to handle a wide feed size range and recover mineral at liberation size without significant addition of water to the mass balance. Test work carried out during full-scale operation of the IPJ has shown the IPJ can recover diamonds down to 0.5 mm, sulfides down to 0.3 mm and gold down to 0.1 mm which greatly expands its application in the mineral processing industry. A significant volume of data now supports the symbiotic benefits of an IPJ and flotation circuit combination to pre-concentrate an ore and minimise downstream processing requirements.

Jan 1, 2008

By C Barton, B Randall, T Weldon, M Lefler

FLSmidth-Summit Valley Technologies has been a leader in gold processing equipment for nearly two decades. Over the past several years an extensive research and development effort has led to improvements in Mercury Abatement systems and process efficiency in Adsorption Desorption and Regeneration (ADR) or "Carbon" plant operations. Two technologies will be discussed that are focused on efficiency improvements followed by an explanation of Mercury Abatement systems. Gold and silver can be desorbed from carbon in several ways. FLSmidth has made significant improvements to the Pressure ZADRA process allowing for lower energy consumption and lower capital costs. This patented process is known as the Split-ZADRA Strip method. Split-ZADRA allows a plant to elute loaded carbon in a semi-continuous fashion. This increases the grade of the Pregnant Strip Solution, improves electrowinning efficiency, reduces capital equipment costs, and reduces energy requirements. During desorption and electrowinning for the Pressure ZADRA process, the pressure and temperature of the circulating strip solution is changed multiple times. A self-contained heating and cooling system has been developed which decreases the energy requirements for elution. Mercury Abatement technology has become increasingly important in recent years. Along with FLSmidth Summit Valley Technologies' complete Mercury Retorting Systems, FLS-SVT has developed systems for the capture and removal of mercury from electrowinning cell and strip solution exhaust, Carbon Regeneration exhaust, and the dore furnace exhaust. This paper describes each of the technologies introduced above and their success in operational gold and silver mines. Case studies will be discussed showing the advantages of each specific technology as it applies to operations around the world. CITATION:Lefler, M, Weldon, T, Barton, C and Randall, B, 2013. Improvements in the mercury abatement and process efficiency of adsorption, desorption and regeneration gold processing operations, in Proceedings MetPlant 2013 , pp 468-478 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Yoneji Kanoh, Masahiko Ohtsuka

In Japanese tunneling history, it has commonly been accepted that the long-round driving is difficult due to the complicated geological condition. Therefore, the maximum past record has been less than 3 m per round. A new record of advance was established in the 99 m2 headrace tunnel of Imaichi Water Power Station Project with an advance of 239.5 m in a month by drilling 3.9 m deep blast holes. The geology of the headrace tunnel composed of pyroxine andesite (ie. 960-1770 kg/cm2, VP3.1-4.3 km/s) which had several clay seams and open cracks and was moderately weathered. Automatic shotcrete machine was used for shotcreting. Rock support was specified according to the N.A.T.M. with each different rock type. The contractor achieved a remarkable tunneling advance not earlier experienced in Japan.

Jan 1, 1983

By William R. Yernberg

The Fifth International Conference on acid rock drainage (ICARD 2000) was held May 21-24, 2000, in Denver, CO. The three-day conference consisted of about 150 oral presentations and poster sessions that described the state-of-the-art of acid-rock-drainage (ARD) science and technology. The conference also featured a trade show. It included representatives from consulting companies and government agencies with interests in ARD, as well as other environmental issues related to mining. The conference also included field trips to ARD treatment sites and short courses on acid rock drainage issues. ICARD 2000 was planned and promoted by the ICARD 2000 Organizing Committee and the Society for Mining, Metallurgy, and Exploration, Inc. (SME). Financial support was provided by Barrick Gold, BHP Copper, Homestake Mining, Noranda, Phelps Dodge, PlacerDome, the US Bureau of Land Management, the USEnvironmental Protection Agency and the US Geological Survey. Since the original ICARD was held in Roros, Norway, in 1988, knowledge has improved of the behavior of mine wastes as have methods of environmental mitigation. The ICARD 2000 presented the latest advancements in the field of acid drainage.

Jan 1, 2000

By Beevers J

The Ok Tedi Project is now a high production open-pit porphyry copper mine located in the Star Mountains of Papua New Guinea (PNG). At present, total daily production is 190 000t of ore and waste. Large scale drilling and blasting has only been in operation since 1988, prior to which all material was removed by ripping and dozing. This paper reviews the steps taken over the last 12 months in establishing a more efficient drilling and blasting operation and highlights the significant reduction in powder factor. These improvements have been achieved largely through the introduction of air-bags, controlled pattern expansion and an overall focusing on the operation by involving consultants, ICI's technical service and internal departments.

Jan 1, 1991

By Greg M. Hollyer

The search for minerals in the future will be dominated by deeper exploration and the need to accurately target ?blind? deposits as more and more of the ?easy? near surface targets are exhausted. In this context, key technologies are emerging for deep exploration both in grassroots and minesite exploration, including the Titan 24 Deep Penetrating geophysical technology. Introduced in 2001, this technology has grown rapidly into an accepted approach for exploration in a variety of geologic environments, including brownfield environments where discovering additional reserves would most quickly benefit companies. Titan 24 belongs to a new class of sophisticated Distributed Acquisition Systems (DAS) which record high-volume, high-quality data simultaneously at multiple receiver stations. This data is then processed digitally, modeled using specialized inverse modeling software, and interpreted according to geologic and other parameters. The result is a robust, high-quality, high-volume data sets which provide a basis for improved imaging to depth. In this paper, the Titan 24 distributed technology is discussed. Illustrations of the vast improvement to overall exploration are showcased through results in several case studies. These include examples from two gold deposits, a porphyry deposit and a minesite. These examples show the range of applicability of the technology and the ability to effectively image mineralization, lithology, structure and alteration to depth as an aid to understanding prospective mineral deposits and targeting drills more accurately.

May 1, 2008

By A D. Campbell, G R. Power

Many caving mines use numerical flow models to simulate mine production, forecast recovered ore grades and optimise the draw strategy. In sublevel caving (SLC) mines, the effects of blasting and fragmentation at an individual ring scale generally cannot be included in these models. Previous attempts to use results from marker recovery trials to calibrate numerical flow models have been limited due to difficulties in accounting for blasting effects at a ring scale. This paper outlines how an empirical criterion for blasting and fragmentation was used to attribute variable flow properties into a numerical flow model based on the blast design and modelled fragmentation. The flow model was then validated using data from a number of full scale marker recovery experiments. The result of this approach was a significant improvement in forecast accuracy when compared against the same modelled cave marker recovery without the inclusion of these blasting effects. Improvements in the flow model are currently being adopted within the mine scale model to further improve the accuracy of grade forecasting, optimise the draw strategy and increase net present value. The integrated modelling approach is also being used to simulate the effects of different drill and blast designs on cave recovery. It is suggested that, if implemented, the technique would lead to improved blast designs in other SLC mines, increase the value of marker trial data and reduce costs associated with large scale blast design trials.CITATION:Campbell, A D and Power, G R, 2017. Improving calibration of flow models against SLC marker trials by linking blasting effects to particle mobility, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 11–22 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By M. Shapiro, L. A. le Grange, B. Henning

A paper was presented by Bateman Minerals and Metals at INFACONX (2004) describing a simplified Computational Fluid Dynamics (CFD) Model for predicting the temperature and velocity distributions in all the fluid zones of a single electrode DC Furnace simultaneously with the temperature distributions in the refractory lining of the vessel. The boundary conditions imposed on the model consisted of the arc current, external surface film coefficients and ambient temperatures. The temperature and velocity distributions in the free-board, slag and metal were solved simultaneously by coupling across the interfaces between the fluids and transportation phenomena developing in the plasma arc. A simplified model was used to describe the ex-change of energy by radiation between the arc and surfaces enclosing the freeboard region. The strengths of this model were reported as being the ability to: ?Solve the different zones and transportation phenomena simultaneously without the need to transfer partial numerical results between different numerical analysis applications. ?Solve velocity and temperature distributions without assumptions regarding internal film coefficients and additional internal temperature boundary conditions. One of the disadvantages of the model was that the energy absorbed by the process was not modelled, resulting in vessel performance predictions under heat loss conditions only. Whilst this allowed potential problem areas such as localized refractory heating to be identified, the model was only capable of predicting how these could be improved by varying the overall geometry and materials of construction. This paper presents improvements in the application software and user defined subroutines of the model as follows: ?Incorporation of surface to gas, gas to gas and gas to surface radiation models to improve the accuracy of radiative heat transfer mechanisms within the freeboard. ?Incorporation of a process energy absorption model based on a theoretical temperature dependant enthalpy curve which incorporates melting, smelting and superheating in selected areas of the bath. This enables the effect of feed distribution and power to feed ratio changes to be estimated. The effects of a commercial arc at full power on the freeboard and slag can now be simulated with increased accuracy.

Jan 1, 2007

By H. Do, R. Yoon

Mineral flotation is effective over a relatively narrow particle size range of approximately 10 to 100 µm. If the upper particle size limit can be increased, however, a run-of-mine ore may be coarse ground, and only the middlings are ground further to achieve required grades. This will result in significant energy savings and increased throughput. In this communication, methods of increasing the upper particle size limit will be discussed on the basis of a flotation model that can predict flotation from both hydrodynamic and surface chemical parameters. An example of increasing flotation recovery by control of a chemistry parameter is given.

Jan 1, 2007

By Jose R. Hernandez-Aguilar, Jeet Basi

"The study evaluated the impact on overall circuit metallurgy of improving the performance of the two flotation columns that make up the final Mo cleaning stage in the Cu/Mo separation circuit at Highland Valley Copper mine. The results showed that a key factor to improve the overall circuit metallurgy was to control the size of the bubbles generated in the columns. When a large proportion of small (< 1 mm) bubbles were generated, the production rate of solids-in-concentrate increased by a factor of 4-5 compared to typical production figures without compromising concentrate quality. This increase in concentrate production rate reduced the circulating load in the circuit causing a significant increase of Mo recovery. A statistical analysis of historical production data showed a strong relationship between final concentrate production rate and overall Mo recovery. This relationship along with the results from this study indicated an opportunity to increase the recovery of Mo from 90% (typical) to 94% without downgrading concentrate grade. This 4% increase represents about 14,000 lbs or $500,000 worth of Mo each month at current metal prices.To provide a rational interpretation of the results, this study also examined whether the model of Gorain et al. (1997; 1998; 1999) could explain the increase of Mo recovery seemingly resulting from the decrease of bubble size. The data showed that the model predictions did not agree with the experimental data, i.e., for a given change (decrease) of bubble size, the predictions underestimated significantly the observed recovery increase. An interpretation based on the fundamental analysis of Finch and Dobby (1990) and Hernandez-Aguilar et al. (2005) is proposed to explain the discrepancy between measurements and predictions obtained from Gorain et al.’s model.INTRODUCTIONIt is generally accepted that the size of the bubbles generated in a flotation cell – a concept usually referred to as “bubble size” – has a significant effect on metallurgical performance. However, a significant number of mineral processing practitioners often question, with valid reasons, the practical benefits of implementing process improvement strategies based on controlling bubble size. “Small” bubbles are often considered to be “favourable”, but how small they need to be for a particular case, or how to adjust operating conditions to control a target bubble size, or whether the bubbles need to be smaller in the first place are questions that usually remain unanswered. Two reasons explain this situation."

Jan 1, 2009

By J. Basi, J. A. Finch

ABSTRACT Testing the effects of bubble size (Db) in a Mo cleaning ?otation column at Highland Valley Copper mine indicated that increasing the proportion of small (< 1 mm) bubbles signi?cantly improved column metallurgical response, compared to typical operation. The results were a three- to four-fold Mo recovery increase and a 1 to 2% Mo (absolute) concentrate grade increase. The improvedcolumn operation produced a 4% Mo plant recovery increase. This study also showed that modelling the ?otation rate constant (k) as an inverse square function of Db was more accurate than considering k to be inversely proportional to Db.

Jan 1, 2010

By T. Strong

"Selectively recovering pentlandite from high levels of pyrrhotite presents a technical and operational challenge. The liberation characteristics and also the chemical environment is critical to performing a successful separation. Reviewing the mineralogy to understand the characteristics of the ore and the plant flotation behavior is fundamental to designing a successful improvement program.At Savannah Nickel the challenges presented by a falling nickel price required a rethink of the flowsheet to improve the project economics through improving the concentrate grade and recoveries. Glencore Technology reviewed the plant performance and proposed and tested solutions to improve the grade performance of the concentrator with the support of the plant team. A pilot plant comprising a M20 IsamillTM followed by an L500/1 Jameson Cell was operated on various plant streams. In addition to the pilot plant, flotation surveys and a plant based laboratory program was used to supplement the plant understanding and within two weeks significant improvements were identified and demonstrated. The combination of the pilot operation and the plant based laboratory program was able to quickly demonstrate the improvements and test with equipment that is fully scaleable from pilot plant to full scale.IntroductionPanoramic Resources Limited is a Western Australian mining company formed in 2001 for the purpose of developing the Savannah Nickel Project in the East Kimberley region of Western Australia. Panoramic successfully commissioned the $65 million Savannah Project in late 2004. The process plant at Savannah comprises a single stage crusher, SAG mill, flotation, thickening and filtering stages to produce a bulk nickel, copper, cobalt concentrate. Metallurgical recoveries average 86-89% for nickel, 94-97% for copper and 89-92% for cobalt. The plant was originally designed for a throughput of 750,000 tonnes per annum, but has consistently outperformed the design specifications.Due to low nickel prices the Savannah Nickel mine and processing plant were placed into care and maintenance in May 2016. Prior to suspending production Glencore Technology was engaged to investigate options to improve the concentrate grade. With the discovery of Savannah North in 2014 and the Savannah North Scoping Study demonstrating LoM ~8 years and Mining Inventory of 6.07Mt @ 1.26% Ni, 0.64% Cu and 0.09% Co significant future potential exists. By completing pilot plant studies prior to shutting down, the plant engineering studies can be completed and the plant readied for restart by the time the nickel price improves."

Jan 1, 2017

By H. Golzarpoor

Life Cycle Analysis (LCA) is a methodology for evaluating the environmental impacts associated with a product during its life cycle. LCA is identified as the most reliable method for verifying environmental impacts; however, current LCA-based approaches have certain limitations for environmental analysis of construction products. Integration of the LCA methodology with Discrete Event Simulation (DES) provides a sound framework for modeling and analysing the environmental impacts of construction products. LCA and DES is one possible combination for analysing the cause and effect of various scenarios where time, resources, and randomness of input variables affect the outcome and, therefore, has the potential to address the shortcomings of LCA in construction. Recent studies in disciplines other than construction such as manufacturing systems have revealed positive effects on evaluation of environmental metrics while integrating LCA with DES; however, this integration has not yet been applied for environmental analysis of construction products. By implementing LCA data in a DES model, this research proposes an environmental model of earthmoving operations in a case study. Environmental variables are simultaneously assessed with production variables in the same simulation model and the integration of DES and LCA is discussed.

Aug 1, 2013

By T Hirsi, M Weatherseed, T Ritasalo

Cooling tower design has not advanced significantly in the last decade. Recognising this, Outotec has developed an innovative horizontal outflow cooling tower with increased performance compared to conventional design cooling towers.Outotec&#174; Cooling Towers operate today in applications such as spent electrolyte cooling in zinc plants and for gypsum removal before copper solvent extraction. In such applications the use of this latest design has enabled increased production and lower maintenance costs in the downstream operations.In actual operations, the cooling performance has been confirmed at start-up, and has demonstrated that the towers operate in accordance with the CFD modelling. In the last three years these towers have proven themselves in commercial operation to operate with high efficiency and availability.This case study will outline comparative data, collected over two years at a site where both Outotec and conventional cooling towers are operating. The data shows that Outotec cooling towers require less than half the maintenance time of conventional cooling towers, when adjusted to a total solution flow basis. A close partnership approach with the site has allowed continual development, ensuring high availability and high performance.Experience with previous cooling tower installations guided the development of maintenance philosophies and procedures; this resulted in a design where maintenance intensive components were accessible from the top of the cooling tower. This allows safe access to components and maintenance with little or no downtime.CITATION:Hirsi, T, Ritasalo, T and Weatherseed, M, 2015. Improving cooling tower performance with innovative horizontal outflow design, in Proceedings MetPlant 2015, pp 396–402 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Dwayne C. Kicker

This paper introduces the concept of design theory and methodology as applied to rock mechanics for more innovative and efficient design. This is a "frontier" research area in rock mechanics because although design is a fundamental foundation to all engineering branches, very little attention has been paid to this aspect in mining. In discussing the theoretical premise of design, this paper identifies the principles which form the basis of design activity. Also, from a practical viewpoint, the findings from a series of interviews with mine design engineers are presented. These findings lead to the identification of needs arising from overlooked design methodology in practice.

Jan 1, 1989

By Judy K. Todd

Double benching has been utilized as an excavation technique in open pit mines for many years. This process involves drilling, blasting, and excavating the material for the design bench height. A second bench is then excavated without the creation of a catch bench, i.e. only minimal offset from the first bench face is allowed when drilling off the second bench. The result is a double high bench face or double bench. When drilling off the second bench, the offset of the drill from the bench face projects the lower bench face into the pit up to an extra five meters. This reduces the maximum attainable bench angle, enhances the probability of rock escaping the catch bench and increases the overall strip ratio. The generally utilized process of trim blasting also can impact on the final bench profile by contributing to blast damage of the face. BHP Billiton Diamonds Inc., Ekati Mine Diamond MineTM, has pioneered the usage of a technique that eliminates this offset. Double benching is accomplished by drilling a single, 30m pre-shear (two 15m benches) to define and protect the final bench profile. This article provides a comparison of the attained face angles obtained in the field utilizing both of the above methods, as well as a comparison with the analytically predicted angles prior to excavation.

May 1, 2002

By H. Walqui

The Empire concentrator was built in four stages, with the latest stage accounting for 50% of the overall plant capacity. Over the past 5 years, the average throughput of the three grinding lines has decreased by 50 LTPH (15%) without significant changes in ore characteristics and despite the addition of secondary grinding capacity to supplement the existing pebble mills that are the constraint of the grinding circuit. This paper discusses the different areas under study that are aimed at optimizing grinding circuit utilization which includes improving system logic, pebble crushing operation and pebble mills operation.

Jan 1, 2009

By Mark Osborne, Ray D. Peterson, C. Edward Eckert

"The theoretical melting energy requirement for a typical hypoeutectic aluminum-silicon alloy is approximately 520 BTU/lb. It has been demonstrated, however, that even a state of the art secondary processing-automated lost foam casting operation can exceed this value by at least an order of magnitude when the actual thermal energy input from melting to solidification is monitored. Metal transfer and holding operations constitutes over 65% of this expenditure. The authors present relative benchmark energy expenditure information by unit operation for an offsite melting/lost foam casting line with a daily throughput in excess of 100,000 lbs. Efficiency improvements through optimization of the current process, and anticipated energy values at the culmination of a U.S. Department of Energy sponsored project to develop, integrate and demonstrate an advanced melting, transportation, and dispensation system will be cited.IntroductionThe size of the U.S. aluminum remelt pool was approximated to be 14.21 billion kg (31.27 billion pounds) by a recent study?, with the engineered castings (foundry) sector accounting for 3.25 billion kg (7.16 billion pounds) or 23% of that total. This study considered overall process yield and all major contributors to scrap. The values cited, therefore, are more meaningful than simply tabulating annual pounds shipped by sector.The foundry sector consists of Sand Castings, PM Castings and Die Castings categories appearing in Figure 1. All other categories comprise the wrought alloy sector. Wrought alloy production enjoys an energetic benefit from both scale and a relatively continuous operation. Many foundry operations, however, operate in batch mode at less than design metal throughput with characteristically longer melt holding periods. Since any detention of molten metal beyond melting represents an overhead use of energy, melt holding (secondary) energy expenditures can appreciably inflate melting energy requirements in the foundry."

Jan 1, 2009