Search Documents

By J. E. Murphy, L. A. Walters, F. H. Nehl, G. B. Atkinson

The US Bureau of Mines investigated the selective electrowinning of Ag and Au from cyanide solutions contaminated with Cu with the goal of decreasing the amount of Cu codeposited. Decreasing Cu codeposited will reduce refinery costs. Direct current was applied to the cell in pulsed and square wave voltages at 0.7 A h/150 mL of solution. Times tested for each cycle ranged from 1 to 10,000 msecs. Graphite, lead and stainless steel were evaluated as electrode materials. Square wave electrowinning at 70°C (158° F) gave the best separation of Ag and Au from Cu. Applying 2.5 V during the duty cycle, 0.0 V the rest of the period, a duty cycle of 10% to 30%, and a period of 100 msecs to 1000 msecs gave the following results: Ag concentrations decreased from 34 µg/mL to 0.1 µg/mL. Au concentrations decreased from 54 µg/mL to 0.2 µg/mL and Cu concentrations remained almost constant at 560 µg/mL.

Jan 1, 1995

A description is given of preliminary work done to identify the problems inherent in electrochemical oxidation of metal sulphides, and particularly in the use of powder compacts as anodes in electrolysis. Lead flotation concentrate pressed into a compact can serve as an anode for direct electrowinning of lead according to the reaction PbS -7 Pb2+ +So +2e. No pYrometallurgical step is required, and sulphur is recovered in elemental form.In the experimental work, electrical conductivity of the compacts was achieved by addition of 5·5 per cent of graphite. After compaction at 10-20 tons/sq. in. the anodes were strong and remained intact throughout the electro-oxidation period. Perchlorate electrolyte was used, but fluosilicate electrolyte is also applicable. A sheet of pure lead formed the starting cathode.As anode potential increased above 1·0 V (v. SHE) PbS04 was formed in increasing amount. At 0·90 V, Pb2+ extraction efficiency was 85 per cent. Anode potential was kept low by electrolysing at 60°C and 15 mA/sq. cm., and by improving the porosity of the compact. Other metal sulphides (Zn, Fe, Cu) in the flotation concentrate also oxidize and release metal ions to the electrolyte, which would need to be purified prior to deposition of lead.Power requirement in a laboratory cell was about 0·24 kWh per lb of lead extracted.

Jan 1, 1972

By G A. Challis, A B. Christiel

Microprobe analyses of electrum grains in some Hauraki Au-Ag deposits indicate that gold fineness is in the range of 500 - 800 (50 - 80 per cent Au), but for most deposits the range is usually narrower than this. The electrums contain minor amounts (<0.8 per cent) of copper, arsenic, antimony, mercury, iron, and sulphur. Platinum and palladium were analysed for but were not detected (detection limit 0.24 per cent for Pt or Pd). For some deposits (eg Waihi), the average fineness values for the analysed electrums correspond fairly well with the electrum fineness determined by assay during the historic mining operations.

Jan 1, 1992

By Fardy J. J

Abundance data are presented for a comprehensive range of elements in oil shale samples from deposits located in Queensland. The techniques of instrumental neutron activation analysis and spark source mass spectrometry were used to obtain concentration data for up to 50 trace elements in each shale. These techniques were supplemented by other spectrometric methods to obtain data for major, minor and some trace elements. Sixty-four elements were determined quantitatively. This comprehensive characterisation of oil shale samples from the major deposits in Australia provides inorganic abundance data not previously available. It also provides important background information for processing studies and the associated environmental aspects of shale oil production and waste disposal.

Jan 1, 1986

By D. van Heerden

In the mining industry abrasion caused by both sliding and impact have over the years resulted in costly damage to installations such as ore passes and silos. Good geotechnical practices combined with the use of a high quality abrasion resistant concrete can prolong the life of such an installation and minimize problems associated with abrasion. In order to maximize the life of an abrasion resistant concrete, the choice and combination of the correct raw materials (cement, aggregate and fibre) and overall mix design needed to make up such a concrete are important. This paper presents technical data and practical experience showing that concrete formulated with calcium aluminate cement resists severe abrasion conditions better than similar OPC-based concretes.

Jan 1, 2005

By W. A. Wilkinson

In creating a surface mine design, a complicated series of events may be required to meet both mining and environmental objectives. Envisioning the mine at every step of the operation can greatly assist the engineer to identify design and operational problems that might otherwise go undetected until the field operations reach the problem. Providing operations a visual progression of the mine ensures that critical designs generated by the engineer are understood and effectively communicated to operations. Providing the plan as electronic data to the surveyors and/or on-board GPS systems can ensure successful implementation of the design. This paper discusses using computer technology to generate a virtual mine plan and strategies to consider when communicating a virtual mine plan through electronic and paper formats.

Jan 1, 2002

By D Craw, K A. Hunter

Deposits of the metalloids arsenic and antimony occur in quartz veins of mesothermal hydrothermalsystems in the South Island as arsenopyrite (AsFeS) and stibnite (Sb2S3). Arsenopyrite and stibnite occur in natural exposures in gold-mining areas, and additional arsenopyrite and stibnite have been exposed to the atmosphere by mining activity. At present the drinking water limits for dissolved As and Sb are 10 ppb and 3 ppb respectively. Sampling and analysis techniques are critical to determination of metalloid concentrations at these low levels. Endeavour Inlet in the Marlborough Sounds is an historic mining area (late 19th Century) with elevated As and Sb in waters emanating from mineralised rocks. Waters running out of abandoned adits have concentrations of As and/or Sb up to ppm levels. Natural waters have high Sb and low As, and the As levels increase markedly where anthropogenic activity has exposed rock. Changes in Sb/As ratio could potentially be used to quantify the anthropogenic component of metalloid mobility on mine sites on the 100-year time scale.

Jan 1, 2002

By Luis Adrianzen Lamadrid

La eliminación de la dosificación de cal de un proceso de flotación es difícilmente lograda, si bien algunas empresas han logrado implementar reactivos que ayudan a depender menos de esta, otras empresas en cambio; han logrado no depender de este modificador de pH; pero con resultados poco sostenibles y solo en uno de sus circuitos.

Sep 1, 2017

By Henry Schwellenbach

LABOR shortages, rising wages, and changes in moisture and fines content of the ore necessitated a review of the flowsheet at Warren Foundry & Pipe Co's. Mt. Hope, N. J. Mines Div. This plant had been designed prior to World War II, and started operations in January 1945. When this operation was designed there was an oversupply of labor in the area, wages were at a reasonable level, the run-of-mine ore was low in moisture, and there was a limited amount of fines. These factors all favored use of hand picking for cleaning rougher lump concentrate. Since that time, many changes have occurred. The proximity of defense industries and large military installations, has created one of the most acute labor shortages in the country. This labor shortage together with present wage levels, and the increase in moisture and fines in the ore created several problems. The increase in moisture and fines may be attributed to changed mining methods, the extensive use of sprays, and the opening of new mining areas bringing an increase in ground water. [ ] Two problems were presented by the increase in moisture and fines. The first was that lump ore arrived at the open hearth in an unacceptable condition, due to the segregation enroute of the large amount of fines that had adhered to the lumps. The second problem was that high magnetite content fines coated the large lumps, making it difficult for pickers to distinguish middling by other than the relative weight. [ ]

Jan 1, 1952

By N. Raeis Hosseiny, S. H. Bassir

"Chador-Malu iron ore is one of the most important iron mines of Iran.About 98 percent of Fe in the ore is in shape of Magnetite, Hematite, Martite, aqua oxide of Iron and the other irons are with ferrous silicates, actinolite, cholorite and ferrous dolomites. 1% of Fe has replaced in pyrite. The phosphor distribution in the ore is non-hemogenous and its average in the whole of the deposit is 94%. It is in shape of Apatite.This mine contains considerable phosphor, which makes it useless for metallurgical uses. At this mine the phosphor is reduced in the iron ore at two steps. At the first step, magnetic part of the ore is separated from the gangues and phosphors by magnetic separator. At the second step, the ore is enriched by the flotation methods. Experimental flotation methods to obtain the optimum conditions are as follows:• Effect of Starch as Hematite depressant with ATRAC as Apatite collector• Effect of Sodium silicate as Hematite depressant with ATRAC as Apatite collector• Effect of ASAM as Apatite collector with Sodium silicate as Hematite depressant• Effect of ATRAC (BEROL) as Apatite collector with Sodium silicate as Hematite depressant• Effect of ASAM & ATRAC mixture as Apatite collector with Sodium silicate as Hematite depressant• Effect of Kcarbonate as pH-modifier• Final test to Optimize pH, Collector, DepressantAt this research we have found the optimum circumstance of the flotation of Chador-Malu iron ore in order to decreasing phosphors of iron oxide and floating of Apatite to make pure Hematite.To reach the optimum conditions, some tests were done with different amounts of pH, collector and depressant. The results are as follows:"

Jan 1, 2003

By Ram Avtar

High tensile thick plates (>80mm, weight ~3000 Kg) of medium carbon low alloy steel, when heat treated, manifested higher percentage of crystalline area (>20%) in fractured surface. Such problem was not encountered in thinner plates. The genesis of higher crystallinity in fracture was examined. It was observed that the thicker plate undergone slower rate (Average 0.9oC/Sec.) from soaking temperature to Ms temperature) of cooling after austenising during oil quenching and thereby quenched microstructure had upper bainites. During tempering of as quenched bainite, additional precipitation took place at the lath boundaries of bainite. This led to weakening of grain boundaries and aided easy crack propagation during fracture and resulted in formation of higher percentage of crystalline area in fractured surface. Enhancement in cooling rate (Average 1.8oC/Sec. from soaking temperature to Ms temperature) of austenised plate by switching over from oil quenching to water quenching practice resulted in complete transformation of austenite into martensite and produced ductile fracture (zero Crystallinity). Plates conformed improvement in mechanical properties between 2-5%.

Jan 1, 2009

By Basem Sh. Hazzan

In the last four decades significant effort has been devoted to designing piles in expansive clay soils. Nevertheless, only a scant effort has been devoted to the elimination of heave forces acting on the upper part of lightly loaded piles. For this purpose, an investigation site was established in Karmiel in Northern Israel. On this site sixteen unloaded cast-in-situ piles, both uncoated and coated, were installed in a moderately expansive clay soil in the end of summer 1996. The piles were executed to different depths ranging between 2m and 7m and were observed over a period of 27 months. Another nine unloaded cast-in-situ bored piles were installed at the end of summer 1998 for carrying out pullout tests. These piles were embedded two meters from the ground surface. Results obtained from observations and from full-scale static pull out tests showed that separating the piles from the surrounding clay in the active zone by a twin walled sleeve eliminated the heave forces significantly. The scope of the work is, determining of the elimination degree of the heave forces due to the provision of the above sleeve.

Jan 1, 1999

By Hiroyuki Sano, Chikabumi Yamauchi, Mitsuru Tanahashi, Toshiharu Fujisawa, Shin-ya Iwahori

"Pyrometallurgical process using Cu2O-based slag was proposed as a recycling process for copper scrap. However, it is difficult to remove nickel from copper by oxidative refining. Therefore, it is necessary to reduce the concentration of nickel in copper before the oxidative refining. In the present work, the copper enrichment stage in this recycling process, where copper scrap melt is separated into the Fe-C-Cu melt and the molten copper, was taken up and the compositions of both melts were measured. Based on the above results, the distribution ratios of nickel between the Fe-C-Cu melt and the molten copper were calculated. Furthermore, the optimum condition of copper enrichment stage was discussed from the viewpoint of nickel removal and copper recovery. The possibility of recovering 4N-purity copper by using this recycling process was confirmed.IntroductionRecycling is well known as a method for saving resources and reducing environmental damage. More than 99% of copper is used in metallic form - as metal or copper alloys[l]. High-grade copper scrap is directly re-melted and reused, while low-grade copper scrap is transported to copper smelters to be pyrorefined and electrorefined. Nevertheless, a great amount of copper is being stockpiled in the cities and should be recycled in the near future. At that time, the current recycling process will face new problems due to the increases in the recycling rate to the smelters. This includes insufficient combustion heat to melt copper scrap and ·almost no benefit in electrorefining because the scrap does not contain gold and silver. Thus, an alternative pyrometallurgical method for copper scrap refining will be required."

Jan 1, 2000

"Placer Dome Inc.'s Dome Mine is located in South Porcupine, Ontario and has been in production since 1910. In the past, the mill leach circuit was preceded by preaeration and primary filtration circuits. These circuits were operated to overcome the effects of pyrrhotite in the ore which reacts with cyanide to form cyanates and thiocyanates and also consumes oxygen.In early 1989, primary filters were by-passed for an extended period. Actual plant results showed no affect on gold recovery or cyanide consumption so the circuit was left off-line permanently with significant cost savings.In 1990 it was determined that considerable savings could be realized underground if backfill storage facilities were located in the mill. It was decided to convert the preaeration pachucas to backfill storage tanks on a trial basis. The trial proved successful with no effect on recovery or significant increase in reagent consumption occurring due to the elimination of the preaeration circuit. The converted pachucas worked well as backfill storage tanks.Modifications such as these have helped to keep the Dome's millings costs among the lowest of Canadian gold producers."

Jan 1, 1992

By Alan Jorgansen, Dave Hummer, Scott Scovira

Kennecott Energy's Colowyo Coal Mine is the largest open pit coal mine in Colorado and produces 5.5 MM tons per year. Colowyo uses the terrace mining method to recover up to seven seams of rolling coal ranging in thickness from 5 to 20 feet. Draglines are used to strip overburden ranging from 60 to 120 feet thick off two coal seams. These two seams are characterized by soft and fold fractured coal and in past practice cast blasting caused excessive coal damage. As a result, to ensure minimal coal damage and high coal recoveries, the overburden was excavated in two passes. The first pass removed the upper overburden to within 10 to 20 feet of the coal seam. The second pass removed the remaining overburden above the coal. Two-pass mining was effective in controlling coal damage, but also carried significant additional costs.

Jan 1, 2003

By Brendan Reilly, Jon Isaacson, Paul McDermott

Kenny/Shea JV is constructing the water intake tunnel for the new Elm Road Generating Station, a supercritical coal-fired power plant in Oak Creek, Wisconsin, being built by Bechtel Power Corporation. The intake tunnel system consists of a temporary mining shaft, pump house and intake channel riser shafts, and four lakebed intake shafts. An 8.33 m diameter, 2,800 m long TBM mined rock tunnel is being constructed to connect the shafts. The intakes are located 2.4 kilometers offshore in Lake Michigan. The shafts and tunnel are being constructed in glacial tills and Silurian Dolomite. The estimated tunnel completion is December 2007.

Jan 1, 2007

By M. Jeffrey

This study investigated the elution of precious and toxic metals from activated carbon. Gold and mercury are of primary interest, due to their value and environmental impact respectively. A laboratory elution rig was commissioned to simulate industrial Zadra and AARL carbon elution conditions. Mercury was found to elute most effectively in strong caustic cyanide solutions; gold was found to elute most effectively in hot low ionic strength solutions. As cyanide decomposes on contact with activated carbon at high temperatures, optimum elution conditions for gold conflicts with those for mercury?no practical compromise in conditions was found. However, sequential elution allowed reasonable recovery of both metals. Ongoing work is looking at the deportment of other metals under elution conditions.

Jan 1, 2009

By I. D. Schleicher, L. H. Rorden, F. B. Curry, T. C. Moore

The purpose of this program is to extend electromagnetic (EM) techniques for use in locating miners trapped in mines as deep as 1000 m. A previously developed EM system is considered adequate for use at mines less than 300 m deep where it has a probability of detection of 54%. A system for deep mines must keep underground equipment simple, and use extremely low frequencies (ELF), sensitive receivers, and noise cancellation. The proposed location method, developed by Develco for other applications, is based on vector field measurements from two or more static sensors and computation of source location by iterative techniques. During Phase II, very sensitive search coil sensors were built and used in a separate test to verify the feasibility of atmospheric noise cancellation. A "Breadboard" location system version without cancellation, which is a fieldable test bed to evaluate receiving and location functions, was tested and supplied. Very good results were achieved from the first in-mine test with the transmitter at a depth of 380 m. It is expected the results of this work, and additional evaluation tests in the future, will be used to define the requirements for a prototype operational system.

By B. B. Broms

Embankment piles are common in the Scandinavian countries (Kjellman, 1940) and in Southeast Asia as support of fills, light structures, bridge abutments and deep excavations (Eide, 1968) as described in the following. Untreated timber piles are often used for light structures and shallow fills when the ground water level is high since they are inexpensive and readily available. When the applied loads are relatively high precast concrete piles and steel piles are preferred. DESIGN CONSIDERATIONS Embankment piles carry the load from a fill or a struc-ture either through skin friction along the sides of the piles (Fig. 1a) or through a precast concrete slab or through pile caps at the top of the piles (Fig. 1b). When the load is carried by skin friction it is often economical to use small diameter timber piles because of the large surface area (Asplund, 1939). For precast concrete or steel piles concrete caps are used to transfer the load to the piles due to the relatively high capacity of the piles since the skin friction resistance alone is not sufficient to transfer the load to the piles.

Jan 1, 2010

By Louise Pearce

?Environmental and social impact assessments (ESIAs) are: ??process-driven and scientific processes ??The process entails a number of steps and procedures which result in obtaining a licenceto operate ?and moving more towards a social license to cooperate. ?However, the primary premise of ESIA is to facilitate the consideration of environment and the communities in planning and decision-making which would ultimately make it possible to arrive at decisions that are ?sustainable?. ?Hence, ensuring the development of the mining sector on a sustainable basis is a critical challenge that needs to be addressed by the global community.

May 1, 2011