Search Documents

By Timothy W. Beck

Roof bolter occupations in underground coal mines continue to experience overexposure to respirable dust. One potential source of dust in roof bolting operations is the exhaust from the roof bolter dust collection system. A wet exhaust conditioner (?water box?) has been developed to reduce dust emissions from the exhaust of the vacuum dust collection system on roof bolting machines. The exhaust conditioner consists of a muffler chamber and a water chamber with four internal partitions to direct airflow over the surface of the water. The National Institute for Occupational Safety and Health conducted a series of laboratory tests to assess the respirable dust capture ability of this device as compared to the standard exhaust muffler. To determine the dust collection efficiency, both devices were placed in the exhaust stream of a simulated roof bolter dust collection system. Gravimetric samplers were operated upstream and downstream of the exhaust conditioner and muffler to evaluate the ability to capture both respirable coal and limestone dust. Researchers observed a 41 percent reduction in dust concentrations for the water exhaust conditioner in the laboratory configuration. Significant levels of dust deposition in the sampling chambers may have contributed to this effective capture rate.

Jan 1, 2010

By D. Ingram

"PRIMARY DUST COLLECTOR A. 42,000 CFM James Howden Fan Z-6 Size 3650 Fan Dia 40"" HP 75It was found that the fan was not large enough to remove the air that was displaced by the trucks dumping. So it was removed and an enclosure was installed to isolate the gyro from the rest of the building.B. FANSJames Howden Fans Model RPM 3500 Series 357 FW HP 10These fans were installed when the first dust system was put into operation. It was found that the high RPM and extreme fan wear caused a major maintenance problem. These fans were replaced with Chicage Blowers Model SWS1 RPM 1180 Dia 36"".DRY CYCLONE COLLECTORS A.,Three four foot rubber lined cyclones. Four six foot rubber lined cyclones.All under flow. Water is controlled manually and gravity flows to a central sump box. From there it flows to the grinding circuit in the Mill.Cyclone under flow product runs between 100 and 200 tons of dust per 24 hours with a screen analysis 30% + 400.The cyclone under flow product is diluted to about 3 to 4%. Solids total gallonage approximately 400.B.,Elbair Wet Scrubber125 HP RPM 56042,000 CFM,Model PX861The Elbair collects the total product from the discharge. Of the Cyclone fans the under flaw goes to the Mill - the Elbair discharges stack goes to atmosphere.The Elbair wet scrubber had to be redesigned in order to keep it in service."

Jan 1, 1976

By L. W. Hamel

"DUST CONTROL - GRANISLE COPPER LIMITEDINTRODUCTIONGranisle. Copper Limited is located in the north-central region of the Province of British Columbia, approximately 200 road miles north-west of Prince George. Mill startup was in November, 1966, at a rate of 5,000 tons per day, expanded to 13,000 in 1973. The primary crushing rate is 1,200 tons per operating hour, and the secondary 750, and they can be operated jointly or separately.DUST COLLECTION SYSTEMS There are seven dust collection systems ventilating the crushing and grinding complex. The individual pickup points are depicted on Figure 1 -""Crushing Plant Flowsheet"", and Figure 2 - ""Concentrator Flowsheet"", e.g. 1A, 1B, 3C, etc.System No. 1 - Primary Crusher The feed rock box of the Allis-Chalmers superior 42-65 primary crusher is ventilated by 19,000 CFM of air exhausted directly to atmosphere by a Sturtevant 426 M fixed discharge fan.No. Dust Pick Up Point CFM lA Crusher Feed Rock Box 19,000System No. 2 - Primary Crushing and Screening System No. 2 ventilates the primary crushing and screening equipment. A total of 19,000 CFM of air is exhausted by a Sturtevant 426 M fixed discharge fan through a Howden Type S - size 75 cyclone locally modified for wet scrubbing."

Jan 1, 1976

By P. S. Capper

"Generally speaking, the most intensive efforts at dust control in the mining industry have, in the past, been concerned with underground operations and where uranium ore or high silica material is processed. In the past several years, Stoop Rock has made Intensive efforts to reduce dust levels in it's Iron ore pelletizing complex. There have been no great engineering break-throughs with regard to dust control in such plants, and certainly no new engineering techniques have had to be applied at Steep Rock. This paper deals with how significant improvements in dust levels have been achieved through minor modification to dust collectors and ventilation units, improvements in operating practices, and education of supervisors and hourly personnel.PROCESS DESCRIPTIONSteep Rock Iron Mines is located 120 miles west of Thunder Bay near Atikokan. (fig. 1) Run-of-mine ore is pelletized along with some -1"" concentrate that has been processed in the concentrator (a summer operation only), which utilizes gravity separation to upgrade a mechanical mixture of ore and waste."

Jan 1, 1976

By F. J. MacPherson, A. C. Caron

"Cassiar Asbestos Corporation Limited is at present B,C.'s only asbestos mining company, and has been actively engaged in the management and operation of the Cassiar Mine since the early 1950's. The Cassiar operations are located between 3,500' and 6,600' elevation in a secluded mountainous area of northern B.C., approximately 100 miles by road southwest of Watson Lake in the Yukon Territory. Climatic conditions in this area range from mild warm in the summer, to extremely cold during the long winter period.The minesite itself is located over a mile above sea level at the top of McDame Mountain, where year round 24 hours per day miners extract the chrysotile ore from the surrounding waste by standard open pit techniques. The ore body dips into the mountain at about a 45° angle, and as the mining progresses, larger stripping ratios are required. Waste to ore ratio this year will be more than 10 to l whereas only a few years ago ratios of 3 or 4 to l were possible. After drilling, blasting, and loading by shovel onto trucks, the asbestos ore is transported to the Primary Crushing Plant for crushing prior to transport by aerial tramway more than three miles to the Concentrator and Mill in the valley below, where the fibre is extracted from the barren host rock serpentine and milled into numerous grades for shipment to asbestos users round the world. The major air usage is associated with the milling process, presently requiring over 500,000 CFM, with future requirements expected to exceed 840,000 CFM by the end of the decade."

Jan 1, 1976

By R. A. Jankowski

The U.S. Bureau of Mines (USBM) conducted a series of laboratory tests to investigate the effectiveness of using a flooded-bed scrubber with exhaust ventilation in deep-cut faces of up to 12.2 m in length. An experimental test program to determine the impact on respirable dust levels resulting from changes in face airflow, curtain setback distance, operator positioning, and operating parameters of the external spray system on the miner was completed. Gravimetric sampling was conducted in the immediate return and at three sampling locations on the off-curtain side of the entry. Statistically significant differences in dust levels on the order of 0.5 to 1.2 mg/m3 were observed between specific sampling locations and changes in several test parameters. Dust sampling results indicated that a flooded-bed scrubber and exhaust ventilation can be a viable dust control system for extracting deep cuts up to 12.2 m in length. The impact on methane was not evaluated.

Feb 24, 1997

By Henning E. Soderberg, Robert Brien, O&apos

Coal may be the answer to US energy problems, but it also has its drawbacks. If it is crushed, screened, dumped, or moved, the environmental engineer is faced with a dust problem. To control coal dust, at both minimum initial cost and reasonable operating cost, demands a working knowledge of dust control equipment design, as well as the coal handling operation. Here are some guidelines to reduce air volume requirements and cut overall system costs.

Jan 10, 1981

By Fred N. Kissell, Natesa I. Jayaraman

Introduction This paper describes a recent Bureau of Mines research project that resulted in a simple procedure for reducing the dust exposure of longwall shearer operators. This project involved the development and testing of a water spray and passive shield system to hold dust against the face and away from the shearer operators. This system is known as the Shearer- Clearer.

Jan 1, 1981

By Y. P. Chugh

Additional field evaluations of a modified continuous miner using a new spray system and modified scrubbers have been conducted by the authors. In this demonstration, a comprehensive package for dust control on a continuous miner which included previously developed modifications to the scrubber, scrubber intakes and the innovative chassis spray system was demonstrated. Side-by-side comparisons of the modified miner and regular miner indicated that the miner operator with the modified miner was exposed to 62% less respirable dust. Ram car operators with the modified miner had 38% less respirable dust exposure and the return air on the modified miner had 19% less respirable dust. The mining conditions during side-by-side testing were very comparable. These results support the findings of the modified spray system studies conducted earlier at different mines in Illinois on four occasions and the modified scrubber system field evaluation studies.

Jan 1, 2009

By J. P. Rider

Operating practices and resulting production from longwall faces are continually improving. Consequently, longwall operators are continually seeking to improve the dust control capabilities on longwalls. The National Institute for Occupational Safety and Health (NIOSH) has been conducting dust surveys at longwalls throughout the country in an effort to document the types of controls that are being used and to quantify the relative effectiveness of these controls. To date, surveys have been completed at longwalls in Alabama, Colorado, Pennsylvania, Utah, and West Virginia. In addition NIOSH has been reviewing longwall dust parameters provided by mine operators to MSHA to assess the status of dust control technology being used throughout the industry. Results from the underground dust surveys and information obtained from MSHA will be summarized in this paper to provide an update on longwall dust control technology and practices.

By Edward D. Thimons, Jay F. Colinet

Underground coal mining operations in the United States continue to increase productivity as mining equipment and practices are improved. Unfortunately, increased production also results in the potential for increased respirable dust generation and worker exposure. In response, US operations are applying basic controls at elevated levels and looking to emerging technologies in an effort to better control respirable dust levels. Ventilating air and water sprays remain the basis of dust control strategies for both longwall and continuous mining operations, and the level of application for these controls continues to increase. In addition, new technologies are emerging that have the potential to further reduce dust levels. The National Institute for Occupational Safety and Health (NIOSH) has been conducting research into methods to optimize existing control technologies and evaluate emerging control technologies. This paper will summarize control technologies routinely being used in underground coal mine operations, as well as provide a review of new controls that are being pursued.

By J. W. Austin

"Introduction The Brenda dust collection system was originally designed to handle air at the 5000 ft. elevation with less than 1 grain of dust per cubic feet of air handled. The temperature variation is from 32°C in the summer to -20°C in the winter.DUST COLLECTIONOriginal Equipment 1. Primary Crusher 2 compartment baghouse, shaker type design capacity - 17,000 cfm2. Primary Screening 3 compartment baghouse, shaker type design capacity - 30,000 cfm3. Secondary Crusher 4 compartment baghouse, shaker type design capacity - 45,000 cfm4. Secondary Screening 4 compartment baghouse, shaker typedesign capacity - 60,000 cfmThe original dust collecting equipment was designed using a napped terylene fabric at an air to cloth ratio of 5:1. The ducting was designed to handle the dust laden air at 3200 ft. per minute with all elbows and blast gate sections rubber lined. The hoods and the pickup velocities were designed to handle the anticipated low dust counts."

Jan 1, 1976

Reduce respirable dust exposure of workmen operating auger-type continuous mining machines. Approach: An auger miner was fitted with an exhaust system which draws dust laden air through a [scruber] and discharges it behind the line curtain. How It Works: Dusty air is drawn into the space above the coal conveyor and through a scrubber, by two fans mounted side by side above the conveyor. Exhaust from the fans passes through a duct to the side of the auger miner, and into tubing that runs back and into the air return passage formed by the line curtain. See Figure 1. Of the 5,000 cubic feet per minute of air normally entering the working place, 4/5 is drawn out through the dust exhaust system. The system was installed on a Wilcox Mark 20 Miner and tested underground by personnel of the Bureau's Pittsburgh, Pa., Mining and Safety Research Center, under a cost sharing

Jan 1, 1976

By Thomas. Lisa, Mark Coleman

Schenck Process is an established customer-driven solutions provider, utilising its knowledge, expertise and technologies to transform production processes. Operating across several industries Schenck Process have developed quality solutions from their range of equipment to solve problems and fill holes in other people’s processes. In the non-ferrous metals industries Schenck Process have been using their Clyde Brand solutions in Pneumatic Transport to solve problems on smelter sites for a number of years, handling of concentrates, additives and metallurgical dusts. Working alongside clients around the world they have developed a number of dust handling systems for flash furnaces from New Boliden, through Codelco to PASAR. Solving handling issues in dust collection has proved to suit Schenck Process range of equipment well and now a series of solutions are available. Solutions have been developed to handle materials up to 600°C and can convey over 1 km. Conveying to remote location for disposal, injecting directly into a furnace through lances, return to furnace burner feed, or deliver and dose into leaching reactors, Schenck Process are ready to ‘make processes work’. Historic solutions at New Boliden and Codelco demonstrate a range of material application and the long term performance of the equipment. Recent installations at Pasar utilise the Schenck new ProPhaseTM equipment and handle the Waste Heat Boiler and ESP dusts directly and simplify the dust train. The paper will seek to show how this equipment can bring benefit in handling high temperature materials directly and eliminate several traditional steps that are often unreliable. The systems can be paired with Schenck Process new PHASiQTM and STREAMiQTM control systems which are complete PC, HMI, PLC, Interface system with full SCADA, Data Storage and IoT ready remote interrogation and support available. Installed in this challenging environment the systems are ready for smelter use. The systems can be also joined to our new E-nizingTM web portal. A perfect partnership to deliver the trend in ‘Big Data’ while providing visibility and off site support. The paper will show how these systems can deliver reliable equipment and remote support for these often isolated sites as well as delivering rapid return on investment. This paper discusses a step change in simplifying Flash Furnace Dust handling which Schenck believes shows the truth of Schenck Process Solutions claim that ‘we make processes work’.

Jan 1, 2019

Bag stackers who use semi-automated palletizing machines and air slides may be exposed to high concentrations of dust. To reduce dust exposure, use an exhaust ventilation system in conjunction with an envelope of clean air over the bagstacker provided by an overhead air supply. Description of Hazard Mineral processing plants in the United States and throughout the world process material that is finely ground and placed into bags for shipping to the consumer. These bags normally range from 50 to 100 pounds in weight. Once the material is placed in these bags, a bag stacker loads the bags onto pallets. A bag stacker is exposed to a lot of dust that is mainly released by the force from loading the bag onto the pallet. The two main sources are the dust on the outside of the bag and the dust that escapes from inside the bag as it is loaded. The Mine Safety and Health Administration's (MSHA) records indicate the bag stacker's dust exposure is one of the highest of all workers at mineral processing operations. Ways to reduce the dust exposure and strain to the bag stacker are in constant development. Recently, automated systems have been built. These systems range from fully automated, which totally remove the worker from the bag-stacking process, to semiautomated systems, in which the bag stacker still performs some of the functions. This Hazard Control deals with controlling the bag stacker's dust exposure during use of a semi-automated palletizing machine. The worker slides the bags into position on the palletizing machine. Once an entire layer of bags is positioned, the bag stacker operates the controls on the palletizing machine to lower the layer of bags onto the pallet. An air slide is built into the semi-automated palletizing machine so the bags are easier to move. This slide uses a metal table with air jets that exit through small holes at high velocities, similar to an air hockey game. The dust problem occurs because the air slide causes dust to blow up onto the bag stacker, significantly increasing the dust exposure.

Jan 7, 2001

By Andrew Cecala, John Organiscak, William Heitbrink

Many types of heavy equipment used in the mining and construction industries use enclosed cabs to protect equipment operators from dust and noise exposure. Normally, when the equip- [ ] ment is new, manufacturers' deigned controls are effective at keeping the operator's exposure at acceptable level. However, as equipment becomes older and many components of the enclosure deteriorate, such as gaskets and seals, the effectiveness of the enclosed cab can be greatly reduced. This can cause excessive and dangerous exposures to respirable dust, especially when the ore or overburden contains crystalline silica.

By Mike Cammack, Logan Huppert, Gustavo Azpilcueta

During the summer of 2015, Unisea Inc. sought proposals for the G1 Dock Replacement Project in Dutch Harbor, Alaska. It would be a one year project and construction was scheduled to begin in the spring of 2016. One aspect of the project was the requirement for a layer of armor stone to protect part of the dock. An estimated 30,500 tonnes (37,670 t) of armor stone were needed for the project. The source of rock was the Unisea Quarry due to its proximity to the project and the quality of the stone meeting all the required technical standards.

Jan 1, 2018

By Marc D. Melker, Geoffrey R. Lane, Michael Jahraus

"The Cresson gold deposit is located in the Cripple Creek district of Colorado. The deposit is composed of volcanic intrusive rocks and volcanogenic sediments where gold mineralization is associated with veins and cavities within a diatremal breccia.The purpose of the current study was to:1. Determine the penetration potential of the Cripple Creek Breccia.2. Assess the relationship between penetration and gold recovery within the Breccia.Two methods were applied using a cyanide solution containing ultraviolet sensitive dye to elucidate pathways of penetration within the rock. The first involved stagnant soaking of twoinch square pieces within the solution. The second method involved column leaching of ~100kg of Breccia crushed to P80 12.7 mm (0.5 inch). Samples were selected at specified intervals to capture the penetration progress of the solution. Photomicrographs and image analysis were utilized to illustrate and quantify the degree of penetration.Results indicated that the maximum penetration for the Cripple Creek Breccia (85 to 97%) due to a porous and permeable groundmass, containing large non-porous lapilli fragments. In addition, ~90% of leachable gold was recovered with only ~50% rock penetration.INTRODUCTIONDye penetration studies were first developed at SGS-Lakefield Research for the purpose of determining the fluid penetration amenability of differing rock types. The method was to place a large rock or drill core in a pan with 1 to 2 inches of a pre-mixed, water based fluorescent dye. The sample was sequentially cut after prescribed time periods to reveal a fresh surface. The cut surface was photographed under long wave ultraviolet light, and the same piece returned to the dye and allowed to sit until the next prescribed cutting."

Jan 1, 2006

By Lucian Bogdan

On many occasions during construction and service life of the structure, it is crucial to know the load in post tensioning tendons and anchors. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive and the accuracy differs depending on the method used Dyna Force sensor uses the Elasto-magnetic technology (EM) and non destructive testing (NDT) to direct measure stress level in prestressed strands or bars installed on ground anchors or post tensioning tendons. Dyna Force sensor can be used to rapidly read the change in load during proof and performance tests and compare with the pressure gauge and during the life on the anchor to monitor existing lock-off load. It can be used also to determine the load along the bonded length of the anchor allowing the contractor to increase or decrease this length. The paper presents Dyna Force operating principle and some applications. In conclusion, the Elasto magnetic technology applied through Dyna Force is a new and easy to use approach to monitor anchor load during proof test and service life of the structure.

Jan 1, 2009

By Chris D. Thompson

In Southern Ontario, Canada, piles are frequently driven through competent clayey soils to obtain end bearing on extremely dense till or bedrock. One reason for this is the difficulty at assessing the adhesion of the clayey soils. This is illustrated by texts, such as the Canadian Foundation Engineering Manual, which is the standard of practice in Canada, that indicate that theoretical analysis of the adhesion values of such soils are unreliable. In this paper, the results of high strain dynamic testing have been used to estimate the shaft resistance of 11 closed end pipe piles driven in overconsolidated very stiff to hard clayey tills at four sites by means of the CAPWAP wave equation analysis. More than twenty-five years of experience with bearing capacity predictions by such means have developed considerable confidence in its accuracy. The results were found to correlate reasonably with the average Standard Penetration Resistances of the clays at the sites. There was a linear relationship between an adhesion of 64 kPa at 20 blows per 300 mm and 192 kPa at 60 blows per 300 mm. At one site, 6 piles were tested and found to have a wide range of Standard Penetration Resistance and estimated adhesion in the same stratum. While there was significant scatter of the results, piles would have been safe at design loads obtained from the relationships established by the analysis carried out for this paper after applying appropriate factors of safety.

Jan 1, 2002