Search Documents

By H. B. Charmbury, D. R. Mitchell

Everyone in the coal industry from top management to the preparation engineer is vitally interterested in recovering as much salable coal as possible from the run-of-mine product. Coal losses from a preparation plant occur in the solid refuse material being discharged from the plant and in the bleed-off slurry from the water circuit. The refuse is generally hauled from the plant in solid form by trucks, conveyors, or aerial trams to the refuse or culm banks or it may be crushed and transported by hydraulic methods to refuse ponds or dams. The loss of coal in refuse material and the extent of this problem has been covered in another paver.' The loss of salable coal in the plant bleed-off slurry is one of the water circuit problems in coal preparation plants. Slurries originate at various places in the processing circuits and are usually disposed of by transportation to waste ponds known as slurry ponds. Even though the combustible material discharged as slurry and refuse from the plant is labeled a loss, the loss must only be considered temporary. There is a tendency at the present time to examine refuse and slurry losses and to reprocess these materials to recover valuable coal. Slurries from eight bituminous coal preparation plants in central and western Pennsylvania have been sampled and examined to determine the amount of recoverable coal in each. Examinations of the samples were made to determine the tons per hour of solids and the gallons per minute of water in the slurry; the size, ash, and sulfur analyses of the solids; and the sink-float characteristics of the larger solids. The extreme fines (—325 mesh material) from one of the samples has been examined further to determine the micron size fractions as well as the ash and sulfur content of the micron sizes. Collection of the Samples: Field trips were made to each of the plants where samples were obtained and discussions held with the preparation engineer prior to sampling. The flowsheet of the plant operation was studied and a time-period selected to obtain a representative sample. At least 20 1-gal samples of total plant bleed-off suspensions were collected at each plant in increments over designated periods belived to be typical of the plant flow Three of the samples were obtained from plants in the Pittsburgh area. Each plant supplied information on the capacity, operating time, type of cleaning equipment used, water and material balances, and auxiliary equipment. From the time required to collect given amounts of slurry and from the amount of solids in the slurry, total solids discharges from the plant were calculated and compared with the plant flow. Ash and sulfur analyses of the total solids were also checked, at some plants, with company figures. In all cases where checks could be made there was reasonable agreement between company figures and those reported here. Analysis of the Slurries: Representative fractions of properly agitated samples were examined in the laboratory to determine the specific gravities of the slurries. The solids and water were separated by filtration to check the weight of each so that the percent of solids in the pulp could be determined. From the resulting data, presented in Table I, it may be seen that the percent solids in the slurries ranges from 2.8 to 39.0 and the amount of solids from 2.61 to 45.61 tph. Size Analysis of Solids: Representative fractions of the slurries were permitted to settle and the clear water was removed by siphoning. The solids were then wet-screened at 28, 35, 48, 65, 100, 150, 200 and 325 mesh. Results of the size analyses are presented in Table 11. These results indicate the extreme variation of sizes and in most cases the degree of fineness of the solids. The amount of —325 mesh ranges from 22.5 to 84.5 pct and the amount of+200 mesh from 8.3 to 69.1 pct.

Jan 1, 1961

By E. E. Donath

Application of the coal hydrogenation process for the production of chemicals is described. It has been estimated that a plant to produce 31,090 bbl per day of chemicals and fuels would cost $326,- 000,000. These products would consist of 6.1 pct by weight tar acids, 50.8 pct aroma tics, 16.4 pct LPG, and 26.7 pct gasoline. THE coal hydrogenation process is well known as a means for the production of liquid fuels from coal. In this paper the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid phase and vapor phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high molecular weight aro-matics and of tar acids and tar bases. The relative amounts of heavy and middle oil—boiling above and below, e.g., 325°C—can be influenced by temperature, residence time, and catalyst of the liquid phase hydrogenation. In the vapor phase hydrogenation a solid bed catalyst is used to convert the intermediate oil from the liquid phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring compound content of the liquid phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparaffins.' Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig. 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid phase hydrogenation stage, coal is made into a paste with recycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydrogen enter high pressure converters where the liquefaction of coal, conversion of the high boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470°C. The reaction products enter the hot catchpot in which lower boiling oil vapors are separated from the residue containing unreacted coal, ash, and heavy oil. This residue, usually called H.O.L.D. (heavy oil let down), is processed to separate solid and liquid material. By thermal treatment of the residue, e.g., a coking process, distillate oil is obtained, which can be recycled as part of the pasting oil. This stream is rich in polynuclear aromatics and can be, and has been, used for the recovery of such material. The oil vapors and hydrogen from the hot catchpot are cooled in heat exchangers and a cooler, and the condensed oil is separated from the recycle hy-

Jan 1, 1953

By E. E. Donath

Application of the coal hydrogenation process for the production of chemicals is described. It has been estimated that a plant to produce 31,090 bbl per day of chemicals and fuels would cost $326,- 000,000. These products would consist of 6.1 pct by weight tar acids, 50.8 pct aroma tics, 16.4 pct LPG, and 26.7 pct gasoline. THE coal hydrogenation process is well known as a means for the production of liquid fuels from coal. In this paper the possibilities of the coal hydrogenation process as a source of chemical raw materials will be discussed. The recovery of chemicals from coal hydrogenation products necessitates some modifications and additions to the equipment used for the production of fuels. The conversion of coal into liquid fuels such as gasoline requires two steps: liquid phase and vapor phase hydrogenation. Intermediate oils obtained in the liquid phase contain oxygen and nitrogen compounds, especially aromatic compounds, since the coal itself is composed mainly of cyclic compounds. These oils are the raw material for the separation of high molecular weight aro-matics and of tar acids and tar bases. The relative amounts of heavy and middle oil—boiling above and below, e.g., 325°C—can be influenced by temperature, residence time, and catalyst of the liquid phase hydrogenation. In the vapor phase hydrogenation a solid bed catalyst is used to convert the intermediate oil from the liquid phase operation into hydrocarbons of the gasoline boiling range. Essentially pure hydrocarbons with a low content of sulphur, oxygen, nitrogen, and olefines are obtained. Depending mainly on the catalyst, the high ring compound content of the liquid phase oil can be preserved and gasoline rich in aromatics obtained. However, with other catalysts, these ring compounds can be split into gasoline with a high content of isoparaffins.' Again, depending on the operating conditions, products of varying boiling range can be obtained. Selection of catalyst and operating conditions therefore makes possible the production of different grades of motor fuel and also variations in the relative amounts of benzene, toluene, and xylene when aromatic hydrocarbons are produced. The schematic flowsheet, Fig. 1, shows the main steps of the coal hydrogenation process, and the product streams used for the recovery of chemicals are indicated. In the liquid phase hydrogenation stage, coal is made into a paste with recycle heavy oil. The coal paste is mixed with hydrogen and preheated at a pressure of 300 to 700 atm in heat exchangers and preheaters. The coal paste and hydrogen enter high pressure converters where the liquefaction of coal, conversion of the high boiling liquid materials initially obtained, into intermediate oils is performed at a temperature around 470°C. The reaction products enter the hot catchpot in which lower boiling oil vapors are separated from the residue containing unreacted coal, ash, and heavy oil. This residue, usually called H.O.L.D. (heavy oil let down), is processed to separate solid and liquid material. By thermal treatment of the residue, e.g., a coking process, distillate oil is obtained, which can be recycled as part of the pasting oil. This stream is rich in polynuclear aromatics and can be, and has been, used for the recovery of such material. The oil vapors and hydrogen from the hot catchpot are cooled in heat exchangers and a cooler, and the condensed oil is separated from the recycle hy-

Jan 1, 1953

By H. J. Gluiskoter

The chlorine content of the coals in the Illinois Basin ranges from 0.00% to more than 0.60%. The chlorine content of the Herrin (No. 6) Coal has been mapped on a regional scale and, in general, increases with the depth of the coal. The depth-chlorine correlation exists because the coal is in apparent equilibrium with the composition of the ground water associated with it, and the salinity of the ground water generally increases with depth. At least part of the chlorine can be easily removed from the coal in the laboratory. In a natural weathering experiment, chlorine values decreased markedly during an 8-week period. Results to date indicate that none of the coals studied has a sufficiently high chlorine content to make it unusable in high-temperature steam boilers, although special steps may be necessary in the preparation or utilization of some of the highest chlorine coals. Investigations into the occurrence and distribution of chlorine in Illinois coals have been in progress at the Illinois State Geological Survey for over 35 years. Since 1948, chlorine analyses of face channel samples and of drill core samples of coal have been made routinely. The increased interest in chlorine and alkalies in coal in the U.S. followed that in Europe, where power plants during World War II were called upon to produce at higher levels than previously and with less down time for maintenance. Higher steam temperatures were reached, resulting in increases in the amount of fouling of external heating surfaces and in corrosion of boiler tubes when high chlorine coals were used. Early studies of the problem showed that coals with high chlorine content were more likely than those low in chlorine to cause difficulties in installations fired with powdered fuel. Crossleyl reported that the first rule of thumb developed for British coals was that coals considered to be high in chlorine (more than 0.30%) caused the most trouble, those intermediate in chlorine content (0.15% to 0.30%) were less likely to cause difficulties and those low in chlorine (less than 0.15%) generally were not associated with alkali bonded deposits and corrosion. However, this relatively simple picture was not adequate to characterize the difficulties that could be expected during the utilization of a large number of coals and Crossley1 developed another scheme for assessing the chances of superheater corrosion. This scheme took into consideration the observation that coals high in sulfur as well as chlorine are more likely to cause corrosion and fouling than coals low in sulfur and high in chlorine. Crossley also considered the ash content. When two coals had the same chlorine and sulfur contents, the one with the greater amount of ash would be the less likely to cause difficulties. Knowing only the amount of chlorine in a coal obviously will not give all the answers. Indeed, the significance of the chlorine content has been much discussed and it has been suggested that perhaps the total alkalies are a better indicator of possible troubles. The observation that the deposits that form

Jan 1, 1968

By T. S. Spicer

The relationship of coal characteristics to the principal types of firing equipment has been known to the coal combustion engineer, but is not as familiar a subject for purchasing agents, salesmen, consumers, and executives of coal-producing and consuming companies. This general survey of characteristics determined by standard laboratory tests, of major types of combustion techniques, and of the relationships between the two is directed toward the latter audience. It will also serve as a review for those actively engaged in the combustion of coal. Although the relationship of coal characteristics to the principal types of firing equipment is well known to the experienced coal combustion engineer, apparently there is need for a summary article on this subject. The author has received numerous requests for such a paper from purchasing agents, coal salesmen, coal customers and executives of coal-producing and consuming companies. Consequently, the scope of this paper will be directed to this audience, with the hope that it may serve also as a review to others actively engaged in the combustion of coal. The magnitude of this subject is so great that only a brief general treatise is possible. The author realizes that because there are so many special cases and exceptions to the generalities which follow, he is in jeopardy of contradicting himself. It is the hope, however, that the many references cited will prove valuable to those who wish to study the details excluded by necessity, due to space and time limitations. Hence, the characteristics of coals as determined by standard laboratory tests will be discussed; the major types of combustion techniques reviewed; and then the characteristics and firing will be related. CHARACTERISTICS OF UNITED STATES COALS The coals of the United States range from lignite to anthracite and each has its own general characteristics. The extensive coal fields of the U. S. are shown in Fig. 1 and the estimated reserve according to rank for each state is illustrated in Fig. 2. Coals may be classified according to rank as shown by Table I from the ASTM Standards on Coal and Coke, D-338-38.1 The basis of this classification is ac- cording to fixed carbon and heating value (Btu per pound) calculated to a mineral-matter-free basis. The high-rank coals are classified according to fixed carbon on the dry basis; and the low-rank coals according to Btu on the moist basis. Agglomerating and slacking (weathering) indices are used to differentiate between certain adjacent groups. While rank is not itself a characteristic it does signify certain characteristics that accompany a class of fuel. Anthracite, for example, immediately implies a hard, free-burning, smokeless coal of low volatile matter, usually having an ash of high fusibility. Coals may also be classified according to grade as described by ASTM Designation D-398-37.1 This quality classification is determined by size, calorific value, ash, ash-softening temperature, and sulfur. This type of classification is not used as extensively by the industry as the rank classification. Fig. 3 shows the heat value of different ranks compared to proximate analyses. Coals may also be classified by sizes, as shown in Tables IIA and IIB, and sizes can be on both top and bottom limits. If this is done, then the coal is called double screened; otherwise, either top or bottom sizes can be specified as a limit. Bituminous coal sizing varies from field to field and depends upon the market demand. The common sizes and their main uses are outlined in Table IIA. Anthracite is usually available in many sizes at the colliery, and Table IIB summarizes standard sizes and names. Although rank, grade, and size designations help identify and describe a coal in question, there still remain other characteristics such as indicated by moisture, free swelling index, grindability tests, etc. A bituminous coal information chart Table III) suggested for use in studying the available coals in a region, lists origin and chemical and physical characteristics. Even this more comprehensive list does not completely spell out all the characteristics of a heterogenous material like coal. For example,

Jan 1, 1961

By M. A. Elliott

The technology of gasifying coal to produce synthesis and pipeline gas has advanced significantly in the Past 20 to 30 years. This period has seen the extensive use of oxygen in coal gasification, the development of suspension gasification processes and fluidized-bed gasifiers, the operation of various gasification processes at elevated pressures, and operation of gasifiers under slagging conditions. These developments are discussed, and their application to commercial and pilot plant gasifiers is reviewed. Typical processes for synthesis gas production are described, and operating results are compared. Pipeline or high-Btu gas may be produced from coal either by catalytic conversion of synthesis gas to methane, or by the direct reaction of coal with hydrogen (hydrogasification) to produce a methane-rich gas. Neither of these methods has been applied commercially, but developments pertaining to each of them are reviewed, and general processing schemes are discussed. The use of coal as a raw material for manufacturing gas has a long and distinguished history. In fact, the gas industry began in the early 1800's when William Murdock demonstrated that it was feasible to produce and distribute gas made by retorting coal. Coal was used exclusively for gas manufacture until the middle of the 19th centruy, when Lowe invented the carbureted water gas process. In that process, coke was one of the raw materials used, so coal was still an important factor in gas manufacture. However the availability and relatively low cost of natural gas in the United States, and its widespread distribution by long-distance pipelines in recent years, has virtually eliminated the use of coal as a raw material for gas manufacture in this country. It should not be inferred from the foregoing that the technology of coal gasification has remained static in the United States and abroad. In fact, in the past two decades many new concepts have been developed in both the science and the technology of gasification. This progress has been a result of the considerable expansion in research on the fundamental chemistry and physics of gasification reactions, and in development work on gasification processes. This expansion in effort stems in part from increased interest in the use of gas as a raw material for the synthesis of chemicals and liquid fuels, and in part from the need to develop methods for gasifying coal and other solid fossil fuels to ensure a long-range supply of energy in the form of gaseous fuel. In these uses of gas, synthesis gas, a mixture of hydrogen and carbon monoxide in various proportions, is the starting material. It may be converted catalytically to gaseous and liquid hydrocarbons and other chemicals, or to hydrogen for use in hydrogenation or reduction reactions. Since coal is our most abundant fossil fuel, it is inevitable that one day it will regain its prominence as a raw material for gas manufacture. It is of interest, therefore, to consider the present status of gasification technology, directing attention particularly to advances made in recent years. Inasmuch as many comprehensive treatises l-3 and review4-7 of gasification technology are available, no attempt will be made in the present review to cover all processes in detail. Instead, the discussion will be concerned chiefly with typical processes embodying the advances that are most likely to be generally applied. ADVANCES IN GASIFICATION TECHNOLOGY For purposes of this discussion the starting point will be the conventional processes that were used for many years for the complete gasification of coal. These were: 1) carbonization in coke ovens followed by gasification of coke with air and steam in cyclic water-gas generators, and 2) fixed-bed air-blown producers. Both of these methods have obvious deficiencies when we consider that the ideal complete gasification process would be a single-stage, continuous

Jan 1, 1961

By Hubert E. Risser

Although, for about a half-century the percentage of coal production provided through strip mining has steadily increased, recent trends indicate that a peak in percentage (not tonnage) is being approached, principally because of the decline in economic adrantage enjoyed by strip mining compared to underground mining. Factors contributing to the decline are the decrease in the margin of advantage in manpower requirements held by strip mining; an increase in depth and volume of overhurden, requiring larger equipment and capital investment; increasing lack of reserve land blocks large enough to support extensive strip mining operations; more stringent legislation for reclamation of stripped land, with increasingly higher costs of such reclamation; and the increasing costs of land surface rights for strip mining. Already there has been a peak and suhsequent decline in relative importance of strip mining insome major Eastern coal-producing states; trends indicate that a peaking for the whole Eastern region is on the way. Although, in the West the pressures are less severe, they will, nevertheless, reduce to an increasing degree the advantage that strip mining has possessed. For about half a century, strip mining has been providing an ever-increasing share of total coal output in the United States, and in the past 30 years this share has grown from less than 8% to 33.7%, as shown in Fig. 1. Fig. 1 also shows that strip mining is gaining faster in the West than in the East. From 1961 to 1967, output from strip mines grew 63.6 million toqs, or 52.2%. Certainly there is nothing in such performance to indicate any peaking in the level of strip coal-mine production. But the fact is that, if not in actual tonnage, strip mining appears to be reaching its peak in relative importance, at least east of the Mississippi River. And the area east of the Mississippi provides 90.0% of the strip and 94.9% of the total coal production of the nation. The relative economic advantage which spurred strip mining's growth for a third of a century has been diminishing markedly in recent years. Fig. 2 shows evidence of this decline. From 1947 until 1961, strip tonnage output remained fairly stable, at the end of the period showing only a 12.5% decline. Meanwhile, underground coal production fell 44.5%. As the result of the greater decline in underground coal, strip coal in 1961 furnished 30.3% of the total coal produced, compared to only 22.1% in 1947. In the succeeding six years, however, underground coal output increased by 76.5 million tons, while strip output increased only 63.6 million. Further evidence of the strengthening of underground coal's relative position — or if you will, the weakening of strip coal's position — can be found in the major coal stripping states: Illinois, West Kentucky, Ohio, Pennsylvania, Indiana, and West Virginia, which in 1966 provided 80% of the nation's strip coal. Fig. 3 shows what has been happening in three states lying in the Appalachian field and in the total output of these three states. In the figure, the column height represents the output of coal mined by all methods. The number at the base of each column is the percentage mined by stripping. In Pennsylvania and Ohio, the percentage of strip mining increased between 1956 and 1961, but by 1966 had declined from the 1961 level. In West Virginia, a decline occurred during the first five years but was followed by a rise. In January 1968, Coal Age published an article listing the locations and capacities of new large mines in the planning and construction stages that would be operating by 1968-1971. The plans for West Virginia and Pennsylvania indicated all the new mines would be underground. Except to the extent they might replace existing under-

Jan 1, 1970

By L. A. Updegraff

Before discussing the application of capacitance for the measurement of moisture content in a moving stream of coal it might be well to first give a brief description of the process and then show how it can be applied to the coal industry. A capacitor may be described as a device having two conductors separated by an insulator, the conductors hereafter being designated as a test cell or test plates and the insulator as the dielectric. Capacitance, therefore, is a measure of the ability of a capacitor to store an electrical charge. Two basic factors that affect capacitance are the dimensions of the capacitor and the dielectric constant of the insulator. Capacitor dimensions which affect its capacity are the area A of the conductive surface, and the distance d between plates. Capacitance is inversely proportional to the distance between plates and directly proportional to area A, so if capacitance is indicated as C and the dielectric constant as K the equation for capacitance would be C = AK/d. The dielectric constant can be described as the ratio of the actual capacitance of any given material to that of a vacuum, which is unity. In industrial applications the area of the plates remains constant as also does the distance between them, leaving the dielectric constant as the only variable to affect the capacitance measurement. Figure 1 is a schematic diagram of an r-f excited capacitance bridge in which a test cell is part of the circuit. This bridge consists of four capacitors in two pairs connected across an a-c voltage source. In one side of the circuit the two capacitors are fixed but in the other side they are variable, one being the rebalance capacitor operated by the servo motor and the other the test plates between which the dielectric passes. Capacity of the plates is a function of the dielectric constant of the material between them and is measured at radio frequency. Within the recording instrument is an r-f oscillator and a 60 c ps modulator. The radio frequency signal is generated by the oscillator, modulated by a 60 cps wave, and sent to the bridge. Therefore the signal entering the capacitive bridge is a radio frequency carrier with a 60 cycle envelope, If the bridge is in balance as the signal enters there would be no voltage drop and so no output by the detector. As long as the dielectric constant remains the same the bridge will stay in balance. However, any change in the dielectric constant, which in this case would be a change in moisture content, would affect the bridge. Higher moisture increases the capacity of the test cell which causes less voltage to develop across it causing imbalance of the bridge. This in turn causes a radio frequency signal to appear at the detector. Output from the detector is a 60 cycle ripple which is in proportion to the imbalance of the circuit. A 60 cycle amplifier boosts the detector signal to enough power to drive the servo motor which positions the recording pen and also rotates the variable capacitor, to which it is mechanically connected, to bring the bridge back in balance. An increase in moisture causes the servo motor to rotate in one direction, but a decrease causes imbalance in the opposite direction, and thus rotates the motor in that direction. This brings the bridge back in balance and stops the motor. The bridge shown in Figure 1 has been modified so as to provide a wide range of adjustments. Coarse and fine span adjustments located in the recording instrument are set to govern the amount of pen movement for a given change in capacitance. A measuring head unit contains coarse and fine zero adjustments for

Jan 1, 1961

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems. It is equally important to realize that most coal mines will require one or more conventional loader setups in the plan of total mechanization. Seam variations, adverse physical conditions, and special designs of main headings for haulage and ventilation, to name only three reasons, may render 100 pct use of continuous miners uneconomical. Of course, this situation may change. In one mine, prior to 1954, machines that ripped coal from the face achieved only average results, as compared to the impressive performance of boring-type units in another coal mine. A boring-type unit was therefore selected for the first mine in the belief that the chance of success would be greater if it were used in a combined cutting and wedging operation, cutting a full face in its forward movement. The miner was located in a part of the mine where a special projection could be readily developed, a solid area scheduled for mining according to the overall progress plan. All openings surrounding the particular area were carefully investigated for the presence of sulfur balls. Fig. 1 (opposite) shows the representative seam section, containing the several pyritic bands 1/4 to 1/2 in. thick; a characteristic Pittsburgh seam parting averaging 5 to 6 in. of slate, coal, and slate; and the occasional py-rite lenses 2 to 3 in. thick. Under normal conventional mining methods, the top 10 or 12 in. and the bottom 4 in. are left in place to offer roof protection

Jan 1, 1958

By P. D. Rao, H. B. Charmbury, D. R. Mitchell

As a result of a changing market pattern for anthracite, there is now an increasing demand for steam size and a decreasing demand for domestic sizes. To help the producer meet this new demand, the authors present the technical aspects of the problem of crushing domestic sizes to steam fineness and size. The market pattern for anthracite coal has changed considerably in recent years. The demand for domestic sizes has been gradually decreasing and the demand for the steam sizes has been increasing. The companies however aim for a maximum production of domestic sizes, since these sizes command premium prices. To meet the market demands, particularly in certain periods of the year, further size reduction of the coarse clean coal is necessary. The present practice of multistage crushing in toothed rolls leads to complicated flow arrangements and is high in cost. Data presented herein indicate that crushers with high reduction ratios could be used with a resulting simplification of crushing flows and an appreciable reduction of capital and operating costs. The different types of crushing equipment investigated included the rotary-type breaker, the jaw crusher, the impactor-type crusher, and the Aerofall mill. CURRENT PRACTICE The standard sizes of anthracite are presented in Table I and market specifications require that any given size be maintained with only a limited amount of oversize and undersize material. The 1958 prices of the various sizes also are presented, so it may be seen that size reduction is only performed when dictated by market demands. At the present time the general practice of crushing anthracite consists of removing the top size and crushing it in a toothed double roll crusher to the next largest size. Consequently, to reduce the domestic egg, stove, and nut sizes to steam sizes of pea, buck, rice, and barley, the original material must be screened to produce the three top sizes and each size must be crushed in three separate rolls to the next largest size. Each crushed product must then be rescreened to remove the oversize for re crush ing. Thus a typical operation would consist of scalping the egg size from a mixture, crushing it to stove size, and rescreening the product. This same cycle would be repeated for the stove and nut sizes requiring three screens and three crushers as well as conveying equipment to handle the crushed products. This results in an expensive series of operations to make a product which sells for a lower price. If the three top sizes are crushed in one operation to the smaller sizes then the yield of steam sizes is low and the production of Nos. 4 and 5 sizes is large. These sizes sell for lower prices than the steam sizes. A typical operation is presented in Fig. 1. From the figure it may be seen that the original cleaned anthracite contains 67.4 pet domestic sizes, 26.4 pct steam sizes, and 6.2 pct fines. After multistage crushing of the domestic to steam sizes the composition of the product is 0.6 pct domestic sizes, 89.6 pct steam sizes, and 9.8 pct fines. From a technical standpoint these results are reasonable but the handling and crushing costs are

Jan 1, 1961

By H. E. Criner, M. G. Driessen

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By M. G. Driessen, H. E. Criner

THE cyclone thickener has two important applications in wet washing plants: (1) water clarification, and (2) fine coal recovery. The thickener consists of a conical chamber into which the fluid is injected through a tangential nozzle at the periphery of the large end. The solids of the slurry are concentrated and removed from the apex of the cone while the "thinner" portion is discharged from a central tube in a flat head at the large end, fig. 1. The advantages of the cyclone thickener are that large volumes of slurry may be treated with small space requirements and that the underflow concentration may be controlled easily and readily to meet varying feed conditions. Control of Washery Water Solids Concentration: The first requirement, in the process of controlling solids concentration, is that the solids be removed from the body of circulating water at the rate at which they are introduced. If this condition is satisfied the concentration will remain at a fixed value and will not increase to uncontrollable levels. The second requirement is that the solids concentration

Jan 1, 1951

By J. Mason

In order that the use of continuous mining machines be most economic, the equipment must be operated at rated capacity as much of the time as possible and downtime for repairs kept at a minimum. A large factor influencing any proposals for maintenance programs is the complexity of the machines—often the intricacies of the precision-built equipment requires engineering knowledge byond the scope of mine maintenance personnel. A training program is part of the answer; there are others. In addition to investigating a joint company-manufacturer equipment-design improvement program, Mountaineer Coal Co. has launched a detailed preventive maintenance program to combat extensive downtime often encountered when continuous miners are used. Everyone in the coal industry knows the importance of operating continuous miners at their rated capacity as much of the time as possible. The potential capacity of the miner is such that l-min. delay means from 3 to 8 tons of coal lost. Today's miner is a well designed, precision-built machine, complicated with hydraulic and electrical equipment and complex mechanical assemblies with all possible combinations of gears, levers, and rods. As the machine becomes more complex, the problem of maintenance becomes more acute. The transition from conventional to continuous mining has taken place so rapidly that the mine mechanic has been unable to keep pace. When there is a machine failure, the maintenance man usually employs either the trial-and-error or the play -it-by-ear method of repair, but this represents an expensive proposition. Mine mechanics, maintenance superintendents, and mine managers complain about the complexity of the machines and how difficult it is to keep them running. There is no shortage of skill in the design offices. Machines are designed by good engineers, but for engineers. What's the answer? Better trained maintenance men—better maintenance instruction—better field service. These are all good corrective measures, but the real cure is to provide for the men at the do it level. Designers have got to cooperate with men to simplify maintenance on the increasingly complex machine. The designer must be aware of how his machine can be maintained. Sometimes a simple design change in a bearing, oil seal, or a bushing will correct recurrent breakdowns. Parts such as filters, hydraulic cylinders, hoses, and pivot pins can be better arranged on the machine to make them accessible so that the mine mechanic can easily keep the machine producing. Therefore, to get our maintenance off on the right foot, the program must begin back in the design office, before the machine is delivered to the mine property. Realizing the importance of this aspect, our company set out on a joint company-manufacturer equipment-design improvement program. This is a formal program in which quarterly reports are written covering machine defects, design weakness, and general problems relating to machine maintenance and performance. The manufacturer in turn comments on each and every item appearing in these reports, indicating the action he proposes to take. In addition to the written reply, meetings are scheduled with manufacturer representatives to discuss further the outlined problems. The benefits realized from this organized program are both substantial and far reaching. Good maintenance begins with a good design. The subject of preventive maintenance is not a new one. Volumes have already been written on the subject. It consists primarily of doing the maintenance work when you want to rather than when the machine demands it. However, a preventive maintenance program can be overdone. Theoretically, if carried to ridiculous extreme, all working time could be spent inspecting and repairing the machines and no time would be left for production output. Our goal in maintenance is to maximize running time for all machines, and to prevent or at least minimize production downtime. INSPECTION AND REPORTING The center of any preventive maintenance schedule is regular and systematic inspection, but it must be

Jan 1, 1961

By G. H. Gronhovd, W. H. Oppelt

Complete gasification to produce synthesis gas for manufacture of synthetic chemicals and fuels offers possibilities for utilization of the vast lignite fuel deposits in the U.S. The design of a slugging, fixed-bed, pressure gasification pilot Plant is described. Results are presented for initial operation of the plant at moderate pressure and using low-temperature char as fuel. Gasification of solid fuels is becoming increasingly important in the future overall energy picture, both in this country and abroad. Snythesis gas from gasification of coal consists chiefly of carbon monoxide and hydrogen, and after suitable purification and modification this gas can be used in the production of synthetic ammonia, methanol, higher alcohols, and synthetic liquid fuels, or as a reducing gas in the metallurgical field.' Most synthesis gas used in this country is made from natural gas, petroleum oils, and refining tail-gases, but the direct gasification of coal will become more attractive as costs of petroleum oils and natural gas increase.' A gasification process designed for use with brown coal and lignite was developed by the German Lurgi Co. prior to World War 11. In this process a fixed bed of lump-sized fuel is gasified with steam and oxygen at pressures ranging from 370 to 440 psi. Effective heat exchange between the ascending high-temperature gases and the descending solid fuel results in low gas outlet temperatures, high thermal efficiency, and favorable oxygen consumption. Lurgi gasifiers are used commercially for the production of synthesis gas or as a substitute for coal gas in many countries, including Germany, Czechslovakia, Great Britain, South Africa, Australia and Pakistan.3-6 The chief disadvantage of the conventional Lurgi gasifier which operates under nonclinkering conditions is that large quantities of excess steam must be supplied with the oxygen-steam mixture to reduce the temperature in the fuel bed below fusion temperature of the ash. Most of the steam leaves the gasifier undecomposed with the product gas and, after cooling, produces large amounts of dilute liquor. Evaluation of fixed-bed gasification experiments using dry-ash removal indicated that by increasing the oxygen concentration in the oxygen-steam blast the temperature in the combustion zone could be raised high enough to operate under slagging conditions. 7-8 Operation of a fixed-bed pressure gasifier under slagging conditions would reduce the steam requirements and the volume of waste liquor and would increase the steam decomposition, the overall thermal efficiency of the process, and the rate of gas production per unit cross sectional area of the gasifier. Because the Lurgi gasification process, modified for slagging operation, offered possibilities for efficient gasification of American lignite, the Bureau of Mines decided to investigate the process on a pilot-plant scale at the Grand Forks, N. D., Lignite Research Laboratory. DESIGN Description of Pilot Plant: A flowsheet of the Grand Forks slagging gasification pilot plant is presented in Fig. 1. The gasifier unit consits of the coal lock, the gas generator, and the slag lock. The fuel, which is periodically charged to the coal lock, moves by gravity flow into the generator and is continuously gasified by an oxygen-steam mixture introduced at the bottom of the gasifier. Molten slag is formed at the hearth and flows through a central taphole into a water quench bath. The slag-water slurry is periodically discharged from the slag lock. Process steam is generated and superheated in separately-fired, oil-burning units. Oxygen is supplied to the gasifier from a gas storage bank located some distance from the pilot plant. The capacity of the oxygen storage bank is about 130,000 standard cu ft at 2200 psig. Liquid oxygen is delivered by truck and is converted to gas during the filling operation. The superheated steam and oxygen are metered separately, then mixed and fed to the gasifier tuyeres. The gas generator is surrounded by a water jacket. The steam formed is separated in the steam drum and then discharged to the gas offtake, thus equaliz-

Jan 1, 1961

By N. Schapiro, R. J. Gray, G. D. Coe

A petrographic and chemical investigation was conducted to determine the occurrence and distribution of the organic and inorganic forms of sulfur in various size and specific gravity fractions of a high volatile, A-rank, Pittsburgh seam coal. The investigation was conducted to aid in the resolution of the problem of how metallurgical coke of lower sulfur content can be produced from high sulfur coals. The Pittsburgh raw coal contains about 2.4% S in two dominant forms: pyritic and organic. Pyritic sulfur constitutes about 57% of the total sulfur in the raw coal and occurs in macroscopic and microscopic-size particles. A plant cleaning process mechanically separates between 50 and 60% of the pyritic sulfur, mainly the macroscopic particles. The organic sulfur constitutes 41% of the total sulfur in the raw coal and 55% of the sulfur in the washed coal. Thus, organic sulfur is not reduced by physical methods of separation. Organic sulfur occurs in all the coal entities, but in general, increases as the exinoid content of the coal increases. In this study, it was found that carbonizing certain selected low gravity coal fractions containing an average of 0.45% pyritic sulfur and 1.01% organic sulfur produced cokes containing an average of 0.22% pyritic sulfur and 0.91% organic sulfur. However, the organic sulfur in the coke is probably derived in part from the heating of pyrite in the presence of carbon. Thus, the total sulfur in the coal carbonized is the most important factor affecting the sulfur content of the coke produced. Concentration of microscopic pyritic and organic sulfur in the middling-type coal indicates the necessity for rejecting as much of this material as is economically feasible. Most of the sulfur introduced into the blast furnace originates from the coke. Although the sulfur content of the hot metal can be controlled by the addition of flux, the flux used restricts the productivity of the furnace by displacing ore and requires first to be smelted; therefore, low sulfur coke is highly desirable. Since the sulfur content of coke is dependent upon the sulfur content of the coals from which the coke is produced, low sulfur coals are required to produce low sulfur coke. In the western Pennsylvania area, large quantities of good coking coal are available from the Pittsburgh seam, but this coal unfortunately contains relatively large quantities of sulfur. To provide information that might be useful in reducing the sulfur content of this coal in the cleaning process, an investigation was conducted to determine the physical and chemical forms in which this sulfur occurs and with what petrographic components it might be associated. The Pittsburgh seam coal, like most other coals, contains two dominant forms of sulfur: one occurs as the minerals pyrite and/or marcasite and is referred to as pyritic sulfur; the other is combined with the coal substance and is called organic sulfur. Pyritic sulfur is amenable to physical methods of separation, whereas organic sulfur is not. Pyritic sulfur particles must be freed from the surrounding coal if they are to be removed in the washing process. Generally, this requires crushing; the required degree of crushing being a function of the size and distribution of the pyrite. The present investigation was conducted to 1) determine the size, distribution and association of sulfur-bearing minerals in the coal and 2) to determine whether the organic sulfur has a preferential association with specific coal entities. If a preferential association exists, this knowledge may be useful in devising a method for organic sulfur reduction. In addition, a study was made to determine the extent to which pyritic and organic forms of sulfur in the coal contribute to the sulfur in the coke produced from this coal. A representative 3%-ton sample of raw coal was crushed to —3 in. and screened into square-mesh sizes: 3 to 1 in., 1 to % in., % to % in., % in. to 10 mesh, 10 to 35 mesh, and 35 to 200 mesh. Separate samples of the -200-mesh fraction and the all-size composite were also collected. Each size fraction (except the -200 mesh) was fractionated on heavy liquids of the following specific gravities: 1.280, 1.300, 1.325, 1.350, 1.375, 1.400, 1.425, 1.450,

Jan 1, 1963

By F. J. Chernosky

Most previous studies of coal flotation utilized chemically pure reagents. Since such reagents are not available in quantity, a study of various wmmercially available reagents as frothers was undertaken. Flotation procedures similar to those used in a large number of commercial coal flotation plants were employed. The reagents used were compared on yield-selectivity-wst basis. The selectivity was found to be relatively constant with yields above 70% but the reagent cost varied greatly. The types of reagents available were compared. In the past, a number of papers have been written on the use of various reagents as coal flotation frothers. For the most part, these have been an attempt to correlate the intrinsic chemical and physical proper- ties of the reagents or reagent groups to the floata-bility of various fine coals. Because of the type or nature of evaluations made, chemically pure reagents were normally used. Generally, these reagents are unavailable in commercial quantities. Therefore, the results obtained with these reagents were usually limited in usefulness to the plant operator or metallurgist. This paper presents the results of a study in which commercially available forms of various reagents were used as flotation frothers. Flotation procedures which would conform in general to those employed in a large number of commercial coal flotation plants were utilized. The objective of the test was to compare these reagents on yield-selectivity-cost basis, that is, 1) the yields obtained, 2) the ash levels obtained and 3) the reagent cost relating to these results. REAGENTS The reagents employed have been grouped into the following chemical classes: 1) aliphatic alcohols, 2) terpines, 3) glycols (synthetic water-soluble

Jan 1, 1963

By W. N. Poundstone, G. R. Spindler

A comprehensive report on extensive experimentation in degasification of the Pittsburgh Coal seam is presented. Detailed accounts of the procedures and results are given for permeability tests, vertical bore hole tests, measurement of gas flow from sealed drainage areas, horizontal rib hole tests, and water infusion tests. The removal of methane gas from coal seams in advance of mining is not a new idea with mining men—much attention has been given to the possibility for many years. In other parts of the world, a principal concern has been in the recovery and utilization of the gas and a number of successful projects have been developed in Europe and elsewhere. In this country, the principal motivation has been related to the safety aspect with some possible side benefits concerning costs and efficiency in mining as secondary objectives. To date, experimental work in this country has been largely or entirely exploratory to determine bed characteristics with respect to the liberation of combustible gases to investigate or establish the possibility of degasification in advance of mining and as an aid in projecting mine ventilation systems to provide for safe, effective and economical handling of combustible gases liberated during mining. With these objectives in mind, the School of Mines and Engineering Experiment Station at West Virginia University, in cooperation with the Christopher Coal Co. of Osage, W. Va., initiated some experimental work in May 1952 and the project has been more or less continuous since that time. The work has been centered entirely in mines of the cooperating company in Monongalia County, W. Va., and Greene County, Pa. LOCATION AND GENERAL CONDITIONS OF THE AREA The principal mining in the area involved is in the Pittsburgh coal seam which lies at the bottom of the Monongahela series of the Pennsylvanian. The Pittsburgh coal in the area is generally uniform in its structure and physical characteristics. The bed thickness averages about 7 to 8 ft and the coal has a characteristic blocky structure as the result of pronounced face cleats and definite, but somewhat less pronounced, butt cleavage. It is a medium volatile coal, averaging about 37 pct, and is marketed principally as a steam fuel and for metallurgical purposes. The Pittsburgh coal outcrops along the Monongahela River and dips gradually, but not uniformly, slightly north of west (about N75°W). The westward extensions of the bed, from the areas contiguous to the Monongahela River which have been heavily mined, constitute the principal reserves and are all well below drainage with the depth of cover increasing with the distance from the river. In general, with deeper cover, it may be expected that methane liberation will be more of a problem in future mining as compared to areas mined previously; therein lies the interest in possible de-gasification in advance of mining. Fig. 1 shows the Pittsburgh coal area in the vicinity of Morgantown in Monongalia County, W. Va., and Greene County, Pa., in which the experimental work discussed is located. Fig. 2 shows the contours on the Pittsburgh coal in the test area. It will be noted that the first two bore holes for the experiments were at the edge of a bench or terrace with considerable change in the gradient in the immediate vicinity of the test holes and that the same general condition applies to later test areas. Mining is intensively mechanized in the area and in the mines involved in the experimental work with corresponding rapid advance of working faces a typical characteristic. In the areas now mined the total methane liberation ranges from moderate to relatively heavy, but the actual face liberation is extremely variable and may range from practically

Jan 1, 1961

By A. M. Keenan, R. H. Carpenter

Geologic faults have always been a plague to the mining industry, and have often reduced a mining venture from a profitable to a marginal operation, and even at times have forced companies to liquidation or bankruptcy. The use of geology as an economic tool in coal mining is not generally recognized, particularly in coal deposits which are horizontal or essentially flat-lying, in which faulting might not be prevalent. However in pitching coal seams, the existence of faults is considered an inherent challenge, as the inclination of the seam or seams per se, is a product of geologic disturbance. The problems of faults are a constant challenge to the management of the Thompson Creek Coal and Coke Corp. in their operations in Pitkin County, Colorado, where high grade medium volatile coking coal is mined. The background for this paper has been provided by the experiences of these operations, in overcoming the effects of faults in mining, and resolving the fault structures. The properties of the Thompson Creek Coal and Coke Corp. are located in central Colorado, 13 miles southwest of Carbondale, Colorado, a tow] on the main highway between Glenwood Springs and Aspen, Fig. 1. The elevation at the mine portals is approximately 8000 feet: there is a relief of some 2.000 feet to the adjacent ridges rising away from the [nine portals. 'The entire present production of these properties totaling 180.000 tons of clean coal per year is trucked to the railhead at Carbondale, Colorado, from whence it is shipped to the Geneva Steel Plant at Provo, Utah. The properties were initially opened in September 1952. A total of 125 men are currently employed with the production conting from the Number 1 and 3 Mines, and development workings of the Number 2 and 5 Mines respectively. While the No. 2 Vine was opened in 1953 prior to No, 3 Mine, the encountering of faults without sufficient development work accomplished to sustain production, necessitated the diversion of manpower to the other [nines for economic considerations. GEOLOGY '1-he productive coal seams occur in the Mesaverde formation of Late Cretaceous age which outcrop along the eastern edge of the Piance Creek Basin from the Grand Hogback, a part of the southwestern flank of the White River Uplift north of Glenwood Springs, southward through the 'Thompson Creek area and the

Jan 1, 1961

By J. D. Allen

In the coal preparation plant at U.S. Steel Corp.'s Concord mine in Alabama, the product moisture was reduced from about 20% to 9% through the development of a workable flowsheet for dying the clean coal. Some of the high points of the conversion of the Concord washer from vibrating screen dewatering to centrifuge drying are presented in this article. The coal preparation plant at the United States Steel Corp.'s Concord mine near Bessemer, Ala., began operations in June, 1950. The basic cleaning circuit consisted of a Chance cone for cleaning the 2-in. x 3/8-in. fraction and concentrating tables for cleaning the -3/8-in. coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable with 85% passing 3 mesh and 25% passing 28 mesh (Fig. I), a considerable quantity of fines passed through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-ft-diam hyd rose para tors from which the underflow returned to the dewatering screens and the overflow went to a 175-ft-diam thickener for water clarification, as illustrated in Fig. 2. As might be expected, there was considerable recirculation of the -35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20%. Further reduction to approximately 11% was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a relatively small percentage of the over-all coal mix at the coke plant, its high moisture and fluctuations did not seriously hamper coking operations. Early in 1964, however, the proportion of Concord coal was increased with a resulting increase in the moisture of the total coal mix, and this caused difficulties in the coke plant. The increased participation of Concord coal also brought about a shortage of railroad cars which raised the moisture content to a point where the coal became almost impossible to handle. In an effort to alleviate this problem, U.S. Steel initiated a research program to develop a flowsheet for reducing the moisture to approximately 10% and to determine whether the resulting product would be satisfactory for the coke plant. Under this program, an experimental flowsheet for evaluating both a vibratory centrifuge system and a solid bowl centrifuge system was drawn up as shown in Fig. 3. A horizontal vibratory centrifuge was installed to reduce the moisture in the dewatered coarse coal, and a four-cell, flotation machine was installed to clean the -65-mesh portion of the 3/8-in. x 0 table raw coal feed. Several shortcomings in the above circuits were apparent. For one thing, large quantities of repulping water were required. Furthermore, since about half of the flotation feed was of a size consist that could have been cleaned on the tables, these circuits would result in an unnecessary increase in reagent costs and facilities. Maintenance of the hydro separators and pumps for pumping the underflow to the filters,

Jan 1, 1969

By Shiou-Chuan Sun

DISCUSSION shiou-chuan sun (author's correction) - Too late for revision, the author realized that the data on stability of froth presented in this paper were not based on the same height of froth column. It is recommended herein that the stability of froth is better calculated by dividing the time elapsed until the froth disappeared by the volume (in cu cm per sq cm) or height of the froth column, and is expressed in sec per cm. The stability data in Tables I, II, and III of this paper were recalculated, in accordance with this recommendation, and the results are shown respectively in the accompanying Tables VII, VIII, and IX. Compared with Tables I, II, and III of the paper, the stability data of Tables VII, VIII, and IX are more reliable in disclosing the persistence of froth of various frothers having different frothabilities. For example, the conclusion given in the paper that the stability of froth is generally proportional to the volume of froth becomes invalid when the stability of froth is expressed in sec per cm, as shown in Tables VII, VIII, and IX. Table VII shows that both the stability and volume of froth increase with the addition of small amounts of n-hexyl alcohol, and that further additions of n-hexyl alcohol decrease the stability but increase the volume of froth. Table VIII indicates that the stability of different types of frothers is governed by their chemical composition and is difficult to predict from their frothability. Table IX shows that the stability of different frothers with similar nonpolar groups tends to increase with a decrease of the hydro- philic property of their polar groups, and consequently with the decrease of their solubilities. This is further substantiated by the fact that the stability of frothers, as listed in Table IX, is generally lowered by the solvent effect of absolute ethyl alcohol. Table IX shows also that the stability of froth tends to increase with the decrease of the volume of froth* provided the frothers used have similar nonpolar groups and dissimilar polar groups.

Jan 1, 1953