Search Documents

By J. -G. Swanson

Dust control in longwall coal mining depends primarily on the prevention of dust at the source and secondarily on the suppression of airborne dust. One of the primary methods for the prevention of dust is the wetting of the coal face prior to extraction, which can be achieved with water spray systems installed on the shield supports. The spray droplets must travel across the airway to the longwall face, where high ventilation air speeds can entrain water droplets and prevent them from reaching the face thus minimizing the dust control at the source. Through an evaluation of spray plume characteristics in a wind tunnel, the droplet size and droplet drift behavior was determined. This drift behavior was examined by evaluating the spray plume concentration drop and the droplet size shift near the nozzle exit at varying air speeds. Based on these evaluations, CFD modeling was applied to simulate the spray behavior for varying geometries. These results led to the selection of appropriate spray nozzles capable of carrying water droplets to the face at higher air speeds, resulting in an adequate wetting of the coal face and reduced dust generation.

Jan 1, 2012

By Yves Caron

Résumédes travaux effectués De septembre 2009 àmai 2011 ? Plus de 21 000 m de forages complétés en avril 2011 et près de 9 000 échantillons ? 2,7 km de décapage, 52 tranchées et 852 m de rainures ? Estiméde ressources 28 mai 2010 (SGS Géostat) ? Essais métallurgiques en laboratoire (automne 2010) ? Étude économique préliminaire (janvier 2011)

May 1, 2011

By Z. Y. Ding

This paper emphasize two points in piled wharf design which are important than structure calculation. First, during design of piled wharf on soft stratum, the bank slope stability is the first important item. Second, the live load, the backfill and the original ground's settlement will influence the wharf structure causes cracks. Two practical examples were illustrated.

Jan 1, 1991

Port Gaspé is located on the back side of Gaspé bay and is protected by a natural sand barrier with a length of 2,5 km, from which it got its name, Gaspé Sandy Beach (1). Since 1904 the Gaspé region had a deep water wharf, initially very different, in fact, from the one existing just before the recent reconstruction (2). This wharf with a length of 228 m and a width of 23 m was build of timber cribs. The outside walls of these cribs had been doubled with a wooden wall, creosote impregnated to provide resistance to decay and to the attack of marine organisms (limnorias) (3). Fifteen years ago the upper part of the wood construction had to be removed, because of progressing rottenness and was replaced by an L-shaped reinforced concrete structure (4).

Jan 1, 1987

By Jerry Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (1 l- 14 million cubic meters) of gas per day.

Jan 1, 1996

By Costa

The fly-in-fly-out (FIFO) mining model has significant implications for the industry as it plays an important role in fulfilling the economic, social and workforce needs of the contemporary mining industry. It has increasingly been adopted in countries such as Canada and Australia, but is the current nature of the FIFO model challenging the place women have achieved in the mining workforce? Research in the mining and oil and gas industries reveals that major sources of stress for fly-in-fly-out mining workers are the times of parting and of reunion, the challenges in defining roles within the family, parenting, and conflict between spouses over the use of the leave time and money. So how are women in the industry coping with the FIFO schedules and consequent intermittent relationship with families and partners? How is the mining industry adapting to recruit and maintain female employees in FIFO operations? This paper describes an exploratory study conducted in Canada, which intended to provide some initial insights that might help us answer the questions above. There are several inferences made from this exploratory study. It is clear that FIFO poses significant challenges for both female and male workers. It is largely seen as rigid, extremely challenging for employees with young families and workers who are single mothers, and it is generally incompatible with starting a family and caring for small children. FIFO creates severe stress on relationships and on workers psychological well-being. It seems to be indeed harder for women, since they are often in lower paying positions and therefore have less financial reward for the FIFO lifestyle. On the other hand, FIFO creates the opportunity for young women, including Aboriginal women, to jump-start their careers, as well as opportunities for mature women to work while pursuing other personal interests during their time off. This paper concludes with recommendations to improve the FIFO system in order to increase the ability of mining companies to hire and retain women

May 1, 2006

By B. Amadei, F. Tonon

Rock stress measurement is cast in the more general context of the determination of boundary conditions for rock engineering. A study on the effect of elastic anisotropy on underground excavations reveals that this effect is actually controlled by the imposed boundary conditions. Applications to tunneling and to the Underground Research Laboratory (URL), Canada, exemplify a procedure for boundary condition estimation formerly developed by the authors. The procedure displayed fast convergence despite the complex geometry, and the high degree of non-linearity of the models. In the URL application, the 3-D model was able to completely reproduce the complex measured stress pattern, and the 90° rotation of the principal in situ stresses with depth. In order to reliably estimate the boundary conditions reproducing the current in situ state of stress, response measurements of the rock mass to current disturbances are necessary as input data. La mesure des contraintes in situ tombe dans le domaine général de la détermination des conditions aux limites pour les problèmes de mécanique des roches. Une étude sur le rôle de l’anisotropie élastique sur les excavations souterraines montre que ce rôle est contrôlé par les conditions aux limites qui sont imposées. L’application aux tunnels et au Laboratoire Souterrain de Recherche (URL) au Canada, nous permet de présenter une méthode de détermination des conditions aux limites. La méthode converge rapidement bien que le géométrie soit complexe et que le problème soit non-linéaire. Pour le URL, le modèle 3D est capable de reproduire la distribution des contraintes qui ont été mesurées ainsi que la rotation de 90 degrés des contraintes in situ avec la profondeur. Afin de déterminer avec précision les conditions aux limites responsables pour la distribution actuelle des contraintes, la réponse du massif rocheux doit être connue et mesurée. In der Felsentechnik sind die Spannungsmessungen in Gestein an die Bestimmung der Randbedingungen gebunden. Eine Studie legt dar, dass der Effekt elastischer Anisotropie in unterirdischen Aushoehlungen von den Randbedingungen kontrolliert ist. Eine von den Authoren entwickelte Methode zur Bestimmung der Randbedingungen wird an Beispielen im Tunnelbau und im Underground Research Laboratory (URL) in Kanada illustriert. Auch bei komplexer Geometrie und einem hohen Grad an Nicht-Linearitaet zeigt diese Methode ein schnelles Konvergenzverhalten. Ein 3D-Model und dessen 90° Drehung der lokalen Hauptspannungen mit der Tiefe, kann bei einer URL Anwendung vollstaendig reproduziert werden. Um mit dieser Methode die Randbedingungen zuverlaessig abschaetzen zu koennen, werden der gegenwaertige lokale Spannungszustand sowie die Antwort des Gesteins und die resultierenden Stoerungen als Eingabedaten benoetigt.

Jan 1, 2003

By P Staples, G Lane, S Morrell

The design of semi-autogenous grinding (SAG) mill based comminution circuits for the treatment of competent ores, similar to those at Geita and Boddington, involves the same process of sample selection, test work, data analysis and data modelling/interpretation as that used for 'average' competency ores. However, over the past couple of years a number of issues have arisen that are common to the design of circuits for the comminution of 'highly' competent ores. The impact of these issues on project viability is generally more pronounced when treating hard ores than average to soft ores due to the greater impact on capital and operating costs. The issues encountered have included: standard test procedures have been modified; test equipment has worn or been damaged; different procedures yield different data and varying interpretation; and modelling and empirical calculations have been based on poor benchmarks, or used incorrectly in the case of JKSimMet, yielding misleading outcomes. The purpose of this paper is to present, discuss and clarify some of the issues associated with conducting test work and designing comminution circuits for the treatment of 'highly' competent ores in order to reduce thelevel of conflict arising from interpretation and application of test work data. Specifically, the issues associated with the bond crushing (impact) and rod work indices measurement, the various SAG mill specific energy tests, and the interpretation of the resulting data will be discussed in the context of case studies.

Jan 1, 2009

By George G. Goble

In the middle of the nineteenth century, the dynamic formula appeared as a description of pile penetration during impact driving. The simplicity of use of the formula combined with the power of the energy concepts behind the formula caused it to be quickly accepted and integrated into practice. Dynamic formula had been in use for 100 years when the Wave Equation computer programs first appeared. With that long experience it is not surprising that the formula continued to be used and were only slowly abandoned. The Wave Equation offers many advantages over the various formula but it does not offer a clear sense of physical understanding of pile driving that is available with the formula. Large amounts of numbers are generated but often it is difficult or impossible to gain a physical understanding of the results or a feeling for the importance of the various parameters. The question that the Wave Equation user has is, "What will happen if I use a larger drive cap (or change any other item of equipment)?" In this paper, I will attempt to explain pile driving using elementary wave propagation theory. However, the presentation will not depend on any higher mathematics. With the use of wave mechanics, it is possible to explain driving characteristics that cannot be handled with the energy formula.

Jan 1, 1995

A clear understanding of the meanings of terms is important when discussing a project. Whether it is a submission, an investment study, a feasibility study, an environmental impact statement, an estimate, a tender, a contract, or a close-out.report, the need for all parties involved to understand what is under discussion or what has been written is paramount. The clarity of definition and the level of understanding can affect the outcome of the project. It is vital that all parties know what is wanted, what is expected, and what it will cost. This paper draws attention to some of the problems that beset many projects, clients, project managers and contractors, and it is hoped that its presentation will encourage us to pay more attention to defining what it is that is required. Ultimately we should all be the richer for having defined and understood the requirements at the beginning rather than at the end.

Jan 1, 1990

By Robert Bosworth

THE liability for damages to the surface caused by subsidence is an ever present threat in all underground mining. In ordinary lode mining, this threat rarely materializes into an action, due to the method of mining metalliferous ores, the dip of the veins, and the nature of the ground itself. In the mining of coal, however, this threat is very real. The coal frequently lies close to the surface, in beds underlying large areas of land of which the surface is suitable for agricultural or urban development. Furthermore, the coal is generally mined by the "room and pillar " method and when the pillars of coal are removed, the subjacent support is destroyed. This question of the duty of surface support has now become a very live one in Colorado. What was waste prairie land a few years ago has become valuable agricultural land dotted here and there with growing towns. Frequent references will be made here to Colorado conditions and adjudicated cases, but those conditions and cases and the conclusions to be drawn therefrom are applicable to all coal-mining states. Briefly stated, the question is "Does the owner of the substrata or underlying mineral owe any duty of surface support to the owner of the superjacent strata or surface?" There is no absolute duty of support owed by the mineral owner and this assertion is made with full knowledge of numerous expressions to the contrary by courts of Pennsylvania, Illinois, Colorado and other coal-mining states. Whether or not any duty exists depends upon the circumstances surrounding each case, and since in the nature of things those circumstances are rarely identical, there can be no absolute rule.

Jan 1, 1928

By Robert Bosworth

THE liability for damages to the surface caused by subsidence is an ever present threat in all underground mining. In ordinary lode mining, this threat rarely materializes into an action, due to the method of mining metalliferous ores, the dip of the veins, and the nature of the ground itself. In the mining of coal, however, this threat is very real. The coal frequently lies close to the surface, in beds underlying large areas of land of which the surface is suitable for: agricultural or urban development. Furthermore, the coal is generally mined by the "room and pillar" method and when the pillars of coal are removed, the subjacent support is destroyed. This question of the duty of surface support has now become a very live one in Colorado. What was waste prairie land a few years ago has become valuable agricultural land dotted here and there with growing towns. Frequent references will' be made here to Colorado conditions and adjudicated cases, but those conditions and cases and the conclusions to be drawn therefrom are applicable to all coal-mining states. Briefly stated, the question is "Does the owner of the substrata or underlying mineral owe any duty of surface support to the owner of the superjacent strata or surface?" There is no absolute duty of support owed by the mineral owner and this assertion is made with full knowledge of numerous expressions to the contrary by courts of Pennsylvania, Illinois, Colorado and other coal-mining states. Whether or not any duty exists depends upon the circumstances surrounding each case, and since in the nature of things those circumstances are rarely identical, there can be no absolute rule.

Jan 1, 1928

Distinguished guests ladies and Gentlemen. As many of you know, before I became a Labour Member of Parliament, I had an unusual career path for a politician, in that I spent quite a few years working in the business community. In other words, I was mainstreamed before I was institutionalised. Given that some of this time was spent working for the then Macraes Mining Company Limited, now Gold and Resource Developments NL, I feel that I may have a perspective on how things are seen, on both sides of the fence. In terms of public perception and esteem I am not sure which career option was the step up and which was the step down. So far what I have found very familiar, is that in both roles there is a gulf between the reality and the perception of that reality - a gulf that is both huge and hard to bridge. I think it is a point worth making here amongst another busy industry cluster, that we can all too easily get so embroiled in the day to day activities, that we lose sight of how this might look to those running on a different treadmill. I can still remember scratching my head at the beginning of some days, as I worked to get new mining projects started that I knew were going to bring real jobs and economic benefit to New Zealand, but ending the day feeling like I may instead have been proposing bringing back both strip mining and slavery. If I learnt one valuable lesson out of that time it was this: .... mining has become so publicly demonised on the road to ecological nirvana, that even attempting a lucid dialogue on mining issues, with some, is incredibly difficult.

Jan 1, 2000

By Don Simon

In the late 1960s the mining industry was in an apparent slump due to a combination of factors. Enrollment dropped significantly at schools offering mining engineering degrees, resulting in a shortage today of experienced mining graduates to staff middle management positions. How has this limited supply affected salaries? Does the shortage impair the mining industry's ability to respond to national energy needs?

Jan 12, 1979

By P. J. N. Pells

A good thing is becoming a bad thing. Rock mass classification systems, that are so excellent for communications between engineers and geologists, and that can be valuable in categorizing project experience, are emasculating engineering geology and rock mechanics. Some engineering geologists have been sucked into thinking that Q and RMR values are all that is needed for engineering purposes, and seem to have put aside what can be learned from structural geology and geomorphology. Many rock mechanics engineers seem to have forgotten the scientific method. This paper attempts to redress the situation by showing how mechanics can be used in rock engineering to design with a similar rigour to that used in the fields of structural engineering, hydraulics and soil mechanics. It also attempts to remind practitioners of what can be achieved by skilled engineering geology.

Jan 1, 2008

Answers to many questions arising in the different phases of exploration, estimation and production of a mineral deposit, can be found in the geostatistical theory of G. Matheron. It is shown that all these questions regarding sample size, number of samples, shape of drilling pattern can be answered as soon as the continuity of the mineralization is quantitatively characterized by means of a variogram. Next a formula which gives the variance of the error associated to any estimation procedure (i.e., any method and any sampling pattern) is given. Applications to the computation of the standard error of the'mean for various sampling patterns are shown, as well as how to use the formula to simulate several possible sampling strategies and choose the best one. Altogether it is shown how to answer the often heard question, "what happens if such and such sampling procedure is used?", rather than giving an hypothetical "optimal" solution.

Jan 1, 1976

By Ann L. Backstrom

The Apex Tunnel is part of the Southern Nevada Water Authority?s proposed Clark, Lincoln, and White Pine Counties Groundwater Development Project. The project is intended to develop unused Nevada groundwater for meeting the water needs of Southern Nevada and would involve over 322 km (200 mi) of water transmission facilities. The Apex Tunnel, as currently conceived by ongoing planning and environmental analyses, would extend 2804 m (9,200 ft) through a structurally complex terrain of Paleozoic carbonate rocks and younger basin fill deposits and will traverse both public and private lands. Several faults cross the tunnel study area, juxtaposing rocks of varying lithology and degree of folding, and creating intervals of differing rock conditions along the tunnel alignment. This paper discusses how the geotechnical program was developed to be flexible and allow for rapid implementation of revisions based on new knowledge that became available during program execution, resulting in more effective decision making and enhanced value from the geologic investigation during the planning phase of the project.

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By I. Jones

Geologists, engineers, technicians and surveyors have successfully utilized technical software in the mining industry for over 30 years. Software for processing survey, geology, mine engineering and planning information make these functions more efficient by automating repetitive tasks and reducing data processing errors. While these systems have been improved incrementally overtime, new systems that represent giant leaps in technology have been introduced to help mining operations increase productivity and reduce costs. However, their widespread use within the industry has left individual companies without a competitive advantage. Additionally, the ability of these applications to provide the productivity improvements required in today’s uncertain market conditions has since peaked. The next wave of technology—integration of independent software applications—is just starting to emerge and will have a significant effect on the productivity of mining operations. To reap the productivity gains required to remain competitive, mining companies must exploit the collective knowledge and experience of every employee in the organization. Integration of independent software application allows companies to leverage information from all activities, enabling staff to make better decisions to improve productivity. This paper outlines the importance of integration as productivity enabler. Key performance indicators, strategic mine planning, resources management and mine-to-mill integration are discussed as processes that enable productivity. The Gemcom Enterprise Mining System (GEMS)is introduced as the industry’s first integrated solution that enables these productive processes. The paper concludes with a comment on the level of change required to realize the benefits of integration.

Jan 1, 2003

Miners and explorers in New Zealand are expected to consult with stakeholders, keep out of core conservation areas, and operate a high standard of environmental management and rehabilitation. These requirements are not difficult to meet, but many of the industry's own actions have brought it to a low level of general public esteem in New Zealand. Reasons for this are discussed, drawing examples from the Maruia Society's experiences with the industry since the mid-1980s. The boundary between core conservation areas and other land is not easily drawn, and the Maruia Society has sought to work with the mining industry to promote legislation for net conservation benefit trade-offs. However this initiative was not successful. Today the industry, unlike most other major industry sectors in New Zealand, has no accord with the country's conservation movement.

Jan 1, 1997