Search Documents

Mining education has received almost continuous discussion since its inception and most people engaged in the mining industry and in mining education feel at some time the urge and necessity to express their views. This paper is not a comprehensive survey of past and present practices and accepted principles, but a personal opinion of the form mining education should take at university level. It is expressed because of a dissatisfaction with the existing courses offered to students. It is hoped to provoke discussionand bring forth guidance to those engaged in mining education. After all, students spend four or five years at a university and it is desirable that the graduate should be something more than just those many years older at the end of his course.POST GRADUATE EMPLOYMENTThe first problem confronting the university should, be to discover what the mining industry wants and expects or graduates. This must influence the university course and yet universities have done little to seek this information, and if suggestions have been offered by industry; universities appear to have made little use of them. University mining curricula are basically what they were 50, 100 and even 200 years ago. (See Appendix.) Whether this reflects the unchanging problems of mining the wisdom of early professors, the conservatism of subsequent professors or inability to apprectate necessity for changes, is debatable.Unfortunately there is no uniformity in the type of employment offered to new graduates: Some mining...

Jan 1, 1959

By Lawrie Logan, Mike Wiggin

This paper will be in two parts, a discussion of the benefits available from benefit sharing as a concept followed by an examination of how this approach was applied at Mesa J Mine and what improvements were made. The first part is an outline of the ways that both parties in a benefit sharing agreement can uncover additional wealth by bringing a new approach to the relationships between mine and supplier. The paper describes a partnering agreement recently established between Robe River Iron Associates (RRIA) and Dyno Nobel Asia Pacific Ltd (DNAP) to access the wealth locked up by the usual explosives supply contracts in Australia and elsewhere. The partners are acting cooperatively to maximise the benefits to both parties from optimising blasting practices at the Mesa J Iron Ore Mine in the Pilbara region of Western Australia.

Jan 1, 2001

By P. Tolvanen, A. Jalili

"When hard times strike in the mining cycle, sites tighten their belts and focus on lowering their unit costs. Lower unit costs can be achieved by reducing expenditure, increasing production, or by a combination of both. Faced with these requirements, site personnel must turn to areas where they can focus their effort for maximum return. For many sites, both in Canada and overseas, focusing on improving flotation cell maintenance is one of the areas where gains can be made for minimum outlay. Due to resource limitations and/or lack of equipment understanding, maintenance on many sites is only conducted on a reactive basis, once equipment fails. This paper will promote the idea that mineral processors should become more familiar with their equipment so they can ensure that the plant’s ability to produce is not compromised. By better understanding the flotation equipment and ensuring the critical components are maintained, it should be possible to unlock value in an operation. Flotation equipment inspections will be discussed in detail, including key items to look for during these inspections. Potential approaches for predicting wear and change-out time for flotation equipment components will be also demonstrated. An example of one approach used at a South African nickel site will be given.INTRODUCTIONWith metal prices decreasing and operating costs rising, concentrator operators are looking for ways to improve their bottom line. Lower unit costs can be achieved by reducing expenditure, increasing production, or by a combination of both. To meet the expectation of shareholders, mineral processors must turn to areas where they can get the best return for their efforts. One area where there is a large opportunity for improvement is in the maintenance of flotation equipment.On many mine sites, both domestically and around the world, it is quite common to see the philosophy applied of repairing equipment only once it has failed. Though some sites have advanced enterprise management systems and monitoring programs, in the authors’ experience, the decision on flotation equipment maintenance is rarely made on a proactive basis. Two common trends that are evident in the mining industry are that operations are under pressure to keep the plant producing, and maintenance managers generally have very strict budget targets to meet. In addition to these factors, few sites have a good understanding of the financial implications of running with worn or broken flotation equipment. Knights, Jullian and Jofre (2006) summarize this situation well, stating that the lack of correlation between some commonly used maintenance performance measures and key business drivers can lead to maintenance being seen only as a cost center (that needs to be reduced) rather than a tool for productivity improvement."

Jan 1, 2015

By Lon Santis, Dale Ramsey

The use of aircraft to support blasting operations in mines, quarries and construction sites goes back to the early days of aviation. Invaluable at times, aircraft use has been limited by cost, the unpredictability of weather impacts and other factors. Recently several technologies have matured to open up a new way to acquire aerial data with unmanned aircraft systems (UAS), commonly called drones. Equally important, the U.S. Federal Aviation Administration has recently implemented an exemption process and rulemaking to implement the commercial use of UAS into the United States’ National Airspace. The skies are opening for many applications of UAS. The most notable may be photogrammetry, which is the science of making measurements from photographs, especially for determining the exact positions of surface points.

Jan 1, 2016

By D. H. McCain

Through a unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT) Center, a video packed, dazzling CD-ROM training program was developed for new miners entering the aggregate industry. Why this product was developed, and why the aggregate industry, will be discussed along with the challenges faced throughout the project. Cooperation from every one involved including MSHA made this the product of which all other training materials in the mining industry will be measured against in the 21st Century. This product's versatility and wide application makes it a tool that is as critical to a mine's success as any earth moving machine. Developed with both state and federal grant moneys allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2001

By H. Jang, Y. Kawamura

Unplanned dilution and ore loss directly influence not only the productivity of underground stopes, but also the profitability of the entire mining process. Stope dilution is a result of complex interactions between a number of factors, and cannot be predicted prior to mining. In this study, unplanned dilution and ore loss prediction models were established using multiple linear and nonlinear regression analysis (MLRA and MNRA), as well as an artificial neural network (ANN) method based on 1067 datasets with ten causative factors from three underground longhole stoping mines in Western Australia. Models were established for individual mines, as well as a general model that includes all of the mine data-sets. The correlation coefficient (R) was used to evaluate the methods, and the values for MLRA, MNRA, and ANN compared with the general model were 0.419, 0.438, and 0.719, respectively. Considering that the current unplanned dilution and ore loss prediction for the mines investigated yielded an R of 0.088, the ANN model results are noteworthy. The proposed ANN model can be used directly as a practical tool to predict unplanned dilution and ore loss in mines, which will not only enhance productivity, but will also be beneficial for stope planning and design.

Jan 1, 2015

By C. H. Jr. Herty

DURING the past few years frequent reference has been made to a certain type of iron known generally as "bad iron," "dirty iron," etc., both by steelmakers and producers of iron castings.1 Open-hearth operators have claimed that such iron was entirely within the specified limits as to ordinary analysis but it was difficult to make good steel from it. It has been suggested that unreduced material in the iron is responsible, also that most trouble is experienced with the iron when the blast furnace is delivering a product whose analysis is more or less variable. Other reasons suggested are the use of scrap or borings, unsintered flue dust in the burden, a cold hearth, too high a proportion of unsuitable grade of ore, or the form of the carbon in the iron. Accordingly, a subcommittee was appointed at the fall meeting of the Open-hearth Committee of the American Institute of Mining and Metallurgical Engineers held in Pittsburgh in October, 1926, to investigate the reasons for the occurrence of this bad iron and suggest methods for preventing its appearance. This committee enlisted the cooperation of the U. S: Bureau of Mines Experiment Station at Pittsburgh in undertaking a study of pig-iron quality as affecting the open hearth. The following is a report of the findings to date:

Jan 1, 1929

By Tsunehisa Nishimura

Stable operation of the blast furnace needs adequate control of the lower part. To clarify the behavior of the lower part of the blast furnace with accurate consideration of the property of slag and its flow characteristic, a new mathematical model has been developed. Using this model, the effects of the change of operational conditions on the behavior of the lower part of the blast furnace were studied. Further, means to control of the lower part of the blast furnace, especially effective means to maintain adequate temperature, were discussed. And desirable slag property and composition, especially the method to control FeO concentration dripping from the bottom of the cohesive zone to avoid a decrease in temperature of the lower part of the blast furnace was estimated.

Jan 1, 2006

By Andrew L. Peterson

CATOH Inc. of Weedsport, New York recently completed a very challenging Bored-In Pile project which features unique construction techniques in the installation and load testing of 45 and 100 ton capacity piles. The bored-in piles were installed on a twenty-nine million dollar New York State Department of Transportation project which began in the fall of 1995 and ended in March of 1997. The project included the construction of 5 new bridges to alleviate a very congested traffic network which had come to be known as the "Octopus" in the small city of Ithaca, New York. CATOH Inc. was awarded the piling contract by general contractor Santaro Industries in the fall of 1995. Piling installation work was completed in March of 1997. BACKGROUND The project is located at the southern tip of Cayuga Lake which lies in the heart of Upstate New York's Finger Lakes Region. This region is popular not only for wine making and vacationing, but also for its impressive geological history. The glacial activities that helped to form the deep valleys of this scenic area are also responsible for creating challenging underground conditions for deep foundations work. CATOH developed two pile designs to accommodate differing site conditions on the project. Internally reinforced piles were developed for use in the center of the valley and externally reinforced piles were developed for locations close to the valley wall.

Jan 1, 1997

By C. T. Christensen

The paper gives an outline of the design, installation and performance of a series of mooring and berthing dolphins for a major ferry berth outside the port of Elsinore, Denmark. The Dolphins are large cylindrical bottle shaped and open ended steel piles vibrated into the sandy seabed. They are subsequently equipped with prefabricated fender units. Vehicle access to the ferry is via a fixed ramp and a semi-submerged linkspan. Supplementary passenger access is via a covered gangway steel bridge from an existing gangway facility to a midship door in the ferry«

Jan 1, 1989

By Larry Rayburn

Design of cost effective engineered solutions to complex problems requires the team efforts of the owner, the designer and the specialty construction contractor. The basic ingredients of success required to remain competitive and still produce a quality product are creative design based on experience and sound engineering principles, plus practical aspects of constructibility. The three case histories describe creative design/construct approaches that benefited all parties. 1. Introduction The increasing demand placed on specialty contractors to provide cost effective buildable solutions to complex construction problems compels us in the industry to be highly innovative. The practice of geotechnical engineering is considered more of an "art" than perhaps the other disciplines within civil engineering largely because of the basic nature and variability of soil and rock. The geotechnical design engineer must have the knowledge of the components of his design and know the limitations of his equipment and labor force. Thus, for the design/build specialty contractor the potential for creation of unusual solutions to difficult problems is quite high.

Jan 1, 1991

By Adams F. C, Ridley K. L

Economic conditions after WorId War II made the recovery of Australian sources of sulphur one of considerable national importance. From 1947 to 1949 an investigation was made of recirculation techniques to produce acid plant grade gas from the Dwight-Lloyd down-draught sintering plant.During 1949 it appeared feasible to produce a gas of suitable 802 concentration and a decision was made to construct a gas purification train and a 150 tons/day contact acid plant. However, a number of difficulties remained in the production of the gases for sulphuric acid manufacture and as a result of research conducted to overcome these troubles the continuous up-draught sintering process was developed.The principal difficulties were:(a:) The down-draught sintering practice, as developed, produced an unusually high metallic lead precipitation in the windboxes. The disposal of this lead interrupted sintering operations and the delivery of gas to the acid plant.(b) The production capacity of the existing sintering plant was fully extended and the adoption of recirculation of gases, in an endeavour to satisfy acid plant requirements, would probably reduce the plant production capacity.(c) The prevailing high temperature of water available for purification train cooling required a higher than...

Jan 1, 1956

By Georgios Kalamaras, Chiaia Dinu, Platania Paolo, Alessio Carlo, Giampiero Cirvegna, Claudio Santucci

The Project alignment initiates north of Pinerolo, along the State Road 23[S.S. 23] that is one of the principal arteries to the northwestern Alps where a number of Olympic events for the 2006 Winter Games will be held. The 3.5 km ring road bypasses the Porte habitat by traversing twice the Chisone River. It consists of the following principal structures [Figure 1]: San Martino bridge [130 m in four bays] Prarostino viaduct [130 m in four bays] Craviale tunnel [1055 m] Turinella bridge [a 50 m long bridge that connects the two tunnels] Turina tunnel [665 m] Malanaggio viaduct [350 m in 9 bays]. The road section is 13 m wide and is made up of two 3.75 m lanes, a hard shoulder [1.50 m wide] and a 1.25 m wide curb for each lane. The Project maximum velocity is 100 km/h.

Jan 1, 2005

By Charles L. Kimbell

World political events that occurred subsequent to yearend 1990, but that bear heavily on the global mineral industry, have been of such importance that they cannot be disregaded, and certainly they contribute to any type of "outlook." However, to write of them simply as "forecasts" in an "outlook" section of this study would be to unjustly pretend to status as prophets. Thus, this section covers events that have occurred not as predictions but rather as history. Despite the end of the cold war, the world remained fractionated, at least from the limited perspective of its mineral industry. The fractionation was not so much the result of adversarial politics between countries and groups of countries, although to be sure, such conflicts had not disappeared. Rather, the fractionation was in the widely divergent patterns of performance that resulted from the diverse conditions and problems facing the different countries and country groups.

Jan 1, 1993

This work shall consist of furnishing and driving foundation piles of the type and dimensions designated on the plans or in the special provisions including cutting off or building up foundation piles when required. This specification also covers providing test piles and performing loading tests. Piling shall conform to and be installed in accordance with these specifications, and at the location, and to the elevation, penetration and bearing capacity shown on the plans or as directed by the Engineer. Except when test piles are required, the Contractor shall furnish the piles in accordance with the dimensions shown on the plans or special provisions. When test piles are required, the pile lengths shown on the plans are for estimating purposes only and the actual lengths to be furnished for production piles will be determined by the Engineer after the test piles have been driven. The lengths given in the Engineer's order list will include only the lengths anticipated for use in the completed structure. The Contractor shall, with-out added compensation, increase the lengths shown or ordered to provide for fresh heading and for such additional length as may be necessary to suit his method of operation.

Jan 1, 1989

By C. Cornejo, C. Schuffeneger, J. Rosas

"At the end of 2010 the AMSA Esperanza Concentrator started commissioning. Located in the Atacama Desert this project is the first of several large size concentrators developed recently to operate in Northern Chile. In addition to the new operations to be implemented in the short term, many existing installations are planning expansions. The use of large size equipment is one of the common characteristics of the new concentrators, but also new technologies are being considered and innovation is present in most cases. Sea water or desalinated water will be required to process large tonnages of sulphide copper ores as well as gold bearing ores, since process water supply from the Andes will no longer be available. The high cost of sea water or desalinated water supply and the high cost of energy are not a limitation as the current metal market scenario allows obtaining an attractive NPV even from installations designed to process relatively low grade ores. A review of the current concentrators being developed in Chile is presented, including a description of the main design issues related to technology and innovation. An analysis of the Chilean mining industry is also presented, detailing mine and plant capacities as well as expected final products.INTRODUCTION The mining sector in Chile has become a reference when analysing the large concentrator plants projected or currently in operation all over the world. At present and as a consequence of the high price of metal commodities, most South American countries have an active mining sector. Chile is known as a major producer of metals. First records of copper production exported to Spain are dated to the early XVII century. Since then Chile has produced over 13% of the total copper ever produced in the world. After 1990 Chilean mining and the associated cluster of activities has substantially grown to levels never reached before, especially in the production of copper, gold and other non-metallic minerals. This dramatic increase is the result of an economic policy based on delivering comparative advantages and incentives for the admission of foreign capital to offset the weak domestic investment in previous decades. Massive mining of its huge mineral resources has allowed Chile to be a world leader in the production of copper and other base metals and mineral products."

Jan 1, 2012

By Andrea M. Ouchi

A major focus of ground control research presently being conducted by the Geomechanics Group in the University of British Columbia Mining Engineering Department is to incorporate weak rock masses (RMR76 less than 50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented by mapping of one mine in Montana and of several mines within the Carlin and Getchell Trends of Nevada. In addition, a neural network analysis has been performed and modifications of the span design curves at the lower RMR76 range have been made. The common factor in all the above mentioned mines is a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be dealt with to safely extract the mineral bearing rock. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

May 1, 2004

By L. Frederick

Measurement of gamma radiation occurring in nature to characterize geological formations has been widely recognized in mineral exploration. Different methods and apparatuses have been developed for drill hole logging purposes. Geological formations vary in amount of naturally emitted gamma radiation. A gamma signature from a geological formation is captured by utilizing different types of gamma detectors. A natural gamma radiation detector (NGRD) can be used to control mining whenever there is a significant difference between the radiation levels in the mineral or ore being mined and the waste materials surrounding the ore. Surface miners, such as the one shown in Figure 1, can precisely control the elevation of the cutter as the machine moves over the surface of the formation. This type of machine is predominantly used in selective mining operations, e.g. surface coal mining. If there is a means to know the position of the cutter relative to the interface between the ore and waste, the miner can recover all or most all of the valuable mineral with very little out-of-seam dilution. This paper discusses the results of a successful application of gamma detectors to control a surface miner at one of North American Coal Corporations? locations - Red Hills Mine. The mine has nine coal seams in total with thicknesses ranging from 12? to 60?. The bottom six seams (Figure 2) are minable. The mine has complex geology and a significant amount of annual rainfall (4.7 ft). The mine produces approximately 3.5 million tons of coal and about 40 bcy of overburden per year. The operation utilizes diverse mining equipment including Dragline Marion 8200, electric shovel P&H 2800, Caterpillar end dump trucks CAT 785 and 789; bulldozers CAT D11, D10, D8, and D6. Coal is mainly extracted by utilizing a Wirtgen SM 4200 surface miner that is loading CAT 785 trucks with high volume coal bodies and payload of 150 t. Operational cutting depth is 24 inches with maximum cutting depth of 36 inches. Surface miner operators determine a cutting depth based on multiple cues, the most important being visual observations of a coal seam being cleaned or mined. The cleaning process involves removal of the last foot of waste material covering the coal seam. This is one of two critical phases in the coal extraction process. If, during the cleaning process, an operator sets a cutting head too deep, valuable product is wasted. If it is set too shallow, waste material is left to be mined with the coal. The second critical phase occurs in the last cut on the interface between the coal and waste material at the bottom of the coal seam. If the cutting head goes deeper than favorable, then waste material is delivered to a power plant.

Feb 27, 2013

By J. E. Friant

The Mini-DiscTM cutter drill bit is a radical design departure from the traditional tri-cone rockdrill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-DiscTM drill bit, referred to as the “Disc Bit” has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory can not shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999

By J. Chenier, M. Boissoneault, D. Ducharme, R. Schonewille

The operation of Falconbridge's Sudbury nickel smelter has undergone significant change since the production was consolidated to a single electric furnace in 1994. In the late 1990's a capital program of about $100 MM (Cdn) was undertaken to expand and modernize the smelter. This project, known as Smelter 2000, was mainly driven by the need to process the new concentrate produced at Falconbridge's Raglan operation in northern Quebec. Included in the scope of the project was the installation of dry concentrate handling facilities, modifications to the roaster feed preparation system, installation of a matte granulation system and modification of one of the converters. Improvements to in-plant hygiene were also an important part of the Smelter 2000 project. Over the past 5 years much has been learned about the challenges in treating two significantly different concentrates. More recently, the introduction of a third concentrate from Falconbridge's new Montcalm operation near Timmins, Ontario has added another dimension to the operation. This paper will describe how the main challenges from the past 7 years have been overcome and discuss the path forward for the Sudbury Smelter Business Unit.

Jan 1, 2005