Search Documents

By E. Shelobolina, S. M. Pickering, J. E. Kogel

A long history of weathering and bacterial alteration processes have transformed Georgia’s Coastal Plain kaolins from dark organic muds to recrystallized white pigment-grade industrial clays. A sequence of six stages in development of these valuable mineral deposits is outlined over their Late Cretaceous and Tertiary deposition and alteration history. Anaerobic and aerobic iron oxidizing and iron-reducing bacteria are present in the Georgia kaolins. These bacteria may have had a major role in iron and organic matter removal during several of the alteration stages that occurred over the past 60+ million years. Iron was likely solubilized by both iron-reducing and iron-oxidizing bacteria, depending on availability of Fe(II), Fe(III), and NO3. Thus, over long periods bacterial activity slowly led to nearly complete groundwater removal of iron from the kaolin deposits. Further bacterial iron removal on an industrial process scale may eventually prove feasible. “Without the multitude of living reactions as channels for energy and electrons and without the enormous capability of life to transfer with and against chemical gradients, there would be practically no or at least a very reduced geochemical rock cycle on this planet.” (Krumbein and Dyer, 1985, p. 157)

Jan 1, 2002

By Giuli M, Barnaba P, Sacerdote R, Tammaro F

Following a theoretical consideration of the effect of flooding, fluidisation and softening on blast furnace blowing limits, results are presented which show the effect of these parameters on operation. Industrial trials on Oscar Sinigaglia No. 4 BF are reported and results compared with those obtained theoretically and in the laboratory. It is shown that in these trials the furnace operated at levels of fluidisation very much (80-90%) below those theoretically calculated whereas in some cases (high proportion of sinter) actual hot metal output was near the calculated flooding limit. However, it was observed that as the sinter percentage decreases also actual productivity becomes lower than the one caused by flooding. This gap, which increases as other ferrous components (essentially acidic) replace the basic sinter was explained by the softening of the burden under bosh conditions. Softening indices measured on the individual materials yield support to this explanation. Coke rates data show that for approximately every one percent increase in the basic sinter in place of blended sized ore, a coke rate decrease of 1.1 kg/thm results. For acidic pellets this value is 0.6 kg/thm. Results of breakdown and reduction characteristics are also given and their indices compared with actual pt oduction. Measures to improve operations are proposed.

Jan 1, 1975

By N. Sahin, K. Baris, A. Ozarslan

This paper aims to assess the current and future role of coal in energy strategy of Turkey and evaluates the compatibility of the policies to the EU energy policy and strategy. The Turkish government set targets to utilize more coal reserves of the country in next decades. However, the country is also in the process of becoming an EU Member State, hence, it is expected that the energy policies have to comply with the EU. Moreover, Turkey ratified Kyoto Protocol, thus the country should limit greenhouse gas emissions. Clean Coal, Carbon Capture and Storage (CCS) technologies are expected to become an important instrument for the mid-term reduction of CO2 emissions from coal-fired power plants. An alternative technique to the conventional CCS methods is CO2 sequestration by mineral carbonation. Turkey has significant resources of magnesium silicate minerals (olivine, serpentine) deposits which can be utilised in CO2 sequestration by mineral carbonation method.

Jan 1, 2011

By Natalie J. Shackleton, Deryck de Vaux, Cyril T. O’Connor, Vratislav Malysiak

"The major losses of PGM and base metals in the beneficiation of platinum group deposits occur during the separation of gangue from the value minerals by selective flotation. A number of studies have shown that this negative impact on flotation is due to surface passivation, caused by various ions that may originate from the external water supply or, as is likely in the majority of cases, from the oxidation of the mineral surfaces and the grinding media. The objective of the study was to investigate the effect surface passivation and inadvertent activation have on flotation and how this can be managed so as to increase the separation of pentlandite and pyroxene. The aim was to minimise the percentage pyroxene reporting to the concentrate and simultaneously maximise the pentlandite recovery. The testwork incorporates the addition of an activator (copper sulphate), a complexing agent, such as DETA (diethylenetriamine) and a dispersant (polyphosphate) at pH 6 and pH 9 in an attempt to alleviate the surface passivation of pentlandite and inadvertent activation of pyroxene. Both synthetic minerals and plant ores were studied in order to determine the effect surface passivation and inadvertent activation have on mineral surface alteration and floatability. Zeta potential determinations, microflotation, ToF-SIMS (Time of Flight Secondary Ion Mass Spectrometry) analyses, laboratory batch flotation tests and continuous flotation testwork were used as tools to study the surface alteration and/or floatability.Zeta potential determinations and ToF-SIMS analyses showed that copper adsorption is non-selective. Both pentlandite and pyroxene become copper (II)-activated in the presence of copper sulphate and subsequently, in the presence of xanthate, adsorption of the collector will occur onto copper activated mineral surfaces. Zeta potential determinations also showed an alteration of the surface charge in the presence of polyphosphate, thereby inhibiting surface passivation of sulphides by slime coatings due to surface repulsion."

Jan 1, 2003

The effect of conditioning energy input on the metallurgical results of an emulsion flotation process has beenattributed by previous authors to a detergency process.This paper shows that such a process does not explain the data and that an attrition mechanism is more appropriate.

Jan 1, 1970

By T. K. Dichmann, J. A. Finch

"Microflotation, laboratory batch, and in-plant minicell continuous tests were conducted to determine if copper ions not only activate sphalerite but also depress pyrite when the minerals are together. Microflotation tests showed that pyrite recovery increased with addition of copper ions in the pH range of 5-10 when alone, but decreased when sphalerite was also present. Batch flotation tests (Red Dog ore) showed that upon addition of copper, pyrite recovery decreased significantly. The continuous tests (Louvicourt Mine) confirmed this and indicated that with excess copper pyrite recovery can increase. The results suggest there is competition for copper and xanthate in favour of sphalerite. To take advantage of this competition it may be necessary to control the sequence and rate of copper, collector, and lime addition. INTRODUCTIONFlotation, in common with all physical separations, is an imperfect process that results in misplacement of minerals. One source of this imperfection is accidental activation by contaminating metal ions. An important practical example is the misplacement of pyrite to zinc concentrates. Flotation of sphalerite generally requires activation by copper ions, added as copper sulphate. Copper ions are also used to activate pyrite [l] hence there is the suspicion that accidental activation contributes to the recovery of pyrite (Py) with the sphalerite (Sp). However, recent literature has shown that copper ions may make Py less floatable if Sp is also present. Xu et al. [2] conducted continuous minicell tests in-plant at Kidd Creek Operations (division of Falconbridge Ltd.) and showed that while the addition of copper sulphate improved zinc/iron selectivity, it did so as much by reducing the recovery of pyrite as increasing zinc recovery (Figure 1)."

Jan 1, 2000

The objective of a mine planning exercise is to plan a safe mine that maximises net present value (NPV) for the project. Two primary elements are key to design of a mine plan optimised to maximise profit: selection of an optimised production rate and selection of an optimised equipment fleet. Both depend upon accurate estimations of capital and operating costs for the equipment and for the life cycle of the mining operation. Once a trial production rate is determined, a primary equipment fleet, ie excavators, haulers, and blasthole drills, can be determined based on material characteristics and haulage distances and gradients. An auxiliary fleet, dozers, road maintainers, service trucks, etc can be determined using less rigid productivity criteria. With an equipment fleet determined, operating and support personnel can be assigned based on shift requirements and equipment operating needs; and material and supply requirements can be estimated. Knowing the areal dimensions of the major equipment items, road widths and repair shop dimensions can be determined. Personnel numbers and supply requirements determine the square metre sizes of offices, change rooms, and storage facilities. Reliable sources of capital and operating unit prices and costs for all these items are referenced in the paper. Once preliminary capital and operating cost estimates are calculated by applying unit costs to equipment, personnel, material and supply needs, potential profit can be tested using DCF techniques. An optimised mine plan can then be determined by testing the potential profitability of multiple mine production rates. Because of the economies of scale, full capital and operating cost estimates must be completed for each production rate in order to produce meaningful comparisons.

Dec 6, 2010

By Lorenzen L, Van Der P F

It is the aim of this paper to review recent research in understanding the role of cyanide in the elution of gold. Under conditions of severe pre-treatment (high temperatures and levels of cyanide), the dynamics of elution are determined mainly by the adsorption equilibrium and the flow conditions in the column. When conditions are less favourable for desorption, transport phenomena are rate controlling. The most important sub-processes of elution are the changes in cyanide, potassium and gold concentrations, as well as the change in passivation of the carbon surface. Mathematical models to simulate the various sub-processes are described briefly.The presence of an irreversibly adsorbed species such as AuCN on the carbon is determined mainly by the pH, temperature and the type of carbon. Cyanide in the pre-treatment step will convert the AuCN to reversibly adsorbed Au(CN)2. Competition between cyanide and Au(CN)z for adsorption sites will enhance the elution of gold, but plays a minor role at elevated temperatures. The most important effect of cyanide is its reaction with the functional groups on the carbon to passivate the surface for the adsorption of anionic metal cyanides and thereby promote the elution of gold. This passivation, caused by the degradation of cyanide, is strongly temperature dependent. Free cyanide in the elution step of an AARL elution is of lesser importance than the cyanide in the pre-treatment step. Elution without cyanide is possible only after cold acid washing, and has been proven on plant scale.

Jan 1, 1992

By David A. Newman

Severe roof control problems have plagued a West Virginia underground mine since its initial development in the late 1970's. Adverse roof conditions in the Eastern portion of the reserve result from a combination of mining: - perpendicular to the major principal horizontal stress direction, - near lineament intersections, - in areas where the ratio of horizontal stress to vertical stress exceeds 2.00 to 4.00, and - where laminated strata are present in the immediate roof. The focus of this study is to identify the engineering (mine orientation, roof safety factor) and geological parameters (lineament and horizontal stress orientation, horizontal to vertical stress ratio, and immediate roof lithology) causing poor roof conditions and to quantify their influence on projected mining conditions in the Western portion of the reserve Rose diagrams were used to illustrate the correlation between the orientation of eight hundred thirty-six (836) roof falls with that of forty-four (44) lineaments and the principal horizontal stress Similarly a composite map was used to demonstrate the relationship between roof falls and the ratio of horizontal stress to vertical stress The immediate roof strata across the property were categorized as either laminated or non-laminated based upon a thorough examination of one hundred sixty-two core logs. The presence or absence of fireclay, a rider coal, and carbonaceous shale was also noted because of the historic correlation with poor roof conditions. Rock strength and physical property tests were conducted on selected immediate roof strata recovered from coreholes drilled along the mains projected to the Western portion of the reserve Potential roof control problems in the Western reserve were quantified based upon the correlations developed by analyzing engineering and geological data The main conclusion is that laminated roof strata, the rider seam, and its associated fireclay will have the greatest influence on mining conditions. Roof problems attributable to horizontal stresses will not be as severe in the West due to an increase in overburden depth and corresponding decrease in the stress ratio. Recommendations are provided for mining orientation, the layout of mains and submains, panel location, and roof support based on intended service life.

Jan 1, 1999

Increasing use has been made of engineer ing geology and hydrogeology in the development of the infrastructure for mining projects. The Geological Survey of the Department of Mines, the Department of Main Roads, the Irrigation and Water Supply Commission and private consulting organisations and mining companies, employ spec- ialist staff to carry out engineering geological and/or hydrogeological investigations. Such in- vestigations have been of assistance in recent mining developments in northern Queensland, in- cluding those in the Cloncurry - Mount lsa, Weipa, Greenvale and northern Borten Basin areas.

Jan 1, 1974

By J McQuie

The concentrator at WMCÆs Leinster Nickel Operation has operated with flash flotation in the grinding circuit since the early 1990s. There has always been a positive correlation between flash flotation Ni recovery and overall Ni recovery û however this relationship could be explained by differences in the ore, rather than by the action of the Flash flotation cell in reducing overgrinding of Ni. In July 2003, refurbishment within the plant made it necessary to operate the concentrator for a period with the flash flotation cells off. The resulting data set provided evidence that flash flotation in the grinding circuit changes the size distribution of Ni to reduce the amount of slow-floating fine (-7 ¦m) Ni produced. Ni recoveries in the finer size fractions were similar with flash flotation on or off û but because less fine Ni is produced when the flash flotation cells are operated, overall Ni recovery improved.

Jan 1, 2005

By D Prior

The Australian mining industry is a significant contributor to the nation’s greenhouse gas (GHG) emissions, and like any industry, it must make efforts to reduce these. Medium- and long-term strategies will include the replacement of diesel engines with alternative energy sources, but what can be done in the short-term to reduce diesel consumption and hence CO2 emissions? Haul trucks are identified as the major contributors of CO2 emissions in the mining fleet and this paper focuses on firstly identifying what drives haul truck emissions and secondly, discussing what is the role of the Fleet Management System (FMS) in reducing these. A key enabler of this is having a robust fuel consumption model within the FMS, and I describe how this may be done. Besides novel approaches to incorporating fuel consumption (CO2) management into truck assignment algorithms, this paper also describes how the FMS can be used to implement and manage procedures and policies to reduce haul truck emissions.

Jun 22, 2022

By I. Jackman

"Gold is present in different forms and associations in different ores. Flotation is used to recover gold and minerals associated with gold, but the applicability and type of flotation vary. The purpose of flotation in a gold recovery plant is largely dependent on the mineralogical association of the gold, and environmental and economic considerations. In this paper, the role of flotation in the recovery of gold is reviewed. The paper will describe examples of gold recovery by flotation including flotation of native gold, gold associated with sulphides including specifically copper sulphides, gold associated with tellurides, gold ores containing carbonaceous material and gold contained in tailings.INTRODUCTIONFlotation is widely used in the recovery of gold. However, the objectives and the mode of application are quite variable dependent on the type of ore, the gold association(s), other metal values, marketing considerations and environmental requirements. In this paper, a range of different applications of flotation incorporated in the recovery of gold are discussed. The reasons for each particular application are outlined and metallurgical results are presented.The mineralogy of the ore and the gold associations are fundamental influences on gold recovery. The use of flotation to concentrate gold is dictated by the mineralogy of the ore and gold. The fundamental factors are mineral/gold size, liberation size, association of the gold and type of gangue minerals or other valuable minerals. Gold can exhibit a range of sizes in a host from relatively large size (+50 µ) to refractory size (1 µ and sub-micron size). Similarly, the gold can occur in a number of phases in the same host. For example, the gold was present as petzite (AgAu telluride), calaverite (AuTe2) and native gold in a gold telluride ore and each of these minerals was associated with the pyrite host.Understanding the gold mineralogy and association is important in establishing the correct process route. The gold mineralogy is established by good mineralogy, use of diagnostic tools such as diagnostic leaching and assay by size fraction analyses and basic metallurgical testwork."

Jan 1, 1995

By M. D. Max, A. H. Johnson

INTRODUCTION Gas hydrates have considerable potential to be a major energy resource owing to their apparent abundance in Arctic regions and along continental margins throughout the world (Kvenvolden, 1988). Yet, the oil and gas industry has been slow to pursue this opportunity. The primary reasons for this are the large conventional reserve base for natural gas worldwide and the perception that gas hydrate will not be a viable resource for another twenty or thirty years. Gas hydrates are thus viewed as a potential resource for the distant future, but not a valid investment for the near term. This paper addresses both global gas markets and gas hydrate technology, and shows that the commercial development of gas hydrate could proceed rapidly enough to constitute a near-term energy resource. GLOBAL GAS MARKETS The proven worldwide reserves of conventional natural gas are truly enormous, totaling over 6,000 TCF according to BP (2004). Moreover, those reserves have nearly doubled during the past two decades and now represent 67 years of consumption at the current production rates of 80 TCF per year (Fig. 1). This reserve increase has occurred even as global production of natural gas has increased by 67% during the same two decades (Fig. 2). While declining conventional gas reserves are a concern in North America, especially in regions where established infrastructure exists to bring gas to consumers, large new discoveries continue to be made elsewhere in the world. Indeed, in many parts of the world (such as the Middle East and parts of West Africa), natural gas has been regarded as an essentially worthless byproduct of oil production or exists in stranded gas fields. Given this situation, pursuing unconventional gas resources that are inherently riskier exploration targets and more expensive to produce would appear to have little rationale from a business standpoint.

Jan 1, 2006

Queensland?s underground coal industry, as a whole, has arguably the best gas monitoring systems in the world. Each mine utilizes real time, tube bundle and onsite ultra fast gas chromatograph systems. Queensland?s mining legislation has specific requirements for mine gas monitoring but there is no requirement for all three techniques. Industry has however identified the need for all three and adopted this as a standard, resulting in over sixty thousand gas results collected each day. Automated monitoring systems are programmed to alarm for gas concentrations, gas ratios and explosibility. These alarms are then used to initiate predetermined actions to take control of the situation and prevent the compromise of safety to workers and the loss of resources. Dedicated software packages have been developed to assist in the interpretation of the large volume of results generated. The real time systems are used for real time warning, essential for incidents such as belt fires. Tube bundle systems suit long term trending used for identification of the onset of spontaneous combustion or for the determination of explosibility during the routine sealing of worked areas. Gas chromatograph analysis is used to provide a complete analysis and provides results for hydrogen and ethylene, key gases used in the assessment of spontaneous combustion. It is also crucial during significant spontaneous combustion events and coal fires to use gas chromatography to determine the explosibility status of the underground atmosphere otherwise the severity of the situation is likely to be under estimated. This paper outlines the need for all three techniques for assessing the underground status and outlines advantages and disadvantages of each.

Jan 1, 2009

Standards in the public reporting of resources and reserves in Australia have dramatically improved since the implementation of the Australasian Code for Reporting of Mineral Resources and Ore Reserves (The JORC Code) in 1989. Whilst the JORC Code states clearly that Mineral Resources and Ore Reserves are imprecise calculations and should be treated as estimates, there is strong evidence that many people regard them as fact, including some accountants, directors, auditors and investors. Mineral Resources and Ore Reserves are key inputs in the valuation of a mining company and the determination of financial performance. Geological knowledge is the foundation upon which Mineral Resources, Ore Reserves and investment decisions are made, however this information carries with it substantial uncertainty. Case studies and company reports have established that errors derived from inadequate geological inputs have led to reduced profitability in operating mines and in extreme cases the premature closure of mine operations. Whilst there are many causes of mine closure and reduced profitability, including commodity prices and exchange rates, the cumulative effect of all geological uncertainty contributes significantly to the erosion of the credibility of mining within the investment community. There are a number of methods used to characterise and model uncertainty in Mineral Resource and Ore Reserve estimation. Empirical mining indexes, sensitivity analyses, Monte Carlo simulations and Conditional simulations are used to identify and estimate geological uncertainty, notably the quantification of uncertainty in grade and tonnage estimates. These techniques have not generally been applied to estimating geological uncertainty associated with key Ore Reserve inputs such as appropriate mining technique, equipment selection, production rate, mining dilution, stability requirements, materials handling, metallurgical processing, product quality and waste storage. New software tools are needed to model the entire mining process with all its geological and other interdependencies, enabling all uncertainties to be separately identified and estimated. By its very nature, mining involves the assumption of significant technical, financial, political, environmental and social risk. Success comes by understanding and managing these risks and consequently the mining industry will never choose to reduce the level of geological uncertainty to nil. The ultimate aim of improved identification and estimation of geological uncertainty is to quantify inputs into the Ore Reserve process, allowing a company to assess the risks and manage these accordingly. This approach is relevant to feasibility studies for new projects as well as life-of-mine planning through to the weekly schedule at existing mines.

Jan 1, 2003

By P Voulgaris

The Osborne Mine commenced production from an open pit in December 1994 with the first ore being hauled from underground one year later. Currently all ore is hauled up a decline by trucks until the shaft system is commissioned in early-1998. The mine is hosted within a multiply deformed and complex sequence of metamorphic, igneous and metasomatic rocks of mid Proterozoic age that are concealed beneath 20-40 metres of Mesozoic sedimentary cover. Epigenetic and largely hypogene copper - gold mineralisation occurs in a close spatial relationship with quartz - magnetite ironstones and is an important example of a significant mineralisation style in the Mt Isa inlier. Life of mine concentrator production, to year end 1997, totals 3.2 Mt of ore at 3.40 per cent Cu and 1.13 g/t Au. Total metal produced was 97 000 tonnes of copper and 2900 Kg of gold (95 600 oz) from some 348 000 tonnes of dry concentrates averaging 28.01 per cent Cu and 6.99 g/t Au. At the start of 1998 OsborneÆs total measured and indicated resource was stated at 11.38 Mt at 3.24 per cent Cu and 1.21 g/t Au with an ore reserve of 11.42 Mt at 2.90 per cent Cu and 1.09 g/t Au. Exploration efforts in and around the mine have been increased since 1996 and have resulted in an early success, with a 28 per cent increase in ore reserves since mine start-up, and the establishment of a 1.5 Mt inferred resource open to depth. During 1997 the performance of the concentrator has exceeded expectations with throughput having been increased to 1.45 Mt per annum. The Mining Cycle at Osborne has proceeded from discovery through feasibility and is currently seen to be in the latter part of the development stage and/or the early part of an expansion stage. This paper will describe the role of geology and exploration within these stages and will highlight how a number of key interpretations and decisions based on geology have both favourably and unfavourably affected the project.

Jan 1, 1998

By Alan Bye, Megan Little

Geology, and the detailed understanding of its properties, are fundamental to the optimal design and successful operation of any mine. To that end extensive fieldwork has been conducted at Anglo Platinum?s PPRust operation to collect geotechnical information both from exploration boreholes and in-pit mining faces. Since 1998, geotechnical data has been collected from over 337 km of exploration core, 7 km of exposed mining faces and more than 15 600 field and laboratory tests, in order to define the complete set of geotechnical properties for each rock type in the mining area. The geotechnical information collected is stored in two databases, SABLE Warehouse and MineMapper3D before it is imported into the Datamine mining software package. The geotechnical parameters, mining rock mass rating system (MRMR), uniaxial compressive strength (UCS), fracture frequency per metre (FF) and rock quality designation (RQD), are modelled using geostatistics to generate a 3D geotechnical block model. Data is interpolated between exploration boreholes and exposed mining faces and modelling is constrained, using wireframes, by rock type and structural features. By having detailed geotechnical information available in a 3D model that can be readily accessed and interpreted, significant production optimisations, feasibility studies and planning initiatives can be implemented. From a slope design perspective the model is used to target data deficient zones and highlight potentially weak rock mass areas. As this can be viewed in 3D, the open pit slopes can then be designed to accommodate the poor quality area before it is excavated. It also follows that geotechnical zones can be readily identified and the slopes optimised accordingly. Rather than viewing the drill and blast department as an isolated cost centre and focussing on minimising drill and blast costs, the fragmentation requirements of the comminution and load and haul business areas are studied. It is well understood that chemical energy is the cheapest form of comminution and that major downstream benefits can be derived by increasing drill and blast expenditure. 238 blasts were assessed to determine the optimum fragmentation requirements for ore and waste. Based on the study a mean fragmentation target of 150 mm was set for delivery to the crushing circuit and a mean fragmentation of 230 mm was set for waste loading from the pit. Substantial benefits have been realised in the drill and blast department by developing empirical correlations that relate the MRMR values in the geotechnical model to a blastability index, fragmentation, required powder factor and costs. As the geotechnical model can predict changes in geotechnical conditions, the blasting

Jan 1, 2007

It has been thought in the past that New Zealand had ample coal reserves, able to provide fossil fuel supplies well into the future. Such is not the case and every effort must be made to achieve the highest possible extraction rate in all new coal mining ventures. While the relative cost and availability of completion or fuels has been largely responsible for the slow growth of coal production in the past, a world shortage of fuels has given coal a new importance and required better utilisation of coal reserves. New mining ventures in thick-seam coal deposits cannot be planned and designed without geotechnical investigations designed to provide information required by the mining engineer and analyst. Finite element analysis of mine workings may provide essential information on the optimisation of mining techniques and the design of underground support and roadway shapes.

Jan 1, 1976

By M. Pineda

Sublevel stoping (SLS) is one of the oldest and most used methods for underground mining. It relies heavily on the use of drilling and blasting techniques to remove the rock, and gravity to transport the broken rock to drawpoints located at the base of the stope, with LHDs to transport material from the drawpoints. Current SLS operations are based on the assumption of stable geometry of the stope. Thus, the stope design includes the definition of the geometry according to the orebody shape and geomechanical constraints to avoid instability, which may cause excessive dilution. Under some circumstances, dilution could enter the stope due to geotechnical instability, especially when large stope geometries are used. A review of current design and planning practices for large SLS operations indicates that no consideration is given to the material flow and the mixing that occurs after blasting. Material flow could have a large impacton the mixing of ore when grades are heterogeneous in the stope. In this paper, we discuss the influence of gravity flow on the design and planning of large sublevel stopes with and without vertical dilution, based on laboratory experiments. The outcomes of this investigation are used todevelop guidelines towards the design and planning of large SLS mines, which would complement the currently used geotechnical considerations.

Jan 1, 2015