Search Documents

By S. H. Ash

THE INVESTIGATION of barrier pillars in the Western Middle field is part of the comprehensive study of the mine-water problem in the anthra¬cite region of Pennsylvania by the Federal Bureau of Mines (1, 2, 5, 6, 7, 8,9,10,11,1,2,15,16).8 The Western Middle field is in Schuylkill, Columbia, and Northumberland Counties in eastern Pennsylvania. It has an area of 120 square miles, is 42 miles long from Delano on the east to Trevorton on the west, and is 2 to 5 miles wide. In the Western Middle field are 58 underground water pools containing 38 billion gallons of water (5). Some of the pools overflow to the surface, and the water from others seeps into adjacent mines through permeable barrier pillars separating them from abandoned mines. Several active mines are interconnected to workings in abandoned mines, which are partly filled with water. These mines are separated by barrier pillars that are considered effective only below the altitude of the connections. In some abandoned mines, pumping stations maintain the water at altitudes where the hydrostatic pressure against the barrier pillars is not excessive and does not endanger adjacent active mines. If water in these abandoned mines is allowed to rise to where it can overflow into the active mines, it must be pumped from the active mines at lower altitudes; this materially increases the cost of pumping. It is estimated that from 1944 to 1948 approximately 30 percent of the water pumped to the surface was from abandoned mines.

Jan 1, 1953

The commercial development of the shallow (2200 ft2 400 ft) Windalia sand reservoir at Barrow Island provided the opportunity to conduct an intensive drilling programme using equipment and techniques designed for optimum performance.During the initial exploratory and reservoir delineation phase, 12 specific Windalia test wells were drilled using drilling equipment with an optimum depth range of 6QOO ft - 8000 ft and a 9 5/8 in by 7 in. casing programme was employed. The average time from commencement of move-in to rig release exclusive of coring for five representative wells was 187 hr during this phase.Development drilling commenced December 1966 with one rig, with the second in operation January 1967.As of January 1 1968, 168 development wells had been completed. The two rigs employed are drive-in units equipped with a telescoping .gelf raising doubles mast.Optimum depth range with 4 1/2 in. drill pipe is 2500-4000 ft. Casing programme is 8 5/8 in. by 5 1/2 in. Efficient performance was achieved immediately. The average time from commencement of move-in to rig release for 15 wells drilled early in the development programme was 99 hr.By application of experience and further modification of techniques, performance was improved to an average time of 72 hr per well for 15 wells recently completed.The major drilling problem on Barrow Island is surface hole drilling due to the very hard surface limestone combined with complete loss of circulation at sea level.In this operation, significant improvements have been effected. During the exploratory phase drilling, 12 1/4 in hole to set 9 5/8 in. casing, average penetration rate was 23 ft/hr. At the commencement of the development programme penetration rate, drilling 10 5/8 in. hole to set 8 5/8 in. casing, was 28 ft/hr for the 15 early wells considered, improving to 55 ft/hr for the 15 recent wells considered.This programme is a team effort and much credit must be given to the enthusiastic co-operation of the two drilling contractors.The current field record is 2 days 4 hr with a 4 1/2 hr move including the drilling of mousehole and rathole.

Jan 1, 1968

By G. A. Wells

The consumption of barytes in certain paints, polyurethane foams, seamless flooring, glass, brake linings, plastisol gaskets for food containers, and in fluids used for gastrointestinal X-ray examinations relies on the unique properties of barium sulfate. There are no readily available mineral substitutes. Barytes are also the essential raw material for the manufacture of industrially important barium chemicals. High quality barite ore has become scarce throughout the world. Processing ore into quality end products is both capital and energy intensive. These factors have tended to limit availability and increase Prices which have encouraged the use of alternative or competitive materials and restricted market growth.

Jan 1, 1981

By W. J. Kingwell

My comments and questions are addressed to Mr. Troughton. It seems to me that the tests were very well tailored to determine long term effects on performance of bearing piles as groundwater pressures rise in the London Basin. This rise is being simulated by means of a groundwater recharge system but it would be informative to have further details of the controls of conditions simulated. Ideally the porewater pressure in Standpipes 1, 2 and 3 should be the same throughout the test. Under test conditions are there not practical dif­ficulties? Recharge Well C2 is a lesser dis­tance from the pile than the other wells. Was the rate of recharge to C2 regulated to a lesser rate than the other three? In my experience the rate of acceptance usually varies from well to well. Under a common feed pressure were mea­sures taken to compensate for this? Since the problem does not only affect London, but also Liverpool, Nottingham, Birmingham and to a lesser extent, Manchester, I question whether an ideal procedure is being used. It is well known that rates of acceptance decrease with time and often recharge wells need to be flushed out at regular intervals. Other pro­cedures may need to be adopted to accurately simulate the effect of groundwater rise, if tests of longer duration are to be considered.

Jan 1, 1991

By M Fewings

This paper casts a light on the sometimes murky world that lies between base metals product æout the gateÆ, and money in the bank. Whether your base metals are leaving the mine as a refined product, or as an ore or concentrate, the generally accepted method of value determination is a London Metal Exchange price, usually measured at some point after the material has left your control. In this paper, the structure and operation, regulation and the reasons for the use of the London Metal Exchange are explored. In addition, the risks and opportunities that terminal market pricing provides to mine managers are explained, with particular reference to hedging. The paper also deals with the structure of the sales contract, including management of shipping issues, agreement of delivered quality, documentation and administrative issues. The selection of counterparties, the role of traders in the market and the growing influence of China and India as base metal consumers and competitors are also addressed.

Jan 1, 2006

Base metal sulphide mineralisation on the northern end of Great Barrier Island is spatially associated with hypabyssal intermediate to acidic intrusives, in transgressive structures in indurated, complexly deformed greywackes and argillites. Copper predominates in the mineralisation, with minor accompanying lead and zinc and also some gold and silver. However, in some cases lead or zinc may be the dominant constituent. The mineralisation is generally characterised by only narrow envelopes of weak alteration (propyliticassemblages dominated by chlorite and epidote) and with only minor amounts of quartz accompanying the sulphides, which form a cement in zones of hydraulic fracturing. There are two distinct structural settings to the mineralisation: at MinerÆs Head, in a structurally complex situation in a shell-like zone of crackling in hornfelsed greywacke, in association with both north- and east-striking fractures and rubble breccias associated with the apical part of a large intrusive; and in very narrow, but very strike-persistent, 1inear steeply-dipping fracture zones, exposed on the north coast and inland areas near Tataweka.

Jan 1, 1984

By J. M. Gregg, C. J. Persellin, I. D. Somerville, E. A. Atekwana, K. L. Shelton

"Zn-Pb sulfide mineralization at Abbeytown mine and Twigspark quarry comprise the only known car¬bonate-hosted base metal sulfide deposits in the Sligo syncline, northwest Ireland. Limestone sedimentation occurred uniformly throughout the region during the Early Carboniferous (Mississippian) as observed by field relationships and lithofacies; however, petrographic and stable isotope evidence indicate that host-rock dolomitization occurred under different conditions at localities to the west and east of the Ox Mountains inlier, suggesting significant uplift and geologic isolation of these areas prior to dolomitization. Localized fluid flow systems are thought to be responsible for sulfide mineralization and associated epigenetic carbonate cements. West of the Ox Mountains inlier at Abbeytown, evidence of three geochemically distinct fluids are observed: (1) a lower-temperature, lower-salinity fluid (70°-130-°C, 4-9 wt.% equiv. NaCl); (2) a lower-temperature, higher-salinity fluid (70°-140°C, 15-24 wt.% equiv. NaCl); and (3) a higher-temperature, moderate-salinity fluid (165°-220°C, 8-14 wt.% equiv. NaCl). Similar fluid types were observed at the Twigspark deposit. The source of the higher-salinity fluid is likely seawater evaporated to near the point of halite precipitation. The higher-temperature fluid is thought to have been derived from deep circulation of basinal brines. It is speculated that mixing of the higher-salinity fluid with the high-temperature fluid was vital for ore formation at Abbeytown because fluid inclusions in sphalerite have homogenization temperatures and salinity values that fall along a mixing trajectory of these end member fluids. Also, areas where the high-salinity end member fluid is absent are barren of sulfides. Less complex fluid systems are indicated for sites east of the Ox Mountains inlier where no sulfide mineralization was observed. Data from base metal sulfide prospects in northwest Ireland indicate no connection with the regionally extensive flow system thought to be responsible for Zn-Pb deposits throughout the Irish Midlands.Les minéralisations en sulfures de Zn-Pb de la mine Abbeytown et de la carrière Twigspark sont les seules gîtes de métaux usuels à encaissant carbonaté connus dans le synclinal de Sligo, au nord-ouest de l’Irlande. Ces carbonates se sont déposés d’une manière uniforme dans la région au Carbonifère inférieur (Mississippien) tel que l’indiquent les relations de terrain et les lithofaçiès; les données pétrographiques et d’isotopes stables indiquent toutefois que la dolomitisation de l’encaissant s’est faite sous des conditions différentes aux localités situées à l’ouest ou à l’est de la boutonnière des Ox Mountains, ce qui suggère un soulèvement et une isolation géologique significative de ces secteurs avant la dolomitisation. L’action de systèmes de circulation locaux sont considérés être à l’origine de la minéralisation sulfurée et des ciments carbonatés épigénétiques qui leur sont associés. À Abbeytown, à l’ouest de la boutonnière des Ox Mountains, on note les effets de trois fluides géochimiquement distincts: (1) un fluide à basse température peu salin (70°-130°C, 4-9% poids équivalent NaCl); (2) un fluide à basse température fortement salin (70°-140°C, 15-24% poids équivalent NaCl); and (3) un fluide formé à plus haute température et salinité modérée (165°-220°C, 8-14% poids équivalent NaCl). Des fluides similaires ont été observés au gîte Twigspark. La source présumée du fluide le plus salin est de l’eau de mer amenée par évaporation près du point de précipitation de la halite. Le fluide à plus haute température est probablement dérivé de la circulation profonde de saumures dérivées d’un bas¬sin sédimentaire. Il est possible que le mélange du fluide à haute salinité avec celui à haute température ait joué un rôle central dans la genèse de la minéralisation d’Abbeytown parce que les températures d’homogénéisation et les valeurs de salinité des inclusions fluide"

Jan 1, 2009

By S E. Munro, P D. Munro

The commonly traded base metals concentrates of copper, lead, tin and zinc are sold by miners to custom smelters using contracts whose terms were generally established at the beginning of the 20th century or even earlier. Technical clauses in these concentrates for items such as payable metals and penalty elements do not reflect current realities of extractive metallurgical technologies and hygiene/environmental issues.It is an axiom that the miners and smelters have a symbiotic relationship. While the existing antique and arcane commercial arrangements serve the purpose of transferring money from the buyer to the seller, they are not likely to result in the industry achieving better overall technical and economic outcomes. By examining the cases for copper concentrates and zinc concentrates in particular, it will be shown that the practical application of these antiquated technical clauses does not drive the miners to produce the better quality concentrates that should be desired by the smelters. This is despite development of mineral beneficiation and hydrometallurgical technologies that would allow the miners to make better products.The adage that any extractive metallurgical problem in the smelter is cheaper to solve in the concentrator still generally holds.While nickel concentrates are only touched on lightly in this discussion because sales terms are more opaque than those for the other base metals, it is expected that the same conclusions will apply.CITATION:Munro, P D and Munro, S E, 2015. Base metals concentrate sales contracts – change Pavlov and the dog, in Proceedings MetPlant 2015, pp 46–60 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

Flue dust from the sintering of base metal sulphides was leached to remove cadmium and arsenic. Leach liquor contained cadmium, zinc and small amounts of other base metals as chlorides. Results are reported of the use of a cation exchange resin Zeocarb 225 to separate the base metals from the arsenic. The resin was eluted with sodium chloride or sulphate to give a solution of relatively concentrated cadmium suitable for recovery by zinc cementation. The limited solubility of sodium sulphate presented some practical problems which were investigated. Another problem was the precipitation of lead sulphate in the resin during elution.INTRODUCTIONWhen lead-zinc sulphides are sintered prior to smelting, the gases passing to the flue are mainly uncondensable but contain a certain proportion of sublimates and dust particles which deposit in the flue or are carried, after condensation in the gas stream, to some form of dust extraction equipment.The recovered dust is a complex mixture of base metal sulphates, sulphites, sulphides, chlorides and oxides, the composition depending on the original concentrates. A large proportion of the cadmium and some of the arsenic originally in the concentrates finds its way to this flue dust, the treatment of which can be a convenient means of removing these elements and controlling their concentrations in the main lead-zinc smelter circuit. However, disposing of this material represents an appreciable waste of base metals as well as a serious toxicity hazard.Sulphide Corporation Pty. Ltd. was faced with this problem in planning the flow sheet of the new lead-zinc smelter at Cockle Creek, N.S.W. From a test run carried out on a pilot plant at Avonmouth, U.K., using a mixture of lead and zinc concentrates, a sample of dust was obtained for...

Jan 1, 1960

The heap leaching of base metal ores can be applied within a number of different scenarios, each requiring its own set of parameters to be determined during the metallurgical testwork programme. The occurrence of acid-gangue reactions and its concomitant precipitation reactions is a factor common to all cases, and requires that the optimal irrigation acid strength be found that optimises the combination of extraction kinetics, acid consumption and possible premature blinding of the heap due to precipitation reactions. For the heap bioleaching of base metal sulphide ores the oxygen requirement needs to be determined for the design of the aeration system, and the operating conditions employed need to also facilitate bacterial growth over and above the acid strength optimisation mentioned above. For the heap bioleaching of chalcopyrite, the need to preserve heat in the heap becomes yet a further parameter of critical importance. For the heap leaching of uranium ore a choice is required between either chemical or bacterial oxidation, based on economic and processing factors. Frequently the operating parameters need to be determined for a circuit in which heap leaching is combined with tank leaching and/or pressure leaching. The processing implications and metallurgical testwork approach for each case is discussed.

Jan 1, 2007

By Steven R. McCutcheon

ABSTRACT - The Bathurst-Newcastle district, a subcircular area approximately 50 km in diameter, contains 37 massive-sulfide Zn-Pb-Cu deposits that have defined tonnages, and has 58 additional significant occurrences. The largest deposit is Brunswick No . 12, with total reserves (including past production) of 148 million tonnes grading about 12.50% combined Pb-Zn. The deposits/ occurrences are spatially associated with a felsic volcanic pile that contains a significant sedimentary component. In the vicinity of the Brunswick deposits the pile is divisible into lower and upper sequences. The lower is characterized by megacrystic rhyolite (QFAS) and coarse- to fine-grained quartz ( ± feldspar) wackes and/or tuffites (QAS); the upper sequence is characterized by aphyric to sparsely porphyritic rhyolites (HWR), micro-breccias, and acid hyaloclastites with interbedded dark gray sedimentary rocks. A greenish gray to dark gray siltstone (GGS) separates the two sequences and hosts the sulfide deposits. Lithogeochemistry of !east altered samples shows that the QFAS and HWR have an igneous character, whereas the QAS and GGS have a sedimentary sig­ nature. The two types can be distinguished on the basis of total alkalies (Na2O + K2O) versus SiO2/Al2O3, and Ti02 versus Fe/(Fe+ Mg). Some trace elements, such as Sr and Y, also help differentiate the two types. The QFAS differs from HWR by having higher La/Yb ratios but lower Zr and Th. The Bathurst deposits do not show a close spatial association with rhyolites but rather are stratiform bodies (lacking clastic textures) within fine-grained sedimentary rocks. The scarcity of barite and other sulfates indicates that there was little mixing between the metal­ bearing fluids and cold seawater. High Fe/(Fe+ Mg) ratios in chlorites also indicate the fluids did not contain a significant seawater component. These features and the large size of many deposits suggest that the deposits formed from metal-rich pore waters that were released catastrophically from an acquifer in the footwall stratigraphy.

Jan 1, 1992

By Madan Kumar Annam, Hari Krishna Y

"Basement construction is one of the challenging geotechnical concerns in the urban environment. Several types of retention systems are practiced to support the earth which is suitable for restricted access, rapid mobilization, fast excavation and cost-effective designs. A thorough understanding of geotechnical engineering as well as the structural mechanics is important for the earth retention systems. This paper discusses a project with various types of foundation solutions including monitoring of deflections during excavation stage of a retention system.A multi storeyed residential building (3B+Stilt+18F) in Chennai having structure foot print area of 1500 m2 has to be constructed on large diameter pile foundations and also to support the proposed basement excavation. Ground water table was encountered at about 6m below the existing ground level (EGL). In order to support heavy structural loads, large diameter bored cast-in-situ piles were chosen and installed. Further, complete retention system was economically designed and built, which includes installation of Contiguous Bored Piles (CBP) in combination of vertical grout columns behind CBP wall to seal the gap between the CB Piles, installation of inclined ground anchors, construction of capping beam, stressing and locking of installed ground anchors. A detailed monitoring program was in place and continuous monitoring of wall deflections is being measured at the time of publishing this paper. This paper describes the design and construction aspects adopted for foundation and retention system including the monitoring results during excavation stage of the project.INTRODUCTIONIn general, stage wise open excavation will be opted for basement construction where plenty of space is available. Due to urbanization and restricted space, open excavation became a difficult task nowadays. To overcome this problem, suitable retention system need to be selected to retain the soil mass. Selection of suitable retention system for multi-level basement excavation is a great challenge in geotechnical industry, especially when the proposed site is located within the minimum set back distance from the existing structures. This in turn calls for the advanced and innovative methods of retention system.Several earth retention systems such as Diaphragm Walls, Secant Pile Walls, CBP system, Soldier Pile Walls, Sheet Piles, Deep Soil Mixing (block walls) etc. with or without inclined ground anchors are being practiced worldwide. Considering the advantages and disadvantages of the available retention systems in practice locally and keeping in view of present site conditions, the developer has chosen CBP system with inclined ground anchors so that all foundation related works of the project will be handled in a single package. The main advantage of such packaged solution will ease the coordination between design consultants and foundation contractor resulting in faster construction of foundation works which in turn reflect savings in time and cost."

Jan 1, 2015

By Petr Sulovsky, Jaroslava Ledererova, Miroslav Svoboda, Michaela Suchardova

"The thinning resources of natural raw materials necessitate an increased degree of waste material recycling. The building industry offers a range of technologies enabling incorporation of industrial wastes into building materials for construction purposes in an economically acceptable way. Our research is focused on finding the appropriate technologies for specific groups of industrial waste materials (IWM). The studied IWM involve coal combustion residues (CCR), desulphurization products, sludges, metallurgical slags, and various other wastes. Many of them contain increased amounts of toxic elements that can under certain conditions get released. In order to prevent this, each specific IWM requires finding the technology that best ensures the binding of toxic elements in the building matter are fixed for the long term.Introduction The sustainable development of mankind is more than ever viewed as a matter of resources. Many aspects of the switch from a throw-away to a recycling society concern one of the largest consumers of natural resources and producer of greenhouse gases, the building industry. One of the biggest tasks lying before the researchers in the field of building materials is to find substitute or alternative raw materials that would save the thinning reserves of natural resources. The most promising and natural way is to replace the traditional raw materials with rejected and unwanted products of industrial processes, classified as wastes. These of course are not produced with the primary intention of achieving some desired properties. The usage of industrial wastes therefore involves finding the optimal way of usage their existing positive (from the point of view of utilizations) properties and minimizing the impact of their undesired properties, i.e. from the perspective of the considered application."

Jan 1, 2008

By B. R. Reddy, Y. V. Swamy, B. V. R. Murthy, H. S. Ray

The Ni oxide was reduced with a CO-CO2-N2 gas mixture and the effects were observed of process variables such as roasting temperature, time and CO partial pressure. Extraction of over 90% of Ni was achieved by ammoniacal leaching of ore that had been reduced for 1 h at 760 degrees C under a gas mixture with a volumetric CO/(CO+CO2) ratio of 0.57. The kinetic data were found to conform to the Ginstling-Brounstein equation. The applicability of this model was confirmed by evaluating the apparent activation energy with the use of independently constructed differential and integral plots, which showed an excellent match

Dec 1, 1995

Gullies are the vital in-stope excavations that provide access for mining personnel and material to, and mined ore from, the producing faces in the tabular hard rock mines. They pose a serious problem in most mines because they induce stress orientations, which, combined with blast damage, produce adverse rock fracture patterns that contribute to the loss of hangingwall and sidewall integrity. Rock-related injury statistics confirm this by highlighting gullies as the second-highest risk area in South African hard rock mines. Inappropriate gully geometries, poor blasting practice, and non-adherence to accepted standards worsen the problem. The aim of this work is, firstly, to provide guidelines to select the correct gully geometry and appropriate support for a particular geotechnical environment and, secondly, to review the practical issues behind gully safety and stability. In order to meet these aims, this paper reviews the available literature on gullies and their history, and reports on an industry-wide survey of practices and opinions. Then it covers observations from underground visits to 107 gullies situated in the respective geotechnical environments of the Basal Reef, Beatrix Reef, Vaal Reef, Carbon Leader Reef, Ventersdorp Contact Reef, Kimberley Reef, Kalkoenkrans Reef, Merensky Reef, and UG2 Reef. Despite the differing geotechnical conditions and gully geometries, common problems are experienced with geological structure, stress, and fracturing. Results from numerical modelling are also presented to help analyse the underground observations and to quantify the merits of the different gully layouts. It is concluded that there are no new techniques available to improve gully stability, but that significant improvements in safety are attainable by employing the correct gully geometry for the geotechnical environment, good blasting practice, and appropriate support.

Jan 1, 2002

By Yindong Yang

Despite the importance and usefulness of basicity in metallurgical slags, the optimum quantitative expression of it has remained elusive, partly due to the fact that the precise concept of basicity has not been properly clarified. The two basic approaches to the concept of basicity are the Lux-Flood, which perceives basicity in terms of the activity of the free oxide ion, a O2- , and the Lewis, which perceives basicity in terms of the ability to donate negative charge. The former has been almost universally adopted in the area of metallurgical slags, while the latter has been increasingly accepted in the field of glass chemistry. In this paper, some difficulties of the Lux-Flood approach are pointed out, including the need for indirect measures of a O2- , which have proliferated in recent years. Accordingly, it is suggested that the Lewis approach has a good deal to commend it, and that the quantification of it in terms of optical basicity is the best measure of basicity available, which should therefore be more widely applied in metallurgical slags than it currently is. The fact that there are intrinsic problems in evaluating the optical basicities for the transition metal oxides is acknowledged, and a new scale is recommended. The patterns of iso-optical basicity lines in ternary systems are shown to agree well with the pattern of iso-activity and iso-capacity lines under appropriate conditions. * Originally published in the Proceedings of MINPREX 2000, published by The AusIMM.

Jan 1, 2001

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structurallife often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response and a simple estimate of structural life for haulers.

Jan 1, 2011

By Anthony J. Konya

"This paper was written during part of the author’s student co-op with Cargill Salt at its Avery Islandunderground salt mine in Louisiana. Blasting salt is a unique type of blasting that is different than blasting other rock types. The plastic nature of salt, along with its large swell factor make salt a challenge to blast. The Cargill salt mines use and have tested a variety of different methods for breaking salt in an efficient manner, however these blasting methods are rarely used in other operations nor talked about today."

Jan 1, 2016

By N September, R Abate

Bateman Modular (previously Van Eck and Lurie) has been building and supplying the mining industry with modular DMS plants for the last 30 years. These DMS modules range in capacity from 1 tph to 200 tph. The most popular unit produced by Bateman Modular over the years has been the 50 tph module. Development In the last 7 years a need has arisen from the industry to provide Modular DMS plants that can treat higher tonnages (150 to 200 tph). The first DMS provided to the mining industry based on the modular concept was a 150 tph DMS Module to MIBA in the DRC. Since then Bateman Modular has provided some 14 Mega DMS modules over the last 7 years with the latest two orders from Debswana (Damtshaa double up project) and Namdeb. Ever since the first Mega Module was supplied Bateman Modular has been improving the Modules. Implementation The modules can be supplied in different configurations so as to improve the overall availability of the plant. Two off 150 tph DMS modules were supplied for a Transhex operation. This allowed the client to still operate one DMS module while maintenance is being performed on the other DMS module. The client also has the option of choosing a single module. Successes The following list of projects provides the base for the success of the Mega Modules.

Jan 1, 2006

BATMINÖ, BATMINEÖ, BATMINDÖ are an abbreviation for Business Analysis Tools for Mining, Mine Evaluation and Mine Design respectively. BATMINP are proprietary tools customised to suit individual client requirements. The first suite of tools provides for analysis and evaluation of open pit mining equipment alternatives and includes fleet selection, fleet sizing and production, productivity and economic outcomes. The models address all mine process activities including drilling, blasting, loading, hauling and auxiliary services. All models are built to provide for simultaneous evaluation of multiple alternatives that are time and condition related. Provision is made for modelling from first principles and/or default or shortcut inputs. Sensitivities to key input parameters are easily performed and consistent logic is applied throughout the process. The models are built to provide key outputs in a format suitable for presentation and documentation. Provision is also made in the models for validation of both inputs and outputs through benchmarking, back analysis and budget comparison. The same models can be used for short interval (12 month) planning and control, medium-term (three to five years) and long-term life-of-mine (LOM) planning. Millions of dollars are spent each year on mining plant and equipment. Decisions that impact on the medium and long-term are made. BATMINP tools have been used to perform studies with good results and in most cases the studies have been validated through back analysis and comparing model outcomes to real data.

Dec 6, 2010