Search Documents

By Harumasa Kurokawa

Since the initial start-up, the Toyo Smelter & Refinery has been operating in harmony with the ambient environment, and improvements have been implemented with technologies specifically developed for further protecting the environment. Toyo Smelter & Refinery is now planning to increase the copper production capacity from 280,000 tpy to 450,000 tpy, over a period of several years. In 2003, the first step of this smelter expansion and modernization plan was implemented. The production capacity of the P-S converter was increased dramatically, as it became possible to operate under a ?2 hot-2 blowing? schedule. In 2005, an additional converter will be installed, in order to allow operation under a ?3 hot-2 blowing? schedule. This report will describe the technical improvements on the P-S converters, as well as describe the Toyo expansion program and discuss the technologies applied to the fugitive gas collecting system.

Jan 1, 2005

By Emmanuel Portilllos

Every paste backfill system is typically unique, this being due to the particular tailings characteristics, the backfill recipe and requirements of mine planning. Key to successful transport to the underground workings through the boreholes and the distribution pipelines is the quality of cemented paste, being free of lumps and recipe components uniformly mixed. Certain types of mixer require that the mixing environment is required to be intensive as possible. In this sense, the present paper point out some of the general aspects of paste plant design, a short discussion on paste recipe and process equipment, followed by a technical comparison between a batch mixing and a continuous mixing process, currently applied to the production of cemented paste tailings for mine backfill.

Sep 9, 2007

By R. Bauer

Adaptations and redesign of the existing already very successful and proven road milling machine concept and technical innovations such as an optimized, specifically for mining application developed cutting drum, cutting housing design and cutting tools, high manoeuvrability achieved via a tight turning radius, a three disk clutch system and a cutting drum drive that allows for the acceptance of higher loads, a complete reinforcement of the chassis to withstand higher vibrations and torque, the installation of increased engine power via a modern drive unit, a specifically for mining/construction applications developed operator’s platform and finally a redesigned air intake system and the adaptation of the levelling system resulted in far more cost effective and advantageous capabilities of Wirtgen Surface Miner in soft to medium hard mining and construction applications. As the achieved results show for the first time in modern surface mining history mechanized cutting is capable to compete successfully against traditional drill, blast/ripping and other conventional mining methods.

Jan 1, 2007

By J. B. Hiskey

Introduction The domestic copper industry has suffered for some time from declining ore grades; rising costs associated with conventional mining, milling, smelting and refining; tightening environmental restrictions; and shrinking markets due to materials substitution. Ore grade depletion is a major problem. It is illustrated by the decline in average copper yield shown in Fig. 1. From 1979, copper grade has dropped 60%, lowering yields from 1.2% to 0.49% (Sousa, 1981). The US copper industry is taking drastic measures to enhance its competitive posture and to guarantee its future worldwide position. In a sense, this involves a general restructuring of the processing philosophy of US copper producers. Judging from recent trends, this restructuring relates to the application of solution mining techniques to the treatment of copper ores and low grade waste material. Recovering copper by leaching techniques has been practiced for centuries. As early as the mid-16th century, some Hungarian copper mines were recycling copper bearing leach solutions through waste heaps (Nash, 1912). In the US, recovering copper from dilute mine waters has been carried out for more than 100 years. There are, however, certain technical innovations that have elevated the importance of solution mining as a process for copper recovery. These include: • Advances in solvent extract-electrowinning (SX-EW); • Developments in acid and acid ferric cure processes for oxide and mixed oxide sulfide ores; • Improvements in heap and dump construction; and • Advances in in situ leaching technology. Generally, solution mining enjoys certain intrinsic advantages over conventional mining and milling. Compared to conventional milling, the combined capital and operating costs of leaching facilities are normally lower, start-up times are faster, and the leaching operation usually has less impact on the environment. Furthermore, solution mining represents an expedient way of extracting metals from small shallow deposits, and is particularly suited to the treatment of low grade sources. And, in the case of waste dump leaching, there is a tremendous resource in-place that has the mining cost already off the books. This paper updates current US copper solution mining trends. Solution mining systems Schlitt (1980) summarized the characteristics of the principle leach systems in the US. He pointed out that the wide variations in copper deposits make solution mining a more site-specific activity than conventional mining and milling. Heap leaching is usually selected for moderate to high grade ores having a copper mineralization that is amenable to acid leaching (oxides, silicates and certain sulfides). Higher grade ores mined specifically for heap leaching are usually treated to optimize copper extraction, therefore, crushing and some pretreatment (acid curing) may be justified. On the other hand, dump leaching practice usually involves leaching low grade waste rock placed on large dumps as dictated by topography and haulage costs. Mine waste is therefore treated in an uncrushed run-of-mine condition. Finally, in situ leaching is appropriate for either very deep ore bodies or for recovering copper from low grade rock left behind in abandoned pit walls, stopes, and subsidence zones from earlier mining activities. True in-situ solution mining should be defined as the leaching of ore in its original geologic setting. Heap leaching Heap leaching has a long history as a hydrometallurgical process for copper recovery. The methodology of heap leaching established at Rio Tinto in Spain more than 300 years ago is basically the same as that used today. Processing concepts, such as solution management (sprinklers and leach/rest cycles) and copper

Jan 11, 1986

By W. D. Mayercheck, A. G. Mayton, J. R. Bartels

Abstract-Since 1982, the US Bureau of Mines has inves¬tigated improvements in protection for operators of thin seam shuttle cars. Due to working height restrictions in thin seam mines (<_1.22 m or 48 in.). Federal mine regulations require that canopy protection on shuttle cars he provided only in mines >_1.07 m (42 in.). However, court obtained variances are granted to mines <_1.22 m (48 in). This paper presents ongoing research to design and evaluate a uniquely positioned, ergonomic compartment for a shuttle car that provides the operator with full canopy protection in working heights of 1.02 m (40 in.).

Jan 1, 1989

By Schlanger H. P

A theoretical model for gas outbursts in underground coal mines is as follows. An outburst is the structural failure ofcoal due to excess stress resulting from body forces caused by gas pressure gradients. These body forces influence the stability of a mine face in the same manner that gravitational body forces affect the stability of the roof of a mine. The magnitude ofthese body forces can be appreciated when it is realized that for an average density coal, the gravitational body force is equal in magnitude to the force from a gas flow with a pressure gradient of 14 kPa m-I. Gas pressure gradients and the resultant stresses within a seam can be calculated with numerical methods. Thus, providing the necessary parameters can be measured or estimated, in principle the theory can be applied to compare the outburst risk of various mining arrangements.

Jan 1, 1985

By L. W. Saperstein

Public Law (PL) 95-87 contains explicit demands for land use planning in its reclamation and designation sections. Both sections require recognition of local land use plans; however, they are not well integrated. Accommodation to these planning requirements affords an opportunity to create better links among local land use planners, the state&apos;s permitting authority and designation office, and mine designers. Mining companies should take a more positive interest in local land use plans and in resource inventories. States should consider handing down to local government the responsibility for accepting mine permit applications and designation of unsuitability petitions.

Jan 12, 1983

By W. E. Coughlin, R. L. Faverty, F. H. Lightner

Introduction The intent of this paper is to present the general strategy and method of implementation to achieve a "fast-track" mine development. The major objectives of a "fast-track" or rapid development schedule are to minimize front-end development expenditures and to realize an early cash flow from operations. The Borealis project of Houston International Minerals Corp. (HIMCO) is used as the working example to illustrate the development schedule. Borealis is a 2.3 kt/d (2,500 stpd) gold-silver heap leach operation near Hawthorne, NV, Pre-Feasibility Planning Proper early planning and identification of priority items were necessary to expedite project progress. On April 1, 1978, HIMCO leased the rights to the Borealis prospect and initiated exploration activities almost immediately. Since Borealis was showing excellent potential for mine development, an effort to clear the way environmentally was initiated during the summer of 1979. With the Borealis properties located within the Toiyabe National Forest, the US Forest Service (USFS) was recognized as the "lead" or respon¬sible agency for addressing the environmental issues. Early scoping of the environmental issues by both HIMCO and the USFS allowed HIMCO to take the initiative and address two potentially critical issues-archaeological and biological. Third party consultants, agreed upon by HIMCO and the USFS, were contracted to conduct archaeological and biological surveys. Desert Research Institute of Reno, NV, provided archaeological services, and JFL & Associates of Boulder, CO, provided biological services. These efforts began in the fall of 1979 and continued through the summer of 1980. Conservative Design Criteria By adoption of conservation design criteria, flowsheets and processing data required for detail engineering were firmly established with a minimum of impact on schedule. On Oct. 21, 1980, HIMCO formally initiated a feasibility study to evaluate the Borealis project. Four organizations were contracted for particular scopes of work: • John T. Boyd Co.: Ore reserve estimation, preliminary mine plan, and mine capital and operating cost estimation. • Bechtel Civil and Minerals: Conceptual engineering, processing capital and operating cost estimation. • Hazen Research Inc.: Metallurgical testing. • Sierra Pacific Power: Cost estimation for power supply. Metallurgical testing and conceptual engineering of both heap and agitation leach flowsheets were investigated concurrently. Numerous economic evaluations were conducted for both heap and agitation leaching at varying production capacities. The results indicated a heap leaching flowsheet treating 454 kt/y (500,000 stpy) yielded the best economics and was compatible with the "fast-track" development goal. Conservative design criteria was established to provide operating flexibility and ensure plant productivities. A summary of major design criteria is presented in Table 1. HIMCO assembled the results of the studies of the various consultants along with internally generated studies to produce the feasibility document. The decision to supply 100% equity by HIMCO rather than arrange project financing help to expedite the project. Cooperation Between HIMCO and Regulatory Agencies With cooperation and mutual trust established between HIMCO and regulatory agencies, the time required for environmental permitting was streamlined as much as practical. To expedite the required construction permits, HIMCO proposed to the USFS that HIMCO fund the total cost of an Environmental Assessment Report (EAR) and that issues be addressed at the technical level of an Environmental Impact Statement (EIS). The previous studies on the critical issues of archaeology and biology provided HIMCO with the information to satisfy the proposed approach. Houston International Minerals and the USFS agreed to have Environmental Research and Technology (ERT) of Fort Collins, CO, prepare a draft EAR for the USFS.

Jan 11, 1983

By C. Hosten, K. V. S. Sastry, D. J. Kawulok-Englund

Introduction Since the last decade the iron ore processing industry has undergone drastic changes from supplying screened and natural ores to manufacturing tailored concentrates and pellets. Increased need for the beneficiation of lower grade iron ore deposits and the increased demand for higher grade concentrates necessitate finer grinding of iron ores before concentration. The normal filtration stations used in the past are experiencing difficulties in dewatering the finely ground concentrates to moisture levels acceptable for balling. In addition to finer grinding, applications of complex beneficiation techniques has decreased the filterability of the concentrates and create problems in filtration of iron ore concentrates. An overview of the filtration literature indicates there are few research reports on the dewatering of iron ore concentrate slurries. There exists a need to understand the principles and mechanisms involved in the filtration of iron ore concentrate slurries with a goal of developing more efficient filtration techniques. This paper presents the results from the first phase of our research program that included the development of a reproducible benchscale filtration technique and the investigation of the filtration behavior of eight iron ore concentrates.

Jan 10, 1983

By G. P. White, J. M. Jones

Computer simtiation is a technique that has beers around for many years. Its applications include designing steel mills, planning space shota, or even developing ways to beat the casinos in Las Vegas. However, the use of computer sirndation in surface coal mining is fairly recent. To promote its use, several government agencies, including the US Bureau of Mines, Forest Service, and Department of Energy, contracted with universities and private companies to develop computer simulation programs for surface coal mining. Some of these developers include McDonnell-Douglas Electronics Co., Pennsylvania State University, Montana State University, Fluor Mining and

Jan 9, 1984

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [ ] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m%-sec instead of meters. Adding the gravitational constant corrects this: [ ] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per sec). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [ ] References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters&apos; Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 3, 1985

By E. S. Erickson, R. L. Stone

Introduction Evidence from blast furnace operations has indicated that using pellets with a higher ISO low temperature reducibility, a lower SiO2 content, and better resistance to low temperature degradation results in considerable coke savings and improved furnace operation. Although these benefits could not be directly related to reducibility differences alone, we believed there was sufficient evidence of the advantages in improved pellet reducibility to warrant laboratory investigation of ways and means to effect such improvements. It is well known that pellet reducibility can be significantly altered by changes in the basicity and the amount of non-iron oxide constituents. Past work (Friel and Erickson, 1980, 1982; Saeki et al., 1977; Thanning, 1974) has shown that with increased MgO contents, and at optimum CaO/S1O2 ratios, significant improvement in low temperature reducibility can be attained. The improved properties of such fluxed pellets have reportedly led to increased blast furnace efficiency and productivity (Saeki et al., 1977; Ilmoni, 1975). Less well known, however, is exactly what factors control reducibility in acid pellets. Because of this gap in knowledge, studies were undertaken of the factors affecting reducibility in acid pellets and to estimate their relative significances in modifying reduction behavior. This paper describes that part of our work done to determine the effect of bentonite on reduction behavior. Our approach was to first examine the effect of bentonite&apos;s presence on as pure an iron oxide as possible (i.e., a magnetite "superconcentrate" containing about 0.2% SiO2) so as to eliminate any gangue-binder interaction. The next step was to look at bentonite effects on concentrates with only limited amounts of gangue (containing about 1% SiO2), but of two different types, simple and complex silicates. Last, we

Jan 1, 1988

By R. W. Smith, Z. Sadowski

INTRODUCTION Problems encountered in barite flotation from various waste materials such as spent drilling muds are likely to be closely connected with the effect of contaminant metal ions and other chemicals on the flotation. Investigations on the recovery of barite from tailings ponds and mining wastes (Sullivan and Lamot, 1981) have shown that such barite materials can contain large quantities of carbonate and silicate minerals (including clay minerals). Also iron oxide slimes can be present. From these substances, cations such as Ca2+, Mg2+, Fe2+, and A13+ can potentially dissolve and be present in the aqueous phase accompanying the various minerals. These ions and their hydrolysis products can have a substantial effect on any subsequent flotation scheme. The present study investigates the effect of the noted ions on both the stability and electrokinetic behavior of barite suspensions. Some adsorption (abstraction) experiments were also performed. Experimental materials and methods The barite used was a high-purity, naturally occur¬ring mineral sample (Kings Creek, SC). The material was ground in a porcelain mill and a fine fraction (mean particle size 11.49 µm) separated out by air elutriation. The mean size was determined by an aqueous sedimentation method using a CAHN electro-balance. In the method, an 0.6-g sample of the barite was dispersed in 450 cm3 of pH 7 water containing 0.01 g of sodium tripolyphosphate. The mean particle size was denoted X0. The stability of the barite suspensions was determined by a comparison of the mean size of the investigated barite suspension aggregations with the mean size of barite powder determined in the presence of sodium tripolyphosphate. The mean sizes (X) of the barite aggregations were determined using the same amount of water and barite sample as in the measurements of dispersed barite particle size but without the presence of polyphosphate. The ratio X/Xo is thus a measure of the stability of a suspension (the greater the ratio, the less stable the suspension). The adsorption (abstraction) experiments were carried out in polyethylene bottles containing 1 g of barite powder in 200 mL of solution. The solids were added to a solution containing a known concentration of metal chloride salts (AlCl3, FeCl2, MgCl2, and CaCl2) . The pH was controlled by both HCl and NaOH addition. The suspensions were agitated in a shaker for three hours. The final ion concentrations in solution were determined by atomic absorption analysis. The electrokinetic measurements were made using a Komline-Sanderson Zeta Reader in a conventional manner. All experiments were carried out in the presence of 1.0x10-3 k.mol/m3 NaClO4. Experimental results Figure 1 shows the zeta potential of barite particles as a function of pH in the presence of iron(II). The

Jan 1, 1988

By Josef K. Alter

Crosshole Sonic Logging (CSL) of drilled shafts requires 1.5-in (38-mm) or 2-in (51-mm) I.D. sonic access tubes to be installed inside the steel reinforcement cage. The sonic access tubes do not contribute to the structural capacity of the drilled shaft. The proposed use of Ischebeck TITAN T73/56 CSL/Hollow Threaded Rebar for Cross Hole Sonic Logging Access Tubes Combined with Longitudinal Concrete Reinforcing in Drilled Shafts (patent pending) is discussed as an alternative method of construction and CSL probe access. The T73/56 hollow threaded rebar/sonic access tube performs as a high strength rebar while at the same time creating a 2.2-in (56-mm) I.D. sonic access tube. The deformed high strength hollow bar provides better adhesion to concrete thus reducing the problem of debonding associated with smooth PVC and steel pipe. A cost comparison using conventional rebar with added sonic access tubes is discussed. The use of T73/56 CSL/Hollow Threaded Rebar as a value engineering alternative can reduce both material and labor costs for drilled shaft construction and can provide an advantage where anchor bolt cages and longitudinal reinforcing create congestion.

Jan 1, 2011

By J. J. Snodgrass

Faults, sandstone channels, and abandoned mine workings present severe safety hazards, disrupt mining, and necessitate costly precautions or discontinuance of operations. In addition to fault detection, mining companies have a need to map discontinuities such as seam thinning and previously mined areas in both longwall and room-and-pillar operations. Initial field tests demonstrated successful generation and propagation of higher order guided wave modes. Theoretical studies indicate potential for improved resolution by sensing small details in the coal seam and roof structure. Controlled-waveform source transducers and specialized detectors are particularly useful to preferentially excite and detect the Love (SH) and Rayleigh-type (P-SV) waves, including the higher frequency modes. The distinct observation of reflections using the transducers in the shear wave mode makes feasible the detection of the water-filled voids.

Jan 4, 1985

By P. R. Dugan

Sulfur removal from high sulfur coal has several objectives including: a) reduction of the atmospheric load that contributes to the problem of acid precipitation; b) reduction of ash, which contributes to decreased energy transfer in boilers, as well as ash disposal; and c) alleviation of the social and economic dislocations reluted to uneven geographical distribution of sulfur in coal reserves. Cost in relation to the value of refined coal will govern the development of an emerging coal refining industry. Estimation of the premium paid by power companies for coal with a low sulfur content is a good estimate of the value that will be added as the result of refining. Estimates of premiums paid in 1984 are $28.65/t ($26 per st) for reduction of total sulfur from 3’% to 1% S and greater than $28.65/t ($26 per st) for removal below 1% sulfur.

Jan 8, 1987

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By Wu Xueling

9K medium was used to isolate iron-oxidizing bacteria from 27 sump water samples collected from Dexing Cop-per Mine, Chengmen Mountain Mine and Yin Mountain Mine, Jiangxi Province, China. Lead acetate and silver nitrate were used to enrich metal-resistant iron-oxidizing bacteria from the above water samples. Isolate 16 was isolated from the sample taken at Dexing Copper Mine. Growth experiments indicated that when incubated under lead acetate (3,500 mg/L), isolate 16 still carried out ferrous ion oxidation, while isolate H1, a less resistant strain taken at Yin Mountain Mine, had a tolerance level of only 400 mg/L. When assayed with other metals, i.e., Ag+ (240 mg/L), Hg2+ (0.9 mg/L), Cu2+ (32,000 mg/L) and Mg2+ (22,500 mg/L), isolate 16 still carried out ferrous ion oxidation while, on the other hand, isolate H1 exhibited much lower tolerance levels, i.e., Ag+ (60 mg/L), Hg2+ (0.1 mg/L), Cu2+ (19,000 mg/L) and Mg2+ (13,500 mg/L). Based on 16S rDNA sequence data, isolate 16 and H1 were both identified as Acidithiobacillus ferrooxidans.

Jan 1, 2007

By Timothy C. Siegel

Given that piles are composed of different materials and installed using a variety of methods, ASTM D 1143/D 1143M-07 Standard Test Methods for Deep Foundations Under Static Axial Compression is justifiably general so that it has as many applications as reasonably possible. There are aspects of the test setup, the test procedures, and data interpretation for instrumented piles (some of which are specific to augered cast-in-place piles) that are either not discussed in detail in this ASTM standard or are not addressed at all. Specifically, the use of variable time hold times can obscure the shape of the conventional load-deflection curve, as well as, influence the interpretation of the ultimate pile capacity. Unload-reload cycles induce additional non-uniform internal axial loads within the pile which complicate interpretation of the strain gage data and increase the potential for errors. Attempts to maintain a constant top load during the hold period can lead to operational difficulties in taking measurements and are technically unnecessary. Residual load has been shown to develop in cast-in-place piles and can significantly influence the axial load distribution as interpreted from strain gage data. The stiffness of cast-in-place piles has been observed to vary with the measured strain, and a constant modulus, as provided by correlation with the unconfined compressive strength of the grout, may lead to a significantly different interpretation of the axial load distribution.

Jan 1, 2010

By R. L. Grayson, G. Mishra

Introduction Many old underground mines have been developed extensively into reserves requiring large numbers of workers to maintain and rehabilitate lengthy track haulages and/or belt conveyor systems. Often, large numbers of fans are required to maintain minimal airflows in areas where poor conditions and huge leakages prevail. Problems that beset one such coal mine and projects undertaken to restore it to potential profitability are presented. Brief history The Vesta No. 5 mine was opened in 1908. Drift development began near the Monongahela River, which was the primary avenue for shipping metallurgical coal to coke ovens in Pittsburgh. Over the ensuing 75 years, the main haulage entries were developed a distance of 16.1 km (10 miles) to the present mining area. Track haulage was used to transport coal from working sections to the river loading facility. As haulage distance and areas of high water influx increased, management decided, in 1973, to construct an underground conveyor belt system. The project spanned 36 months and culminated in a system of 22 flights, ranging from 205.7 to 1767.8 m (675 to 5800 ft) long. Six intake and eight return entries were developed as the mains were advanced. These entries provided adequate ventilating capacity over the years, but as extensive gob areas progressed and roof conditions deteriorated, the entries became inaccessible and more resistant to airflow. By 1981, five fans were being used to circulate 943.9 m3/s (555.5 cfm) of air through the mine. An average of 6440 t (7100 st) were produced from 20.8 continuous miner unit shifts and 2.7 longwall unit shifts each day in 1981. The ratio of support to production personnel was 1.94. To maintain the outby 16.1 km (10 miles) of haulage, 110 personnel were used. The average cost per ton was $43.54 ($39.58 per st), resulting in excessive bottom-line losses. The mine possessed a rather promising reserve, mostly in lease, of good quality, medium-sulfur metallurgical coal, but it also had a number of formidable operating problems. Operating problems Contributing factors toward relatively low productivity and high costs were the conditions of the track haulage, conveyor, and ventilation systems. Productivity was affected greatly by downtime associated with the conveyor system, which lacked adequate access for making splices or other repairs. Many areas within the conveyor belt entry itself required more

Jan 3, 1987