Search Documents

Several Approaches to Enhance the Bioleaching of Enargite Some approaches were investigated to enhance the recovery of Cu from enargite by bioleaching with Acidithiobacillus ferrooxidans using the galvanic interaction with pyrite and activated carbon, and with thermophilic bacteria, Acidianus brierleyi. Addition of pyrite initially enhanced Cu leaching by the Galvanic effect, but after that the formation of secondary minerals passivated the surface of enargite in inoculated batches. Activated carbon improved Cu recovery from enargite much better than pyrite, when it is contacted with enargite. Recovery of Cu from enargite has been recorded to at largest 2.4 per cent within 30 days in the presence of activated carbon when mesophilic bacteria were inoculated at 25¦C. The recovery of Cu from enargite was drastically enhanced by inoculation of thermophilic bacteria, Acidianus brierleyi, up to 60 per cent within 40 days at 70¦C and still not leveled off after 40 days unless the formation of Fe(III) precipitates occurred. After 40 days dissolved molar ratio of Cu/As is around 5.2, suggesting that metal-deficient sulfides and/or ferric arsenate might be formed on the surface of enargite.

Sep 13, 2010

China has made great progress in thick coal seam mining, commonly characterized by longwall top-coal caving mining and single-pass longwall mining with a large cutting height. At present, the maximum mining thickness of longwall top-coal caving reaches 20 m while that of single-pass longwall mining approaches 8.8 m. The top-coal caving–related technologies have significantly improved the mining efficiency of thick coal seams and have also made a great contribution to the centralized underground mining of coal. Thus, the number of underground coal mines is greatly reduced in China. However, due to the increase of the mining height and the changes in mining operations, the overburden movement caused by the mining of thick coal seams is more intense, and the influence scope is larger, which brings a series of new problems on ground control of longwall faces. In order to enhance ground control and improve the mining efficiency of thick coal seams

Jul 28, 2020

By J. Launay

In order to control and dispatch the sewage water coming from 3 tunnels toward 2 downstream sewage tunnels, a large cavern has been excavated in a suburb of PARIS. Located at a depth of 47,00 m, it has been excavated using the NATM procedure through swelling clay, weathered sandstone, and marl and chalk. It is 16,50 m high, 12,40 m wide and 60, 00 m long, with an elliptical cross-section and its two ends are egg-shapped. The final lining of the cavern is composed of 30 to 40 cm of shotcrete, steel ribs and passive anchor bars. The excavation stages and related movements were surveyed by extensometers, pressure cells and convergence devices. The design, method of construction of the cavern and the results of the measurements made are commented.

Jan 1, 1989

To investigate mine ventilation problems which do not lend themselves to conventional anemometer and smoke study techniques by use of SF6 (sulfur hexafluoride) tracer gas. Approach SF6 tracer gas is released in-to the air at a given mine location. By collecting air samples at various other locations and analyzing these samples for SF6, the amount of air traveling from the release location to each sampling location can be quantitatively determined. Travel time between these locations can also be deter-mined. How It Works SF6 is ideal as a mine tracer gas. It is safe, odorless, chemically and thermally stable, and it generally has no background concentration. Furthermore, it is instrument detectable at concentrations as low as 10 parts per trillion. The SF6 is generally released from a pressurized lecture bottle, and air samples are taken in syringes or evacuated bottles. During the past several years, SF6 tracer gas has been employed to study a wide variety of mine ventilation problems such as: recirculation of return air into In-take airways, air leakage from adjacent mines and gob areas, air transit times through stoped areas, airflow patterns during a mine fire, leakage of gases from an underground oil shale retort into mine workings, face area ventilation patterns, methane flows in metal/nonmetal mines following a methane out-burst, and many other problem areas. Examples of some recent uses of SF6 follow.

Jan 1, 1982

By Scott A. Walker, Frank L. Rollo

"The San Francisco Museum of Modern Art (SFMOMA) in downtown metropolitan San Francisco, California, is supported on a mat foundation. Although the mat foundation of the original museum was designed to accommodate a future expansion, the plans for expansion that developed in 2010 required a larger footprint to accommodate the new space requirements of the museum. The new, larger expansion was designed by lead architect Snohetta. It will be a tall 12-story, steel-framed building occupying an area that was once the eastern part of the existing museum as well as two adjacent and newly acquired parcels.As designed, the expansion includes a 30-foot-deep excavation which is surrounded by adjacent buildings and improvements. Because of variable subsurface conditions at the site, geotechnical challenges included mitigating anticipated differential settlement between the existing and new foundations, preventing overstressing of the existing mat foundation, controlling groundwater to prevent settlement of surrounding improvements, and providing temporary support of adjacent structures during excavation for the new basement.To address several of the geotechnical challenges, soil-cement mixed (SMX) ground improvement was recommended by Treadwell & Rollo. However, during contract negotiations and construction, the specialty contractor proposed using jet grouting as an alternative technique for ground improvement. The jet grouting approach was accepted in principal, but when implemented was only marginally successful. Accordingly, the contractor eventually installed SMX panels using a Cutter Soil Mixing (CSM) machine. Because the CSM machine was a late arrival during construction, the contractor was not able to take advantage of the ground-improvement technique to install many of the shoring elements that we had originally recommended (such as the cut-off shoring wall). In the end, SMX panels were installed as ground-improvement beneath the new mat foundation to (1) reduce the potential for liquefaction in clean sand below the groundwater by providing increased rigidity to the soil, (2) reduce the potential for disturbing a weak underlying marsh deposit during construction, and (3) transfer vertical building loads to a layer of underlying dense sand.This paper also discusses the quality control and quality assurance programs that were implemented to check that the ground-improvement techniques used were thorough and complete and provided the required strength to transfer the new foundation loads to the underlying strata."

Jan 1, 2014

By Sotiris Psomas, Colin M. Eddie

"Steel Fibre Reinforced Concrete (SFRC) Segmental Tunnel Linings have successfully been used for over 20 years in the UK and have been adopted in a number of high profile projects such as High Speed 1, Crossrail, Thames Tideway, as well as High Speed 2. Tunnel linings and especially SFRC design are not covered in the Eurocodes. This shortage of SFRC tunnel design rules seems to be partially addressed by several international publications. However, in the UK, the ‘design-assisted by testing’ (DAT) approach has also been adopted. The Paper discusses the UK’s best design practice and focuses on the DAT methodology as applied in the case of the 6.9km (4.3miles), 7.8m (25.6 feet) ID Lining for the £635million Lee Tunnel Project. The design approach, the full scale testing at the Building Research Establishment (BRE), and the construction innovations are presented. This experience will be transferred to the £4billion Thames Tideway Tunnel.INTRODUCTIONSteel Fibre Reinforced Concrete (SFRC) has been used for Tunnel segments for more than 20 years. The first application of SFRC in the UK was for the Heathrow Baggage tunnel (1994). Since then significant size tunnels have been designed and constructed, such as the Jubilee Line (1999) High Speed 1 (CTRL, 2006), Crossrail (2014), Lee Tunnel (2014) and the scheduled 25km Thames Tideway (‘Super Sewer’) and High Speed 2 rail tunnels. However one the main obstacles in achieving streamlined design and improving efficiency are the lack of appropriate design guidelines for SFRC tunnel segments. This issue will – to some extent – be addressed by a number of current documents on tunnel FRC design either being produced by BSi (PAS8810, expected 2016), ACI (544.R) and ITAtech (Design Guideline PCFRC, 2015) in an effort to advance the design of SFRC and take into consideration the recent developments in Steel and Macro-Synthetic FRC technology."

Jan 1, 2016

By Jack J. Ayotte, Michael R. Nadon

"Today's demand for better and more efficient methods inspires new approaches to construction and mine development.A project at Asarco's Aquarius Mine provided a challenge that resulted in the adaptation of a civil construction technique to a mining application.This paper describes the construction of an escapeway shaft to surface from the mine's 150m level. The prime consideration was to provide the most cost-effective method of establishing a shaft collar in the 145 ft (44 m) of water-bearing overburden. This problem was resolved with the employment of the drilled in-caisson method.The remainder of the 500ft (152m) deep shaft was raise bored and portable hoisting equipment was used to install a permanentmanway and shaft liner.IntroductionHaving completed the first phase of exploration development in 1982, J.S. Redpath Limited was engaged to carry out an engineering and cost study to investigate the feasibility of re-opening Asarco's Aquarius Mine near Timmins, Ontario. The scheme was to develop the proven ore reserves and proceed with shrinkage stoping while carrying out further exploration development and diamond drilling.One significant and costly component of the project was the provision of an escapeway shaft to supply additional ventilation as well as a second means of egress from the mine. The major complication to this task was the presence of 145 ft (44 m) of water-bearing overburden at the site. The first and obvious approach was to use conventional ground-freezing methods as had been employed previously on .this property for the initial development shaft. This being the only ""sure"" method available at the time of the budget estimate, it was used as a basis for the study but its considerable projected cost and time demand inspired further investigation into other possible solutions.After considerable research and several brainstorming sessions, a Redpath team came up with an approach whose basic procedures had been used extensively in the civil construction field, although they were novel to the mining industry."

Jan 1, 1987

By J Graaf, R A. Murrell

Gold Fields Australia is constructing two major ventilation shafts at the Wallaby gold mine in Western Australia. The new ventilation shafts are required to facilitate the long term ventilation strategy for the mine, thereby allowing continued extraction of ore beyond 1000 m below the surface. The construction work has involved all of the challenges that shaft construction can throw up, including challenging geotechnical conditions, unexpected high water inflows and major circulation loss during pilot hole drilling for raise boring. An extensive geotechnical and hydrological investigation program was undertaken prior to awarding the shaft construction contracts. While most of the risks were identified, several proved to be much more challenging than expected. The shaft construction methods included conventional sinking into the fresh rock profile in each shaft, followed by raise bore pilot hole drilling and reaming. A headframe was constructed for the first shaft, which was sunk to 92 m with a stage suspended in the shaft to facilitate the concrete lining and provide rope guides for the kibble winding. Drawing from experience when sinking the first shaft, additional ground pre-conditioning was implemented for the second shaft, which was pre-supported with continuous piles to 28 m followed by sinking to 50 m using a crane instead of winders and a headframe. Following the conventional sinking through the weathered zone in each shaft, the shafts were completed using a raise bore. The first shaft utilised a riser pipe and rotary vertical drilling system (RVDS) with the second shaft having utilised a dual rotary rig for pilot hole drilling. This paper reviews the site investigations undertaken, construction methodologies applied, the results achieved and the lessons learnt.CITATION:Murrell, R A and Graaf, J, 2017. Shaft construction at the Gold Fields Wallaby mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 321–334 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

By Issa S. Oweis

Limestone is a sedimentary rock composed primarily of calcite (calcium carbonate). In the presence of an aqueous solution of carbon dioxide (carbonic acid) bicarbonate radicals (2HCO3)- are produced that are highly soluble. The same type of reactions occur in terrains where dolomite (calcium magnesium bicarbonate) reacts with carbonic acid to produce highly soluble bicarbonates (4HCO3)-. The source of carbon dioxide is the small content in rainfall but to a large extent from the organics in the soil. The solution activity depends on many factors including the content of carbon in the rock, acidity of soil water, groundwater velocity and other factors. The resulting features are referred to in literature as sinkholes, solution channels, caves, karstic topography, and cavernous limestone. The presence of solution features affect the shafts in several ways: (a) the shaft resistance is affected by voids along the shaft, (b) concreting of the shaft should consider the presence of voids along the shaft, and (c) the shaft base may be in close proximity to a solution feature that may cause future collapse under structural loads. Methods to mitigate such effects include verification of rock to below the base (vertically and laterally). Cavities are stable by virtue of arching in the rock. Under the action of end bearing from a shaft, the arch may collapse depending on its proximity to the base of the shaft and the strength of the rock. This paper focuses on this issue. Finite Element analyses are conducted to relate shaft end load and bearing area that will produce failure based on given rock properties, size and location of cavity. Failure is defined as settlement of the base equivalent to 5% of shaft socket diameter. The software Plaxis is used for analysis. The rock is considered as c-f material derived based on Hoek-Brown failure criteria (2002 edition) that is based on Geological Strength Index (GSI).

Jan 1, 2009

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

By F. N. F. le Roux

This paper describes the method used for excavating the upper 33m of emergency access shaft E2 for the underground single track tunnel running between Park and Rosebank station of the Gautrain Rapid Rail System. The soil was decomposed shale and diabase from the Witwatersrand Supergroup. The location was in the car park of The Wilds (a public park) in Johannesburg. The method proved very simple and required less complex plant and equipment than normal when excavating the shallow soil sections in shafts. It involves driving steel sheets ahead of the shaft sump into the soils and then excavating inside the ?tub? created by the sheets whilst supporting the sheets above with regularly spaced circular Steel Rings. It is the intent of this paper to discuss the method and design approach to the method. This will be done at the hand of experiences at E2 shaft..

Jan 1, 2009

This paper describes the excavation of No. 1 Power Station Lift Shaft at the Kiewa Hydro-Electric Project. The advantages and limitations of the borehole method are outlined, and general principles of plant design are discussed.INTRODUCTIONFor many years, attempts have been made to reduce mine development costs by various methods. Some of the, techniques of tunnelling have been adopted in horizontal headings, and in main vertical shafts, mechanical plant has displaced hand labour with notable success. However, in the field of small rises and winzes, improvements have largely been effected by attention to details of procedure. The most promising avenues for' substantial reductions in cost relate to:(a) Long-hole drilling(b) The borehole method(c) Calyx drilling.Whilst each of these methods has its peculiar advantages, the borehole rising method is probably most useful, and capable of wide application.In brief, the borehole method of rising requires a, drill hole parallel to the axis of the rise. A hoisting rope is passed through the borehole, and is attached to a platform on which the rising crew are raised with their equipment to the drilling position in the rise.When properly planned, the method is particularly safe, and has generally received the approval of mine inspectors and safety authorities. Rising work is generally hazardous, even when special timbering methods are used. In...

Jan 1, 1959

1. Scope of project In South Australia, the Western Mining Corporation operates the underground copper and uranium mine Olympic Dam. The deposits concerned are enormous (approx. 570 million tons) and have been mined since 1988. At the end of 1996, Western Mining decided to increase the capacity of Olympic Dam from 85,000 t.p.a. to 200,000 t.p.a. Planning At this point, SIEMAG-GHH Mining Division was asked to carry out a study including the planning of the entire shaft hoisting operations and calculation of the investment and operating costs involved. With the assistance of Australian partners, the study was completed within a single month. The principal points of the study were as follows: ? Planning of the hoisting machinery for 1,375 tons per hour from the surge bin below ground to the discharge bunker above ground. ? Optimisation of the hoisting operation with regard to maximum availability and safety. ? Optimisation of the time schedule to minimise the financing costs of the investment. ? Statement of the investment and operating costs. ? Comparison of the technical data, design and availability of the planned machinery with reference plants. Construction of the plant Following acceptance of the study, the decision was taken within a few weeks to implement it. SIEMAG Transplan GmbH received the order to execute the entire shaft hoisting machinery on the basis of the study submitted. The decisive factors in placing the order were: ? Convincing study, adherence to schedule ? Reference to comparable plants elsewhere ? Reference with regard to availability.

May 1, 2003

Shaft sinking through an amphibolite-granite rock mass experienced rock bursts on the shaft walls and benches. However, rock burst phenomena was exhibited only in granite, which is e1asto-brittle with ability to store strain energy caused by orogenic and man made stresses. To improve ground conditions, blasting of destressing holes at shaft corners was carried out. By this technique rock burst during shaft sinking was minimized, but not eliminated.

Jan 1, 1982

By T. Majcherczyk

Shaft lining reinforcing analysis of two shafts under construction has been presented in this study. The first shaft was driven from the surface, while the second was deepened. Mining and geological conditions have been studied with respect to the lining capacity. The improvement of shaft stability comprised two elements, i.e. reinforcement of the shaft lining capacity and improvement of the strength properties of the rock mass. In both tested cases, the particular hazard was connected with non uniform loadings of the lining, which could generate shearing stresses within lining structure. Thus such elements as armored concrete with high strength properties, bolting and injection sealing of the rock mass, and the use of special ring reinforcing the shaft lining have been used in order to reinforce the shaft-rock mass system. Practical conclusions related with new technological solutions, allowing the rock mass and shaft lining reinforcement, have been included for the present study. Practical conclusions related with new technological solutions, allowing for rock mass and shaft lining reinforcement, have been also included to the present study.

Aug 1, 2013

In the plumbing of vertical shafts the methods employed and equipment used, are generally made to best suit existing conditions. Undoubtedly, there is no method that can be called standard or that can be used with equal ease and success on all shafts. At the Mount Isa Mines Limited property in Northern Queensland, Australia, local conditions have presented no major difficulties to be overcome in shaft plumbing work. In fact, compared to those at many shafts, the problem has been rather simple. There are three vertical shafts connecting main mine workings, with the greatest plumbing depth for any single lift, 350 ft.Other conditions pertaining to plumbing work have been generally normal.The method we have employed is, in principle, similar to the Weisbach orientation method with a variation that does not necessitate damping of the wires to bring them to rest. Although conditions encountered have not been such that damping the wires would have been inconvenient, we feel we have saved much time and eliminated unnecessary...

Jan 1, 1940

Since the discovery of coal of the Southern coalfield (Illawarra 1797, Burragorang 1806) coal mining has grown progressively to the thriving industry of today. Early shallow escarpment mining required no serious access development, but with extension of mining to further and deeper areas, sinking became necess- ary. Now, with 17 major shafts and 7 decline drifts in current use, new mining activities involve several current sinking and drifting projects, with more in prospect. Conventional sinking and drifting, using blasting and mucking techniques proven in recent years are normally in use, with attempts, recent and current to accelerate advances by boring techniques. With export and to less extent local market unpredictability, it is vital to produce mine establishment times to allow advantage to be taken of market upswings and there is great need for research and improvement of mine access construction as the major aspect of establish- ment.

Jan 1, 1976

By Doyle P, Mulroney D

The Cassidy Shaft was sunk to access the Mount Charlotte and Reward Orebodies below the Flanagan Fault. The 1,184m deep shaft is concrete lined to 6.5m diameter for its full depth. The initial 590m was excavated by stripping into a 1.8m diameter borehole and hoisting the broken material through the existing mine. The remaining 594m was excavated by conventional shaft sinking methods. The shaft was sunk through 3 existing plats and an additional 8 plats cut. 1,800 tonnes of steel and 8 cables were installed during the furnishing of the 4 compartments.

Jan 1, 1985

By Andreas Prucker

The Greater Vancouver Water District (GVWD) is currently constructing the largest water treatment plant in Canada. As part of this treatment scheme twin water transfer tunnels are being constructed. Work commenced with the 11 m diameter, 185 m deep Seymour Shaft which was excavated by drill and blast using a mobile crane for hoisting. The Seymour Shaft is the first large diameter shaft that has been sunk in Western Canada in recent years. The operational aspects associated with the hoisting, the drill-blast-support cycle and water control in the shaft are the focus of this paper.

Jan 1, 2008