Search Documents

By V. F. Swanson

A mathematical model is presented which allows the free or hindered settling velocity to he calculated for any size or- shape particle in any fluid, and at any percent solids up to the maximum. The validity of the model is supported by comparing calculated velocities (or viscosities) with measured values for 1073 data points contained in 80 sets of data encompassing a range of Reynolds’ numbers, from 0.002 to 770.000. The average error was 0.69%, with an average standard deviation of 6.65%. The derivation of the model is too lengthy to include in this paper, which will specifically present the application of the model to the free settling of minerals and spheres, prediction of the friction factor in wind tunnel tests, the viscosity of suspensions of spheres, the hindered settling of mono-sized spheres and closely sized minerals, and the settling of large spheres in suspensions of small spheres.

Jan 1, 1990

By D. W. Wu, M. T. Haque

A novel impedance probe was commissioned specifically for capturing fast dynamic information about filtration processes. It provides an attractive alternative to more complex measurement techniques in situations where the slurry system is primarily one-dimensional. The probe can monitor mudline, slurry densification and drainage. Dynamic variations in cake permeability are obtained by combining dynamic mudline information obtained with the probe and filtrate rate data derived from a leaf test apparatus. The measurements are reviewed in relation to micro structural measurements obtained on iron ore filter cakes. The practical significance of these measurements for optimization of the filtration process is discussed.

Jan 1, 2002

By T. N. Moore, E. M. De Souza

Vibratory hand-tools can produce Hand Arm Vibration (HAV) Syndrome in their operators. This disease, often called Vibration White Finger, can cause varying levels of hand-arm discomfort and, in severe cases, impairment. In addition to the human suffering, there are also significant economic repercussions for industry. These include reduced operator efficiency, lost time through increased absenteeism and increasing compensation awards. In the mining industry, jackleg rock drills are a particularly troublesome source of hand vibration exposure. As a result, a significant amount of work has focused on redesigning rock drill handles to minimize hand-transmitted vibration. This paper details the results of a study undertaken to determine the effectiveness of using elastomer covered ("cushioned") handles in place of the standard steel design. The results indicate that, for a particular cushioned design, the overall acceleration level experienced at the hand-handle interface can be reduced by as much as a factor of three, relative to the steel handle. It is also shown that this reduction takes place predominantly in the frequency range above 500 Hz, with performance improving with increasing frequency. Qualitative evaluation of the cushioned handles by the drill operator indicates a significant increase in comfort over the standard steel handle.

Jan 1, 1992

By Steven Atkin, Rens Verburg, Bryony Hansen, David McWharter

The use of paste tailings as underground backfill and for surface disposal is rapidly expanding, and with it comes the requirement to understand and predict its long-term environmental stability. This paper presents the results from a kinetic testing study performed on cemented tailings paste mixtures under both subaqueous and subaerial conditions. In addition, the effects of grainsize reduction are investigated. It will be demonstrated that the long-term weathering behavior of tailings paste is controlled by its physical and chemical characteristics, as well as its placement conditions. The testing indicates that subaqueous disposal of paste inhibits acid generation, whereas the exposed samples produced acidic leachate despite the presence of cement added to meet geotechnical requirements.

Jan 1, 2000

By D. Malhotra, R. M. Hoover

The effect of a surfactant, designated Syntex, on the wetting and spreading of hydrocarbon oil on molybdenite surfaces (faces) has been investigated experimentally through measurements of zeta potentials and factorially designed flotation tests. These studies indicate that Syntex has a positive effect in increasing molybdenite recovery in the rougher flotation circuit at the Climax mill. The analysis of experimental data using DLVO theory shows that the controlling factor in determining the magnitude of the repulsive energy barrier preventing oil from wetting and spreading on the molybdenite faces is the MoS2 zeta potential and the vapor oil droplet size. The role of Syntex in this case seems to be related to the decrease and stabilization of MoS2 zeta potential by Syntex adsorption and also to the emulsifying action of Syntex on vapor oil to provide a more favorable oil particle size.

Jan 1, 1976

By K. N. Han, P. B. Queneau, A. Stojsic, M. J. Collins, V. J. Ketcham, R. M. G. S. Berezowsky, W. D. Vardill

The bulk of the ore found in the Lihir Island deposit is refractory in nature, with the gold contained in auriferous pyrite. In support of an evaluation of the development of this deposit by Kennecott (a wholly owned subsidiary of RTZ) and Niugini Mining Ltd., testwork has been carried out at the Sherritt Research Centre to demonstrate the amenability of the Lihir ore to pressure oxidation pretreatment to liberate the refractory gold. The results of pilot plant treatment of the Lihir ore in a continuous circuit with a feed rate of between 10 and 30 kg/h ore are described. The integrated circuit comprised pressure oxidation, residue washing, and gold recovery from the washed residue by carbon in leach or carbon in pulp cyanide leaching. Significant factors affecting gold recovery included temperature and retention time in the pressure oxidation step, and the concentration of soluble chloride in the feed. Gold extraction from well washed ore, after oxidation at 210°C for 66 minutes in the autoclave, was typically between 94 and 96%, compared with less than 30% by direct cyanidation.

Jan 1, 1993

By Betty L. Gibbs

Before the first shovelful of dirt is removed from a developing mining property, a wide range of data must be collected, organized and analyzed. Among the key steps in this process are: • Visualization of the deposit from drill hole data and geologic interpretation, using all available information, including surface geology, geochemistry and geophysics. • Drawing of vertical and horizontal sections. • Construction of a 3D solid model of the deposit. • Contouring of deposit outlines and geological structure until the model represents best estimate of reality. • Estimation of grade and quality distribution. • Calculation of reserves. • Examination of possible mining methods. • Determination of economic feasibility. Many techniques are available to aid in this process of mine project feasibility analysis, from quick pencil calculations to sophisticated computer methods. However, time races faster in the complex modem business world than it did 50 years ago. Tried and true pencil methods take too much time. Opportunity may pass a mine developer by while a property is still in the first stages of analysis. In the days of hand techniques, initial analysis of the economic feasibility of a mining project usually stopped with reserve calculations and broad mine planning. Further planning was not done or was done only for the short term. Manual techniques require too much time and manpower to evaluate a longterm mining program. Mining-industry recognition of computer utility has increased. Most companies now use computers in technical applications and could not conceive of working without them. Building initial computer models of a deposit may take nearly as long as hand techniques. But the payback comes when changes are needed and a variety of mine plans are quickly tested.

Jan 1, 1990

By Robert A. Jankowski, Ellsworth R. Spencer, Jay F. Colinet

Longwall mining is the most productive method of under- ground coal mining in the United States (US.), and record levels of production have been reached in recent years. These ever-improving production levels have the potential to generate significantly higher quantities of respirable dust. Consequently, the longwall industry continues to struggle with controlling dust liberation and maintaining compliance with the federally-mandated respirable dust standard. In response, longwall operators have in- creased the application of primary dust controls, airflow and water flow, in an effort to improve respirable dust control and reduce worker exposure. Pittsburgh Research Center (PRC) personnel conducted dust surveys at 13 longwalls operating throughout the U.S. and collected information to: identify current operating practices on these longwalls, identify the types of dust controls in use, document the levels at which these controls are being applied, and measure the respirable dust levels present. This data was analyzed to quantify the dust levels generated by the major sources on the longwall section and to evaluate the relative effectiveness of the control technologies in use.

Jan 1, 1997

By J. E. Gebhardt, D. W. Fuerstenau

The use of small quantities of polyacrylic acid (PAA) was found to significantly improve the flotation of fine-sized hematite particles at pH 4.1 and 0.001 M NaCl with sodium dodecykulfonate (SDS). Low polymer dosages before collector addition aid flotation by forming flocs of primary particles, but excess polymer results in low flotation yields due to surface saturation by the hydrophilic polymer. Contact angles, measured on a hematite disk, substantiate the hydrophilic nature of an adsorbed polymer film. Pre-adsorbed PAA reduces the amount of SDS adsorbed on the hematite particles, but the flotation of hematite flocs occurs, even at reduced amounts of adsorbed SDS, and is not depressed until PAA dosages in excess of the saturation value are used. Separation of a hematite-quartz mixture can be achieved by SDS flotation of PAA,-flocculated hematite. Maximum selectivity results with the addition of small quantities of PAA, while excess polymer is detrimental to the recovery of hematite. Consecutive flotation states on a single feed yield a higher grade hematite product at some expense to the overall recovery.

Jan 1, 1987

By Irving Hoch

INTRODUCTION The demand for tunnelling can be related to urban population size and density; often, tunnelling occurs when a certain city size and density threshold is reached, and increases thereafter as a function of those population characteristics. Subways for rail mass transit are the most notable example, of course, but tunnels for water supply and perhaps for sewerage can also be related to size and density. As cities grow large they sometimes outgrow their local water supply and have to import water from distant places via tunnels; witness New York City, Los Angeles and San Francisco. And it has been suggested that Chicago use deep tunnels for storm water storage because tertiary treatment to meet water quality standards will require treating storm water runoff.(1) Other uses of underground space also increase with urban density, e.g., underground parking, concourses and shopping centers such as Rockefeller Center in New York City and the Place Ville-Marie in Montreal. These examples can be viewed as illustrative of the central point of urban land economics. As the number of people locating in a place increase, they bid up land values and make the more intensive use of land economic, with land defined to embrace the space both above and below the surface. Hence, we are led to think about the city, and of urban land use, in three dimensions. Now, if we accept the relation of underground space use to urban size and density, recent demographic trends seem anything but hopeful for future tunnelling demand: urban density is declining, population growth is slowing down generally, and there

Jan 1, 1974

By Mark Gershon

Most recent work in the field of mine production scheduling has focused on either the computerization of the traditional methods or the development of sophisticated mathematical optimization models. Yet it is clear to all concerned that the optimizers need to be made more practical and the traditional approach needs to be made more optimal. This paper, along with another recent paper (Gershon, 85) open a middle ground between these two approaches. In that recent paper, a heuristic procedure for production scheduling was introduced. Here, a series of short term optimizations are used in a creative manner to approximate the true long term optimization. Since these small optimizations are aimed at blending to meet production quality specifications, this approach is most applicable to commodities where the blending function is very important such as coal, cement, phosphates or iron, to name a few. The traditional and the optimization approaches are so far apart that their' advocates have difficulty identifying with the other approach. This is especially true concerning the difficulty of understanding the optimization models for those not trained in the field of operations research. This paper takes the position that the pro- 120 per role of the operations researcher is to provide not only useful and advantageous approaches, but practical, understandable and implementable ones as well. This is the goal of the paper in describing a new approach, consistent with the traditional methods and aimed at approximating the results of the optimizers.

Jan 1, 1986

By Manuel Bernales, Aldo Leon, Alexandra Carlier, Bern Klein, Andre Xavier

Mining companies and governments at both the local and national levels recognize that Participatory Environmental Monitoring and Surveillance Committees (PEMSC) are necessary mechanisms for meaningful engagement at the community level. In many cases, PEMSCs are established as volunteer initiatives by mining companies or by the mining communities themselves. In Peru however, they can also be recommended by the government as way to address social conflict. Most PEMSCs are launched while a mine is in operation and have the objective of monitoring both water quality and quantity. Many established committees are currently evolving and adopting a more comprehensive approach, as well as expanding their initial scope from a river or micro-basin focus and watchdog agenda, to a broader regional integrated resources management view. This paper examines the origins of Participatory Environmental Monitoring and Surveillance Committees in Peru. It also discusses the typology of these committees, and the scope of their work. Furthermore, it looks at the challenges faced by these committees, as well as existing opportunities for mining companies, governments, and civil society. Finally, this study presents a governance model that could contribute to the long-term existence of these committees. This discussion is further informed by the results of a national workshop that took place in October 2016 in Peru, in which over 200 representatives from 22 monitoring committees, government and mining companies participated.

Jan 1, 2017

By L. A. Romo, J. A. Ferrer

INTRODUCTION The principle line of the Caracas Metro is located generally along the most important east-west traffic corridor of the city from the yards and shops in Propatria at the western extremity to Petare, and eventually beyond to Palo Verde at the eastern end, a route distance of 21 kilometers. There will be 23 stations along the alignment, underground, at grade and elevated, and the line is forecast to handle 1,209,100 passengers daily by the year 2000 with a travel time of 29 minutes between Propatria and Petare. This principle line was divided into three sections for design purposes: Propatria-Fuerzas Armadas, Section I, Fuerzas Armadas-Chacaito, Section II and Chacaito-Petare, Section III. These sections were further subdivided into subsections for construction purposes. The Venezuelan Government, through its Caracas Metro Office in the Ministry of Public Works, awarded design contracts in sections to PARSONS BRINCKERHOFF-TUDOR-BECHTEL for Propatria-Fuerzas Armadas, Section I, OCOIDESA-GRID-APM for Fuerzas Armadas-Chacaito, Section II and OCOIDESA GRID-APM for Chacaito-Petare, Section III. Construction contracts were awarded by international bidding and work is now underway, by joint venture organizations of Venezuelan and foreign firms. The first two sections are under the administration of a company of Engineer/Inspectors in each section. The construction supervision of contracts in the first section is under the administration of the Venezuelan firm, Gómez-Celis-Herrera, (GCH) Engineers, acting under contract to the new C.A. Metro de Caracas that replaced ' the former Office of the Metro. The Propatria-Fuerzas Armadas section, approximately seven kilometers long, consists in part of the 2,951 linear meters of twin-bore

Jan 1, 1979

By Kevin DeSomber, Scott Bird

Larger grinding mills continue to utilize large gear-driven drives or electrical wraparound drives. The panel will include presenters from operations with large mechanical and electrical drives. JIM HANDLEY: Before we get to the third and final session, I want to introduce my co-conspirator for this session, John Mansanti. John is manager of milling with Newrnont Gold Company, Carlin, Nevada, and was very active in securing participation in this innovative symposium. I'm Jim Handley and I'm with Cyprus-Amax Minerals at the Sierrita copper and molybdenum mine. Our third presentation is titled "Geared Up or Wrapped Up?" I hear this topic discussed, but never at great length. I think that's because the opinions are fairly strong and diverse, and people generally aren't reinforced properly in their arguments. The first person to enlighten us on this topic is Scott Bird. He has more than 20 years with Kennecott, is a graduate in metallurgical engineering from the University of Utah, and is currently operations superintendent and deals with this phenomenon every day.

Jan 1, 1998

By Thomas E. Bruner

Today many small diameter tunnels are being constructed in Metropolitan areas and towns as transmission holes for utilities such as water, electricity, natural gas and sewage, to name a few. These tunnels function as utilities beneath the streets, highways, railways, and other structures where open-cut techniques are impractical for any one of a number of reasons. Many such bores range in diameter from 15 to 72 inches and in lengths from 100 to 500 feet. Auger drills with auger type heads have long been used to bore these "road crossings" as they are usually termed; however, many such crossings must be bored in rock with rock-boring heads. Rock with a compressive strength of 15,000 p.s.i. and higher seems to present the greatest challenge for the contractor. These rocks include most igneous and metamorphic rocks and some sedimentary rocks. In general, this grasps most granites, basalts, gneisses, slates, schists, quartzites, limestones, and cherts. In the past ten years boring machines have been developed and used to excavate road crossings through hard rock. Many crossings have been successfully excavated using these machines, and the degree of success has increased substantially in the last few years. A variety of machines have been built and manufactured to bore most rock in a range of diameters up to 72 inches. The machines vary in capabilities, size ranges, and designs but all perform the same basic task and function of boring horizontally. Incidently, here the term horizontal implies horizontal or within five degrees of horizontal. In addition, there is a wide variety of designs, sizes, and types of drill stems, joints, and pipe to meet the various conditions and

Jan 1, 1974

By J. B. Hiskey

INTRODUCTION The extraction of gold and silver from ores, concentrates, and various metallurgical products can be achieved by a number of hydrometallurgical techniques. The solvation properties of alkali cyanide solutions on gold and silver were recognized 200 years ago. A cyanidation process for leaching gold from its ore was patented in 1887 and 1889 by MacArthur and Forrest. The solvent action of thiosulfate on gold and silver was observed over 100 years ago. Recently, several patents have been issued for processes using ammonium thiosulfate as lixiviant for precious metals, Berezowsky, et. al (1978) and Kerley (1981). Tozawa and and coworkers also examined the dissolution of gold in ammoniacal thiosulfate solution. Thiourea leaching of gold and silver initially discussed by Plaksin and Kozhukhova in 1941 but has received only limited attention since that early work. Use of thiourea as an alternative to cyanide was the topic of several papers presented at the 1981 AIME annual meeting In Chicago, Illinois. Hiskey provided a review of the fundamental chemistry of the dissolution of gold and silver in acidic thiourea solutions. Pyper and Hendrix reported on the leaching of a finely disseminated gold ore using thiourea as a lixiviant. The review article(6) previously presented was fairly comprehensive covering Important contributions to the chemistry of thiourea and the processing of gold and silver with acidic thiourea solutions. A search of the technical literature was made to determine recent (since 1981) progress and developments in applying thiourea to the processing of gold and silver. This review reveals that Soviet and Eastern European scientists are continuing to make major contributions to our understanding of thiourea/precious metal systems.

Jan 1, 1984

By T. R. Ellis

The vast majority of valuations produced for mineral properties using the net present value method provide an estimate of investment value or use value. Such an estimate can be a long way from the price that the property would actually sell for if placed on the market. Indicators from the market need to be used to validate or modify the net present value calculation if market value is being appraised. The comparable sales and replacement cost methods used in the appraisal of urban buildings generally fail when used in the appraisal of mineral properties. Other methods of sales analysis are introduced. Guidelines for what a minerals appraisal report should contain are presented.

Jan 1, 2002

By R. S. Ondrey, R. A. Haney, T Tomb, R. T. Stoltz, Novakowski D. L. Chiz, E. J. Gerbec, D. J. Atchinson

Although the number of operating longwalls in the United States (approximately 100) has remained relatively constant over the last five years, longwall production levels have significantly increased and in some cases more than doubled. As a result of this production increase, control of respirable dust continues to be a problem. Therefore, the Mine Safety and Health Administration (MSHA), Pittsburgh Health Technology Center, Dust Division, initiated a study to investigate the availability and adequacy of technology for controlling dust on longwall mining operations. The study involved 23 longwall mining operations in three different Coal Mine Safety and Health Districts. Each operation was visited for a full shift. Respirable dust samples were collected on face personnel and at fixed locations along the face. Methods being used to control dust were noted, with special emphasis placed on obtaining quantitative data relative to ventilation, headgate dust controls, cutting drum sprays, external machine sprays and cutting sequence. Attempts were made to correlate dust control practices in place at the time of the visit to dust concentrations measured at the tail and on the tail shearer operator and to the average of all the dust concentration measurements from the occupations sampled. The methods used to control dust were also compared to the gamut of methods known to be available. This paper presents a discussion on the effectiveness of the methods being used to control dust and on the availability of technology for the control of dust on longwall mining operations.

Jan 1, 1991

By Betty L. Gibbs

What does the information age mean to mining companies? The perception of greatly increased access to information is based on modern communications through ‘smart’ fax machines and computer networks. Computer media allow us to `talk' to the President or to a sister in Australia. If we need data to help put together a mining permit, we can find that data somewhere on computer media. The vast amount of easily accessible information quickly overwhelms us. To avoid `information burnout,' we must learn to target searches and be able to discriminate between dross and information that is useful to our goals. If you watch commercial TV, you have learned to screen out most product commercials. A similar screening process must be applied to computerized information sources. You may need to sort through a lot of irrelevant information before finding the pearls you are looking for. ‘Smart’ fax machines can send information with no direct human intervention. MINES FaxBac, for example, from the US Bureau of Mines instructs you to enter four-digit numbers to have particular reports sent directly to your fax machine. Software vendors use a similar system to supply information about their products. You select an item by number, and the related brochure is faxed to your machine. To compete, the industry must maintain access to as many information sources as possible. The availability of computers and software for almost every conceivable application allows us to accomplish work faster than we ever thought possible, even as recently as 10 years ago. Most mining companies have become aware that doing geology, reserves, mine planning and other technical tasks completely by hand is much too slow. The world moves faster, drilling happens faster, mining happens faster, all related activities happen faster. We no longer have the manpower or time to keep all maps. calculations and records up to date.

Jan 1, 1994

By Bruno Bussière, Michael Aubertin, Robert P. Chapuis

Covers with capillary barrier effects (CCBE) have been used in recent years as gas barriers for the isolation of wastes, including reactive mine tailings. Capillary barrier effects help to maintain a high degree of saturation in the moisture retaining layer, which then reduces gas flux. Various factors affect the degree of saturation of the moisture retaining layer in a CCBE, such as the material water retention characteristics and layer thickness. Slope geometry can also influence the hydrogeological behaviour of a CCBE, but this factor has frequently been ignored in the past. In this paper, the authors show some results of a numerical study that illustrates the influence of slope on the behavior of capillary barriers made of different types of material. The numerical model calculations are based on an actual case of a CCBE constructed in northern Quebec. This investigation shows that the water content profile is greatly affected by the position along the slope. Thus, it is necessary to evaluate the influence of the geometry to properly establish the performance of a cover system.

Jan 1, 2000