Search Documents

By Randall M. Wheeler

Using Computer software to analyze and interpret blast vibration effects has never been so practical. Fully digital seismographs and powerful desktop and portable computers have led to the development of fast and easy to use analysis software. This workshop will focus on new Microsoft Windows-based blast vibration analysis programs developed by White Industrial Seismology, Inc. The Windows point and click graphical environment is ideal for developing full-featured and yet intuitive software.

Jan 1, 1994

By S. R. B. Cooke, H. S. Choi, I. Iwasaki

In a previous article1 the function of various fatty acids as collectors for iron ores was reported for the two alternate processes; (a) the flotation of iron-oxide minerals, and (b) the flotation of calcium-activated siliceous gangue. The selectivity of separation was shown to be markedly dependent not only on such common parameters as pH and the levels of collector and activator addition, but also on the structure and the degree of unsaturation of the acids used. The iron ores employed consisted primarily of hematite, goethite, and quartz and as the effectiveness of any one acid on the separation depends on the individual response of each constituent mineral toward the given collector, a comprehensive knowledge of the floatability of the individual minerals is desirable for the interpretation of the results obtained. The mechanism by which a collector ion becomes attached to a mineral-solution interface has been a subject of much investigation. From quantitative studies of the properties of the electrical double layer on mercury2 and on several solid surfaces3,4,5,6 , the adsorption of some flotation reagents at the mineral-solution interface is beginning to be understood. For example, it has been demonstrated from streaming potential measurements made on quartz5 and corundum6 that the interfacial electrical condition is strongly dependent on the pH. Thisoccurs presumably through the following electrolytic reaction at the interface, and in the presence of a flotation collector, controls the floatability of the solids. A concurrent investigation of the flotation behavior of goethite and of quartz carried out at the School of Mines and Metallurgy7 has shown a positive correlation with the electrokinetic behavior of these minerals. The purpose of the present investigation was to collect general information on the floatability of hematite, and to investigate the function of various 18-carbon aliphatic acids on the floatability of hematite, goethite, and of activated quartz. Electrophoretic mobility measurements, simplified flotation tests using a modified Hallimond tube, and contact angle and frothability measurements were employed. The results are of direct application in the interpretation of the batch flotation results on natural ores as

Jan 1, 1961

By Thomas W. Camm

This study was done to evaluate the costs of various dumping operations at waste and spoil piles. It has been theorized that accidents associated with dumping operations might be reduced by short-dumping rather than edge-dumping, but many operators have been reluctant to use short-dumping because they believe it is not as cost effective as edge-dumping. To evaluate this perception, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health reviewed the costs of various dumping methods at waste and spoil piles. The study found that overall cost differences between the two methods were not significant in most cases. However, while overall cost differences between the two methods appear small, capital costs could be more significant when short-dumping if numerous dump sites are used concurrently. The choice of which method to use should be based on considerations of the safety of dozer and truck operators.

Jan 1, 2000

By Keith Mayhew

Ante la alta demanda de cobre por el crecimiento urbano e industrial y para la construcción de infraestructuras, la industria del cobre necesita una solución para el desarrollo sustentable de los recursos minerales de cobre con alto contenido de arsénico. En ese sentido, Teck Resources Limited (Teck) y Aurubis AG (Aurubis) están trabajando juntas para desarrollar una tecnología que sea aceptable desde los puntos de vista regulatorio, medioambiental, social y económico. Por ello, el presente trabajo señala los resultados obtenidos por Teck-Aurubis conjuntamente, como consecuencia del programa técnico desarrollado desde 2010 para el tratamiento con éxito de concentrados de cobre con alto contenido de enargita usando la tecnología CESL.

Sep 12, 2011

By Jerry Wallace

This project consisted of blasting for expansion of a major interstate natural gas transmission pipeline pump station. The pump station handled 400-500 million cubic feet (1 l- 14 million cubic meters) of gas per day.

Jan 1, 1996

Recovery of Fine Gold Particles from Philippine Gold Deposits by Enhanced Gravity Concentration and Flotation The objective of the study is to determine the applicability of enhanced gravity concentration (EGC) and flotation for gold recovery. While gravity concentration methods have long been applied to gold ores, especially to free-milling types that requires minimal beneficiation, flotation for gold recovery has not yet taken hold as a major operation in the Philippine setting. In this study, the application of EGC and flotation for gold is applied and compared to the existing methods for gold recovery. Two samples, with assays of 7.315 and 5.333 g Au/MT (samples 1 and 2, respectively) are used for this study. These samples are subjected to mineralogical studies and is found to have a gold-particle size ranging 10 to 200 microns. To verify the separation size, the mesh-of-grind (MOG) is used as the primary parameter for experimentation. Initially, the samples are stage-crushed, ground, and subjected to EGC using a Falcon SB40 Concentrator. Based on the results, the two samples showed that recovery increases with a finer MOG. The ratio of concentration (K) decreases with a finer MOG. This shows that there should be sufficient liberation of the gold values for EGC to be effective. The effect of the enhancement is to pronounce the difference in specific gravity of the minerals, promoting better separation. This is validated by the high recovery values of 86.97 per cent and 98.73 per cent exhibited respectively for samples 1 and 2 (at 54 microns). For the flotation runs, sample 2 with an average particle size of 80 per cent passing 74 microns is examined using thiocarbamate-based collectors for roughing and subsequently exhibited a recovery of 96.32 per cent. At this point, the concentration ratio (K) is noted as an important efficiency indicator for flotation process since it yielded a very low-mass and high-metal content concentrate.

Sep 13, 2010

By D. Harrington

Educational campaigns conducted by the manufacturers of explosives, the Bureau of Mines, mining companies, and safety organizations have contributed greatly in reducing accidents caused by explosives arid blasting. Despite these campaigns and the dissemination of information, accidents from explosives and blasting continue to be the direct cause of scores of fatalities and hundreds of nonfatal accidents annually, not only in the mineral industry but essentially wherever explosives are used. The experience of many mining companies and other users of explosives has proved that accidents from explosives can be prevented or averted by the proper training of employees in the handling and using of explosives and by the enforcement of definite rules and instructions for their use. Unfortunately, throughout the years numerous false impressions and ideas have grown up and around the use of explosives. Many of these can be traced back to the manner in which the users of explosives were originally taught, if instructed at all; and as with many types of misinformation in nearly all walks of life, those false ideas are decidedly persistent and being so cause much damage. Many if not most of the users of explosives gained their knowledge of explosives and blasting by watching others and more or less "absorbing" the procedures and thrones of the other fellow, who acted unconsciously as teacher or instructor. A study of explosives accidents reveals the results of such "teachings" when the causes of the accidents are determined, and as might be expected the results very often are far from good. One of the most persistently erroneous impressions or ideas is concerned with the burning rate of safety fuse. Many men with

Jan 1, 1944

Several glacial episodes have been distinguished in the Shotover Valley. These produced fluvioglacial aggradational deposits downvalley from the terminii, commonly with well-preserved terrace treads, as exemplified near Skippers. Chronological links can be determined between the Shotover tills and sediments and assessed equivalent deposits in the Wakatipu Basin/Kawarau Valley region through axial valley profiling. Constructed relationships suggest older Shotover events were probably large and left little detrital deposits within the valley. In contrast, the younger advances were smaller and valley-constrained. They are modelled as being wholly of Waimea or Otira Glaciation age, advances from the latter period producing the visually distinctive flights of terraceremnants. Both the terraces and the inner gorge, now occupied by the Shotover River, have been extensively worked for alluvial gold. Enrichments in the former environment have predominantly been as bottom or intermediate lags produced during degradation phases of catchment erosion. Surface lags have been locally targeted. Placer mining in terrace areas involved both tunnelling and sluicing techniques. In the modem river the greatest concentrations were on the schist or false bottoms, although flood gold has always contributed to the returns. Placer mining techniques here were highly variable.

Jan 1, 1998

By C. O. Aksoy, H. Kose, K. Heasley, E. Yalçin

"In Turkey, the growing demand for lignite has resulted in increased lignite production and an emphasis on improving underground recovery. This has resulted in a gradual increase in the application of the retreat longwall mining method and also in the extraction of the safety pillars protecting permanent underground structures (drifts, shafts) in mines prior to their abandonment.Extracting these safety pillars presents a special hazard to mine employees and the stability of the mine. Often subjected to high stresses, the behaviour of these pillars is not always predictable. Special care must be taken to ensure that infrastructure does not collapse prematurely, and that working conditions remain safe. Otherwise the extraction must be halted, and the remaining coal lost.This investigation reports on a study of the stability of safety pillars during the final extraction phase of the Hustas mine in Soma, Turkey.” The model construction was based on mine plans, and material properties were derived from physical properties testing. Observed subsidence effects from other mining events were used to calibrate the overburden lamination thickness.The model results compared well with surface physical disturbance occurring as a result of mining, as well as with conventional longwall stress redistribution theory and underground observations. The study has shown that properly calibrated models can be useful in assessing mine safety during remnant pillar extraction. The LAMODEL results demonstrate the convenience of this easy to use software."

Jan 1, 2004

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

The design of excavations in high displacement mining environments requires consideration of both the load and displacement capacity of the ground reinforcement and support systems. This paper is a case study on the design of point anchored rebar bolts using laboratory tests and field trials at the Ridgeway Deeps block cave. A laboratory testing program was carried out to measure the mechanical properties of the Strata Control Systems R27 Secura resin bolt which is currently being installed on the extraction and undercut level at the Ridgeway Deeps block cave. The aim was to quantify elastic, plastic and energy parameters for various bolt, mesh and plate systems. Experiments were performed on bar segments, bolt/plate systems, and bolt/plate/mesh/resin systems. The mechanical properties were calculated from tensile tests with a 500 kN Avery machine. Load-displacement data was collected from four different testing configurations. The laboratory results are compared with underground measurements and observations of bolt performance.

Nov 25, 2010

By Kosuke Hosoda, Shuji Owada, Hiroyuki Tokuichi, Hirobumi Ohta, Chiharu Tokoro, Moto-o Sato, Katsushi Okumura, Hiroto Ogawa, Hideaki Umezawa

The Japanese government enforced the "Small Domestic Appliances (SDAs) Recycling Law" in 2013. The law targets metals such as Ta, Nd, Dy, Co, and W to be recycled. Considerable amounts of these minor rare metals are mounted on printed circuit boards (PCBs) of the SDAs and/or e-scrap (electric and electronic scraps). Although precious metals and copper can be recovered from the e-scrap in non-ferrous metals smelters, most of the minor rare metals report to the slag in these smelters in non-recoverable forms. These metals are often used in particular types of devices, and therefore it is possible to concentrate them by separating such devices before feeding to the smelters. In previous work we developed technology for "Device Separation" to concentrate several minor rare metals, but some problems remained, such as how to remove the PCBs from e-scrap bodies, and how to detach devices from PCBs after their removal from escrap bodies. This paper proposes a two-stage crushing process in which, firstly, PCBs are removed from the e-scrap body with various crushers, and secondly, devices are detached from the PCBs involving the application of elevated temperatures. It was found that in the first stage, crushers with physically flexible rotating media such as chains, which provide high collision probability with the sample and consume relatively low energy, can quite effectively separate the PCBs from the e-scrap bodies non-destructively. In the second stage, heating was found to be remarkably effective in helping to detach mounted devices from PCBs, also non-destructively. This paper will also discuss the detailed mechanism of the heating effect on the detachment of devices from PCBs.

Jan 1, 2014

By Joseph L. Condon

Fifteen shots of three explosives with charge weights of 0.52, 1.1, 3.1, and 5.1 kilograms were fired in a pond to study the seismic effects of detonating explosives in water. Shock pressures and bubble periods were measured with pressure transducers in the water. Vibrations were measured on land in three orthogonal directions with particle velocity gages. Statistical tests indicated that a charge weight exponent of 0.43 best scaled the data. While shock pressures and bubble periods showed considerable differences in explosive performances, the amplitudes of ground vibrations showed less difference, and one prediction equation was therefore derived to estimate vibration amplitudes from all the explosives.

Jan 1, 1970

By Manish Uttarwar, Rajendra Yerpude

India is the third largest producer of coal and the fourth largest in terms of coal reserves in the world. However, new research quite ironically projects that despite the continuing growth in domestic coal production, the country’s exploding economic growth will position it to be the biggest coal importer by 2020. India’s inability to meet the domestic coal demand is mainly attributed to low rate of production, increasing stripping ratio, non use of appropriate technology etc. of coal mining operations here. Presently Indian surface mines which have to shoulder the onerous responsibility of augmenting the coal extraction rate at an even brisker pace are mulling bigger, better and more efficient operations ensuring commensurate rise in stripping work as well. This mammoth task can be accomplished only by deploying smart technologies. In this perspective, cast blasting of overburden emerges on the horizon as a promising alternative for enhancement of the production and productivity of Indian open-pit coal mines.

Jan 1, 2009

By Brad Hewitt, Jeff Belke

"Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. Four design aspects of the CCD circuit that have caused and continue to cause operational problems are:1. the inclusion of solution neutralisation gypsum in the CCD circuit feed which was designed solely for HPAL residue without proper investigation of its impact on the achievable underflow density and resulting wash efficiency;2. the decision to construct the thickener base from thickened solids;3. the lack of redundancy in the overflow, underflow and tailings pipe work; and4. the lack of thickener operational flexibility in the central rake-lift and feedwell dilution system.In November 2002, the lack of operational flexibility in the rake-lift and the feedwell dilution system through mechanical modification as follows:•, CCD1 has a modified rake mechanism that now allows central vertical lift of 600 mm;•, CCD1 has forced dilution using the Outokumpu Turbodil® technology and replacing the E-Duc® technology of Eimco;The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedwell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1 per cent (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2 per cent improvement in the circuit underflow density.The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil®dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary solution neutralisation improvements."

Jan 1, 2005

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology for supporting the Industry 4.0 has become the target of academic research in many sectors. This study reviewed the trends of open-source technology, its forms, and some industrial applications. As a case study using open-source hardware and software for the mining industry, this study proposed a low-cost environmental monitoring system for non-metallic underground mines to support mine safety and occupational health issues. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device. An open-source software, MIT App Inventor, was used for developing an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a non-metallic underground mining site to assess the performance of the system in both mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors still exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors

By Mokhinabonu Mardonova, Yosoon Choi

Open-source technology for supporting the Industry 4.0 has become the target of academic research in many sectors. This study reviewed the trends of open-source technology, its forms, and some industrial applications. As a case study using open-source hardware and software for the mining industry, this study proposed a low-cost environmental monitoring system for non-metallic underground mines to support mine safety and occupational health issues. The system was developed using open-source hardware, Arduino and 3D printer, to design the monitoring device. An open-source software, MIT App Inventor, was used for developing an Android application for smartphones to enable remote communication with the system. Field experiments were conducted at an underground tunnel and a non-metallic underground mining site to assess the performance of the system in both mobile and static modes, respectively. Although a few limitations related to the precision of the low-cost dust and gas sensors still exist, the findings of the experiments show that the mining industry can benefit from open-source technology deployment when considering cost factors

By T. T. Tomimatsu

[This Bureau of Mines paper investigates explores, and analyses the Corporate structure dynamics and Rancid role to evaluate the economic health of the U.S. copper producers. It highlights the Corporate policy options and measures of corporate profitability and suggests that a competitive domestic copper industry will exist in the future. The study highlights the activities of 14 selected major copper-producing companies, including their subsidiaries o affiliates, that were responsible for more than 95 percent of the total U.S. production in each of the years since 1969. The selected firms are hot all primarily in the business of producing copper. Several of the large producers are classified by the financial institutions as integrated oil and gas enterprises.]

Jan 1, 1980

By A. J. MacRae

Metallurgical furnaces are made up of complex multi-component systems that must function either together or in parallel for safe, and reliable operation. Thermal expansion of single material components experience induced stresses during heating and cooling, which can lead to cracking or failure. Multi component elements and systems can experience significant thermally induced stresses during both steady state and transient temperature conditions. Examples pertaining to temperature effects on refractory, copper cooling blocks, furnace shells, and complete systems will be discussed. The purpose of the paper is to highlight how stresses and strains are developed due to differential thermal expansion.

Jan 1, 2015

By R Hoskings

Conceptual studies of the run of mine stockpiling and reclaiming requirements commenced in 1975. Final selection of equipment was made in 1978 and the equipment was commissioned in June, 1979. Equipment selection was made after extensive investigation and visits to existing facilities throughout the world. The equipment selected is described and compared with the alternatives. Foundations were designed to minimise cleanup effort and to ensure stability of equipment under design wind loading without storm bays. Programmable logic control enables the stacking and reclaiming facility to provide a blended feed to the coal preparation plant.

Jan 1, 1980