Search Documents

By Y. Shu, A. R. Laplante

"A laboratory Knelson Concentrator (LKC), 7.5 cm in diameter, was used to study the performance of a similar unit at plant scale, 76 cm in diameter, This paper reports on sampling and assaying procedures and problems, and discusses the performance of the plant unit.The sampling procedure was based on the extraction of large samples, 5-15 kg, and their complete processing with a LKC, to characterize size-by-size performance. The procedure yielded reliable estimates of overall gold assays, after blatant assaying errors were corrected. The plant centrifugal unit concentrate was sampled in situ, which yielded very erratic grades, with a large overall negative bias. Due to the very heterogeneous nature of the concentrate, which can be linked to flow patterns in the riffles of the unit, it is recommended that for future testwork, the concentrate be recovered separately, blended and then sampled.The plant centrifugal separator, when operated at a feed rate of 25 t/h, yielded total and free gold recoveries of 41 % and 62%, respectively. This is much lower than previously reported data, and suggest that at 25 t/h, the unit is overloaded. However, recovery did not decrease with time over a loading cycle of 2 hours, which suggests that present loading cycles, generally 1 hour, can be significantly increased. INTRODUCTIONThe study of gold gravity circuits is plagued with the statistical problem of determining the behaviour of particles occurring with a very low frequency. This problem becomes particularly acute with increasing particle size. For example, considering the average weight of a gold flake in the 840-1200 µm (20/28 mesh) to be about 5 mg (Banisi et al, 1991), a reasonably high grade feed of 10 git would require, for a relative error (standard deviation) of 10% on grade, 100 particles, that is 0.5 g of gold, or 50 kg of 840-1200 µm material (a Poisson distribution is assumed). Gy's formula, for the same data, yields a weight of 33 kg, with a shape factor of 0.1 and a size distribution factor of 0.5. Both results are comparable; to obtain the suggested weight of material, a stream containing 5% weight in the 840-1200 µm would require 1 tonne samples (of unsized material). The problem rapidly disappears with decreasing particle size. Still with Banisi et al's data, a gold flake in the 300-420 µm range averages 0.5 mg in weight; the same 10% error on grade corresponds to a weight of 5 kg. Gy's formula for the same size distribution and particle shape factors as above predicts a required mass of 1.4 kg. This would correspond to an unsized sample weight of 10 kg with 14% weight in the 300-420 µm, for example."

Jan 1, 1992

By M. Hagfors

When establishing an underwater testing site for the energy measurements of the explosives, the dimensions of the measuring pool have to be measured to find out what is the maximum weight for the test charge. Secondly one has to decide the distance between the pressure gauge and the shooting point. Thirdly the pool has to be calibrated because of the reflections of the explosions by measuring the bubble periods of the calibration charges. The calibration shots can also be used to estimate the minimum weight of the explosive charge for the reliable energy measurements by calculating the shock, gas heave and total energy values and their standard deviations.

Jan 1, 2007

By Tom Martin

Mega projects present unique challenges with regard to estimating costs. With such projects, which may span decades, these challenges often begin as soon as a project is conceived. The importance of having a sound, resource based estimate avail-able early in the process cannot be overstated because it provides the basis for ongoing project decisions. For the final phase of providing an updated cost estimate, often while bidding by contractors is underway, the Engineer?s Estimate (EE) must incorporate present market conditions; account for possible volatile material price swings; be based on actual labor and fringe costs; rely on meaningful productivity rates; and accommodate any recent technology advances while identifying and allowing for risk factors. This paper explains the benefits associated with consultants adopting a contractor?s estimating approach when preparing the Engineer?s Estimate on mega projects like the various tunneling projects in New York City.

By William G. Szymczak

A set of experiments were conducted at the Aberdeen Proving Grounds [1] in which explosive charges were buried in saturated sand beneath a suspended rigid platform. The goal of these experiments was to measure the dependence of the impulse transmitted to the platform on the standoff distance and the charge burial depth. Simulations of these experiments were performed using the BUB2D axi-symmetric code using a frictional-cohesive visco-plastic model to describe the response of the saturated sand. This code solves a constrained set of conservation laws in which the liquid region (in this case saturated sand) is assumed incompressible. The explosion is initialized as a high pressure gas bubble (void) within the fluid. Comparisons of the simulations to the experiments are presented together with a study of the physical phenomenology associated with the loading process. In particular, it is shown that the force imparted to the platform is a combination of the impact of the sand on top of the explosion gas bubble and the pressure of the bubble as it expands before venting into the atmosphere. Under certain conditions, when the platform standoff is sufficiently small and the platform is sufficiently large, the bubble can over-expand before venting and pull the platform downward. This phenomenon was studied further through carefully measured and photographed small-scale experiments performed at the University of Maryland [2]. The small-scale experiments provide additional important validation benchmarks for our model.

Jan 1, 2005

By L. Bbosa

Paper written on project work carried out in partial fulfilment of BSc (Hons) (Eng) (Mechanical) degree Discrete element methods (DEM) are being used to provide detailed impact histories of the particles in comminution devices, such as mills. To match this immense detail of information, far more informative breakage tests than those that are generally conducted are now required. The split Hopkinson pressure bar apparatus is used in this study, as it allows the calculation of breakage forces and absorbed energies. The geometry of rock particles has been identified as significant, so this project undertook to identify the influence of shape on the breakage pattern of blue stone. Comparisons are then made between the breakage pattern of angular rocks and rounded, milled rocks for single impact fracture and consecutive impact loading at low energy. Results of this experiment indicate that although breakage for both geometries occurs over a similar energy range, rounded particles have the greater probability of fracture because they absorb more of the impact energy for a given loading. Size distributions of progeny show that five pebbles or more are sufficient to predict the distribution of most particles in small energy regimes. Cumulative impact testing shows that considerably more energy is required to break a rock through cumulative damage than through a single impact?this is of considerable importance in the light of the indications from DEM simulations that most breakage in a mill will be from cumulative damage rather than single impact breakage.

Jan 1, 2006

By Chris Breeds, Ken Johnston, Omar Fulton

This paper describes the process typically involved with obtaining permits for quarry blasting in urban, suburban, and rural areas, including: content of SEPA (State Environmental Policy Act) driven documentation; regulatory review and comment; public interaction; public hearing(s); periodic regulatory review(s); negotiated solutions; monitoring; and the role of public interaction, demonstration(s), and education in the process. Case studies will be presented of projects undertaken in the State of Washington that illustrate the approach and regulatory interaction as well as the importance of public interaction throughout the process. Reference will be made to the role of national and state regulations and local codes and ordinances that provide additional limitations on blasting practice. The paper will also present regional blast monitoring data that are used in the permitting process and the layout and design of blast monitoring systems typically required as conditions of the quarrying permit. Our presentation will include tools, which we have developed to assist with explaining blast related phenomenon to both regulators and the public.

Jan 1, 2003

By R G. Barker

The NZ Minerals Industry Association has continued to advance the interests of the minerals sector through leading the establishment of a Minerals Industry Advisory Committee, and the preparation of a technology strategy with funding assistance from the Foundation for Research, Science and Technology. The current moves mirror those of more than 30 years ago when a government initiative led to a resurgence of exploration through amending the mining legislation, redirecting Government research priorities and tax changes. The economic and political and commercial environment in 2001 is very different from that of the 1960s and success of these new initiatives depends on the continuing support and involvement of all sectors of the minerals industry, and building an improved relationship with the Government and the public.

Jan 1, 2001

By Tanveer Jahir

With increasing energy costs and mounting government pressure to adopt low emission, green sources of energy, it has become imperative to develop long-term sustainable underground infrastructures that exhibit low power consumption. Underground mining environments are mandated to have ventilation systems in place to replace polluted air with clean air. Continuously running air ventilation systems have proven to be an expensive solution for this requirement. Ventilation-on-demand (VOD) is a cost effective method for not only reducing energy consumption and greenhouse gasses, but also ensuring the safety and well-being of the miners beneath the surface. VOD is achieved by monitoring the air quality in target areas of the mine, and based on variables such as the number of personnel in the area, the number of emission-emitting vehicles, the air leakage around doors and entrances, dust levels, and other key environmental details, the speed and angles of the fan blades are adjusted to increase or decrease the volume of air flow. For over 40 years, Conspec Controls has been developing systems capable of VOD through the use of controllers, gas monitors and personnel/vehicle tracking equipment, providing inexpensive, reliable solutions for underground ventilation.

May 1, 2011

By R. Khanna, M. Dubikova

A variety of carbonaceous reducing materials are being used for the production of ferroalloys. Reductant materials include not just carbons such as coke, coal, char but also bio-carbons in form of charcoal produced from different types of wood. This paper discusses critical properties and reactions of carbonaceous materials and their significance in dictating reductant performance. Main considerations include among others, gasification of reductant, dissolution of carbon into molten metal, and direct reduction of slag by solid carbon. These are discussed in relation to material properties such as structural order, mineral matter content, composition, physical characteristics etc. A brief review of both conventional and novel approaches towards characterisation of carbonaceous materials has been included. Due to complexity and heterogeneity of carbonaceous reducing materials and a wide range of process requirements, the selection of the most appropriate reducing agent will depend on a number of considerations such as the availability of raw material and associated costs, product and process requirements and environmental aspects of waste gas emissions.

Jan 1, 2004

The Golden Cross mine commenced production in December 1991. Both open pit and underground mines produce 1000 tonnes of ore per day. Mining techniques are discussed along with results and variations to proposed methods of extracting the ore.

Jan 1, 1992

By Tatiana Ravani von Ow, Leandro Bomvisinho

"The size of mills driven by ring-gear or by a gearless solution has significantly increased in the last years. This has created additional challenges for the driven equipment. The requirements for the mechanical devices and the power grid have become more demanding. Controlled soft starting and operation, especially in dual pinion mills, as well as the protection of the equipment has gained importance. The selection of the drive solution for the mill therefore becomes more critical. Besides the classical criteria such as performance, efficiency and capital costs other factors come in the evaluation of the system such as flexibility and optimization of operation, reliability and the ageing of the grinding equipment.Variable speed solutions offer significant advantages over conventional fixed speed drives due to their application specific features and process optimization capabilities, even for ball mills where these are not seen yet as a must.The initial capital costs are higher than some of the direct on-line solutions however the benefits for the operation during the lifetime of the mill generated by the use of converter solutions justify the additional higher investment.INTRODUCTIONThe method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said; almost every decade in the last half century had its own trend. The trend was dominated by the market demand, by the process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology.All has started about 50 years ago with mill diameters less than 20 feet driven by fix speed synchronous or wound rotor motors with the power of about 2 MW. Around 10 years later, the mill sizes increased, but the necessary torque could not be transmitted by one pinion therefore dual pinion solutions were developed to power the mills. However, realization of the dual pinion solution was only possible when load could be evenly shared between the two pinions."

Jan 1, 2010

By Enrique Garay

Actualmente el geólogo de mina toma información rutinaria, mapea los bancos de la mina, los taladros para voladura y loguea los núcleos de perforación y fragmentos del aire reverso. Para la localización en el campo utiliza un GPS que tiene una estación en tierra que permite triangular en tiempo real. En ese sentido, el presente texto señala la importancia de la función del geólogo y las herramientas de campo que utiliza para la exploración y la definición del modelo geológico en la mina Pierina. Así para la digitalización del mapeo geológico utiliza el programa AutoCad, en el caso de mapeo de taladros para voladura emplea un Colector de Datos que posee una hoja de calculo que permite recoger datos del tipo de alteración, porcentaje de arcillas, dureza y tipo de mineralización. Finalmente, la información que genera el geólogo de mina es útil para diferentes usuarios ya que sirve para mejorar el cálculo de reservas, manejar el control eficiente del minado de mineral y desmonte, así como generar el soporte geológico a los geotecnistas responsables del estudio de estabilidad de taludes del tajo abierto, así como desde el punto de vista ambiental es posible definir zonas con potencial de generar drenaje ácido de rocas.

Aug 25, 2002

By François Girard

La zone 1 de la mine Doyon (zone altérée), se situe à l?extrémité sud de la mine et est constituée d?une série de veines étroites à fort pendage et ayant des épontes de très faible résistance. Les épontes supérieure et inférieure ont des valeurs de RQD variant de 0 à 20 lors que les valeurs de RQD de la zone minéralisée se situent entre 20 et 40. Le minerai de la zone 1 s?étend sur environ 300 m de long et sur 900 m de profondeur avec des épaisseurs variant entre 2 et 15 m. Des méthodes de minage long-trous y sont utilisées avec des accès longitudinaux ou transverses selon l?épaisseur de la zone minéralisée. L?exploitation de la zone 1 a débuté en 1991 et plus de 1,7 millions de tonnes auront été extraites à la fin 2008. Plusieurs techniques y ont été testées que ce soit au niveau du développement ou du minage afin d?améliorer la sécurité des travailleurs, de réduire la dilution des chantiers et d?en augmenter la récupération. Différentes modifications ont été apportées aux dimensions et orientations des galeries, aux patrons de forage, aux techniques de sautages, au support de terrain, à la séquence de minage et aux méthodes de remblayage. Le texte suivant élabore sur plusieurs approches utilisées lors du minage de la zone 1.

Feb 1, 2008

By B. J. Arnold, N. Terblanche

The features of the ‘Turbo’ froth flotation column will be discussed, including the double aeration system that improves flotation yield while not sacrificing grade, the internal launder system, and the unique feed/tailings sump that evens out flow to the flotation column preventing upset conditions. Results from various test programs and installations will be presented.

Jan 1, 2001

By A. Lane

The socio economic risks of mining in South Africa have been emerging for some time now, and have been brought into sharp relief by recent events in the platinum sector. The slow pace of social upliftment in the country has lead to widespread social unrest with consequent calls for different forms of resource nationalism. Fundamentally, the key stakeholders are not fully aligned, and are not engaging productively. This poses significant above-the-ground risk to mining companies. Measuring social impact, deploying inclusive solutions and engaging effectively with stakeholders are three ways in which mining companies can mitigate this risk.

Jan 1, 2013

By R. Thornton

Montana Tech is located in the historic mining town of Butte, MT and is adjacent to the Orphan Boy mine. This abandoned underground mine will be the heat source for a down-hole heat exchanger (DHE)/heat pump system. The mine was abandoned in the 1950?s and has since filled with water to within approximately 30 m of the surface. The shaft is composed of a 245 m vertical shaft connected with horizontal crosscut drifts at 60 m and 150 m below the water level that connect to a large stope with approximately 1250 million liters of water at a consistent 75-78°F temperature. The intent is to build this heating system to augment or fully heat a newly built 2,000 m2 building on the Montana Tech campus. As designed the system uses ?off-the-shelf? parts making the basic configuration straightforward with the exception of the DHE?s which need to be placed into the vertical shaft. Because there is little or no examples of placing the heat exchangers in a vertical shaft, the primary focus of this work was to model the heat exchanger placement and configuration in the vertical shaft such that thermal currents develop between the stope and vertical shaft in, via the horizontal crosscut drifts, in order to move the water and thereby provide the required energy. This study includes the modeling of water flow, temperature profiles, and the heat contribution from the surrounding rock walls.

Feb 27, 2013

By C. Musingwini

Traditionally, mineral reserves management at most underground mines in Zimbabwe focus on maintaining large mineral reserves so that the time between development and production is as long as possible. Historical data at Shabanie mine, a Zimbabwean sub-level caving underground mining operation, confirms this practice. However, the high cost of underground development means that the luxury of large buffer mineral reserves cannot be justified. Furthermore significant increases in the costs of production, exacerbated by the current unfavourable economic climate, make the wisdom of extending development workings well ahead of use questionable. Poor ground conditions at Shabanie mine, mean that some development ends have to be re-mined two or three times due to partial or complete closure between the time they are mined and the time they are utilized. In order to reduce the inordinately high support costs associated with closure of development ends a new ?just-in-time? (JIT) approach that provides development ends as and when they are needed, has been adopted. Accordingly a model to determine an appropriate ?just-in-time? rate of development has been created. The JIT development model indicated that the mine could reduce development rates from 330 m/month in 2001, to 160 m/month in 2002 and achieve savings of about 50% on annual support costs, but still assure customers of a long-term product supply. The mine accepted the model in November 2001 and began implementing it in 2002. Results of the implementation will be reviewed in 2003.

Jan 1, 2003

By Enrique Touceda

FOR a number of years prior to the world war, the firm of Geo. H. Thacher & Co., of Albany, N. Y., was engaged in the manufacture of marine and other gray-iron castings. At -the outbreak of the war the firm decided to specialize in the manufacture f propeller wheels. It attacked the problem, therefore, from a foundry point of view, seeking to produce a casting that would be so accurate that no subsequent machining would be required on the blades, also from the point of view of the ship builder. There were two general methods f manufacture, the shortcomings of which have been freely acknowledged. In the sweep method, the nowel, or bottom half-mold, for each blade is swept up by a spindle beam and pitch race, while the top half-mold for each blade is built up individually. In the pattern method one individual blade, with the hub or hub portion, is mounted on a spindle and the individual -blade mold formed, the pattern is then rotated on the spindle to the position- for the next blade, etc. In rare cases wheels were made from a solid pattern. Owing to the cost of the pattern, its failure in many instances to be correctly made, and (when made of wood) its early and sure distortion the disadvantage of this practice is obvious, while metal patterns in most instances were prohibitive in cost. In these methods both green-sand and loam molding was practiced. The casting produced by either method can be considered only as a blank from which the propeller must be machined. The back surface f each blade must be chipped too the templet and through this procedure chipped to such accuracy, as will be required for a static balance. Inasmuch as the' work done by the machine tool is confined to the driving face of the blades, not only is perfection most difficult, but corrosion will be greater because of the removal of the dense skin f the casting and the local strains set up by the pneumatic tool in chipping. To produce a finished 9-ft. propeller for a Navy destroyer required from 8 to 21 days f foundry work and about the same length of, time for the machining. Through the use f the Thacher process, only as many hours are required, besides it is possible to produce a finished casting in perfect conformity, with any particular propeller-wheel design,

Jan 4, 1921

By Fumihiko Sumiya, Hideki Hamashima, Shigeru Itoh, Shinya Tanaka

The detonation characteristics of non-ideal explosives, especially the emulsion explosives, are critically affected by the confinement of case. In this study, we focused the shock wave propagating in case as confinement factor. Therefore, the objective of this study was to obtain a better understanding of the influence of shock wave propagating in case on the detonation characteristics of explosives in laboratory scale.

Jan 1, 2007

By M. S. Smith

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The condition of tunnels at Premier has deteriorated to such an extent that an objective viewpoint on what leads to poor condition was required. Poor and untimely development results in schedule deviation, rehabilitation, and increased working costs. The project focused primarily on quality, and not on efficiency. The project gave management guidelines that need to be focused on in order to produce quality infrastructure. The conclusions were reached by doing literature searches, underground site investigations, benchmarking and computer simulations. From the results we can see that, in order to produce good quality tunnels, we have to have the basics working. This was found to be one of the major problems. Firstly, tunnel profiles are not to the design specification and no fixed blast designs existed. After revising tunnel profile statistics, over break increased to 10% (previously 7%) and development metres were 50 m short of target. Blasting was not monitored and designs not optimized for the conditions. Furthermore, geological factors are the main contributor to tunnel failure, although this process is initiated and aided by poor development (overbroken tunnels, incorrect profiles, direction and location) and blast damage. Continuing to develop tunnels in the current manner will cost R 1.5 million in additional costs for loading and supporting overbreak, whilst an additional 1 800 man-shifts will be required. Blast patterns were designed as a starting point for trials, while the implementation of a blast management system, development statistical database, tunnel hand-over procedures and a revision of the bonus system were proposed.

Jan 1, 2004